1TF-A Build Instructions for Marvell Platforms 2============================================= 3 4This section describes how to compile the Trusted Firmware-A (TF-A) project for Marvell's platforms. 5 6Build Instructions 7------------------ 8(1) Set the cross compiler 9 10 .. code:: shell 11 12 > export CROSS_COMPILE=/path/to/toolchain/aarch64-linux-gnu- 13 14(2) Set path for FIP images: 15 16Set U-Boot image path (relatively to TF-A root or absolute path) 17 18 .. code:: shell 19 20 > export BL33=path/to/u-boot.bin 21 22For example: if U-Boot project (and its images) is located at ``~/project/u-boot``, 23BL33 should be ``~/project/u-boot/u-boot.bin`` 24 25 .. note:: 26 27 *u-boot.bin* should be used and not *u-boot-spl.bin* 28 29Set MSS/SCP image path (mandatory only for A7K/8K/CN913x) 30 31 .. code:: shell 32 33 > export SCP_BL2=path/to/mrvl_scp_bl2*.img 34 35(3) Armada-37x0 build requires WTP tools installation. 36 37See below in the section "Tools and external components installation". 38Install ARM 32-bit cross compiler, which is required for building WTMI image for CM3 39 40 .. code:: shell 41 42 > sudo apt-get install gcc-arm-linux-gnueabi 43 44(4) Clean previous build residuals (if any) 45 46 .. code:: shell 47 48 > make distclean 49 50(5) Build TF-A 51 52There are several build options: 53 54- PLAT 55 56 Supported Marvell platforms are: 57 58 - a3700 - A3720 DB, EspressoBin and Turris MOX 59 - a70x0 60 - a70x0_amc - AMC board 61 - a80x0 62 - a80x0_mcbin - MacchiatoBin 63 - a80x0_puzzle - IEI Puzzle-M801 64 - t9130 - CN913x 65 66- DEBUG 67 68 Default is without debug information (=0). in order to enable it use ``DEBUG=1``. 69 Must be disabled when building UART recovery images due to current console driver 70 implementation that is not compatible with Xmodem protocol used for boot image download. 71 72- LOG_LEVEL 73 74 Defines the level of logging which will be purged to the default output port. 75 76 - 0 - LOG_LEVEL_NONE 77 - 10 - LOG_LEVEL_ERROR 78 - 20 - LOG_LEVEL_NOTICE (default for DEBUG=0) 79 - 30 - LOG_LEVEL_WARNING 80 - 40 - LOG_LEVEL_INFO (default for DEBUG=1) 81 - 50 - LOG_LEVEL_VERBOSE 82 83- USE_COHERENT_MEM 84 85 This flag determines whether to include the coherent memory region in the 86 BL memory map or not. Enabled by default. 87 88- LLC_ENABLE 89 90 Flag defining the LLC (L3) cache state. The cache is enabled by default (``LLC_ENABLE=1``). 91 92- LLC_SRAM 93 94 Flag enabling the LLC (L3) cache SRAM support. The LLC SRAM is activated and used 95 by Trusted OS (OP-TEE OS, BL32). The TF-A only prepares CCU address translation windows 96 for SRAM address range at BL31 execution stage with window target set to DRAM-0. 97 When Trusted OS activates LLC SRAM, the CCU window target is changed to SRAM. 98 There is no reason to enable this feature if OP-TEE OS built with CFG_WITH_PAGER=n. 99 Only set LLC_SRAM=1 if OP-TEE OS is built with CFG_WITH_PAGER=y. 100 101- CM3_SYSTEM_RESET 102 103 For Armada37x0 only, when ``CM3_SYSTEM_RESET=1``, the Cortex-M3 secure coprocessor will 104 be used for system reset. 105 TF-A will send command 0x0009 with a magic value via the rWTM mailbox interface to the 106 Cortex-M3 secure coprocessor. 107 The firmware running in the coprocessor must either implement this functionality or 108 ignore the 0x0009 command (which is true for the firmware from A3700-utils-marvell 109 repository). If this option is enabled but the firmware does not support this command, 110 an error message will be printed prior trying to reboot via the usual way. 111 112 This option is needed on Turris MOX as a workaround to a HW bug which causes reset to 113 sometime hang the board. 114 115- MARVELL_SECURE_BOOT 116 117 Build trusted(=1)/non trusted(=0) image, default is non trusted. 