1# 2# Copyright (c) 2016-2021, ARM Limited. All rights reserved. 3# 4# SPDX-License-Identifier: BSD-3-Clause 5# 6 7# Default, static values for build variables, listed in alphabetic order. 8# Dependencies between build options, if any, are handled in the top-level 9# Makefile, after this file is included. This ensures that the former is better 10# poised to handle dependencies, as all build variables would have a default 11# value by then. 12 13# Use T32 by default 14AARCH32_INSTRUCTION_SET := T32 15 16# The AArch32 Secure Payload to be built as BL32 image 17AARCH32_SP := none 18 19# The Target build architecture. Supported values are: aarch64, aarch32. 20ARCH := aarch64 21 22# ARM Architecture feature modifiers: none by default 23ARM_ARCH_FEATURE := none 24 25# ARM Architecture major and minor versions: 8.0 by default. 26ARM_ARCH_MAJOR := 8 27ARM_ARCH_MINOR := 0 28 29# Base commit to perform code check on 30BASE_COMMIT := origin/master 31 32# Execute BL2 at EL3 33BL2_AT_EL3 := 0 34 35# BL2 image is stored in XIP memory, for now, this option is only supported 36# when BL2_AT_EL3 is 1. 37BL2_IN_XIP_MEM := 0 38 39# Do dcache invalidate upon BL2 entry at EL3 40BL2_INV_DCACHE := 1 41 42# Select the branch protection features to use. 43BRANCH_PROTECTION := 0 44 45# By default, consider that the platform may release several CPUs out of reset. 46# The platform Makefile is free to override this value. 47COLD_BOOT_SINGLE_CPU := 0 48 49# Flag to compile in coreboot support code. Exclude by default. The coreboot 50# Makefile system will set this when compiling TF as part of a coreboot image. 51COREBOOT := 0 52 53# For Chain of Trust 54CREATE_KEYS := 1 55 56# Build flag to include AArch32 registers in cpu context save and restore during 57# world switch. This flag must be set to 0 for AArch64-only platforms. 58CTX_INCLUDE_AARCH32_REGS := 1 59 60# Include FP registers in cpu context 61CTX_INCLUDE_FPREGS := 0 62 63# Include pointer authentication (ARMv8.3-PAuth) registers in cpu context. This 64# must be set to 1 if the platform wants to use this feature in the Secure 65# world. It is not needed to use it in the Non-secure world. 66CTX_INCLUDE_PAUTH_REGS := 0 67 68# Include Nested virtualization control (Armv8.4-NV) registers in cpu context. 69# This must be set to 1 if architecture implements Nested Virtualization 70# Extension and platform wants to use this feature in the Secure world 71CTX_INCLUDE_NEVE_REGS := 0 72 73# Debug build 74DEBUG := 0 75 76# By default disable authenticated decryption support. 77DECRYPTION_SUPPORT := none 78 79# Build platform 80DEFAULT_PLAT := fvp 81 82# Disable the generation of the binary image (ELF only). 83DISABLE_BIN_GENERATION := 0 84 85# Disable MTPMU if FEAT_MTPMU is supported. Default is 0 to keep backwards 86# compatibility. 87DISABLE_MTPMU := 0 88 89# Enable capability to disable authentication dynamically. Only meant for 90# development platforms. 91DYN_DISABLE_AUTH := 0 92 93# Build option to enable MPAM for lower ELs 94ENABLE_MPAM_FOR_LOWER_ELS := 0 95 96# Flag to Enable Position Independant support (PIE) 97ENABLE_PIE := 0 98 99# Flag to enable Performance Measurement Framework 100ENABLE_PMF := 0 101 102# Flag to enable PSCI STATs functionality 103ENABLE_PSCI_STAT := 0 104 105# Flag to enable runtime instrumentation using PMF 106ENABLE_RUNTIME_INSTRUMENTATION := 0 107 108# Flag to enable stack corruption protection 109ENABLE_STACK_PROTECTOR := 0 110 111# Flag to enable exception handling in EL3 112EL3_EXCEPTION_HANDLING := 0 113 114# Flag to enable Branch Target Identification. 