1 /**************************************************************************
2 Etherboot - BOOTP/TFTP Bootstrap Program
3 LANCE NIC driver for Etherboot
4 Large portions borrowed from the Linux LANCE driver by Donald Becker
5 Ken Yap, July 1997
6 ***************************************************************************/
7
8 /*
9 * This program is free software; you can redistribute it and/or
10 * modify it under the terms of the GNU General Public License as
11 * published by the Free Software Foundation; either version 2, or (at
12 * your option) any later version.
13 */
14
15 /* to get some global routines like printf */
16 #include "etherboot.h"
17 /* to get the interface to the body of the program */
18 #include "nic.h"
19 #ifdef INCLUDE_LANCE
20 #include "pci.h"
21 #endif
22 #include "cards.h"
23
24 /* Offsets from base I/O address */
25 #if defined(INCLUDE_NE2100) || defined(INCLUDE_LANCE)
26 #define LANCE_ETH_ADDR 0x0
27 #define LANCE_DATA 0x10
28 #define LANCE_ADDR 0x12
29 #define LANCE_RESET 0x14
30 #define LANCE_BUS_IF 0x16
31 #define LANCE_TOTAL_SIZE 0x18
32 #endif
33 #ifdef INCLUDE_NI6510
34 #define LANCE_ETH_ADDR 0x8
35 #define LANCE_DATA 0x0
36 #define LANCE_ADDR 0x2
37 #define LANCE_RESET 0x4
38 #define LANCE_BUS_IF 0x6
39 #define LANCE_TOTAL_SIZE 0x10
40 #endif
41
42 /* lance_poll() now can use multiple Rx buffers to prevent packet loss. Set
43 * Set LANCE_LOG_RX_BUFFERS to 0..7 for 1, 2, 4, 8, 16, 32, 64 or 128 Rx
44 * buffers. Usually 4 (=16 Rx buffers) is a good value. (Andreas Neuhaus)
45 * Decreased to 2 (=4 Rx buffers) (Ken Yap, 20010305) */
46
47 #define LANCE_LOG_RX_BUFFERS 2 /* Use 2^2=4 Rx buffers */
48
49 #define RX_RING_SIZE (1 << (LANCE_LOG_RX_BUFFERS))
50 #define RX_RING_MOD_MASK (RX_RING_SIZE - 1)
51 #define RX_RING_LEN_BITS ((LANCE_LOG_RX_BUFFERS) << 29)
52
53 struct lance_init_block
54 {
55 unsigned short mode;
56 unsigned char phys_addr[ETH_ALEN];
57 unsigned long filter[2];
58 Address rx_ring;
59 Address tx_ring;
60 };
61
62 struct lance_rx_head
63 {
64 union {
65 Address base;
66 unsigned char addr[4];
67 } u;
68 short buf_length; /* 2s complement */
69 short msg_length;
70 };
71
72 struct lance_tx_head
73 {
74 union {
75 Address base;
76 unsigned char addr[4];
77 } u;
78 short buf_length; /* 2s complement */
79 short misc;
80 };
81
82 struct lance_interface
83 {
84 struct lance_init_block init_block;
85 struct lance_rx_head rx_ring[RX_RING_SIZE];
86 struct lance_tx_head tx_ring;
87 unsigned char rbuf[RX_RING_SIZE][ETH_FRAME_LEN+4];
88 unsigned char tbuf[ETH_FRAME_LEN];
89 /*
90 * Do not alter the order of the struct members above;
91 * the hardware depends on the correct alignment.
92 */
93 int rx_idx;
94 };
95
96 #define LANCE_MUST_PAD 0x00000001
97 #define LANCE_ENABLE_AUTOSELECT 0x00000002
98 #define LANCE_SELECT_PHONELINE 0x00000004
99 #define LANCE_MUST_UNRESET 0x00000008
100
101 /* A mapping from the chip ID number to the part number and features.