118 119- BLE_PATH 120 121 Points to BLE (Binary ROM extension) sources folder. 122 Only required for A7K/8K/CN913x builds. 123 The parameter is optional, its default value is ``plat/marvell/armada/a8k/common/ble``. 124 125- MV_DDR_PATH 126 127 For A7K/8K/CN913x, use this parameter to point to mv_ddr driver sources to allow BLE build. For A37x0, 128 it is used for ddr_tool build. 129 130 Usage example: MV_DDR_PATH=path/to/mv_ddr 131 132 The parameter is optional for A7K/8K/CN913x, when this parameter is not set, the mv_ddr 133 sources are expected to be located at: drivers/marvell/mv_ddr. However, the parameter 134 is necessary for A37x0. 135 136 For the mv_ddr source location, check the section "Tools and external components installation" 137 138 If MV_DDR_PATH source code is a git snapshot then provide path to the full git 139 repository (including .git subdir) because mv_ddr build process calls git commands. 140 141- CP_NUM 142 143 Total amount of CPs (South Bridge) connected to AP. When the parameter is omitted, 144 the build uses the default number of CPs, which is a number of embedded CPs inside the 145 package: 1 or 2 depending on the SoC used. The parameter is valid for OcteonTX2 CN913x SoC 146 family (PLAT=t9130), which can have external CPs connected to the MCI ports. Valid 147 values with CP_NUM are in a range of 1 to 3. 148 149- DDR_TOPOLOGY 150 151 For Armada37x0 only, the DDR topology map index/name, default is 0. 152 153 Supported Options: 154 - 0 - DDR3 1CS 512MB (DB-88F3720-DDR3-Modular, EspressoBin V3-V5) 155 - 1 - DDR4 1CS 512MB (DB-88F3720-DDR4-Modular) 156 - 2 - DDR3 2CS 1GB (EspressoBin V3-V5) 157 - 3 - DDR4 2CS 4GB (DB-88F3720-DDR4-Modular) 158 - 4 - DDR3 1CS 1GB (DB-88F3720-DDR3-Modular, EspressoBin V3-V5) 159 - 5 - DDR4 1CS 1GB (EspressoBin V7, EspressoBin-Ultra) 160 - 6 - DDR4 2CS 2GB (EspressoBin V7) 161 - 7 - DDR3 2CS 2GB (EspressoBin V3-V5) 162 - CUST - CUSTOMER BOARD (Customer board settings) 163 164- CLOCKSPRESET 165 166 For Armada37x0 only, the clock tree configuration preset including CPU and DDR frequency, 167 default is CPU_800_DDR_800. 168 169 - CPU_600_DDR_600 - CPU at 600 MHz, DDR at 600 MHz 170 - CPU_800_DDR_800 - CPU at 800 MHz, DDR at 800 MHz 171 - CPU_1000_DDR_800 - CPU at 1000 MHz, DDR at 800 MHz 172 - CPU_1200_DDR_750 - CPU at 1200 MHz, DDR at 750 MHz 173 174 Look at Armada37x0 chip package marking on board to identify correct CPU frequency. 175 The last line on package marking (next line after the 88F37x0 line) should contain: 176 177 - C080 or I080 - chip with 800 MHz CPU - use ``CLOCKSPRESET=CPU_800_DDR_800`` 178 - C100 or I100 - chip with 1000 MHz CPU - use ``CLOCKSPRESET=CPU_1000_DDR_800`` 179 - C120 - chip with 1200 MHz CPU - use ``CLOCKSPRESET=CPU_1200_DDR_750`` 180 181- BOOTDEV 182 183 For Armada37x0 only, the flash boot device, default is ``SPINOR``. 184 185 Currently, Armada37x0 only supports ``SPINOR``, ``SPINAND``, ``EMMCNORM`` and ``SATA``: 186 187 - SPINOR - SPI NOR flash boot 188 - SPINAND - SPI NAND flash boot 189 - EMMCNORM - eMMC Download Mode 190 191 Download boot loader or program code from eMMC flash into CM3 or CA53 192 Requires full initialization and command sequence 193 194 - SATA - SATA device boot 195 196 Image needs to be stored at disk LBA 0 or at disk partition with 197 MBR type 0x4d (ASCII 'M' as in Marvell) or at disk partition with 198 GPT name ``MARVELL BOOT PARTITION``. 199 200- PARTNUM 201 202 For Armada37x0 only, the boot partition number, default is 0. 203 204 To boot from eMMC, the value should be aligned with the parameter in 205 U-Boot with name of ``CONFIG_SYS_MMC_ENV_PART``, whose value by default is 206 1. For details about CONFIG_SYS_MMC_ENV_PART, please refer to the U-Boot 207 build instructions. 