/* * Copyright © 2010 Intel Corporation * * Permission is hereby granted, free of charge, to any person obtaining a * copy of this software and associated documentation files (the "Software"), * to deal in the Software without restriction, including without limitation * the rights to use, copy, modify, merge, publish, distribute, sublicense, * and/or sell copies of the Software, and to permit persons to whom the * Software is furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice (including the next * paragraph) shall be included in all copies or substantial portions of the * Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS * IN THE SOFTWARE. */ #include "brw_context.h" #include "brw_defines.h" #include "brw_state.h" #include "intel_batchbuffer.h" #include "intel_fbo.h" /** * Emit a PIPE_CONTROL with various flushing flags. * * The caller is responsible for deciding what flags are appropriate for the * given generation. */ void brw_emit_pipe_control_flush(struct brw_context *brw, uint32_t flags) { const struct gen_device_info *devinfo = &brw->screen->devinfo; if (devinfo->gen >= 6 && (flags & PIPE_CONTROL_CACHE_FLUSH_BITS) && (flags & PIPE_CONTROL_CACHE_INVALIDATE_BITS)) { /* A pipe control command with flush and invalidate bits set * simultaneously is an inherently racy operation on Gen6+ if the * contents of the flushed caches were intended to become visible from * any of the invalidated caches. Split it in two PIPE_CONTROLs, the * first one should stall the pipeline to make sure that the flushed R/W * caches are coherent with memory once the specified R/O caches are * invalidated. On pre-Gen6 hardware the (implicit) R/O cache * invalidation seems to happen at the bottom of the pipeline together * with any write cache flush, so this shouldn't be a concern. In order * to ensure a full stall, we do an end-of-pipe sync. */ brw_emit_end_of_pipe_sync(brw, (flags & PIPE_CONTROL_CACHE_FLUSH_BITS)); flags &= ~(PIPE_CONTROL_CACHE_FLUSH_BITS | PIPE_CONTROL_CS_STALL); } brw->vtbl.emit_raw_pipe_control(brw, flags, NULL, 0, 0); } /** * Emit a PIPE_CONTROL that writes to a buffer object. * * \p flags should contain one of the following items: * - PIPE_CONTROL_WRITE_IMMEDIATE * - PIPE_CONTROL_WRITE_TIMESTAMP * - PIPE_CONTROL_WRITE_DEPTH_COUNT */ void brw_emit_pipe_control_write(struct brw_context *brw, uint32_t flags, struct brw_bo *bo, uint32_t offset, uint64_t imm) { brw->vtbl.emit_raw_pipe_control(brw, flags, bo, offset, imm); } /** * Restriction [DevSNB, DevIVB]: * * Prior to changing Depth/Stencil Buffer state (i.e. any combination of * 3DSTATE_DEPTH_BUFFER, 3DSTATE_CLEAR_PARAMS, 3DSTATE_STENCIL_BUFFER, * 3DSTATE_HIER_DEPTH_BUFFER) SW must first issue a pipelined depth stall * (PIPE_CONTROL with Depth Stall bit set), followed by a pipelined depth * cache flush (PIPE_CONTROL with Depth Flush Bit set), followed by * another pipelined depth stall (PIPE_CONTROL with Depth Stall bit set), * unless SW can otherwise guarantee that the pipeline from WM onwards is * already flushed (e.g., via a preceding MI_FLUSH). */ void brw_emit_depth_stall_flushes(struct brw_context *brw) { const struct gen_device_info *devinfo = &brw->screen->devinfo; assert(devinfo->gen >= 6); /* Starting on BDW, these pipe controls are unnecessary. * * WM HW will internally manage the draining pipe and flushing of the caches * when this command is issued. The PIPE_CONTROL restrictions are removed. */ if (devinfo->gen >= 8) return; brw_emit_pipe_control_flush(brw, PIPE_CONTROL_DEPTH_STALL); brw_emit_pipe_control_flush(brw, PIPE_CONTROL_DEPTH_CACHE_FLUSH); brw_emit_pipe_control_flush(brw, PIPE_CONTROL_DEPTH_STALL); } /** * From the Ivybridge PRM, Volume 2 Part 1, Section 3.2 (VS Stage Input): * "A PIPE_CONTROL with Post-Sync Operation set to 1h and a depth * stall needs to be