102 These are from the datasheets -- in real life the '970 version
103 reportedly has the same ID as the '965. */
104 static const struct lance_chip_type
105 {
106 int id_number;
107 const char *name;
108 int flags;
109 } chip_table[] = {
110 {0x0000, "LANCE 7990", /* Ancient lance chip. */
111 LANCE_MUST_PAD + LANCE_MUST_UNRESET},
112 {0x0003, "PCnet/ISA 79C960", /* 79C960 PCnet/ISA. */
113 LANCE_ENABLE_AUTOSELECT},
114 {0x2260, "PCnet/ISA+ 79C961", /* 79C961 PCnet/ISA+, Plug-n-Play. */
115 LANCE_ENABLE_AUTOSELECT},
116 {0x2420, "PCnet/PCI 79C970", /* 79C970 or 79C974 PCnet-SCSI, PCI. */
117 LANCE_ENABLE_AUTOSELECT},
118 /* Bug: the PCnet/PCI actually uses the PCnet/VLB ID number, so just call
119 it the PCnet32. */
120 {0x2430, "PCnet32", /* 79C965 PCnet for VL bus. */
121 LANCE_ENABLE_AUTOSELECT},
122 {0x2621, "PCnet/PCI-II 79C970A", /* 79C970A PCInetPCI II. */
123 LANCE_ENABLE_AUTOSELECT},
124 {0x2625, "PCnet-FAST III 79C973", /* 79C973 PCInet-FAST III. */
125 LANCE_ENABLE_AUTOSELECT},
126 {0x2626, "PCnet/HomePNA 79C978",
127 LANCE_ENABLE_AUTOSELECT|LANCE_SELECT_PHONELINE},
128 {0x0, "PCnet (unknown)",
129 LANCE_ENABLE_AUTOSELECT},
130 };
131
132 /* Define a macro for converting program addresses to real addresses */
133 #undef virt_to_bus
134 #define virt_to_bus(x) ((unsigned long)x)
135
136 static int chip_version;
137 static int lance_version;
138 static unsigned short ioaddr;
139 #ifndef INCLUDE_LANCE
140 static int dma;
141 #endif
142 static struct lance_interface *lp;
143
144 /* additional 8 bytes for 8-byte alignment space */
145 #ifdef USE_LOWMEM_BUFFER
146 #define lance ((char *)0x10000 - (sizeof(struct lance_interface)+8))
147 #else
148 static char lance[sizeof(struct lance_interface)+8];
149 #endif
150
151 #ifndef INCLUDE_LANCE
152 /* DMA defines and helper routines */
153
154 /* DMA controller registers */
155 #define DMA1_CMD_REG 0x08 /* command register (w) */
156 #define DMA1_STAT_REG 0x08 /* status register (r) */
157 #define DMA1_REQ_REG 0x09 /* request register (w) */
158 #define DMA1_MASK_REG 0x0A /* single-channel mask (w) */
159 #define DMA1_MODE_REG 0x0B /* mode register (w) */
160 #define DMA1_CLEAR_FF_REG 0x0C /* clear pointer flip-flop (w) */
161 #define DMA1_TEMP_REG 0x0D /* Temporary Register (r) */
162 #define DMA1_RESET_REG 0x0D /* Master Clear (w) */
163 #define DMA1_CLR_MASK_REG 0x0E /* Clear Mask */
164 #define DMA1_MASK_ALL_REG 0x0F /* all-channels mask (w) */
165
166 #define DMA2_CMD_REG 0xD0 /* command register (w) */
167 #define DMA2_STAT_REG 0xD0 /* status register (r) */
168 #define DMA2_REQ_REG 0xD2 /* request register (w) */
169 #define DMA2_MASK_REG 0xD4 /* single-channel mask (w) */
170 #define DMA2_MODE_REG 0xD6 /* mode register (w) */
171 #define DMA2_CLEAR_FF_REG 0xD8 /* clear pointer flip-flop (w) */
172 #define DMA2_TEMP_REG 0xDA /* Temporary Register (r) */
173 #define DMA2_RESET_REG 0xDA /* Master Clear (w) */
174 #define DMA2_CLR_MASK_REG 0xDC /* Clear Mask */
175 #define DMA2_MASK_ALL_REG 0xDE /* all-channels mask (w) */
176
177
178 #define DMA_MODE_READ 0x44 /* I/O to memory, no autoinit, increment, single mode */
179 #define DMA_MODE_WRITE 0x48 /* memory to I/O, no autoinit, increment, single mode */
180 #define DMA_MODE_CASCADE 0xC0 /* pass thru DREQ->HRQ, DACK<-HLDA only */
181
182 /* enable/disable a specific DMA channel */
