• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1 /* SPDX-License-Identifier: GPL-2.0 */
2 /*
3  *	LiMon Monitor (LiMon) - Network.
4  *
5  *	Copyright 1994 - 2000 Neil Russell.
6  *	(See License)
7  *
8  * History
9  *	9/16/00	  bor  adapted to TQM823L/STK8xxL board, RARP/TFTP boot added
10  */
11 
12 #ifndef __NET_H__
13 #define __NET_H__
14 
15 #include <asm/cache.h>
16 #include <asm/byteorder.h>	/* for nton* / ntoh* stuff */
17 #include <env.h>
18 #include <linux/if_ether.h>
19 #include <rand.h>
20 
21 #define DEBUG_LL_STATE 0	/* Link local state machine changes */
22 #define DEBUG_DEV_PKT 0		/* Packets or info directed to the device */
23 #define DEBUG_NET_PKT 0		/* Packets on info on the network at large */
24 #define DEBUG_INT_STATE 0	/* Internal network state changes */
25 
26 /*
27  *	The number of receive packet buffers, and the required packet buffer
28  *	alignment in memory.
29  *
30  */
31 
32 #ifdef CONFIG_SYS_RX_ETH_BUFFER
33 # define PKTBUFSRX	CONFIG_SYS_RX_ETH_BUFFER
34 #else
35 # define PKTBUFSRX	4
36 #endif
37 
38 #define PKTALIGN	ARCH_DMA_MINALIGN
39 
40 /* ARP hardware address length */
41 #define ARP_HLEN 6
42 /*
43  * The size of a MAC address in string form, each digit requires two chars
44  * and five separator characters to form '00:00:00:00:00:00'.
45  */
46 #define ARP_HLEN_ASCII (ARP_HLEN * 2) + (ARP_HLEN - 1)
47 
48 /* IPv4 addresses are always 32 bits in size */
49 struct in_addr {
50 	__be32 s_addr;
51 };
52 
53 /**
54  * An incoming packet handler.
55  * @param pkt    pointer to the application packet
56  * @param dport  destination UDP port
57  * @param sip    source IP address
58  * @param sport  source UDP port
59  * @param len    packet length
60  */
61 typedef void rxhand_f(uchar *pkt, unsigned dport,
62 		      struct in_addr sip, unsigned sport,
63 		      unsigned len);
64 
65 /**
66  * An incoming ICMP packet handler.
67  * @param type	ICMP type
68  * @param code	ICMP code
69  * @param dport	destination UDP port
70  * @param sip	source IP address
71  * @param sport	source UDP port
72  * @param pkt	pointer to the ICMP packet data
73  * @param len	packet length
74  */
75 typedef void rxhand_icmp_f(unsigned type, unsigned code, unsigned dport,
76 		struct in_addr sip, unsigned sport, uchar *pkt, unsigned len);
77 
78 /*
79  *	A timeout handler.  Called after time interval has expired.
80  */
81 typedef void	thand_f(void);
82 
83 enum eth_state_t {
84 	ETH_STATE_INIT,
85 	ETH_STATE_PASSIVE,
86 	ETH_STATE_ACTIVE
87 };
88 
89 #ifdef CONFIG_DM_ETH
90 /**
91  * struct eth_pdata - Platform data for Ethernet MAC controllers
92  *
93  * @iobase: The base address of the hardware registers
94  * @enetaddr: The Ethernet MAC address that is loaded from EEPROM or env
95  * @phy_interface: PHY interface to use - see PHY_INTERFACE_MODE_...
96  * @max_speed: Maximum speed of Ethernet connection supported by MAC
97  * @priv_pdata: device specific platdata
98  */
99 struct eth_pdata {
100 	phys_addr_t iobase;
101 	unsigned char enetaddr[ARP_HLEN];
102 	int phy_interface;
103 	int max_speed;
104 	void *priv_pdata;
105 };
106 
107 enum eth_recv_flags {
108 	/*
109 	 * Check hardware device for new packets (otherwise only return those
110 	 * which are already in the memory buffer ready to process)
111 	 */
112 	ETH_RECV_CHECK_DEVICE		= 1 << 0,
113 };
114 
115 /**
116  * struct eth_ops - functions of Ethernet MAC controllers
117  *
118  * start: Prepare the hardware to send and receive packets
119  * send: Send the bytes passed in "packet" as a packet on the wire
120  * recv: Check if the hardware received a packet. If so, set the pointer to the
121  *	 packet buffer in the packetp parameter. If not, return an error or 0 to
122  *	 indicate that the hardware receive FIFO is empty. If 0 is returned, the
123  *	 network stack will not process the empty packet, but free_pkt() will be
124  *	 called if supplied
125  * free_pkt: Give the driver an opportunity to manage its packet buffer memory
126  *	     when the network stack is finished processing it. This will only be
127  *	     called when no error was returned from recv - optional
128  * stop: Stop the hardware from looking for packets - may be called even if
129  *	 state == PASSIVE
130  * mcast: Join or leave a multicast group (for TFTP) - optional
131  * write_hwaddr: Write a MAC address to the hardware (used to pass it to Linux
132  *		 on some platforms like ARM). This function expects the
133  *		 eth_pdata::enetaddr field to be populated. The method can
134  *		 return -ENOSYS to indicate that this is not implemented for
135 		 this hardware - optional.