208 209- WTMI_IMG 210 211 For Armada37x0 only, the path of the binary can point to an image which 212 does nothing, an image which supports EFUSE or a customized CM3 firmware 213 binary. The default image is ``fuse.bin`` that built from sources in WTP 214 folder, which is the next option. If the default image is OK, then this 215 option should be skipped. 216 217 Please note that this is not a full WTMI image, just a main loop without 218 hardware initialization code. Final WTMI image is built from this WTMI_IMG 219 binary and sys-init code from the WTP directory which sets DDR and CPU 220 clocks according to DDR_TOPOLOGY and CLOCKSPRESET options. 221 222- WTP 223 224 For Armada37x0 only, use this parameter to point to wtptools source code 225 directory, which can be found as a3700_utils.zip in the release. Usage 226 example: ``WTP=/path/to/a3700_utils`` 227 228 If WTP source code is a git snapshot then provide path to the full git 229 repository (including .git subdir) because WTP build process calls git commands. 230 231- CRYPTOPP_PATH 232 233 For Armada37x0 only, use this parameter to point to Crypto++ source code 234 directory. If this option is specified then Crypto++ source code in 235 CRYPTOPP_PATH directory will be automatically compiled. Crypto++ library 236 is required for building WTP image tool. Either CRYPTOPP_PATH or 237 CRYPTOPP_LIBDIR with CRYPTOPP_INCDIR needs to be specified for Armada37x0. 238 239- CRYPTOPP_LIBDIR 240 241 For Armada37x0 only, use this parameter to point to the directory with 242 compiled Crypto++ library. By default it points to the CRYPTOPP_PATH. 243 244- CRYPTOPP_INCDIR 245 246 For Armada37x0 only, use this parameter to point to the directory with 247 header files of Crypto++ library. By default it points to the CRYPTOPP_PATH. 248 249 250For example, in order to build the image in debug mode with log level up to 'notice' level run 251 252.. code:: shell 253 254 > make DEBUG=1 USE_COHERENT_MEM=0 LOG_LEVEL=20 PLAT=<MARVELL_PLATFORM> mrvl_flash 255 256And if we want to build a Armada37x0 image in debug mode with log level up to 'notice' level, 257the image has the preset CPU at 1000 MHz, preset DDR3 at 800 MHz, the DDR topology of DDR4 2CS, 258the image boot from SPI NOR flash partition 0, and the image is non trusted in WTP, the command 259line is as following 260 261.. code:: shell 262 263 > make DEBUG=1 USE_COHERENT_MEM=0 LOG_LEVEL=20 CLOCKSPRESET=CPU_1000_DDR_800 \ 264 MARVELL_SECURE_BOOT=0 DDR_TOPOLOGY=3 BOOTDEV=SPINOR PARTNUM=0 PLAT=a3700 \ 265 MV_DDR_PATH=/path/to/mv-ddr-marvell/ WTP=/path/to/A3700-utils-marvell/ \ 266 CRYPTOPP_PATH=/path/to/cryptopp/ BL33=/path/to/u-boot.bin \ 267 all fip mrvl_bootimage mrvl_flash mrvl_uart 268 269To build just TF-A without WTMI image (useful for A3720 Turris MOX board), run following command: 270 271.. code:: shell 272 273 > make USE_COHERENT_MEM=0 PLAT=a3700 CM3_SYSTEM_RESET=1 BL33=/path/to/u-boot.bin \ 274 CROSS_COMPILE=aarch64-linux-gnu- mrvl_bootimage 275 276Here is full example how to build production release of Marvell firmware image (concatenated 277binary of Marvell secure firmware, TF-A and U-Boot) for EspressoBin board (PLAT=a3700) with 2781GHz CPU (CLOCKSPRESET=CPU_1000_DDR_800) and 1GB DDR4 RAM (DDR_TOPOLOGY=5): 279 280.. code:: shell 281 282 > git clone https://review.trustedfirmware.org/TF-A/trusted-firmware-a 283 > git clone https://gitlab.denx.de/u-boot/u-boot.git 284 > git clone https://github.com/weidai11/cryptopp.git 285 > git clone https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git -b master 286 > git clone https://github.com/MarvellEmbeddedProcessors/A3700-utils-marvell.git -b master 287 > make -C u-boot CROSS_COMPILE=aarch64-linux-gnu- mvebu_espressobin-88f3720_defconfig u-boot.bin 288 > make -C trusted-firmware-a CROSS_COMPILE=aarch64-linux-gnu- CROSS_CM3=arm-linux-gnueabi- \ 289 USE_COHERENT_MEM=0 PLAT=a3700 CLOCKSPRESET=CPU_1000_DDR_800 DDR_TOPOLOGY=5 \ 290 MV_DDR_PATH=$PWD/mv-ddr-marvell/ WTP=$PWD/A3700-utils-marvell/ CRYPTOPP_PATH=$PWD/cryptopp/ \ 291 BL33=$PWD/u-boot/u-boot.bin mrvl_flash 292 293Produced Marvell firmware flash image: ``trusted-firmware-a/build/a3700/release/flash-image.bin`` 294 295Special Build Flags 296-------------------- 297 298- PLAT_RECOVERY_IMAGE_ENABLE 299 When set this option to enable secondary recovery function when build atf. 300 In order to build UART recovery image this operation should be disabled for 301 A7K/8K/CN913x because of hardware limitation (boot from secondary image 302 can interrupt UART recovery process). This MACRO definition is set in 303 ``plat/marvell/armada/a8k/common/include/platform_def.h`` file. 304 305- DDR32 306 In order to work in 32bit DDR, instead of the default 64bit ECC DDR, 307 this flag should be set to 1. 308 309For more information about build options, please refer to the 310:ref:`Build Options` document. 311 312 313Build output 314------------ 315Marvell's TF-A compilation generates 8 files: 316 317 - ble.bin - BLe image (not available for Armada37x0) 318 - bl1.bin - BL1 image 319 - bl2.bin - BL2 image 320 - bl31.bin - BL31 image 321 - fip.bin - FIP image (contains BL2, BL31 & BL33 (U-Boot) images) 322 - boot-image.bin - TF-A image (contains BL1 and FIP images) 323 - flash-image.bin - Flashable Marvell firmware image. For Armada37x0 it 324 contains TIM, WTMI and boot-image.bin images. For other platforms it contains 325 BLe and boot-image.bin images. Should be placed on the boot flash/device. 326 - uart-images.tgz.bin - GZIPed TAR archive which contains Armada37x0 images 327 for booting via UART. Could be loaded via Marvell's WtpDownload tool from 328 A3700-utils-marvell repository. 329 330Additional make target ``mrvl_bootimage`` produce ``boot-image.bin`` file. Target 331``mrvl_flash`` produce final ``flash-image.bin`` file and target ``mrvl_uart`` 332produce ``uart-images.tgz.bin`` file. 333 334 335Tools and external components installation 336------------------------------------------ 337 338Armada37x0 Builds require installation of 3 components 339~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 340 341(1) ARM cross compiler capable of building images for the service CPU (CM3). 342 This component is usually included in the Linux host packages. 343 On Debian/Ubuntu hosts the default GNU ARM tool chain can be installed 344 using the following command 345 346 .. code:: shell 347 348 > sudo apt-get install gcc-arm-linux-gnueabi 349 350 Only if required, the default tool chain prefix ``arm-linux-gnueabi-`` can be 351 overwritten using the environment variable ``CROSS_CM3``. 352 Example for BASH shell 353 354 .. code:: shell 355 356 > export CROSS_CM3=/opt/arm-cross/bin/arm-linux-gnueabi 357 358(2) DDR initialization library sources (mv_ddr) available at the following repository 359 (use the "master" branch): 360 361 https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git 362 363(3) Armada3700 tools available at the following repository 364 (use the "master" branch): 365 366 https://github.com/MarvellEmbeddedProcessors/A3700-utils-marvell.git 367 368(4) Crypto++ library available at the following repository: 369 370 https://github.com/weidai11/cryptopp.git 371 372Armada70x0 and Armada80x0 Builds require installation of an additional component 373~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 374 375(1) DDR initialization library sources (mv_ddr) available at the following repository 376 (use the "master" branch): 377 378 https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git 379