## this file is used by NFC stack (external/libnfc-nci/src)
## and NFC Service Java Native Interface (packages/apps/Nfc/nci/jni)

###############################################################################
# Application options
APPL_TRACE_LEVEL=0xFF
PROTOCOL_TRACE_LEVEL=0xFFFFFFFF

###############################################################################
# File used for NFA storage
NFA_STORAGE="/data/nfc"

###############################################################################
# Force tag polling for the following technology(s).
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B |
#            NFA_TECHNOLOGY_MASK_F | NFA_TECHNOLOGY_MASK_ISO15693 |
#            NFA_TECHNOLOGY_MASK_B_PRIME | NFA_TECHNOLOGY_MASK_A_ACTIVE |
#            NFA_TECHNOLOGY_MASK_F_ACTIVE.
#
# Notable bits:
#   NFA_TECHNOLOGY_MASK_KOVIO       0x20
#   NFA_TECHNOLOGY_MASK_A_ACTIVE    0x40
#   NFA_TECHNOLOGY_MASK_F_ACTIVE    0x80
#POLLING_TECH_MASK=0xDF

###############################################################################
# Force P2P to only listen for the following technology(s).
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_F |
#            NFA_TECHNOLOGY_MASK_A_ACTIVE | NFA_TECHNOLOGY_MASK_F_ACTIVE
P2P_LISTEN_TECH_MASK=0x45

###############################################################################
# This setting allows you to disable registering the T4t Virtual SE that causes
# the NFCC to send PPSE requests to the DH.
# The default setting is enabled (i.e. T4t Virtual SE is registered).
#REGISTER_VIRTUAL_SE=1

###############################################################################
# Use Nexus S NXP RC work to allow our stack/firmware to work with a retail
# Nexus S that causes IOP issues.  Note, this will not pass conformance and
# should be removed for production.
USE_NXP_P2P_RC_WORKAROUND=1

###############################################################################
# When screen is turned off, specify the desired power state of the controller.
# 0: power-off-sleep state; DEFAULT
# 1: full-power state
# 2: screen-off card-emulation (CE4/CE3/CE1 modes are used)
#SCREEN_OFF_POWER_STATE=0

###############################################################################
# Configure the default Destination Gate used by HCI (the default is 4, which
# is the ETSI loopback gate.
#NFA_HCI_DEFAULT_DEST_GATE=4

###############################################################################
# Configure the single default SE to use.  The default is to use the first
# SE that is detected by the stack.  This value might be used when the phone
# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use
# one of them (e.g. 0xF4).
#ACTIVE_SE=0xF3

###############################################################################
# Configure the NFC Extras to open and use a static pipe.  If the value is
# not set or set to 0, then the default is use a dynamic pipe based on a
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE).  Note there is a value
# for each UICC (where F3="UICC0" and F4="UICC1")
#NFA_HCI_STATIC_PIPE_ID_F3=0x70
#NFA_HCI_STATIC_PIPE_ID_F4=0x71

###############################################################################
# Force UICC to only listen to the following technology(s).
# The bits are defined as tNFA_TECHNOLOGY_MASK in nfa_api.h.
# Default is NFA_TECHNOLOGY_MASK_A | NFA_TECHNOLOGY_MASK_B.
#UICC_LISTEN_TECH_MASK=0x03

###############################################################################
# When disconnecting from Oberthur secure element, perform a warm-reset of
# the secure element to deselect the applet.
# The default hex value of the command is 0x3.  If this variable is undefined, then
# this feature is not used.
#OBERTHUR_WARM_RESET_COMMAND=3

###############################################################################
# Default poll duration (in ms)
#  The defualt is 500ms if not set (see nfc_target.h)
NFA_DM_DISC_DURATION_POLL=333

###############################################################################
# AID for Empty Select command
# If specified, this AID will be substituted when an Empty SELECT command is
# detected.  The first byte is the length of the AID.  Maximum length is 16.
AID_FOR_EMPTY_SELECT={08:A0:00:00:01:51:00:00:00}