136  * read_rom_hwaddr: Some devices have a backup of the MAC address stored in a
137  *		    ROM on the board. This is how the driver should expose it
138  *		    to the network stack. This function should fill in the
139  *		    eth_pdata::enetaddr field - optional
140  */
141 struct eth_ops {
142 	int (*start)(struct udevice *dev);
143 	int (*send)(struct udevice *dev, void *packet, int length);
144 	int (*recv)(struct udevice *dev, int flags, uchar **packetp);
145 	int (*free_pkt)(struct udevice *dev, uchar *packet, int length);
146 	void (*stop)(struct udevice *dev);
147 	int (*mcast)(struct udevice *dev, const u8 *enetaddr, int join);
148 	int (*write_hwaddr)(struct udevice *dev);
149 	int (*read_rom_hwaddr)(struct udevice *dev);
150 };
151 
152 #define eth_get_ops(dev) ((struct eth_ops *)(dev)->driver->ops)
153 
154 struct udevice *eth_get_dev(void); /* get the current device */
155 /*
156  * The devname can be either an exact name given by the driver or device tree
157  * or it can be an alias of the form "eth%d"
158  */
159 struct udevice *eth_get_dev_by_name(const char *devname);
160 unsigned char *eth_get_ethaddr(void); /* get the current device MAC */
161 
162 /* Used only when NetConsole is enabled */
163 int eth_is_active(struct udevice *dev); /* Test device for active state */
164 int eth_init_state_only(void); /* Set active state */
165 void eth_halt_state_only(void); /* Set passive state */
166 #endif
167 
168 #ifndef CONFIG_DM_ETH
169 struct eth_device {
170 #define ETH_NAME_LEN 20
171 	char name[ETH_NAME_LEN];
172 	unsigned char enetaddr[ARP_HLEN];
173 	phys_addr_t iobase;
174 	int state;
175 
176 	int (*init)(struct eth_device *, bd_t *);
177 	int (*send)(struct eth_device *, void *packet, int length);
178 	int (*recv)(struct eth_device *);
179 	void (*halt)(struct eth_device *);
180 	int (*mcast)(struct eth_device *, const u8 *enetaddr, int join);
181 	int (*write_hwaddr)(struct eth_device *);
182 	struct eth_device *next;
183 	int index;
184 	void *priv;
185 };
186 
187 int eth_register(struct eth_device *dev);/* Register network device */
188 int eth_unregister(struct eth_device *dev);/* Remove network device */
189 
190 extern struct eth_device *eth_current;
191 
eth_get_dev(void)192 static __always_inline struct eth_device *eth_get_dev(void)
193 {
194 	return eth_current;
195 }
196 struct eth_device *eth_get_dev_by_name(const char *devname);
197 struct eth_device *eth_get_dev_by_index(int index); /* get dev @ index */
198 
199 /* get the current device MAC */
eth_get_ethaddr(void)200 static inline unsigned char *eth_get_ethaddr(void)
201 {
202 	if (eth_current)
203 		return eth_current->enetaddr;
204 	return NULL;
205 }
206 
207 /* Used only when NetConsole is enabled */
208 int eth_is_active(struct eth_device *dev); /* Test device for active state */
209 /* Set active state */
eth_init_state_only(void)210 static __always_inline int eth_init_state_only(void)
211 {
212 	eth_get_dev()->state = ETH_STATE_ACTIVE;
213 
214 	return 0;
215 }
216 /* Set passive state */
eth_halt_state_only(void)217 static __always_inline void eth_halt_state_only(void)
218 {
219 	eth_get_dev()->state = ETH_STATE_PASSIVE;
220 }
221 
222 /*
223  * Set the hardware address for an ethernet interface based on 'eth%daddr'
224  * environment variable (or just 'ethaddr' if eth_number is 0).
225  * Args:
226  *	base_name - base name for device (normally "eth")
227  *	eth_number - value of %d (0 for first device of this type)
228  * Returns:
229  *	0 is success, non-zero is error status from driver.
