1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * SH7751 PCI Controller (PCIC) for U-Boot.
4 * (C) Dustin McIntire (dustin@sensoria.com)
5 * (C) 2007,2008 Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
6 */
7
8 #include <common.h>
9 #include <pci.h>
10 #include <asm/processor.h>
11 #include <asm/io.h>
12 #include <asm/pci.h>
13
14 /* Register addresses and such */
15 #define SH7751_BCR1 (vu_long *)0xFF800000
16 #define SH7751_BCR2 (vu_short *)0xFF800004
17 #define SH7751_WCR1 (vu_long *)0xFF800008
18 #define SH7751_WCR2 (vu_long *)0xFF80000C
19 #define SH7751_WCR3 (vu_long *)0xFF800010
20 #define SH7751_MCR (vu_long *)0xFF800014
21 #define SH7751_BCR3 (vu_short *)0xFF800050
22 #define SH7751_PCICONF0 (vu_long *)0xFE200000
23 #define SH7751_PCICONF1 (vu_long *)0xFE200004
24 #define SH7751_PCICONF2 (vu_long *)0xFE200008
25 #define SH7751_PCICONF3 (vu_long *)0xFE20000C
26 #define SH7751_PCICONF4 (vu_long *)0xFE200010
27 #define SH7751_PCICONF5 (vu_long *)0xFE200014
28 #define SH7751_PCICONF6 (vu_long *)0xFE200018
29 #define SH7751_PCICR (vu_long *)0xFE200100
30 #define SH7751_PCILSR0 (vu_long *)0xFE200104
31 #define SH7751_PCILSR1 (vu_long *)0xFE200108
32 #define SH7751_PCILAR0 (vu_long *)0xFE20010C
33 #define SH7751_PCILAR1 (vu_long *)0xFE200110
34 #define SH7751_PCIMBR (vu_long *)0xFE2001C4
35 #define SH7751_PCIIOBR (vu_long *)0xFE2001C8
36 #define SH7751_PCIPINT (vu_long *)0xFE2001CC
37 #define SH7751_PCIPINTM (vu_long *)0xFE2001D0
38 #define SH7751_PCICLKR (vu_long *)0xFE2001D4
39 #define SH7751_PCIBCR1 (vu_long *)0xFE2001E0
40 #define SH7751_PCIBCR2 (vu_long *)0xFE2001E4
41 #define SH7751_PCIWCR1 (vu_long *)0xFE2001E8
42 #define SH7751_PCIWCR2 (vu_long *)0xFE2001EC
43 #define SH7751_PCIWCR3 (vu_long *)0xFE2001F0
44 #define SH7751_PCIMCR (vu_long *)0xFE2001F4
45 #define SH7751_PCIBCR3 (vu_long *)0xFE2001F8
46
47 #define BCR1_BREQEN 0x00080000
48 #define PCI_SH7751_ID 0x35051054
49 #define PCI_SH7751R_ID 0x350E1054
50 #define SH7751_PCICONF1_WCC 0x00000080
51 #define SH7751_PCICONF1_PER 0x00000040
52 #define SH7751_PCICONF1_BUM 0x00000004
53 #define SH7751_PCICONF1_MES 0x00000002
54 #define SH7751_PCICONF1_CMDS 0x000000C6
55 #define SH7751_PCI_HOST_BRIDGE 0x6
56 #define SH7751_PCICR_PREFIX 0xa5000000
57 #define SH7751_PCICR_PRST 0x00000002
58 #define SH7751_PCICR_CFIN 0x00000001
59 #define SH7751_PCIPINT_D3 0x00000002
60 #define SH7751_PCIPINT_D0 0x00000001
61 #define SH7751_PCICLKR_PREFIX 0xa5000000
62
63 #define SH7751_PCI_MEM_BASE 0xFD000000
64 #define SH7751_PCI_MEM_SIZE 0x01000000
65 #define SH7751_PCI_IO_BASE 0xFE240000
66 #define SH7751_PCI_IO_SIZE 0x00040000
67
68 #define SH7751_PCIPAR (vu_long *)0xFE2001C0
69 #define SH7751_PCIPDR (vu_long *)0xFE200220
70
71 #define p4_in(addr) (*addr)
72 #define p4_out(data, addr) (*addr) = (data)
73
74 /* Double word */
pci_sh4_read_config_dword(struct pci_controller * hose,pci_dev_t dev,int offset,u32 * value)75 int pci_sh4_read_config_dword(struct pci_controller *hose,
76 pci_dev_t dev, int offset, u32 *value)
77 {
78 u32 par_data = 0x80000000 | dev;
79
80 p4_out(par_data | (offset & 0xfc), SH7751_PCIPAR);
81 *value = p4_in(SH7751_PCIPDR);
82
83 return 0;
84 }
85
pci_sh4_write_config_dword(struct pci_controller * hose,pci_dev_t dev,int offset,u32 value)86 int pci_sh4_write_config_dword(struct pci_controller *hose,
