README
1Overview
2=========
3C29XPCIE board is a series of Freescale PCIe add-in cards to perform
4as public key crypto accelerator or secure key management module.
5It includes C293PCIE board, C293PCIE board and C291PCIE board.
6The Freescale C29x family is a high performance crypto co-processor.
7It combines a single e500v2 core with necessary SEC engines.
8(maximum core frequency 1000/1200 MHz).
9
10The C29xPCIE board features are as follows:
11Memory subsystem:
12 - 512Mbyte unbuffered DDR3 SDRAM discrete devices (32-bit bus)
13 - 64 Mbyte NOR flash single-chip memory
14 - 4 Gbyte NAND flash memory
15 - 1 Mbit AT24C1024 I2C EEPROM
16 - 16 Mbyte SPI memory
17
18Interfaces:
19 - 10/100/1000 BaseT Ethernet ports:
20 - eTSEC1, RGMII: one 10/100/1000 port
21 - eTSEC2, RGMII: one 10/100/1000 port
22 - DUART interface:
23 - DUART interface: supports two UARTs up to 115200 bps for
24 console display
25
26Board connectors:
27 - Mini-ITX power supply connector
28 - JTAG/COP for debugging
29
30Physical Memory Map on C29xPCIE
31===============================
32Address Start Address End Memory type
330x0_0000_0000 - 0x0_1fff_ffff 512MB DDR
340xc_0000_0000 - 0xc_8fff_ffff 256MB PCIE memory
350xf_ec00_0000 - 0xf_efff_ffff 64MB NOR flash
360xf_ffb0_0000 - 0xf_ffb7_ffff 512KB SRAM
370xf_ffc0_0000 - 0xf_ffc0_ffff 64KB PCIE IO
380xf_ffdf_0000 - 0xf_ffdf_0fff 4KB CPLD
390xf_ffe0_0000 - 0xf_ffef_ffff 1MB CCSR
40
41Serial Port Configuration on C29xPCIE
42=====================================
43Configure the serial port of the attached computer with the following values:
44 -Data rate: 115200 bps
45 -Number of data bits: 8
46 -Parity: None
47 -Number of Stop bits: 1
48 -Flow Control: Hardware/None
49
50Settings of DIP-switch
51======================
52 SW5[1:4]= 1111 and SW5[6]=0 for boot from 16bit NOR flash
53 SW5[1:4]= 0110 and SW5[6]=0 for boot from SPI flash
54Note: 1 stands for 'off', 0 stands for 'on'
55
56Build and program U-Boot to NOR flash
57==================================
581. Build u-boot.bin image example:
59 export ARCH=powerpc
60 export CROSS_COMPILE=/your_path/powerpc-linux-gnu-
61 make C293PCIE
62
632. Program u-boot.bin into NOR flash
64 => tftp $loadaddr $uboot
65 => protect off eff40000 +$filesize
66 => erase eff40000 +$filesize
67 => cp.b $loadaddr eff40000 $filesize
68
693. Check SW5[1:4]= 1111 and SW5[6]=0, then power on.
70
71Alternate NOR bank
72==================
73There are four banks in C29XPCIE board, example to change bank booting:
741. Program u-boot.bin into alternate NOR bank
75 => tftp $loadaddr $uboot
76 => protect off e9f40000 +$filesize
77 => erase e9f40000 +$filesize
78 => cp.b $loadaddr e9f40000 $filesize
79
802. Switch to alternate NOR bank
81 => cpld_cmd reset altbank [bank]
82 - [bank] bank value select 1-4
83 - bank 1 on the flash 0x0000000~0x0ffffff
84 - bank 2 on the flash 0x1000000~0x1ffffff
85 - bank 3 on the flash 0x2000000~0x2ffffff
86 - bank 4 on the flash 0x3000000~0x3ffffff
87 or set SW5[7]= ON/OFF and SW5[7]= ON/OFF, then power on again.
88
89Build and program U-Boot to SPI flash
90==================================
911. Build u-boot-spi.bin image
92 make C29xPCIE_SPIFLASH_config; make
93 Need the boot_format tool to generate u-boot-spi.bin from the u-boot.bin.
94
952. Program u-boot-spi.bin into SPI flash
96 => tftp $loadaddr $uboot-spi
97 => sf erase 0 100000
98 => sf write $loadaddr 0 $filesize
99
1003. Check SW5[1:4]= 0110 and SW5[6]=0, then power on.
101