230  */
231 int eth_write_hwaddr(struct eth_device *dev, const char *base_name,
232 		     int eth_number);
233 
234 int usb_eth_initialize(bd_t *bi);
235 #endif
236 
237 int eth_initialize(void);		/* Initialize network subsystem */
238 void eth_try_another(int first_restart);	/* Change the device */
239 void eth_set_current(void);		/* set nterface to ethcur var */
240 
241 int eth_get_dev_index(void);		/* get the device index */
242 
243 /**
244  * eth_env_set_enetaddr_by_index() - set the MAC address environment variable
245  *
246  * This sets up an environment variable with the given MAC address (@enetaddr).
247  * The environment variable to be set is defined by <@base_name><@index>addr.
248  * If @index is 0 it is omitted. For common Ethernet this means ethaddr,
249  * eth1addr, etc.
250  *
251  * @base_name:  Base name for variable, typically "eth"
252  * @index:      Index of interface being updated (>=0)
253  * @enetaddr:   Pointer to MAC address to put into the variable
254  * @return 0 if OK, other value on error
255  */
256 int eth_env_set_enetaddr_by_index(const char *base_name, int index,
257 				 uchar *enetaddr);
258 
259 
260 /*
261  * Initialize USB ethernet device with CONFIG_DM_ETH
262  * Returns:
263  *	0 is success, non-zero is error status.
264  */
265 int usb_ether_init(void);
266 
267 /*
268  * Get the hardware address for an ethernet interface .
269  * Args:
270  *	base_name - base name for device (normally "eth")
271  *	index - device index number (0 for first)
272  *	enetaddr - returns 6 byte hardware address
273  * Returns:
274  *	Return true if the address is valid.
275  */
276 int eth_env_get_enetaddr_by_index(const char *base_name, int index,
277 				 uchar *enetaddr);
278 
279 int eth_init(void);			/* Initialize the device */
280 int eth_send(void *packet, int length);	   /* Send a packet */
281 
282 #if defined(CONFIG_API) || defined(CONFIG_EFI_LOADER)
283 int eth_receive(void *packet, int length); /* Receive a packet*/
284 extern void (*push_packet)(void *packet, int length);
285 #endif
286 int eth_rx(void);			/* Check for received packets */
287 void eth_halt(void);			/* stop SCC */
288 const char *eth_get_name(void);		/* get name of current device */
289 int eth_mcast_join(struct in_addr mcast_addr, int join);
290 
291 /**********************************************************************/
292 /*
293  *	Protocol headers.
294  */
295 
296 /*
297  *	Ethernet header
298  */
299 
300 struct ethernet_hdr {
301 	u8		et_dest[ARP_HLEN];	/* Destination node	*/
302 	u8		et_src[ARP_HLEN];	/* Source node		*/
303 	u16		et_protlen;		/* Protocol or length	*/
304 } __attribute__((packed));
305 
306 /* Ethernet header size */
307 #define ETHER_HDR_SIZE	(sizeof(struct ethernet_hdr))
308 
309 #define ETH_FCS_LEN	4		/* Octets in the FCS		*/
310 
311 struct e802_hdr {
312 	u8		et_dest[ARP_HLEN];	/* Destination node	*/
313 	u8		et_src[ARP_HLEN];	/* Source node		*/
314 	u16		et_protlen;		/* Protocol or length	*/
315 	u8		et_dsap;		/* 802 DSAP		*/
316 	u8		et_ssap;		/* 802 SSAP		*/
317 	u8		et_ctl;			/* 802 control		*/
318 	u8		et_snap1;		/* SNAP			*/
319 	u8		et_snap2;
320 	u8		et_snap3;
321 	u16		et_prot;		/* 802 protocol		*/
322 } __attribute__((packed));
323 
324 /* 802 + SNAP + ethernet header size */
325 #define E802_HDR_SIZE	(sizeof(struct e802_hdr))
326 
327 /*
328  *	Virtual LAN Ethernet header
329  */
330 struct vlan_ethernet_hdr {
331 	u8		vet_dest[ARP_HLEN];	/* Destination node	*/
332 	u8		vet_src[ARP_HLEN];	/* Source node		*/
333 	u16		vet_vlan_type;		/* PROT_VLAN		*/
334 	u16		vet_tag;		/* TAG of VLAN		*/
335 	u16		vet_type;		/* protocol type	*/
336 } __attribute__((packed));
337 
338 /* VLAN Ethernet header size */
339 #define VLAN_ETHER_HDR_SIZE	(sizeof(struct vlan_ethernet_hdr))
340 
341 #define PROT_IP		0x0800		/* IP protocol			*/
342 #define PROT_ARP	0x0806		/* IP ARP protocol		*/
343 #define PROT_WOL	0x0842		/* ether-wake WoL protocol	*/
344 #define PROT_RARP	0x8035		/* IP ARP protocol		*/
345 #define PROT_VLAN	0x8100		/* IEEE 802.1q protocol		*/
346 #define PROT_IPV6	0x86dd		/* IPv6 over bluebook		*/
347 #define PROT_PPP_SES	0x8864		/* PPPoE session messages	*/
348 
349 #define IPPROTO_ICMP	 1	/* Internet Control Message Protocol	*/
350 #define IPPROTO_UDP	17	/* User Datagram Protocol		*/
351 
352 /*
353  *	Internet Protocol (IP) header.