sent just prior to any 3DSTATE_VS, 3DSTATE_URB_VS, * 3DSTATE_CONSTANT_VS, 3DSTATE_BINDING_TABLE_POINTER_VS, * 3DSTATE_SAMPLER_STATE_POINTER_VS command. Only one PIPE_CONTROL needs * to be sent before any combination of VS associated 3DSTATE." */ void gen7_emit_vs_workaround_flush(struct brw_context *brw) { ASSERTED const struct gen_device_info *devinfo = &brw->screen->devinfo; assert(devinfo->gen == 7); brw_emit_pipe_control_write(brw, PIPE_CONTROL_WRITE_IMMEDIATE | PIPE_CONTROL_DEPTH_STALL, brw->workaround_bo, brw->workaround_bo_offset, 0); } /** * From the PRM, Volume 2a: * * "Indirect State Pointers Disable * * At the completion of the post-sync operation associated with this pipe * control packet, the indirect state pointers in the hardware are * considered invalid; the indirect pointers are not saved in the context. * If any new indirect state commands are executed in the command stream * while the pipe control is pending, the new indirect state commands are * preserved. * * [DevIVB+]: Using Invalidate State Pointer (ISP) only inhibits context * restoring of Push Constant (3DSTATE_CONSTANT_*) commands. Push Constant * commands are only considered as Indirect State Pointers. Once ISP is * issued in a context, SW must initialize by programming push constant * commands for all the shaders (at least to zero length) before attempting * any rendering operation for the same context." * * 3DSTATE_CONSTANT_* packets are restored during a context restore, * even though they point to a BO that has been already unreferenced at * the end of the previous batch buffer. This has been fine so far since * we are protected by these scratch page (every address not covered by * a BO should be pointing to the scratch page). But on CNL, it is * causing a GPU hang during context restore at the 3DSTATE_CONSTANT_* * instruction. * * The flag "Indirect State Pointers Disable" in PIPE_CONTROL tells the * hardware to ignore previous 3DSTATE_CONSTANT_* packets during a * context restore, so the mentioned hang doesn't happen. However, * software must program push constant commands for all stages prior to * rendering anything, so we flag them as dirty. * * Finally, we also make sure to stall at pixel scoreboard to make sure the * constants have been loaded into the EUs prior to disable the push constants * so that it doesn't hang a previous 3DPRIMITIVE. */ void gen7_emit_isp_disable(struct brw_context *brw) { brw->vtbl.emit_raw_pipe_control(brw, PIPE_CONTROL_STALL_AT_SCOREBOARD | PIPE_CONTROL_CS_STALL, NULL, 0, 0); brw->vtbl.emit_raw_pipe_control(brw, PIPE_CONTROL_INDIRECT_STATE_POINTERS_DISABLE | PIPE_CONTROL_CS_STALL, NULL, 0, 0); brw->vs.base.push_constants_dirty = true; brw->tcs.base.push_constants_dirty = true; brw->tes.base.push_constants_dirty = true; brw->gs.base.push_constants_dirty = true; brw->wm.base.push_constants_dirty = true; } /** * Emit a PIPE_CONTROL command for gen7 with the CS Stall bit set. */ void gen7_emit_cs_stall_flush(struct brw_context *brw) { brw_emit_pipe_control_write(brw, PIPE_CONTROL_CS_STALL | PIPE_CONTROL_WRITE_IMMEDIATE, brw->workaround_bo, brw->workaround_bo_offset, 0); } /** * Emits a PIPE_CONTROL with a non-zero post-sync operation, for * implementing two workarounds on gen6. From section 1.4.7.1 * "PIPE_CONTROL" of the Sandy Bridge PRM volume 2 part 1: * * [DevSNB-C+{W/A}] Before any depth stall flush (including those * produced by non-pipelined state commands), software needs to first * send a PIPE_CONTROL with no bits set except Post-Sync Operation != * 0. * * [Dev-SNB{W/A}]: Before a PIPE_CONTROL with Write Cache Flush Enable * =1, a PIPE_CONTROL with any non-zero post-sync-op is required. * * And the workaround for these two requires this workaround first: * * [Dev-SNB{W/A}]: Pipe-control with CS-stall bit set must be sent * BEFORE the pipe-control with a post-sync op and no write-cache * flushes. * * And this last workaround is tricky because of the requirements on * that bit. From section 1.4.7.2.3 "Stall" of the Sandy Bridge PRM * volume 2 part 1: * * "1 of the following must also be set: * - Render Target Cache Flush Enable ([12] of DW1) * - Depth Cache Flush Enable ([0] of DW1) * - Stall at Pixel Scoreboard ([1] of DW1) * - Depth Stall ([13] of DW1) * - Post-Sync Operation ([13] of DW1) * - Notify Enable ([8] of DW1)" * * The cache flushes require the workaround flush that triggered this * one, so we can't use it. Depth stall would trigger the same. * Post-sync nonzero is what triggered this second workaround, so we * can't use that one either. Notify enable is IRQs, which aren't * really our business. That leaves only stall at scoreboard. */ void brw_emit_post_sync_nonzero_flush(struct brw_context *brw) { brw_emit_pipe_control_flush(brw, PIPE_CONTROL_CS_STALL | PIPE_CONTROL_STALL_AT_SCOREBOARD); brw_emit_pipe_control_write(brw, PIPE_CONTROL_WRITE_IMMEDIATE, brw->workaround_bo, brw->workaround_bo_offset, 0); } /* * From Sandybridge PRM, volume 2, "1.7.2 End-of-Pipe Synchronization": * * Write synchronization is a special case of end-of-pipe * synchronization that requires that the render cache and/or depth * related caches are flushed to memory, where the data will become * globally visible. This type of synchronization is required prior to * SW (CPU) actually reading the result data from memory, or initiating * an operation that will use as a read surface (such as a texture * surface) a previous render target and/or depth/stencil buffer * * * From Haswell PRM, volume 2, part 1, "End-of-Pipe Synchronization": * * Exercising the write cache flush bits (Render Target Cache Flush * Enable, Depth Cache Flush Enable, DC Flush) in PIPE_CONTROL only * ensures the write caches are flushed and doesn't guarantee the data * is globally visible. * * SW can track the completion of the end-of-pipe-synchronization by * using "Notify Enable" and "PostSync Operation - Write Immediate * Data" in the PIPE_CONTROL command. */ void brw_emit_end_of_pipe_sync(struct brw_context *brw, uint32_t flags) { const struct gen_device_info *devinfo = &brw->screen->devinfo; if (devinfo->gen >= 6) { /* From Sandybridge PRM, volume 2, "1.7.3.1 Writing a Value to Memory": * * "The most common action to perform upon reaching a synchronization * point is to write a value out to memory. An immediate value * (included with the synchronization command) may be written." * * * From Broadwell PRM, volume 7, "End-of-Pipe Synchronization": * * "In case the data flushed out by the render engine is to be read * back in to the render engine in coherent manner, then the render * engine has to wait for the fence completion before accessing the * flushed data. This can be achieved by following means on various * products: PIPE_CONTROL command with CS Stall and the required * write caches flushed with Post-Sync-Operation as Write Immediate * Data. * * Example: * - Workload-1 (3D/GPGPU/MEDIA) * - PIPE_CONTROL (CS Stall, Post-Sync-Operation Write Immediate * Data, Required Write Cache Flush bits set) * - Workload-2 (Can use the data produce or output by Workload-1) */ brw_emit_pipe_control_write(brw, flags | PIPE_CONTROL_CS_STALL | PIPE_CONTROL_WRITE_IMMEDIATE, brw->workaround_bo, brw->workaround_bo_offset, 0); if (devinfo->is_haswell) { /* Haswell needs addition work-arounds: * * From Haswell PRM, volume 2, part 1, "End-of-Pipe Synchronization": * * Option 1: * PIPE_CONTROL command with the CS Stall and the required write * caches flushed with Post-SyncOperation as Write Immediate Data * followed by eight dummy MI_STORE_DATA_IMM (write to scratch * spce) commands. * * Example: * - Workload-1 * - PIPE_CONTROL (CS Stall, Post-Sync-Operation Write * Immediate Data, Required Write Cache Flush bits set) * - MI_STORE_DATA_IMM (8 times) (Dummy data, Scratch Address) * - Workload-2 (Can use the data produce or output by * Workload-1) * * Unfortunately, both the PRMs and the internal docs are a bit * out-of-date in this regard. What the windows driver does (and * this appears to actually work) is to emit a register read from the * memory address written by the pipe control above. * * What register we load into doesn't matter. We choose an indirect * rendering register because we know it always exists and it's one * of the first registers the command parser allows us to write. If * you don't have command parser support in your kernel (pre-4.2), * this will get turned into MI_NOOP and you won't get the * workaround. Unfortunately, there's just not much we can do in * that case. This register is perfectly safe to write since we * always re-load all of the indirect draw registers right before * 3DPRIMITIVE when needed anyway. */ brw_load_register_mem(brw, GEN7_3DPRIM_START_INSTANCE, brw->workaround_bo, brw->workaround_bo_offset); } } else { /* On gen4-5, a regular pipe control seems to suffice. */ brw_emit_pipe_control_flush(brw, flags); } } /* Emit a pipelined flush to either flush render and texture cache for * reading from a FBO-drawn texture, or flush so that frontbuffer * render appears on the screen in DRI1. * * This is also used for the always_flush_cache driconf debug option. */ void brw_emit_mi_flush(struct brw_context *brw) { const struct gen_device_info *devinfo = &brw->screen->devinfo; int flags = PIPE_CONTROL_RENDER_TARGET_FLUSH; if (devinfo->gen >= 6) { flags |= PIPE_CONTROL_INSTRUCTION_INVALIDATE | PIPE_CONTROL_CONST_CACHE_INVALIDATE | PIPE_CONTROL_DATA_CACHE_FLUSH | PIPE_CONTROL_DEPTH_CACHE_FLUSH | PIPE_CONTROL_VF_CACHE_INVALIDATE | PIPE_CONTROL_TEXTURE_CACHE_INVALIDATE | PIPE_CONTROL_CS_STALL; } brw_emit_pipe_control_flush(brw, flags); } static bool init_identifier_bo(struct brw_context *brw) { void *bo_map; if (!can_do_exec_capture(brw->screen)) return true; bo_map = brw_bo_map(NULL, brw->workaround_bo, MAP_READ | MAP_WRITE); if (!bo_map) return false; brw->workaround_bo->kflags |= EXEC_OBJECT_CAPTURE; brw->workaround_bo_offset = ALIGN(intel_debug_write_identifiers(bo_map, 4096, "i965") + 8, 8); brw_bo_unmap(brw->workaround_bo); return true; } int brw_init_pipe_control(struct brw_context *brw, const struct gen_device_info *devinfo) { switch (devinfo->gen) { case 11: brw->vtbl.emit_raw_pipe_control = gen11_emit_raw_pipe_control; break; case 9: brw->vtbl.emit_raw_pipe_control = gen9_emit_raw_pipe_control; break; case 8: brw->vtbl.emit_raw_pipe_control = gen8_emit_raw_pipe_control; break; case 7: brw->vtbl.emit_raw_pipe_control = devinfo->is_haswell ? gen75_emit_raw_pipe_control : gen7_emit_raw_pipe_control; break; case 6: brw->vtbl.emit_raw_pipe_control = gen6_emit_raw_pipe_control; break; case 5: brw->vtbl.emit_raw_pipe_control = gen5_emit_raw_pipe_control; break; case 4: brw->vtbl.emit_raw_pipe_control = devinfo->is_g4x ? gen45_emit_raw_pipe_control : gen4_emit_raw_pipe_control; break; default: unreachable("Unhandled Gen."); } if (devinfo->gen < 6) return 0; /* We can't just use brw_state_batch to get a chunk of space for * the gen6 workaround because it involves actually writing to * the buffer, and the kernel doesn't let us write to the batch. */ brw->workaround_bo = brw_bo_alloc(brw->bufmgr, "workaround", 4096, BRW_MEMZONE_OTHER); if (brw->workaround_bo == NULL) return -ENOMEM; if (!init_identifier_bo(brw)) return -ENOMEM; /* Couldn't map workaround_bo?? */ brw->workaround_bo_offset = 0; brw->pipe_controls_since_last_cs_stall = 0; return 0; } void brw_fini_pipe_control(struct brw_context *brw) { brw_bo_unreference(brw->workaround_bo); }