enable_dma(unsigned int dmanr)183 static void enable_dma(unsigned int dmanr)
184 {
185 if (dmanr <= 3)
186 outb_p(dmanr, DMA1_MASK_REG);
187 else
188 outb_p(dmanr & 3, DMA2_MASK_REG);
189 }
190
disable_dma(unsigned int dmanr)191 static void disable_dma(unsigned int dmanr)
192 {
193 if (dmanr <= 3)
194 outb_p(dmanr | 4, DMA1_MASK_REG);
195 else
196 outb_p((dmanr & 3) | 4, DMA2_MASK_REG);
197 }
198
199 /* set mode (above) for a specific DMA channel */
set_dma_mode(unsigned int dmanr,char mode)200 static void set_dma_mode(unsigned int dmanr, char mode)
201 {
202 if (dmanr <= 3)
203 outb_p(mode | dmanr, DMA1_MODE_REG);
204 else
205 outb_p(mode | (dmanr&3), DMA2_MODE_REG);
206 }
207 #endif /* !INCLUDE_LANCE */
208
209 /**************************************************************************
210 RESET - Reset adapter
211 ***************************************************************************/
lance_reset(struct nic * nic)212 static void lance_reset(struct nic *nic)
213 {
214 int i;
215 Address l;
216
217 /* Reset the LANCE */
218 (void)inw(ioaddr+LANCE_RESET);
219 /* Un-Reset the LANCE, needed only for the NE2100 */
220 if (chip_table[lance_version].flags & LANCE_MUST_UNRESET)
221 outw(0, ioaddr+LANCE_RESET);
222 if (chip_table[lance_version].flags & LANCE_ENABLE_AUTOSELECT)
223 {
224 /* This is 79C960 specific; Turn on auto-select of media
225 (AUI, BNC). */
226 outw(0x2, ioaddr+LANCE_ADDR);
227 /* Don't touch 10base2 power bit. */
228 outw(inw(ioaddr+LANCE_BUS_IF) | 0x2, ioaddr+LANCE_BUS_IF);
229 }
230 /* HomePNA cards need to explicitly pick the phoneline interface.
231 * Some of these cards have ethernet interfaces as well, this
232 * code might require some modification for those.
233 */
234 if (chip_table[lance_version].flags & LANCE_SELECT_PHONELINE) {
235 short media, check ;
236 /* this is specific to HomePNA cards... */
237 outw(49, ioaddr+0x12) ;
238 media = inw(ioaddr+0x16) ;
239 #ifdef DEBUG
240 printf("media was %d\n", media) ;
241 #endif
242 media &= ~3 ;
243 media |= 1 ;
244 #ifdef DEBUG
245 printf("media changed to %d\n", media) ;
246 #endif
247 media &= ~3 ;
248 media |= 1 ;
249 outw(49, ioaddr+0x12) ;
250 outw(media, ioaddr+0x16) ;
251 outw(49, ioaddr+0x12) ;
252 check = inw(ioaddr+0x16) ;
253 #ifdef DEBUG
254 printf("check %s, media was set properly\n",
255 check == media ? "passed" : "FAILED" ) ;
256 #endif
257 }
258
259 /* Re-initialise the LANCE, and start it when done. */
260 /* Set station address */
261 for (i = 0; i < ETH_ALEN; ++i)
262 lp->init_block.phys_addr[i] = nic->node_addr[i];
263 /* Preset the receive ring headers */
264 for (i=0; i<RX_RING_SIZE; i++) {
265 lp->rx_ring[i].buf_length = -ETH_FRAME_LEN-4;
266 /* OWN */
267 lp->rx_ring[i].u.base = virt_to_bus(lp->rbuf[i]) & 0xffffff;
268 /* we set the top byte as the very last thing */
269 lp->rx_ring[i].u.addr[3] = 0x80;
270 }
271 lp->rx_idx = 0;
272 lp->init_block.mode = 0x0; /* enable Rx and Tx */
273 l = (Address)virt_to_bus(&lp->init_block);
274 outw(0x1, ioaddr+LANCE_ADDR);
275 (void)inw(ioaddr+LANCE_ADDR);
276 outw((short)l, ioaddr+LANCE_DATA);
277 outw(0x2, ioaddr+LANCE_ADDR);
278 (void)inw(ioaddr+LANCE_ADDR);
279 outw((short)(l >> 16), ioaddr+LANCE_DATA);
280 outw(0x4, ioaddr+LANCE_ADDR);
281 (void)inw(ioaddr+LANCE_ADDR);
282 outw(0x915, ioaddr+LANCE_DATA);