115# Internal flag not meant for direct setting. 116# Use BRANCH_PROTECTION to enable BTI. 117ENABLE_BTI := 0 118 119# Flag to enable Pointer Authentication. 120# Internal flag not meant for direct setting. 121# Use BRANCH_PROTECTION to enable PAUTH. 122ENABLE_PAUTH := 0 123 124# By default BL31 encryption disabled 125ENCRYPT_BL31 := 0 126 127# By default BL32 encryption disabled 128ENCRYPT_BL32 := 0 129 130# Default dummy firmware encryption key 131ENC_KEY := 1234567890abcdef1234567890abcdef1234567890abcdef1234567890abcdef 132 133# Default dummy nonce for firmware encryption 134ENC_NONCE := 1234567890abcdef12345678 135 136# Build flag to treat usage of deprecated platform and framework APIs as error. 137ERROR_DEPRECATED := 0 138 139# Fault injection support 140FAULT_INJECTION_SUPPORT := 0 141 142# Byte alignment that each component in FIP is aligned to 143FIP_ALIGN := 0 144 145# Default FIP file name 146FIP_NAME := fip.bin 147 148# Default FWU_FIP file name 149FWU_FIP_NAME := fwu_fip.bin 150 151# By default firmware encryption with SSK 152FW_ENC_STATUS := 0 153 154# For Chain of Trust 155GENERATE_COT := 0 156 157# Hint platform interrupt control layer that Group 0 interrupts are for EL3. By 158# default, they are for Secure EL1. 159GICV2_G0_FOR_EL3 := 0 160 161# Route External Aborts to EL3. Disabled by default; External Aborts are handled 162# by lower ELs. 163HANDLE_EA_EL3_FIRST := 0 164 165# Secure hash algorithm flag, accepts 3 values: sha256, sha384 and sha512. 166# The default value is sha256. 167HASH_ALG := sha256 168 169# Whether system coherency is managed in hardware, without explicit software 170# operations. 171HW_ASSISTED_COHERENCY := 0 172 173# Set the default algorithm for the generation of Trusted Board Boot keys 174KEY_ALG := rsa 175 176# Set the default key size in case KEY_ALG is rsa 177ifeq ($(KEY_ALG),rsa) 178KEY_SIZE := 2048 179endif 180 181# Option to build TF with Measured Boot support 182MEASURED_BOOT := 0 183 184# NS timer register save and restore 185NS_TIMER_SWITCH := 0 186 187# Include lib/libc in the final image 188OVERRIDE_LIBC := 0 189 190# Build PL011 UART driver in minimal generic UART mode 191PL011_GENERIC_UART := 0 192 193# By default, consider that the platform's reset address is not programmable. 194# The platform Makefile is free to override this value. 195PROGRAMMABLE_RESET_ADDRESS := 0 196 197# Flag used to choose the power state format: Extended State-ID or Original 198PSCI_EXTENDED_STATE_ID := 0 199 200# Enable RAS support 201RAS_EXTENSION := 0 202 203# By default, BL1 acts as the reset handler, not BL31 204RESET_TO_BL31 := 0 205 206# For Chain of Trust 207SAVE_KEYS := 0 208 209# Software Delegated Exception support 210SDEI_SUPPORT := 0 211 212# True Random Number firmware Interface 213TRNG_SUPPORT := 0 214 215# Whether code and read-only data should be put on separate memory pages. The 216# platform Makefile is free to override this value. 217SEPARATE_CODE_AND_RODATA := 0 218 219# Put NOBITS sections (.bss, stacks, page tables, and coherent memory) in a 220# separate memory region, which may be discontiguous from the rest of BL31. 221SEPARATE_NOBITS_REGION := 0 222 223# If the BL31 image initialisation code is recalimed after use for the secondary 224# cores stack 225RECLAIM_INIT_CODE := 0 226 227# SPD choice 228SPD := none 229 230# Enable the Management Mode (MM)-based Secure Partition Manager implementation 231SPM_MM := 0 232 233# Use SPM at S-EL2 as a default config for SPMD 234SPMD_SPM_AT_SEL2 := 1 235 236# Flag to introduce an infinite loop in BL1 just before it exits into the next 237# image. This is meant to help debugging the post-BL2 phase. 