354  */
355 struct ip_hdr {
356 	u8		ip_hl_v;	/* header length and version	*/
357 	u8		ip_tos;		/* type of service		*/
358 	u16		ip_len;		/* total length			*/
359 	u16		ip_id;		/* identification		*/
360 	u16		ip_off;		/* fragment offset field	*/
361 	u8		ip_ttl;		/* time to live			*/
362 	u8		ip_p;		/* protocol			*/
363 	u16		ip_sum;		/* checksum			*/
364 	struct in_addr	ip_src;		/* Source IP address		*/
365 	struct in_addr	ip_dst;		/* Destination IP address	*/
366 } __attribute__((packed));
367 
368 #define IP_OFFS		0x1fff /* ip offset *= 8 */
369 #define IP_FLAGS	0xe000 /* first 3 bits */
370 #define IP_FLAGS_RES	0x8000 /* reserved */
371 #define IP_FLAGS_DFRAG	0x4000 /* don't fragments */
372 #define IP_FLAGS_MFRAG	0x2000 /* more fragments */
373 
374 #define IP_HDR_SIZE		(sizeof(struct ip_hdr))
375 
376 /*
377  *	Internet Protocol (IP) + UDP header.
378  */
379 struct ip_udp_hdr {
380 	u8		ip_hl_v;	/* header length and version	*/
381 	u8		ip_tos;		/* type of service		*/
382 	u16		ip_len;		/* total length			*/
383 	u16		ip_id;		/* identification		*/
384 	u16		ip_off;		/* fragment offset field	*/
385 	u8		ip_ttl;		/* time to live			*/
386 	u8		ip_p;		/* protocol			*/
387 	u16		ip_sum;		/* checksum			*/
388 	struct in_addr	ip_src;		/* Source IP address		*/
389 	struct in_addr	ip_dst;		/* Destination IP address	*/
390 	u16		udp_src;	/* UDP source port		*/
391 	u16		udp_dst;	/* UDP destination port		*/
392 	u16		udp_len;	/* Length of UDP packet		*/
393 	u16		udp_xsum;	/* Checksum			*/
394 } __attribute__((packed));
395 
396 #define IP_UDP_HDR_SIZE		(sizeof(struct ip_udp_hdr))
397 #define UDP_HDR_SIZE		(IP_UDP_HDR_SIZE - IP_HDR_SIZE)
398 
399 /*
400  *	Address Resolution Protocol (ARP) header.
401  */
402 struct arp_hdr {
403 	u16		ar_hrd;		/* Format of hardware address	*/
404 #   define ARP_ETHER	    1		/* Ethernet  hardware address	*/
405 	u16		ar_pro;		/* Format of protocol address	*/
406 	u8		ar_hln;		/* Length of hardware address	*/
407 	u8		ar_pln;		/* Length of protocol address	*/
408 #   define ARP_PLEN	4
409 	u16		ar_op;		/* Operation			*/
410 #   define ARPOP_REQUEST    1		/* Request  to resolve  address	*/
411 #   define ARPOP_REPLY	    2		/* Response to previous request	*/
412 
413 #   define RARPOP_REQUEST   3		/* Request  to resolve  address	*/
414 #   define RARPOP_REPLY	    4		/* Response to previous request */
415 
416 	/*
417 	 * The remaining fields are variable in size, according to
418 	 * the sizes above, and are defined as appropriate for
419 	 * specific hardware/protocol combinations.
