| /external/u-boot/drivers/usb/gadget/ |
| D | composite.c | 194 if (speed == USB_SPEED_HIGH) in config_buf()
222 if (gadget->speed == USB_SPEED_HIGH) in config_desc()
227 speed = USB_SPEED_HIGH; in config_desc()
232 if (speed == USB_SPEED_HIGH) { in config_desc()
254 if (gadget->speed == USB_SPEED_HIGH) in count_configs()
342 case USB_SPEED_HIGH: in set_config()
369 if (gadget->speed == USB_SPEED_HIGH) in set_config()
1052 .speed = USB_SPEED_HIGH,
|
| D | ether.c | 195 #define DEVSPEED USB_SPEED_HIGH
205 (DEFAULT_QLEN*((gadget->speed == USB_SPEED_HIGH) ? qmult : 1))
209 return (g->speed == USB_SPEED_HIGH) ? HS_BPS : FS_BPS; in BITRATE()
830 if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH) in ep_desc()
894 hs = (g->speed == USB_SPEED_HIGH); in config_buf()
1100 case USB_SPEED_HIGH: in eth_set_config()
1743 req->no_interrupt = (dev->gadget->speed == USB_SPEED_HIGH)
2485 req->no_interrupt = (dev->gadget->speed == USB_SPEED_HIGH) in _usb_eth_send()
|
| D | dwc2_udc_otg.c | 240 && driver->speed != USB_SPEED_HIGH) in usb_gadget_register_driver()
516 if (speed == USB_SPEED_HIGH) { in set_max_pktsize()
520 dev->gadget.speed = USB_SPEED_HIGH; in set_max_pktsize()
|
| D | storage_common.c | 537 if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH) in fsg_ep_desc()
|
| D | f_fastboot.c | 113 if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH) in fb_ep_desc()
|
| D | ci_udc.c | 819 speed = USB_SPEED_HIGH; in udc_irq()
1008 if (driver->speed != USB_SPEED_FULL && driver->speed != USB_SPEED_HIGH) in usb_gadget_register_driver()
|
| D | atmel_usba_udc.c | 1131 udc->gadget.speed = USB_SPEED_HIGH; in usba_udc_irq()
1195 .speed = USB_SPEED_HIGH,
|
| /external/u-boot/board/st/stih410-b2260/ |
| D | board.c | 44 .maximum_speed = USB_SPEED_HIGH,
|
| /external/u-boot/drivers/usb/emul/ |
| D | sandbox_hub.c | 149 *speed = USB_SPEED_HIGH; in hub_find_device()
181 else if (speed == USB_SPEED_HIGH) in clrset_post_state()
|
| /external/u-boot/drivers/usb/common/ |
| D | common.c | 46 [USB_SPEED_HIGH] = "high-speed",
|
| /external/u-boot/board/intel/edison/ |
| D | edison.c | 20 .maximum_speed = USB_SPEED_HIGH,
|
| /external/u-boot/include/linux/usb/ |
| D | composite.h | 147 if (gadget_is_dualspeed(g) && g->speed == USB_SPEED_HIGH) in ep_choose()
|
| D | ch9.h | 953 USB_SPEED_HIGH, /* usb 2.0 */ enumerator
|
| /external/u-boot/drivers/usb/host/ |
| D | xhci-mem.c | 771 case USB_SPEED_HIGH: in xhci_setup_addressable_virt_dev()
797 } while (dev->speed != USB_SPEED_HIGH); in xhci_setup_addressable_virt_dev()
827 case USB_SPEED_HIGH: in xhci_setup_addressable_virt_dev()
|
| D | usb-sandbox.c | 128 udev->speed = USB_SPEED_HIGH; in sandbox_alloc_device()
|
| D | xhci.c | 336 case USB_SPEED_HIGH: in xhci_get_endpoint_interval()
405 if (udev->speed == USB_SPEED_HIGH && in xhci_get_endpoint_max_burst()
1460 if (udev->speed == USB_SPEED_HIGH) in xhci_update_hub_device()
|
| D | ehci-hcd.c | 277 if (speed == USB_SPEED_HIGH) in ehci_encode_speed()
407 c = (dev->speed != USB_SPEED_HIGH) && !usb_pipeendpoint(pipe); in ehci_submit_async()
999 QH_ENDPT1_EPS(USB_SPEED_HIGH)); in ehci_common_init()
1164 dev->speed = USB_SPEED_HIGH; in _ehci_submit_control_msg()
|
| D | dwc2.c | 940 if (dev->speed != USB_SPEED_HIGH) { in chunk_msg()
1061 dev->speed = USB_SPEED_HIGH; in _submit_control_msg()
|
| /external/u-boot/board/ti/am43xx/ |
| D | board.c | 702 .maximum_speed = USB_SPEED_HIGH,
720 .maximum_speed = USB_SPEED_HIGH,
|
| /external/u-boot/drivers/usb/musb-new/ |
| D | musb_gadget_ep0.c | 310 if (musb->g.speed != USB_SPEED_HIGH) in service_zero_data_request()
800 ? USB_SPEED_HIGH : USB_SPEED_FULL; in musb_g_ep0_irq()
|
| D | musb_uboot.c | 205 USB_SPEED_HIGH : in _musb_reset_root_port()
|
| D | musb_gadget.c | 1892 musb->g.max_speed = USB_SPEED_HIGH; in musb_gadget_setup()
1971 if (driver->max_speed < USB_SPEED_HIGH) in musb_gadget_start()
2276 ? USB_SPEED_HIGH : USB_SPEED_FULL; in musb_g_reset()
|
| /external/u-boot/common/ |
| D | usb.c | 1243 while (uparent->speed != USB_SPEED_HIGH) { in usb_find_usb2_hub_address_port()
1266 if (udev->parent->speed != USB_SPEED_HIGH) { in usb_find_usb2_hub_address_port()
|
| /external/u-boot/cmd/ |
| D | usb.c | 327 case USB_SPEED_HIGH: in portspeed()
|
| /external/kernel-headers/original/uapi/linux/usb/ |
| D | ch9.h | 1140 USB_SPEED_HIGH, /* usb 2.0 */ enumerator
|