| /external/u-boot/arch/arm/mach-tegra/tegra210/ |
| D | Kconfig | 20 HDMI, USB micro-B port, Ethernet via USB3, USB3 host port, SATA,
29 card slot, HDMI, USB micro-B port, Ethernet via USB3, USB3 host
|
| D | clock.c | 431 NONE(USB3),
|
| /external/u-boot/drivers/usb/dwc3/ |
| D | Kconfig | 2 bool "DesignWare USB3 DRD Core Support"
6 USB controller based on the DesignWare USB3 IP Core.
47 bool "DesignWare USB3 Host Support on UniPhier Platforms"
58 Enable single driver for both USB2 PHY programming and USB3 PHY
|
| /external/autotest/server/site_tests/firmware_TypeCProbeUSB3/ |
| D | control | 10 CRITERIA = "This test will fail if DUT can't probe USB3 device on type C port."
18 This test remotely switches type C port to USB3 device mode. It fails if
19 DUT can't probe the USB3 super speed device on Plankton.
|
| /external/u-boot/board/theobroma-systems/puma_rk3399/ |
| D | README | 17 * USB3.0 dual role port
18 * 2x USB3.0 host, 1x USB2.0 host via onboard USB3.0 hub
|
| /external/u-boot/drivers/usb/host/ |
| D | Kconfig | 19 bool "DesignWare USB3 DRD Core Support"
22 USB controller based on the DesignWare USB3 IP Core.
25 bool "DesignWare USB3 DRD Generic OF Simple Glue Layer"
30 USB controller based on the DesignWare USB3 IP Core.
|
| /external/u-boot/arch/arm/mach-mvebu/serdes/a38x/ |
| D | high_speed_env_spec.c | 1171 serdes_seq_db[USB3_POWER_UP_SEQ].data_arr_idx = USB3; in hws_serdes_seq_db_init()
1203 serdes_seq_db[USB3_ELECTRICAL_CONFIG_SEQ].data_arr_idx = USB3; in hws_serdes_seq_db_init()
1210 serdes_seq_db[USB3_TX_CONFIG_SEQ1].data_arr_idx = USB3; in hws_serdes_seq_db_init()
1217 serdes_seq_db[USB3_TX_CONFIG_SEQ2].data_arr_idx = USB3; in hws_serdes_seq_db_init()
1224 serdes_seq_db[USB3_TX_CONFIG_SEQ3].data_arr_idx = USB3; in hws_serdes_seq_db_init()
1579 if (serdes_type == USB3) { in serdes_pex_usb3_pipe_delay_w_a()
1793 (serdes_num, USB3)); in serdes_power_up_ctrl()
|
| D | high_speed_env_spec.h | 172 USB3, enumerator
|
| /external/u-boot/arch/arm/mach-tegra/tegra186/ |
| D | Kconfig | 16 micro-B port, Ethernet, USB3 host port, SATA, PCIe, and two GPIO
|
| /external/u-boot/board/intel/ |
| D | Kconfig | 16 4GB memory, HDMI/DP/VGA display, HD audio, SATA, USB2, USB3, SD, eMMC,
34 peripheral connectors for PCIe/SATA/USB2/USB3/LAN/UART/PS2/VGA/HDMI.
|
| /external/u-boot/doc/device-tree-bindings/phy/ |
| D | phy-stih407-usb.txt | 3 …s file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3
|
| /external/u-boot/drivers/phy/ |
| D | Kconfig | 110 used by USB2 and USB3 Host controllers available on
132 USB2 and USB3 PHYS.
|
| /external/u-boot/arch/arm/dts/ |
| D | armada-388-helios4.dts | 152 * 5-USB3 overcurrent
153 * 6-USB3 power
|
| D | armada-388-clearfog.dts | 134 * 5-USB3 overcurrent
135 * 6-USB3 power
|
| /external/autotest/server/site_tests/kernel_ExternalUsbPeripheralsDetectionTest/ |
| D | control | 32 - USB3.0 Card Reader
|
| /external/u-boot/drivers/phy/marvell/ |
| D | comphy_a3700.c | 353 reg_set16(phy_addr(USB3, reg), data, mask); in usb3_reg_set16()
494 ret = comphy_poll_reg(phy_addr(USB3, LANE_STAT1), /* address */ in comphy_usb3_power_up()
|
| D | comphy_a3700.h | 75 USB3 = 2, enumerator
|
| /external/u-boot/board/google/ |
| D | Kconfig | 39 includes a USB SD reader, four USB3 ports, display port and HDMI
|
| /external/u-boot/board/rockchip/evb_rk3399/ |
| D | README | 12 * USB: USB3.0 typc-C port *2 with dwc3 controller
|
| /external/walt/android/WALT/app/src/main/jni/ |
| D | README.md | 68 - Same Linux machine, USB3 port: ~800us
|
| /external/u-boot/arch/arm/mach-tegra/tegra20/ |
| D | clock.c | 318 NONE(USB3),
|
| /external/u-boot/arch/arm/mach-tegra/tegra114/ |
| D | clock.c | 300 NONE(USB3),
|
| /external/u-boot/arch/arm/mach-tegra/tegra30/ |
| D | clock.c | 300 NONE(USB3),
|
| /external/u-boot/arch/arm/cpu/armv8/fsl-layerscape/doc/ |
| D | README.soc | 71 - 3 PCIe3.0 , 1 SATA3.0, 2 USB3.0, 1 SDXC, 2 DUARTs etc
|
| /external/u-boot/arch/arm/mach-tegra/tegra124/ |
| D | clock.c | 400 NONE(USB3),
|