420 	 */
421 	u8		ar_data[0];
422 #define ar_sha		ar_data[0]
423 #define ar_spa		ar_data[ARP_HLEN]
424 #define ar_tha		ar_data[ARP_HLEN + ARP_PLEN]
425 #define ar_tpa		ar_data[ARP_HLEN + ARP_PLEN + ARP_HLEN]
426 #if 0
427 	u8		ar_sha[];	/* Sender hardware address	*/
428 	u8		ar_spa[];	/* Sender protocol address	*/
429 	u8		ar_tha[];	/* Target hardware address	*/
430 	u8		ar_tpa[];	/* Target protocol address	*/
431 #endif /* 0 */
432 } __attribute__((packed));
433 
434 #define ARP_HDR_SIZE	(8+20)		/* Size assuming ethernet	*/
435 
436 /*
437  * ICMP stuff (just enough to handle (host) redirect messages)
438  */
439 #define ICMP_ECHO_REPLY		0	/* Echo reply			*/
440 #define ICMP_NOT_REACH		3	/* Detination unreachable	*/
441 #define ICMP_REDIRECT		5	/* Redirect (change route)	*/
442 #define ICMP_ECHO_REQUEST	8	/* Echo request			*/
443 
444 /* Codes for REDIRECT. */
445 #define ICMP_REDIR_NET		0	/* Redirect Net			*/
446 #define ICMP_REDIR_HOST		1	/* Redirect Host		*/
447 
448 /* Codes for NOT_REACH */
449 #define ICMP_NOT_REACH_PORT	3	/* Port unreachable		*/
450 
451 struct icmp_hdr {
452 	u8		type;
453 	u8		code;
454 	u16		checksum;
455 	union {
456 		struct {
457 			u16	id;
458 			u16	sequence;
459 		} echo;
460 		u32	gateway;
461 		struct {
462 			u16	unused;
463 			u16	mtu;
464 		} frag;
465 		u8 data[0];
466 	} un;
467 } __attribute__((packed));
468 
469 #define ICMP_HDR_SIZE		(sizeof(struct icmp_hdr))
470 #define IP_ICMP_HDR_SIZE	(IP_HDR_SIZE + ICMP_HDR_SIZE)
471 
472 /*
473  * Maximum packet size; used to allocate packet storage. Use
474  * the maxium Ethernet frame size as specified by the Ethernet
475  * standard including the 802.1Q tag (VLAN tagging).
476  * maximum packet size =  1522
477  * maximum packet size and multiple of 32 bytes =  1536
478  */
479 #define PKTSIZE			1522
480 #define PKTSIZE_ALIGN		1536
481 
482 /*
483  * Maximum receive ring size; that is, the number of packets
484  * we can buffer before overflow happens. Basically, this just
485  * needs to be enough to prevent a packet being discarded while
486  * we are processing the previous one.
487  */
488 #define RINGSZ		4
489 #define RINGSZ_LOG2	2
490 
491 /**********************************************************************/
492 /*
493  *	Globals.
494  *
495  * Note:
496  *
497  * All variables of type struct in_addr are stored in NETWORK byte order
498  * (big endian).
499  */
500 
501 /* net.c */
502 /** BOOTP EXTENTIONS **/
503 extern struct in_addr net_gateway;	/* Our gateway IP address */
504 extern struct in_addr net_netmask;	/* Our subnet mask (0 = unknown) */
505 /* Our Domain Name Server (0 = unknown) */
506 extern struct in_addr net_dns_server;
507 #if defined(CONFIG_BOOTP_DNS2)
508 /* Our 2nd Domain Name Server (0 = unknown) */
509 extern struct in_addr net_dns_server2;
510 #endif
511 extern char	net_nis_domain[32];	/* Our IS domain */
512 extern char	net_hostname[32];	/* Our hostname */
513 extern char	net_root_path[64];	/* Our root path */
514 /** END OF BOOTP EXTENTIONS **/
515 extern u8		net_ethaddr[ARP_HLEN];		/* Our ethernet address */
516 extern u8		net_server_ethaddr[ARP_HLEN];	/* Boot server enet address */
517 extern struct in_addr	net_ip;		/* Our    IP addr (0 = unknown) */
518 extern struct in_addr	net_server_ip;	/* Server IP addr (0 = unknown) */
519 extern uchar		*net_tx_packet;		/* THE transmit packet */
520 extern uchar		*net_rx_packets[PKTBUFSRX]; /* Receive packets */
521 extern uchar		*net_rx_packet;		/* Current receive packet */
522 extern int		net_rx_packet_len;	/* Current rx packet length */
523 extern const u8		net_bcast_ethaddr[ARP_HLEN];	/* Ethernet broadcast address */
524 extern const u8		net_null_ethaddr[ARP_HLEN];
525 
526 #define VLAN_NONE	4095			/* untagged */
527 #define VLAN_IDMASK	0x0fff			/* mask of valid vlan id */
528 extern ushort		net_our_vlan;		/* Our VLAN */
529 extern ushort		net_native_vlan;	/* Our Native VLAN */
530 
531 extern int		net_restart_wrap;	/* Tried all network devices */
532 
533 enum proto_t {
534 	BOOTP, RARP, ARP, TFTPGET, DHCP, PING, DNS, NFS, CDP, NETCONS, SNTP,
535 	TFTPSRV, TFTPPUT, LINKLOCAL, FASTBOOT, WOL
536 };
537 
538 extern char	net_boot_file_name[1024];/* Boot File name */
539 /* Indicates whether the file name was specified on the command line */