87 pci_dev_t dev, int offset, u32 value)
88 {
89 u32 par_data = 0x80000000 | dev;
90
91 p4_out(par_data | (offset & 0xfc), SH7751_PCIPAR);
92 p4_out(value, SH7751_PCIPDR);
93
94 return 0;
95 }
96
pci_sh7751_init(struct pci_controller * hose)97 int pci_sh7751_init(struct pci_controller *hose)
98 {
99 /* Double-check that we're a 7751 or 7751R chip */
100 if (p4_in(SH7751_PCICONF0) != PCI_SH7751_ID
101 && p4_in(SH7751_PCICONF0) != PCI_SH7751R_ID) {
102 printf("PCI: Unknown PCI host bridge.\n");
103 return 1;
104 }
105 printf("PCI: SH7751 PCI host bridge found.\n");
106
107 /* Double-check some BSC config settings */
108 /* (Area 3 non-MPX 32-bit, PCI bus pins) */
109 if ((p4_in(SH7751_BCR1) & 0x20008) == 0x20000) {
110 printf("SH7751_BCR1 value is wrong(0x%08X)\n",
111 (unsigned int)p4_in(SH7751_BCR1));
112 return 2;
113 }
114 if ((p4_in(SH7751_BCR2) & 0xC0) != 0xC0) {
115 printf("SH7751_BCR2 value is wrong(0x%08X)\n",
116 (unsigned int)p4_in(SH7751_BCR2));
117 return 3;
118 }
119 if (p4_in(SH7751_BCR2) & 0x01) {
120 printf("SH7751_BCR2 value is wrong(0x%08X)\n",
121 (unsigned int)p4_in(SH7751_BCR2));
122 return 4;
123 }
124
125 /* Force BREQEN in BCR1 to allow PCIC access */
126 p4_out((p4_in(SH7751_BCR1) | BCR1_BREQEN), SH7751_BCR1);
127
128 /* Toggle PCI reset pin */
129 p4_out((SH7751_PCICR_PREFIX | SH7751_PCICR_PRST), SH7751_PCICR);
130 udelay(32);
131 p4_out(SH7751_PCICR_PREFIX, SH7751_PCICR);
132
133 /* Set cmd bits: WCC, PER, BUM, MES */
134 /* (Addr/Data stepping, Parity enabled, Bus Master, Memory enabled) */
135 p4_out(0xfb900047, SH7751_PCICONF1); /* K.Kino */
136
137 /* Define this host as the host bridge */
138 p4_out((SH7751_PCI_HOST_BRIDGE << 24), SH7751_PCICONF2);
139
140 /* Force PCI clock(s) on */
141 p4_out(0, SH7751_PCICLKR);
142 p4_out(0x03, SH7751_PCICLKR);
143
144 /* Clear powerdown IRQs, also mask them (unused) */
145 p4_out((SH7751_PCIPINT_D0 | SH7751_PCIPINT_D3), SH7751_PCIPINT);
146 p4_out(0, SH7751_PCIPINTM);
147
148 p4_out(0xab000001, SH7751_PCICONF4);
149
150 /* Set up target memory mappings (for external DMA access) */
151 /* Map both P0 and P2 range to Area 3 RAM for ease of use */
152 p4_out(CONFIG_SYS_SDRAM_SIZE - 0x100000, SH7751_PCILSR0);
153 p4_out(CONFIG_SYS_SDRAM_BASE & 0x1FF00000, SH7751_PCILAR0);
154 p4_out(CONFIG_SYS_SDRAM_BASE & 0xFFF00000, SH7751_PCICONF5);
155
156 p4_out(0, SH7751_PCILSR1);
157 p4_out(0, SH7751_PCILAR1);
158 p4_out(0xd0000000, SH7751_PCICONF6);
159
160 /* Map memory window to same address on PCI bus */
161 p4_out(SH7751_PCI_MEM_BASE, SH7751_PCIMBR);
162
163 /* Map IO window to same address on PCI bus */
164 p4_out(SH7751_PCI_IO_BASE, SH7751_PCIIOBR);
165
166 /* set BREQEN */
167 p4_out(inl(SH7751_BCR1) | 0x00080000, SH7751_BCR1);
168
169 /* Copy BSC registers into PCI BSC */
170 p4_out(inl(SH7751_BCR1), SH7751_PCIBCR1);
171 p4_out(inw(SH7751_BCR2), SH7751_PCIBCR2);
172 p4_out(inw(SH7751_BCR3), SH7751_PCIBCR3);
173 p4_out(inl(SH7751_WCR1), SH7751_PCIWCR1);
174 p4_out(inl(SH7751_WCR2), SH7751_PCIWCR2);
175 p4_out(inl(SH7751_WCR3), SH7751_PCIWCR3);
176 p4_out(inl(SH7751_MCR), SH7751_PCIMCR);
177
178 /* Finally, set central function init complete */
179 p4_out((SH7751_PCICR_PREFIX | SH7751_PCICR_CFIN), SH7751_PCICR);
180
181 pci_sh4_init(hose);
182
183 return 0;
184 }
185