283 outw(0x0, ioaddr+LANCE_ADDR);
284 (void)inw(ioaddr+LANCE_ADDR);
285 outw(0x4, ioaddr+LANCE_DATA); /* stop */
286 outw(0x1, ioaddr+LANCE_DATA); /* init */
287 for (i = 10000; i > 0; --i)
288 if (inw(ioaddr+LANCE_DATA) & 0x100)
289 break;
290 #ifdef DEBUG
291 if (i <= 0)
292 printf("Init timed out\n");
293 #endif
294 /* Apparently clearing the InitDone bit here triggers a bug
295 in the '974. (Mark Stockton) */
296 outw(0x2, ioaddr+LANCE_DATA); /* start */
297 }
298
299 /**************************************************************************
300 POLL - Wait for a frame
301 ***************************************************************************/
lance_poll(struct nic * nic)302 static int lance_poll(struct nic *nic)
303 {
304 int status;
305
306 status = lp->rx_ring[lp->rx_idx].u.base >> 24;
307 if (status & 0x80)
308 return (0);
309 #ifdef DEBUG
310 printf("LANCE packet received rx_ring.u.base %X mcnt %hX csr0 %hX\n",
311 lp->rx_ring[lp->rx_idx].u.base, lp->rx_ring[lp->rx_idx].msg_length,
312 inw(ioaddr+LANCE_DATA));
313 #endif
314 if (status == 0x3)
315 memcpy(nic->packet, lp->rbuf[lp->rx_idx], nic->packetlen = lp->rx_ring[lp->rx_idx].msg_length);
316 /* Andrew Boyd of QNX reports that some revs of the 79C765
317 clear the buffer length */
318 lp->rx_ring[lp->rx_idx].buf_length = -ETH_FRAME_LEN-4;
319 lp->rx_ring[lp->rx_idx].u.addr[3] |= 0x80; /* prime for next receive */
320
321 /* I'm not sure if the following is still ok with multiple Rx buffers, but it works */
322 outw(0x0, ioaddr+LANCE_ADDR);
323 (void)inw(ioaddr+LANCE_ADDR);
324 outw(0x500, ioaddr+LANCE_DATA); /* clear receive + InitDone */
325
326 /* Switch to the next Rx ring buffer */
327 lp->rx_idx = (lp->rx_idx + 1) & RX_RING_MOD_MASK;
328
329 return (status == 0x3);
330 }
331
332 /**************************************************************************
333 TRANSMIT - Transmit a frame
334 ***************************************************************************/
lance_transmit(struct nic * nic,const char * d,unsigned int t,unsigned int s,const char * p)335 static void lance_transmit(
336 struct nic *nic,
337 const char *d, /* Destination */
338 unsigned int t, /* Type */
339 unsigned int s, /* size */
340 const char *p) /* Packet */
341 {
342 unsigned long time;
343
344 /* copy the packet to ring buffer */
345 memcpy(lp->tbuf, d, ETH_ALEN); /* dst */
346 memcpy(&lp->tbuf[ETH_ALEN], nic->node_addr, ETH_ALEN); /* src */
347 lp->tbuf[ETH_ALEN+ETH_ALEN] = t >> 8; /* type */
348 lp->tbuf[ETH_ALEN+ETH_ALEN+1] = t; /* type */
349 memcpy(&lp->tbuf[ETH_HLEN], p, s);
350 s += ETH_HLEN;
351 if (chip_table[chip_version].flags & LANCE_MUST_PAD)
352 while (s < ETH_ZLEN) /* pad to min length */
353 lp->tbuf[s++] = 0;
354 lp->tx_ring.buf_length = -s;
355 lp->tx_ring.misc = 0x0;
356 /* OWN, STP, ENP */
357 lp->tx_ring.u.base = virt_to_bus(lp->tbuf) & 0xffffff;
358 /* we set the top byte as the very last thing */
359 lp->tx_ring.u.addr[3] = 0x83;
360 /* Trigger an immediate send poll */
361 outw(0x0, ioaddr+LANCE_ADDR);
362 (void)inw(ioaddr+LANCE_ADDR); /* as in the datasheets... */
363 /* Klaus Espenlaub: the value below was 0x48, but that enabled the
364 * interrupt line, causing a hang if for some reasone the interrupt
365 * controller had the LANCE interrupt enabled. I have no idea why