238SPIN_ON_BL1_EXIT := 0 239 240# Flags to build TF with Trusted Boot support 241TRUSTED_BOARD_BOOT := 0 242 243# Build option to choose whether Trusted Firmware uses Coherent memory or not. 244USE_COHERENT_MEM := 1 245 246# Build option to add debugfs support 247USE_DEBUGFS := 0 248 249# Build option to fconf based io 250ARM_IO_IN_DTB := 0 251 252# Build option to support SDEI through fconf 253SDEI_IN_FCONF := 0 254 255# Build option to support Secure Interrupt descriptors through fconf 256SEC_INT_DESC_IN_FCONF := 0 257 258# Build option to choose whether Trusted Firmware uses library at ROM 259USE_ROMLIB := 0 260 261# Build option to choose whether the xlat tables of BL images can be read-only. 262# Note that this only serves as a higher level option to PLAT_RO_XLAT_TABLES, 263# which is the per BL-image option that actually enables the read-only tables 264# API. The reason for having this additional option is to have a common high 265# level makefile where we can check for incompatible features/build options. 266ALLOW_RO_XLAT_TABLES := 0 267 268# Chain of trust. 269COT := tbbr 270 271# Use tbbr_oid.h instead of platform_oid.h 272USE_TBBR_DEFS := 1 273 274# Build verbosity 275V := 0 276 277# Whether to enable D-Cache early during warm boot. This is usually 278# applicable for platforms wherein interconnect programming is not 279# required to enable cache coherency after warm reset (eg: single cluster 280# platforms). 281WARMBOOT_ENABLE_DCACHE_EARLY := 0 282 283# Build option to enable/disable the Statistical Profiling Extensions 284ENABLE_SPE_FOR_LOWER_ELS := 1 285 286# SPE is only supported on AArch64 so disable it on AArch32. 287ifeq (${ARCH},aarch32) 288 override ENABLE_SPE_FOR_LOWER_ELS := 0 289endif 290 291# Include Memory Tagging Extension registers in cpu context. This must be set 292# to 1 if the platform wants to use this feature in the Secure world and MTE is 293# enabled at ELX. 294CTX_INCLUDE_MTE_REGS := 0 295 296ENABLE_AMU := 0 297 298# By default, enable Scalable Vector Extension if implemented for Non-secure 299# lower ELs 300# Note SVE is only supported on AArch64 - therefore do not enable in AArch32 301ifneq (${ARCH},aarch32) 302 ENABLE_SVE_FOR_NS := 1 303else 304 override ENABLE_SVE_FOR_NS := 0 305endif 306 307SANITIZE_UB := off 308 309# For ARMv8.1 (AArch64) platforms, enabling this option selects the spinlock 310# implementation variant using the ARMv8.1-LSE compare-and-swap instruction. 311# Default: disabled 312USE_SPINLOCK_CAS := 0 313 314# Enable Link Time Optimization 315ENABLE_LTO := 0 316 317# Build flag to include EL2 registers in cpu context save and restore during 318# S-EL2 firmware entry/exit. This flag is to be used with SPD=spmd option. 319# Default is 0. 320CTX_INCLUDE_EL2_REGS := 0 321 322# Enable Memory tag extension which is supported for architecture greater 323# than Armv8.5-A 324# By default it is set to "no" 325SUPPORT_STACK_MEMTAG := no 326 327# Select workaround for AT speculative behaviour. 328ERRATA_SPECULATIVE_AT := 0 329 330# Trap RAS error record access from lower EL 331RAS_TRAP_LOWER_EL_ERR_ACCESS := 0 332 333# Build option to create cot descriptors using fconf 334COT_DESC_IN_DTB := 0 335 336# Build option to provide openssl directory path 337OPENSSL_DIR := /usr 338 339# Build option to use the SP804 timer instead of the generic one 340USE_SP804_TIMER := 0 341