1if ARCH_ZYNQMP 2 3config SPL_FS_FAT 4 default y 5 6config SPL_LIBCOMMON_SUPPORT 7 default y 8 9config SPL_LIBDISK_SUPPORT 10 default y 11 12config SPL_LIBGENERIC_SUPPORT 13 default y 14 15config SPL_MMC_SUPPORT 16 default y if MMC_SDHCI_ZYNQ 17 18config SPL_SERIAL_SUPPORT 19 default y 20 21config SPL_SPI_FLASH_SUPPORT 22 default y if ZYNQ_QSPI 23 24config SPL_SPI_SUPPORT 25 default y if ZYNQ_QSPI 26 27config SYS_BOARD 28 default "zynqmp" 29 30config SYS_VENDOR 31 string "Vendor name" 32 default "xilinx" 33 34config SYS_SOC 35 default "zynqmp" 36 37config SYS_CONFIG_NAME 38 string "Board configuration name" 39 default "xilinx_zynqmp" 40 help 41 This option contains information about board configuration name. 42 Based on this option include/configs/<CONFIG_SYS_CONFIG_NAME>.h header 43 will be used for board configuration. 44 45config SYS_MEM_RSVD_FOR_MMU 46 bool "Reserve memory for MMU Table" 47 help 48 If defined this option is used to setup different space for 49 MMU table than the one which will be allocated during 50 relocation. 51 52config BOOT_INIT_FILE 53 string "boot.bin init register filename" 54 depends on SPL 55 default "" 56 help 57 Add register writes to boot.bin format (max 256 pairs). 58 Expect a table of register-value pairs, e.g. "0x12345678 0x4321" 59 60config PMUFW_INIT_FILE 61 string "PMU firmware" 62 depends on SPL 63 default "" 64 help 65 Include external PMUFW (Platform Management Unit FirmWare) to 66 a Xilinx bootable image (boot.bin). 67 68config ZYNQMP_SPL_PM_CFG_OBJ_FILE 69 string "PMU firmware configuration object to load at runtime by SPL" 70 depends on SPL 71 help 72 Path to a binary PMU firmware configuration object to be linked 73 into U-Boot SPL and loaded at runtime into the PMU firmware. 74 75 The ZynqMP Power Management Unit (PMU) needs a configuration 76 object for most SoC peripherals to work. To have it loaded by 77 U-Boot SPL set here the file name (absolute path or relative to 78 the top source tree) of your configuration, which must be a 79 binary blob. It will be linked in the SPL binary and loaded 80 into the PMU firmware by U-Boot SPL during board 81 initialization. 82 83 Leave this option empty if your PMU firmware has a hard-coded 84 configuration object or you are loading it by any other means. 85 86config ZYNQMP_USB 87 bool "Configure ZynqMP USB" 88 89config ZYNQMP_NO_DDR 90 bool "Disable DDR MMU mapping" 91 help 92 This option configures MMU with no DDR to avoid speculative 93 access to DDR memory where DDR is not present. 94 95config SYS_MALLOC_F_LEN 96 default 0x600 97 98config DEFINE_TCM_OCM_MMAP 99 bool "Define TCM and OCM memory in MMU Table" 100 default y if MP 101 help 102 This option if enabled defines the TCM and OCM memory and its 103 memory attributes in MMU table entry. 104 105config ZYNQMP_PSU_INIT_ENABLED 106 bool "Include psu_init" 107 help 108 Include psu_init to full u-boot. SPL include psu_init by default. 109 110config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED 111 bool "Overwrite SPL bootmode" 112 depends on SPL 113 help 114 Overwrite bootmode selected via boot mode pins to tell SPL what should 115 be the next boot device. 116 117config ZYNQ_SDHCI_MAX_FREQ 118 default 200000000 119 120config SPL_ZYNQMP_TWO_SDHCI 121 bool "Enable booting from both SDHCIs" 122 depends on SPL 123 help 124 This option reflects that board has two SDHCI controllers which 125 platform can use as boot device. This option ensures that SPL will 126 setup BOOT_DEVICE_MMC2 for SDHCI1 controller and BOOT_DEVICE_MMC1 for 127 SDHCI0 controller. Platforms which have only one SDHCI controller 128 shouldn't enable this option because it for software SDHCI0 or SDHCI1 129 are both covered by BOOT_DEVICE_MMC1. 130 131config SPL_ZYNQMP_ALT_BOOTMODE 132 hex 133 default 0x0 if JTAG_MODE 134 default 0x1 if QSPI_MODE_24BIT 135 default 0x2 if QSPI_MODE_32BIT 136 default 0x3 if SD_MODE 137 default 0x4 if NAND_MODE 138 default 0x5 if SD_MODE1 139 default 0x6 if EMMC_MODE 140 default 0x7 if USB_MODE 141 default 0xa if SW_USBHOST_MODE 142 default 0xb if SW_SATA_MODE 143 default 0xe if SD1_LSHFT_MODE 144 145choice 146 prompt "Boot mode" 147 depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED 148 default JTAG_MODE 149 150config JTAG_MODE 151 bool "JTAG_MODE" 152 153config QSPI_MODE_24BIT 154 bool "QSPI_MODE_24BIT" 155 156config QSPI_MODE_32BIT 157 bool "QSPI_MODE_32BIT" 158 159config SD_MODE 160 bool "SD_MODE" 161 162config SD_MODE1 163 bool "SD_MODE1" 164 165config NAND_MODE 166 bool "NAND_MODE" 167 168config EMMC_MODE 169 bool "EMMC_MODE" 170 171config USB_MODE 172 bool "USB" 173 174config SW_USBHOST_MODE 175 bool "SW USBHOST_MODE" 176 177config SW_SATA_MODE 178 bool "SW SATA_MODE" 179 180config SD1_LSHFT_MODE 181 bool "SD1_LSHFT_MODE" 182 183endchoice 184 185endif 186