366 * nobody ran into this before... */
367 outw(0x08, ioaddr+LANCE_DATA);
368 /* wait for transmit complete */
369 time = currticks() + TICKS_PER_SEC; /* wait one second */
370 while (currticks() < time && (lp->tx_ring.u.base & 0x80000000) != 0)
371 ;
372 if ((lp->tx_ring.u.base & 0x80000000) != 0)
373 printf("LANCE timed out on transmit\n");
374 (void)inw(ioaddr+LANCE_ADDR);
375 outw(0x200, ioaddr+LANCE_DATA); /* clear transmit + InitDone */
376 #ifdef DEBUG
377 printf("tx_ring.u.base %X tx_ring.buf_length %hX tx_ring.misc %hX csr0 %hX\n",
378 lp->tx_ring.u.base, lp->tx_ring.buf_length, lp->tx_ring.misc,
379 inw(ioaddr+LANCE_DATA));
380 #endif
381 }
382
lance_disable(struct nic * nic)383 static void lance_disable(struct nic *nic)
384 {
385 (void)inw(ioaddr+LANCE_RESET);
386 if (chip_table[lance_version].flags & LANCE_MUST_UNRESET)
387 outw(0, ioaddr+LANCE_RESET);
388
389 outw(0, ioaddr+LANCE_ADDR);
390 outw(0x0004, ioaddr+LANCE_DATA); /* stop the LANCE */
391
392 #ifndef INCLUDE_LANCE
393 disable_dma(dma);
394 #endif
395 }
396
397 #ifdef INCLUDE_LANCE
lance_probe1(struct nic * nic,struct pci_device * pci)398 static int lance_probe1(struct nic *nic, struct pci_device *pci)
399 #else
400 static int lance_probe1(struct nic *nic)
401 #endif
402 {
403 int reset_val ;
404 unsigned int i;
405 Address l;
406 short dma_channels;
407 #ifndef INCLUDE_LANCE
408 static const char dmas[] = { 5, 6, 7, 3 };
409 #endif
410
411 reset_val = inw(ioaddr+LANCE_RESET);
412 outw(reset_val, ioaddr+LANCE_RESET);
413 #if 1 /* Klaus Espenlaub -- was #ifdef INCLUDE_NE2100*/
414 outw(0x0, ioaddr+LANCE_ADDR); /* Switch to window 0 */
415 if (inw(ioaddr+LANCE_DATA) != 0x4)
416 return (-1);
417 #endif
418 outw(88, ioaddr+LANCE_ADDR); /* Get the version of the chip */
419 if (inw(ioaddr+LANCE_ADDR) != 88)
420 lance_version = 0;
421 else
422 {
423 chip_version = inw(ioaddr+LANCE_DATA);
424 outw(89, ioaddr+LANCE_ADDR);
425 chip_version |= inw(ioaddr+LANCE_DATA) << 16;
426 if ((chip_version & 0xfff) != 0x3)
427 return (-1);
428 chip_version = (chip_version >> 12) & 0xffff;
429 for (lance_version = 1; chip_table[lance_version].id_number != 0; ++lance_version)
430 if (chip_table[lance_version].id_number == chip_version)
431 break;
432 }
433 /* make sure data structure is 8-byte aligned */
434 l = ((Address)lance + 7) & ~7;
435 lp = (struct lance_interface *)l;
436 lp->init_block.mode = 0x3; /* disable Rx and Tx */
437 lp->init_block.filter[0] = lp->init_block.filter[1] = 0x0;
438 /* using multiple Rx buffer and a single Tx buffer */
439 lp->init_block.rx_ring = (virt_to_bus(&lp->rx_ring) & 0xffffff) | RX_RING_LEN_BITS;
440 lp->init_block.tx_ring = virt_to_bus(&lp->tx_ring) & 0xffffff;
441 l = virt_to_bus(&lp->init_block);
442 outw(0x1, ioaddr+LANCE_ADDR);
443 (void)inw(ioaddr+LANCE_ADDR);
444 outw((unsigned short)l, ioaddr+LANCE_DATA);
445 outw(0x2, ioaddr+LANCE_ADDR);
446 (void)inw(ioaddr+LANCE_ADDR);
447 outw((unsigned short)(l >> 16), ioaddr+LANCE_DATA);
448 outw(0x4, ioaddr+LANCE_ADDR);
449 (void)inw(ioaddr+LANCE_ADDR);
450 outw(0x915, ioaddr+LANCE_DATA);
451 outw(0x0, ioaddr+LANCE_ADDR);
452 (void)inw(ioaddr+LANCE_ADDR);
453 /* Get station address */
454 for (i = 0; i < ETH_ALEN; ++i) {
455 nic->node_addr[i] = inb(ioaddr+LANCE_ETH_ADDR+i);
456 }
457 #ifndef INCLUDE_LANCE
458 /* now probe for DMA channel */