540 extern bool	net_boot_file_name_explicit;
541 /* The actual transferred size of the bootfile (in bytes) */
542 extern u32	net_boot_file_size;
543 /* Boot file size in blocks as reported by the DHCP server */
544 extern u32	net_boot_file_expected_size_in_blocks;
545 
546 #if defined(CONFIG_CMD_DNS)
547 extern char *net_dns_resolve;		/* The host to resolve  */
548 extern char *net_dns_env_var;		/* the env var to put the ip into */
549 #endif
550 
551 #if defined(CONFIG_CMD_PING)
552 extern struct in_addr net_ping_ip;	/* the ip address to ping */
553 #endif
554 
555 #if defined(CONFIG_CMD_CDP)
556 /* when CDP completes these hold the return values */
557 extern ushort cdp_native_vlan;		/* CDP returned native VLAN */
558 extern ushort cdp_appliance_vlan;	/* CDP returned appliance VLAN */
559 
560 /*
561  * Check for a CDP packet by examining the received MAC address field
562  */
is_cdp_packet(const uchar * ethaddr)563 static inline int is_cdp_packet(const uchar *ethaddr)
564 {
565 	extern const u8 net_cdp_ethaddr[ARP_HLEN];
566 
567 	return memcmp(ethaddr, net_cdp_ethaddr, ARP_HLEN) == 0;
568 }
569 #endif
570 
571 #if defined(CONFIG_CMD_SNTP)
572 extern struct in_addr	net_ntp_server;		/* the ip address to NTP */
573 extern int net_ntp_time_offset;			/* offset time from UTC */
574 #endif
575 
576 /* Initialize the network adapter */
577 void net_init(void);
578 int net_loop(enum proto_t);
579 
580 /* Load failed.	 Start again. */
581 int net_start_again(void);
582 
583 /* Get size of the ethernet header when we send */
584 int net_eth_hdr_size(void);
585 
586 /* Set ethernet header; returns the size of the header */
587 int net_set_ether(uchar *xet, const uchar *dest_ethaddr, uint prot);
588 int net_update_ether(struct ethernet_hdr *et, uchar *addr, uint prot);
589 
590 /* Set IP header */
591 void net_set_ip_header(uchar *pkt, struct in_addr dest, struct in_addr source,
592 		       u16 pkt_len, u8 proto);
593 void net_set_udp_header(uchar *pkt, struct in_addr dest, int dport,
594 				int sport, int len);
595 
596 /**
597  * compute_ip_checksum() - Compute IP checksum
598  *
599  * @addr:	Address to check (must be 16-bit aligned)
600  * @nbytes:	Number of bytes to check (normally a multiple of 2)
601  * @return 16-bit IP checksum
602  */
603 unsigned compute_ip_checksum(const void *addr, unsigned nbytes);
604 
605 /**
606  * add_ip_checksums() - add two IP checksums
607  *
608  * @offset:	Offset of first sum (if odd we do a byte-swap)
609  * @sum:	First checksum
610  * @new_sum:	New checksum to add
611  * @return updated 16-bit IP checksum
612  */
613 unsigned add_ip_checksums(unsigned offset, unsigned sum, unsigned new_sum);
614 
615 /**
616  * ip_checksum_ok() - check if a checksum is correct
617  *
618  * This works by making sure the checksum sums to 0
619  *
620  * @addr:	Address to check (must be 16-bit aligned)
621  * @nbytes:	Number of bytes to check (normally a multiple of 2)
622  * @return true if the checksum matches, false if not
623  */
624 int ip_checksum_ok(const void *addr, unsigned nbytes);
625 
626 /* Callbacks */
627 rxhand_f *net_get_udp_handler(void);	/* Get UDP RX packet handler */
628 void net_set_udp_handler(rxhand_f *);	/* Set UDP RX packet handler */
629 rxhand_f *net_get_arp_handler(void);	/* Get ARP RX packet handler */
630 void net_set_arp_handler(rxhand_f *);	/* Set ARP RX packet handler */
631 bool arp_is_waiting(void);		/* Waiting for ARP reply? */
632 void net_set_icmp_handler(rxhand_icmp_f *f); /* Set ICMP RX handler */
633 void net_set_timeout_handler(ulong, thand_f *);/* Set timeout handler */
634 
635 /* Network loop state */
636 enum net_loop_state {
637 	NETLOOP_CONTINUE,
638 	NETLOOP_RESTART,
639 	NETLOOP_SUCCESS,
640 	NETLOOP_FAIL
641 };
642 extern enum net_loop_state net_state;
643 
net_set_state(enum net_loop_state state)644 static inline void net_set_state(enum net_loop_state state)
645 {
646 	debug_cond(DEBUG_INT_STATE, "--- NetState set to %d\n", state);
647 	net_state = state;
648 }
649 
650 /*
651  * net_get_async_tx_pkt_buf - Get a packet buffer that is not in use for
652  *			      sending an asynchronous reply
653  *
654  * returns - ptr to packet buffer
655  */
656 uchar * net_get_async_tx_pkt_buf(void);
657 
658 /* Transmit a packet */
