Lines Matching refs:disk

163 position of your kernel on the disk. Thus you can load the kernel
303 Support reading data from any or all floppies or hard disk(s) recognized
321 In traditional disk calls (called @dfn{CHS mode}), there is a geometry
328 available. In LBA mode, GRUB can access the entire disk.
331 GRUB is basically a disk-based boot loader but also has network
389 disk. The number @samp{0} is the drive number, which is counted from
391 disk.
397 Here, @samp{hd} means it is a hard disk drive. The first integer
398 @samp{0} indicates the drive number, that is, the first hard disk, while
402 one. This expression means the second partition of the first hard disk
403 drive. In this case, GRUB uses one partition of the disk, instead of the
404 whole disk.
410 This specifies the first @dfn{extended partition} of the first hard disk
413 partitions on your hard disk.
419 This means the BSD @samp{a} partition of the second hard disk. If you
455 partition of the first hard disk drive. Note that the argument
471 drive (floppy or hard disk). There are two ways of doing that - either
478 have an emergency boot disk ready, so that you can rescue your computer
506 and the second block of the floppy disk, respectively.
541 the first sector of a hard disk, since it's easy to reinitialize it
545 definitely desirable, you'll need to create a GRUB boot disk, and
615 following will install GRUB into the MBR of the first IDE disk:
684 from GRUB and you don't have to make a floppy or hard disk image file,
758 load an operating system from an arbitrary disk/partition. However,
1005 If you have installed DOS (or Windows) on a non-first hard disk, you
1006 have to use the disk swapping technique, because that OS cannot boot
1025 onto one disk, because they could be confused if there are more than one
1034 and the second partition of the first hard disk, and you want to boot
1094 complete copy of a working system in a different partition or disk.
1342 This boots GNU/Hurd from the first hard disk.
1352 This boots GNU/Linux, but from the second hard disk.
1380 the third @sc{pc} slice of the first hard disk.
1413 # For installing GRUB into the hard disk
1414 title Install GRUB into the hard disk
1420 This will just (re)install GRUB onto the hard disk.
1440 Although GRUB is a disk-based boot loader, it does provide network
1507 use a machine which has no local disk. In this case, you need to obtain
1765 disk. Because of the size restriction, @file{stage1} encodes the
1816 GRUB uses a special syntax for specifying disk drives which can be
1864 The syntax @samp{(hd0)} represents using the entire disk (or the
1866 represents using the first partition of the disk (or the boot sector
1887 disk. If you omit the device name in an absolute file name, GRUB uses
2313 @sc{bios} drive @var{drive}. You can use this command to create a disk
2350 and multiple primary FAT partitions exist in one disk. See also
2648 and multiple primary partitions exist on one disk. See also
2782 extra messages are printed to show disk activity. This global debug flag
2844 partition, and @samp{[@var{disk-offset-sector}]} for low-level sector
2845 requests from the disk.
2925 disk @var{stage2_file} was installed on, rather than using the booting
2942 properly when booting from a hard disk drive. Therefore, you will
3026 Set the active partition on the root disk to GRUB's root device.
3027 This command is limited to @emph{primary} PC partitions on a hard disk.
3046 The example exchanges the order between the first hard disk and the
3047 second hard disk. See also @ref{DOS/Windows}.
3131 one. For example, if there is an IDE disk and a SCSI disk, and your
3132 FreeBSD root partition is on the SCSI disk, then use a @samp{1} for
3145 disk that GRUB can read, but setting the correct root device is still
3197 @command{root}. If @var{install_device} is a hard disk, then embed a
3198 Stage 1.5 in the disk if possible.
3284 The stage2 or stage1.5 is being read from a hard disk, and the attempt
3285 to determine the size and geometry of the hard disk failed.
3288 The stage2 or stage1.5 is being read from a floppy disk, and the attempt
3289 to determine the size and geometry of the floppy disk failed. It's listed
3294 A disk read error happened while trying to read the stage2 or stage1.5.
3297 The location of the stage2 or stage1.5 is not in the portion of the disk
3299 BIOS translated geometry has been changed by the user or the disk is
3396 everything else (like the disk/partition info) is OK.
3400 error caused by the sanity checks of the filesystem structure on disk
3411 happens if your disk is larger than the BIOS can handle (512MB for
3424 @item 21 : Selected disk does not exist
3426 refers to a disk or BIOS device that is not present or not recognized by
3431 a device- or full file name which isn't on the selected disk.
3438 This error is returned if a linear block address is outside of the disk
3440 disk or a bug in the code handling it in GRUB (it's a great debugging
3444 This error is returned if there is a disk read error when trying to
3445 probe or read data from a particular disk.
3462 This error is returned if there is a disk write error when trying to
3463 write to a particular disk. This would generally only occur during an
3482 @item 34 : No spare sectors on the disk
3483 This error is returned if a disk doesn't have enough spare space. This
3567 Disable writing to any disk.
3687 separate partition or a removable disk. Here is an example in which
3705 exists. You should use this option whenever you add/remove a disk
3782 is useful when you mount a disk which is used for another system.
3909 important: the geometries and the partition tables of your hard disk