459 dma_channels = ((inb(DMA1_STAT_REG) >> 4) & 0xf) |
460 (inb(DMA2_STAT_REG) & 0xf0);
461 /* need to fix when PCI provides DMA info */
462 for (i = 0; i < (sizeof(dmas)/sizeof(dmas[0])); ++i)
463 {
464 int j;
465
466 dma = dmas[i];
467 /* Don't enable a permanently busy DMA channel,
468 or the machine will hang */
469 if (dma_channels & (1 << dma))
470 continue;
471 outw(0x7f04, ioaddr+LANCE_DATA); /* clear memory error bits */
472 set_dma_mode(dma, DMA_MODE_CASCADE);
473 enable_dma(dma);
474 outw(0x1, ioaddr+LANCE_DATA); /* init */
475 for (j = 100; j > 0; --j)
476 if (inw(ioaddr+LANCE_DATA) & 0x900)
477 break;
478 if (inw(ioaddr+LANCE_DATA) & 0x100)
479 break;
480 else
481 disable_dma(dma);
482 }
483 if (i >= (sizeof(dmas)/sizeof(dmas[0])))
484 dma = 0;
485 printf("\n%s base %#X, DMA %d, addr %!\n",
486 chip_table[lance_version].name, ioaddr, dma, nic->node_addr);
487 #else
488 printf(" %s base %#hX, addr %!\n", chip_table[lance_version].name, ioaddr, nic->node_addr);
489 #endif
490 if (chip_table[chip_version].flags & LANCE_ENABLE_AUTOSELECT) {
491 /* Turn on auto-select of media (10baseT or BNC) so that the
492 * user watch the LEDs. */
493 outw(0x0002, ioaddr+LANCE_ADDR);
494 /* Don't touch 10base2 power bit. */
495 outw(inw(ioaddr+LANCE_BUS_IF) | 0x0002, ioaddr+LANCE_BUS_IF);
496 }
497 return (lance_version);
498 }
499
500 /**************************************************************************
501 PROBE - Look for an adapter, this routine's visible to the outside
502 ***************************************************************************/
503
504 #ifdef INCLUDE_LANCE
lancepci_probe(struct nic * nic,unsigned short * probe_addrs,struct pci_device * pci)505 struct nic *lancepci_probe(struct nic *nic, unsigned short *probe_addrs, struct pci_device *pci)
506 #endif
507 #ifdef INCLUDE_NE2100
508 struct nic *ne2100_probe(struct nic *nic, unsigned short *probe_addrs)
509 #endif
510 #ifdef INCLUDE_NI6510
511 struct nic *ni6510_probe(struct nic *nic, unsigned short *probe_addrs)
512 #endif
513 {
514 unsigned short *p;
515 #ifndef INCLUDE_LANCE
516 static unsigned short io_addrs[] = { 0x300, 0x320, 0x340, 0x360, 0 };
517 #endif
518
519 /* if probe_addrs is 0, then routine can use a hardwired default */
520 if (probe_addrs == 0) {
521 #ifdef INCLUDE_LANCE
522 return 0;
523 #else
524 probe_addrs = io_addrs;
525 #endif
526 }
527 for (p = probe_addrs; (ioaddr = *p) != 0; ++p)
528 {
529 char offset15, offset14 = inb(ioaddr + 14);
530 unsigned short pci_cmd;
531
532 #ifdef INCLUDE_NE2100
533 if ((offset14 == 0x52 || offset14 == 0x57) &&
534 ((offset15 = inb(ioaddr + 15)) == 0x57 || offset15 == 0x44))
535 if (lance_probe1(nic) >= 0)
536 break;
537 #endif
538 #ifdef INCLUDE_NI6510
539 if ((offset14 == 0x00 || offset14 == 0x52) &&
540 ((offset15 = inb(ioaddr + 15)) == 0x55 || offset15 == 0x44))
541 if (lance_probe1(nic) >= 0)
542 break;
543 #endif
544 #ifdef INCLUDE_LANCE
545 adjust_pci_device(pci);
546 if (lance_probe1(nic, pci) >= 0)
547 break;
548 #endif
549 }
550 /* if board found */
551 if (ioaddr != 0)
552 {
553 /* point to NIC specific routines */
554 lance_reset(nic);
555 nic->reset = lance_reset;
556 nic->poll = lance_poll;
557 nic->transmit = lance_transmit;
558 nic->disable = lance_disable;
559 return nic;
560 }
561
562 /* no board found */
563 return 0;
564 }
565