| /external/u-boot/board/freescale/p1010rdb/ |
| D | README.P1010RDB-PB | 66 SW3[1:8]= 10010000
73 SW4[1:4]= 1111 and SW3[3:4]= 00 for 16bit NOR boot
74 SW4[1:4]= 1010 and SW3[3:4]= 01 for 8bit NAND boot
75 SW4[1:4]= 0110 and SW3[3:4]= 00 for SPI boot
76 SW4[1:4]= 0111 and SW3[3:4]= 10 for SD boot
153 set SW1[8]=0, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
157 set SW1[8]=1, SW4[1:4]= 1111 and SW3[3:4]= 00, then power on the board
162 Set SW4[1:4]= 1010 and SW3[3:4]= 01, then power on the board
168 set SW4[1:4]= 0110 and SW3[3:4]= 00, then power on the board
175 set SW4[1:4]= 0111 and SW3[3:4]= 10, then power on the board
|
| /external/u-boot/board/freescale/ls1088a/ |
| D | README | 18 SW3 1111 0010
25 SW3 1111 0010
32 SW3 1111 0010
91 SW3 to SW12 are identical for all boot source
93 SW3 0010 0100
|
| /external/u-boot/doc/ |
| D | README.mpc85xxcds | 134 SW3=11101111
142 frequency can be changed by setting SW3:
146 SW3=XX00XXXX == CORE:CCB 2:1
159 SW3=00001000
173 SW3=11001000 (8X) (2:1)
176 SW3=X000XXXX == CORE:CCB 4:1
|
| /external/u-boot/board/freescale/t102xrdb/ |
| D | README | 194 set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
196 set SW1[1:8] = '00010111', SW2[1] = '1', SW3[4] = '0' for NOR boot
202 via DIP-switch: set SW3[5:7] = '100'
205 via DIP-switch: set SW3[5:7] = '100'
210 via DIP-Switch: set SW3[5:7] = '000'
213 via DIP-switch: set SW3[5:7] = '000'
223 set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot
250 SW3[3] = '1' for SD card(or 'switch sd' by software)
251 SW3[3] = '0' for eMMC (or 'switch emmc' by software)
|
| /external/u-boot/board/freescale/ls1028a/ |
| D | README | 15 SW3: 1111_0000
20 SW3: 1111_0000
25 SW3: 1111_0000
86 SW3 : 0000_0010
98 SW3 : 0000_0010
|
| /external/u-boot/board/freescale/t104xrdb/ |
| D | README | 288 SW3: 11100001
293 SW3: 11110001
298 SW3: 11100001
303 SW3: 11100001
310 SW3: 11100001
315 SW3: 11110001
320 SW3: 11100001
325 SW3: 11100001
|
| /external/u-boot/board/sbc8548/ |
| D | README | 216 SW3.1 CFG_HOST_AGT0 1* 0
217 SW3.2 CFG_HOST_AGT1 1* 0
218 SW3.3 CFG_HOST_AGT2 1* 0
219 SW3.4 CFG_IO_PORTS0 1* 0
220 SW3.5 CFG_IO_PORTS0 1 0*
221 SW3.6 CFG_IO_PORTS0 1 0*
|
| /external/u-boot/board/freescale/t208xrdb/ |
| D | README | 143 SW3[1:8] = '11100001'
154 set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
159 via DIP-switch: set SW3[5:7] = '100'
163 via DIP-Switch: set SW3[5:7] = '000'
173 set SW1[1:8] = '10000010', SW2[1] = '1', SW3[4] = '1' for NAND boot
|
| /external/u-boot/board/phytec/pfla02/ |
| D | README | 21 The dip switch "SW3" on the board let choose the boot device.
|
| /external/u-boot/doc/board/freescale/ |
| D | b4860qds.rst | 143 SW3 OFF OFF OFF ON OFF OFF ON OFF
158 SW3 [1:4] = 0001
164 SW3 [1:4] = 1000
176 SW3 OFF OFF OFF ON OFF OFF ON OFF
191 SW3 [1:4] = 0001
197 SW3 [1:4] = 1000
|
| /external/u-boot/include/power/ |
| D | mc34vr500_pmic.h | 167 SW3, enumerator
|
| /external/u-boot/board/freescale/mpc832xemds/ |
| D | README | 17 SW3 is switch 18 as silk-screened onto the board.
28 SW3[1-8]= 0000_1000 (core PLL setting, core enable)
|
| /external/webp/src/dsp/ |
| D | rescaler_msa.c | 143 SW3(val0_m, val1_m, val2_m, dst, 4); in ExportRowExpand_0()
210 SW3(val0_m, val1_m, val2_m, dst, 4); in ExportRowExpand_1()
305 SW3(val0_m, val1_m, val2_m, dst, 4);
378 SW3(val0_m, val1_m, val2_m, dst, 4);
|
| /external/u-boot/arch/arm/dts/ |
| D | imx7ulp-evk.dts | 107 sw3_reg: SW3 {
108 regulator-name = "SW3";
|
| D | armada-7040-db.dts | 45 * Boot device: SPI NOR, 0x32 (SW3)
|
| D | armada-7040-db-nand.dts | 45 * Boot device: NAND, 0xE (SW3)
|
| D | ulcb.dtsi | 58 label = "SW3";
|
| D | r8a7794-silk.dts | 52 label = "SW3";
|
| D | armada-388-clearfog.dts | 152 /* The rear SW3 button */
|
| /external/u-boot/board/freescale/mpc8641hpcn/ |
| D | README | 43 SW3(1-7) = 0011000 CONFIG_SYS_VID = 0011000 :: VCORE = 1.2V
45 SW3(8) = 0 VCC_PLAT = 0 :: VCC_PLAT = 1.2V
|
| /external/python/cpython2/Lib/plat-irix5/ |
| D | DEVICE.py | 197 SW3 = 114 variable
|
| /external/python/cpython2/Lib/plat-irix6/ |
| D | DEVICE.py | 197 SW3 = 114 variable
|
| /external/u-boot/board/freescale/mpc837xemds/ |
| D | README | 26 SW3[1-8]= 0011_0000 (BOOTSEQ, ROMLOC setting)
|
| /external/u-boot/board/freescale/mpc8536ds/ |
| D | README | 71 SW3[1] = 0
|
| /external/u-boot/board/ti/ks2_evm/ |
| D | README | 189 1. Set the SW3 dip switch to "ARM MMC Boot mode" as per instruction at
|