net_send_packet(uchar * pkt,int len)659 static inline void net_send_packet(uchar *pkt, int len)
660 {
661 	/* Currently no way to return errors from eth_send() */
662 	(void) eth_send(pkt, len);
663 }
664 
665 /*
666  * Transmit "net_tx_packet" as UDP packet, performing ARP request if needed
667  *  (ether will be populated)
668  *
669  * @param ether Raw packet buffer
670  * @param dest IP address to send the datagram to
671  * @param dport Destination UDP port
672  * @param sport Source UDP port
673  * @param payload_len Length of data after the UDP header
674  */
675 int net_send_ip_packet(uchar *ether, struct in_addr dest, int dport, int sport,
676 		       int payload_len, int proto, u8 action, u32 tcp_seq_num,
677 		       u32 tcp_ack_num);
678 int net_send_udp_packet(uchar *ether, struct in_addr dest, int dport,
679 			int sport, int payload_len);
680 
681 /* Processes a received packet */
682 void net_process_received_packet(uchar *in_packet, int len);
683 
684 #if defined(CONFIG_NETCONSOLE) && !defined(CONFIG_SPL_BUILD)
685 void nc_start(void);
686 int nc_input_packet(uchar *pkt, struct in_addr src_ip, unsigned dest_port,
687 	unsigned src_port, unsigned len);
688 #endif
689 
eth_is_on_demand_init(void)690 static __always_inline int eth_is_on_demand_init(void)
691 {
692 #if defined(CONFIG_NETCONSOLE) && !defined(CONFIG_SPL_BUILD)
693 	extern enum proto_t net_loop_last_protocol;
694 
695 	return net_loop_last_protocol != NETCONS;
696 #else
697 	return 1;
698 #endif
699 }
700 
eth_set_last_protocol(int protocol)701 static inline void eth_set_last_protocol(int protocol)
702 {
703 #if defined(CONFIG_NETCONSOLE) && !defined(CONFIG_SPL_BUILD)
704 	extern enum proto_t net_loop_last_protocol;
705 
706 	net_loop_last_protocol = protocol;
707 #endif
708 }
709 
710 /*
711  * Check if autoload is enabled. If so, use either NFS or TFTP to download
712  * the boot file.
713  */
714 void net_auto_load(void);
715 
716 /*
717  * The following functions are a bit ugly, but necessary to deal with
718  * alignment restrictions on ARM.
719  *
720  * We're using inline functions, which had the smallest memory
721  * footprint in our tests.
722  */
723 /* return IP *in network byteorder* */
net_read_ip(void * from)724 static inline struct in_addr net_read_ip(void *from)
725 {
726 	struct in_addr ip;
727 
728 	memcpy((void *)&ip, (void *)from, sizeof(ip));
729 	return ip;
730 }
731 
732 /* return ulong *in network byteorder* */
net_read_u32(void * from)733 static inline u32 net_read_u32(void *from)
734 {
735 	u32 l;
736 
737 	memcpy((void *)&l, (void *)from, sizeof(l));
738 	return l;
739 }
740 
741 /* write IP *in network byteorder* */
net_write_ip(void * to,struct in_addr ip)742 static inline void net_write_ip(void *to, struct in_addr ip)
743 {
744 	memcpy(to, (void *)&ip, sizeof(ip));
745 }
746 
747 /* copy IP */
net_copy_ip(void * to,void * from)748 static inline void net_copy_ip(void *to, void *from)
749 {
750 	memcpy((void *)to, from, sizeof(struct in_addr));
751 }
752 
753 /* copy ulong */
net_copy_u32(void * to,void * from)754 static inline void net_copy_u32(void *to, void *from)
755 {
756 	memcpy((void *)to, (void *)from, sizeof(u32));
757 }
758 
759 /**
760  * is_zero_ethaddr - Determine if give Ethernet address is all zeros.
761  * @addr: Pointer to a six-byte array containing the Ethernet address
762  *
763  * Return true if the address is all zeroes.
764  */
is_zero_ethaddr(const u8 * addr)765 static inline int is_zero_ethaddr(const u8 *addr)
766 {
767 	return !(addr[0] | addr[1] | addr[2] | addr[3] | addr[4] | addr[5]);
768 }
769 
770 /**
771  * is_multicast_ethaddr - Determine if the Ethernet address is a multicast.
772  * @addr: Pointer to a six-byte array containing the Ethernet address
773  *
774  * Return true if the address is a multicast address.
775  * By definition the broadcast address is also a multicast address.
776  */
is_multicast_ethaddr(const u8 * addr)777 static inline int is_multicast_ethaddr(const u8 *addr)
778 {
779 	return 0x01 & addr[0];
780 }
781 
782 /*
783  * is_broadcast_ethaddr - Determine if the Ethernet address is broadcast
784  * @addr: Pointer to a six-byte array containing the Ethernet address
785  *
786  * Return true if the address is the broadcast address.
