# INI Generator version 1.4; Aligned to TS version 6.1.2.0.27 #------------------------------------------------------------------------------------------------------------------------------------------------------------ # SECTION 1: Non FEM-dependant section #------------------------------------------------------------------------------------------------------------------------------------------------------------ #------------------------------------------------------------------------------------------------------------------------------------------------------------ # SECTION 1.1: General parameters #------------------------------------------------------------------------------------------------------------------------------------------------------------ TXBiPFEMAutoDetect = 00 # Length: 1; Unit: Options (0: Manual Mode, 1: Automatic mode); Format: Unsigned; Source: Customer; Comment: This parameter is used by the FW to decide if the front-end is determined automatically or manually TXBiPFEMManufacturer = 01 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit1,0: used to determine which FEM vendor type is used on the platform (0: RFMD, 1: TQS, 2:SKW, 3:HP), Bit3,2: unused, Bit7-4:External/internal load (4-SKW SB, 5-SKW HB, 6-HP SB, 7-HP HB) RefClk = 02 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit 0,1,2-0:19.2MHz,1:26MHz,2:38.4MHz[Default],3:52MHz,4:38.4MHz XTAL,5:26MHz XTAL, Bit 3-CLK_REQ type, 0=wired-OR, 1=push-pull, Bit 4-CLK_REQ polarity SettlingTime = 05 # Length: 1; Unit: ms (0-15); Format: Unsigned; Source: Customer; Comment: The time from asserting CLK_REQ (low to high) to valid FREF clock on the device inputs ClockValidOnWakeup = 00 # Length: 1; Unit: Options (0: Reference clock not valid, 1: Reference clock is valid and stable); Format: Unsigned; Source: Customer; Comment: This parameter indicates whether the FREF clock is valid on wakeup DC2DCMode = 00 # Length: 1; Unit: Bit_Options; Format: Unsigned, Source: Customer; Comment: Bit0 - DC2DC mode (0: btSPI is not used;1: btSPI used mux DC2DC to BT_FUNC2), Bit1- Level shifter support (0: No LS, 1: With LS) Single_Dual_Band_Solution = 01 # Length: 1; Unit: Options (0: Single band, 1: Dual band); Format: Unsigned; Source: Customer; Comment: This parameter indicates if the solution is single band (2.4GHz only) or dual band (2.4GHz & 5GHz) Settings = 01 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit0-NBI(0:Off,1:On),Bit1-Telec ch14(0:Off,1:On),Bit2-FEM0-LB,Bit3-FEM0-HB,Bit4-FEM1-LB,Bit5-FEM1-HB-TX BiP load(0:Int.,1:Ext.),Bit6-LPD LB,Bit7-LPD HB SRState = 00 # Length: 1; Unit: Options (0: Disabled, 1: Enabled); Format: Decimal; Source: TI; Comment: Smart Reflax (proprietary mechanism of TI that identify the silicon process specific params) state SRF1 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 0F 3F # Length: 16; Unit: SRF1 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism SRF2 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00 # Length: 16; Unit: SRF2 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism SRF3 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00 # Length: 16; Unit: SRF3 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism #SR_Debug_Table = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00 # Length: 16; Unit: SR_Debug_Table values; Format: Signed; Source: TI; Comment: SR Debug values – for TI internal use only #SR_SEN_N_P = 22 # Length: 1; Unit: SR_SEN_N_P values; Format: Unsigned; Source: TI; Comment: SR Debug values – for TI internal use only #SR_SEN_N_P_Gain = a9 # Length: 1; Unit: SR_SEN_N_P_GAIN values; Format: Unsigned; Source: TI; Comment: SR Debug values – for TI internal use only #SR_SEN_NRN = c1 # Length: 1; Unit: SR_SEN_NRN values; Format: Unsigned; Source: TI ; Comment: SR Debug values – for TI internal use only #SR_SEN_PRN = 8d # Length: 1; Unit: SR_SEN_PRN values; Format: Unsigned; Source: TI ; Comment: SR Debug values – for TI internal use only #------------------------------------------------------------------------------------------------------------------------------------------------------------ # SECTION 1.2: Band-dependant parameters #------------------------------------------------------------------------------------------------------------------------------------------------------------ #------------------------------------------------------------------------------------------------------------------------------------------------------------ # SECTION 1.2.1: 2.4G parameters #------------------------------------------------------------------------------------------------------------------------------------------------------------ RxTraceInsertionLoss_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter indicates the printed circuit board (PCB) trace insertion loss TXTraceLoss_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter is used to align the output power to a different location on the board RxRssiAndProcessCompensation_2_4G = EC F6 00 0C 18 F8 FC 00 08 10 F0 F8 00 0A 14 # Length: 15; Unit: 1/8dB; Format: Signed; Source: TI; Comment: The RSSI corner points are determined during RSSI temperature and process characterization #------------------------------------------------------------------------------------------------------------------------------------------------------------ # SECTION 1.2.2: 5G parameters #------------------------------------------------------------------------------------------------------------------------------------------------------------ RxTraceInsertionLoss_5G = 00 00 00 00 00 00 00 # Length: 7; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter indicates the printed circuit board (PCB) trace insertion loss TXTraceLoss_5G = 00 00 00 00 00 00 00 # Length: 7; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter is used to align the output power to a different location on the board RxRssiAndProcessCompensation_5G = EE F4 F8 FE 05 EA F3 FA 01 06 E5 F1 FA 02 07 # Length: 15; Unit: 1/8dB; Format: Signed; Source: TI; Comment: The RSSI corner points are determined during RSSI temperature and process characterization #------------------------------------------------------------------------------------------------------------------------------------------------------------ # SECTION 2: FEM-dependant section #------------------------------------------------------------------------------------------------------------------------------------------------------------ #------------------------------------------------------------------------------------------------------------------------------------------------------------ # SECTION 2.1: FEM parameters #------------------------------------------------------------------------------------------------------------------------------------------------------------ # #------------------------------------------------------------------------------------------------------------------------------------------------------------ # SECTION 2.1.1: 2.4G parameters #------------------------------------------------------------------------------------------------------------------------------------------------------------ FEM1_TXBiPReferencePDvoltage_2_4G = 01D9 # Length: 1; Unit: 1mV; Format: Unsigned; Source: TI; Comment: This parameter define the reference point of the FEM power detector FEM1_TxBiPReferencePower_2_4G = 80 # Length: 1; Unit: 1/8dB; Format: Signed; Source: TI; Comment: Reference output power that produces given reference power detector output voltage . FEM1_TxBiPOffsetdB_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Signed; Source: Customer; Comment: This field is used to fine-tune the TX BiP by the customer FEM1_TxPerRatePowerLimits_2_4G_Normal = 1D 1F 22 26 27 29 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_TxPerRatePowerLimits_2_4G_Degraded = 1D 1F 22 26 27 27 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_TxPerRatePowerLimits_2_4G_Extreme = 16 1D 1E 20 24 25 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_DegradedLowToNormalThr_2_4G = 1E # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_NormalToDegradedHighThr_2_4G = 2D # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_TxPerChannelPowerLimits_2_4G_11b = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels FEM1_TxPerChannelPowerLimits_2_4G_OFDM = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels FEM1_TxPDVsRateOffsets_2_4G = 01 02 02 02 02 00 # Length: 6; Unit: 1/8dB; Format: Signed; Source: TI; Comment: This parameter is a power detector offset value used to correct the power detector curve for each rate group FEM1_TxIbiasTable_2_4G = 15 15 15 19 19 15 # Length: 6; Unit: Codeword ; Format: Unsigned; Source: TI; Comment: This parameter sets the bias current provided by the SoC to the PA in the FEM. Options (MCS7, 54/48, 36/24, 18/12, 9/6, 11b) FEM1_RxFemInsertionLoss_2_4G = 10 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: TI; Comment: This parameter specifies the received insertion loss of the WL127x #------------------------------------------------------------------------------------------------------------------------------------------------------------ # SECTION 2.1.2: 5G parameters #------------------------------------------------------------------------------------------------------------------------------------------------------------ FEM1_TXBiPReferencePDvoltage_5G = 019A 01AE 01C2 01CC 01DB 01DB 01D1 # Length: 7; Unit: 1mV; Format: Unsigned; Source: TI; Comment: This parameter define the reference point of the FEM power detector FEM1_TxBiPReferencePower_5G = 80 80 80 80 80 80 80 # Length: 7; Unit: 1/8dB; Format: Signed; Source: TI; Comment: Reference output power that produces given reference power detector output voltage . FEM1_TxBiPOffsetdB_5G = 00 00 00 00 00 00 00 # Length: 7; Unit: 1/8dB; Format: Signed; Source: Customer; Comment: This field is used to fine-tune the TX BiP by the customer FEM1_TxPerRatePowerLimits_5G_Normal = 1C 1E 21 23 25 50 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_TxPerRatePowerLimits_5G_Degraded = 18 1E 21 23 25 50 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_TxPerRatePowerLimits_5G_Extreme = 16 1C 1E 20 20 50 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_DegradedLowToNormalThr_5G = 1E # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_NormalToDegradedHighThr_5G = 2D # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating FEM1_TxPerChannelPowerLimits_5G_OFDM = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 35; Unit: 1/2dB; Format: Signed; Source: Customer; FEM1_TxPDVsRateOffsets_5G = 01 02 02 02 02 00 # Length: 7; Unit: 1/8dB; Format: Signed; Source: TI; Comment: This parameter is a power detector offset value used to correct the power detector curve for each rate group FEM1_TxIbiasTable_5G = 10 10 10 10 10 10 # Length: 6; Unit: Codeword; Format: Unsigned; Source: TI; Comment: This parameter sets the bias current provided by the SoC to the PA in the FEM FEM1_RxFemInsertionLoss_5G = 10 10 10 10 10 10 10 # Length: 7; Unit: 1/8dB; Format: Unsigned; Source: TI; Comment: This parameter specifies the received insertion loss of the WL127x