787  */
is_broadcast_ethaddr(const u8 * addr)788 static inline int is_broadcast_ethaddr(const u8 *addr)
789 {
790 	return (addr[0] & addr[1] & addr[2] & addr[3] & addr[4] & addr[5]) ==
791 		0xff;
792 }
793 
794 /*
795  * is_valid_ethaddr - Determine if the given Ethernet address is valid
796  * @addr: Pointer to a six-byte array containing the Ethernet address
797  *
798  * Check that the Ethernet address (MAC) is not 00:00:00:00:00:00, is not
799  * a multicast address, and is not FF:FF:FF:FF:FF:FF.
800  *
801  * Return true if the address is valid.
802  */
is_valid_ethaddr(const u8 * addr)803 static inline int is_valid_ethaddr(const u8 *addr)
804 {
805 	/* FF:FF:FF:FF:FF:FF is a multicast address so we don't need to
806 	 * explicitly check for it here. */
807 	return !is_multicast_ethaddr(addr) && !is_zero_ethaddr(addr);
808 }
809 
810 /**
811  * net_random_ethaddr - Generate software assigned random Ethernet address
812  * @addr: Pointer to a six-byte array containing the Ethernet address
813  *
814  * Generate a random Ethernet address (MAC) that is not multicast
815  * and has the local assigned bit set.
816  */
net_random_ethaddr(uchar * addr)817 static inline void net_random_ethaddr(uchar *addr)
818 {
819 	int i;
820 	unsigned int seed = get_ticks();
821 
822 	for (i = 0; i < 6; i++)
823 		addr[i] = rand_r(&seed);
824 
825 	addr[0] &= 0xfe;	/* clear multicast bit */
826 	addr[0] |= 0x02;	/* set local assignment bit (IEEE802) */
827 }
828 
829 /**
830  * string_to_enetaddr() - Parse a MAC address
831  *
832  * Convert a string MAC address
833  *
834  * Implemented in lib/net_utils.c (built unconditionally)
835  *
836  * @addr: MAC address in aa:bb:cc:dd:ee:ff format, where each part is a 2-digit
837  *	hex value
838  * @enetaddr: Place to put MAC address (6 bytes)
839  */
840 void string_to_enetaddr(const char *addr, uint8_t *enetaddr);
841 
842 /* Convert an IP address to a string */
843 void ip_to_string(struct in_addr x, char *s);
844 
845 /**
846  * string_to_ip() - Convert a string to ip address
847  *
848  * Implemented in lib/net_utils.c (built unconditionally)
849  *
850  * @s: Input string to parse
851  * @return: in_addr struct containing the parsed IP address
852  */
853 struct in_addr string_to_ip(const char *s);
854 
855 /* Convert a VLAN id to a string */
856 void vlan_to_string(ushort x, char *s);
857 
858 /* Convert a string to a vlan id */
859 ushort string_to_vlan(const char *s);
860 
861 /* read a VLAN id from an environment variable */
862 ushort env_get_vlan(char *);
863 
864 /* copy a filename (allow for "..." notation, limit length) */
865 void copy_filename(char *dst, const char *src, int size);
866 
867 /* check if serverip is specified in filename from the command line */
868 int is_serverip_in_cmd(void);
869 
870 /**
871  * net_parse_bootfile - Parse the bootfile env var / cmd line param
872  *
873  * @param ipaddr - a pointer to the ipaddr to populate if included in bootfile
874  * @param filename - a pointer to the string to save the filename part
875  * @param max_len - The longest - 1 that the filename part can be
876  *
877  * return 1 if parsed, 0 if bootfile is empty
878  */
879 int net_parse_bootfile(struct in_addr *ipaddr, char *filename, int max_len);
880 
881 /* get a random source port */
882 unsigned int random_port(void);
883 
884 /**
885  * update_tftp - Update firmware over TFTP (via DFU)
886  *
887  * This function updates board's firmware via TFTP
888  *
889  * @param addr - memory address where data is stored
890  * @param interface - the DFU medium name - e.g. "mmc"
891  * @param devstring - the DFU medium number - e.g. "1"
892  *
893  * @return - 0 on success, other value on failure
894  */
895 int update_tftp(ulong addr, char *interface, char *devstring);
896 
897 /**
898  * env_get_ip() - Convert an environment value to to an ip address
899  *
900  * @var: Environment variable to convert. The value of this variable must be
901  *	in the format format a.b.c.d, where each value is a decimal number from
902  *	0 to 255
903  * @return IP address, or 0 if invalid
904  */
env_get_ip(char * var)905 static inline struct in_addr env_get_ip(char *var)
906 {
907 	return string_to_ip(env_get(var));
908 }
909 #endif /* __NET_H__ */
910