1 /****************************************************************************** 2 * 3 * Copyright (C) 2003-2014 Broadcom Corporation 4 * 5 * Licensed under the Apache License, Version 2.0 (the "License"); 6 * you may not use this file except in compliance with the License. 7 * You may obtain a copy of the License at: 8 * 9 * http://www.apache.org/licenses/LICENSE-2.0 10 * 11 * Unless required by applicable law or agreed to in writing, software 12 * distributed under the License is distributed on an "AS IS" BASIS, 13 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. 14 * See the License for the specific language governing permissions and 15 * limitations under the License. 16 * 17 ******************************************************************************/ 18 19 /****************************************************************************** 20 * 21 * This is the public interface file for BTA, Broadcom's Bluetooth 22 * application layer for mobile phones. 23 * 24 ******************************************************************************/ 25 #ifndef BTA_API_H 26 #define BTA_API_H 27 28 #include "data_types.h" 29 #include "bt_target.h" 30 #include "bt_types.h" 31 #include "btm_api.h" 32 #include "uipc_msg.h" 33 34 #if BLE_INCLUDED == TRUE 35 #include "btm_ble_api.h" 36 #endif 37 38 /***************************************************************************** 39 ** Constants and data types 40 *****************************************************************************/ 41 42 /* Status Return Value */ 43 #define BTA_SUCCESS 0 /* Successful operation. */ 44 #define BTA_FAILURE 1 /* Generic failure. */ 45 #define BTA_PENDING 2 /* API cannot be completed right now */ 46 #define BTA_BUSY 3 47 #define BTA_NO_RESOURCES 4 48 #define BTA_WRONG_MODE 5 49 50 typedef UINT8 tBTA_STATUS; 51 52 /* 53 * Service ID 54 * 55 * NOTES: When you add a new Service ID for BTA AND require to change the value of BTA_MAX_SERVICE_ID, 56 * make sure that the correct security ID of the new service from Security service definitions (btm_api.h) 57 * should be added to bta_service_id_to_btm_srv_id_lkup_tbl table in bta_dm_act.c. 58 */ 59 60 #define BTA_RES_SERVICE_ID 0 /* Reserved */ 61 #define BTA_SPP_SERVICE_ID 1 /* Serial port profile. */ 62 #define BTA_DUN_SERVICE_ID 2 /* Dial-up networking profile. */ 63 #define BTA_A2DP_SOURCE_SERVICE_ID 3 /* A2DP Source profile. */ 64 #define BTA_LAP_SERVICE_ID 4 /* LAN access profile. */ 65 #define BTA_HSP_SERVICE_ID 5 /* Headset profile. */ 66 #define BTA_HFP_SERVICE_ID 6 /* Hands-free profile. */ 67 #define BTA_OPP_SERVICE_ID 7 /* Object push */ 68 #define BTA_FTP_SERVICE_ID 8 /* File transfer */ 69 #define BTA_CTP_SERVICE_ID 9 /* Cordless Terminal */ 70 #define BTA_ICP_SERVICE_ID 10 /* Intercom Terminal */ 71 #define BTA_SYNC_SERVICE_ID 11 /* Synchronization */ 72 #define BTA_BPP_SERVICE_ID 12 /* Basic printing profile */ 73 #define BTA_BIP_SERVICE_ID 13 /* Basic Imaging profile */ 74 #define BTA_PANU_SERVICE_ID 14 /* PAN User */ 75 #define BTA_NAP_SERVICE_ID 15 /* PAN Network access point */ 76 #define BTA_GN_SERVICE_ID 16 /* PAN Group Ad-hoc networks */ 77 #define BTA_SAP_SERVICE_ID 17 /* SIM Access profile */ 78 #define BTA_A2DP_SERVICE_ID 18 /* A2DP Sink */ 79 #define BTA_AVRCP_SERVICE_ID 19 /* A/V remote control */ 80 #define BTA_HID_SERVICE_ID 20 /* HID */ 81 #define BTA_VDP_SERVICE_ID 21 /* Video distribution */ 82 #define BTA_PBAP_SERVICE_ID 22 /* PhoneBook Access Server*/ 83 #define BTA_HSP_HS_SERVICE_ID 23 /* HFP HS role */ 84 #define BTA_HFP_HS_SERVICE_ID 24 /* HSP HS role */ 85 #define BTA_MAP_SERVICE_ID 25 /* Message Access Profile */ 86 #define BTA_MN_SERVICE_ID 26 /* Message Notification Service */ 87 #define BTA_HDP_SERVICE_ID 27 /* Health Device Profile */ 88 #define BTA_PCE_SERVICE_ID 28 /* PhoneBook Access Client*/ 89 90 #if BLE_INCLUDED == TRUE && BTA_GATT_INCLUDED == TRUE 91 /* BLE profile service ID */ 92 #define BTA_BLE_SERVICE_ID 29 /* GATT profile */ 93 94 // btla-specific ++ 95 #define BTA_USER_SERVICE_ID 30 /* User requested UUID */ 96 97 #define BTA_MAX_SERVICE_ID 31 98 // btla-specific -- 99 #else 100 #define BTA_USER_SERVICE_ID 29 /* User requested UUID */ 101 #define BTA_MAX_SERVICE_ID 30 102 #endif 103 /* service IDs (BTM_SEC_SERVICE_FIRST_EMPTY + 1) to (BTM_SEC_MAX_SERVICES - 1) 104 * are used by BTA JV */ 105 #define BTA_FIRST_JV_SERVICE_ID (BTM_SEC_SERVICE_FIRST_EMPTY + 1) 106 #define BTA_LAST_JV_SERVICE_ID (BTM_SEC_MAX_SERVICES - 1) 107 108 typedef UINT8 tBTA_SERVICE_ID; 109 110 /* Service ID Mask */ 111 #define BTA_RES_SERVICE_MASK 0x00000001 /* Reserved */ 112 #define BTA_SPP_SERVICE_MASK 0x00000002 /* Serial port profile. */ 113 #define BTA_DUN_SERVICE_MASK 0x00000004 /* Dial-up networking profile. */ 114 #define BTA_FAX_SERVICE_MASK 0x00000008 /* Fax profile. */ 115 #define BTA_LAP_SERVICE_MASK 0x00000010 /* LAN access profile. */ 116 #define BTA_HSP_SERVICE_MASK 0x00000020 /* HSP AG role. */ 117 #define BTA_HFP_SERVICE_MASK 0x00000040 /* HFP AG role */ 118 #define BTA_OPP_SERVICE_MASK 0x00000080 /* Object push */ 119 #define BTA_FTP_SERVICE_MASK 0x00000100 /* File transfer */ 120 #define BTA_CTP_SERVICE_MASK 0x00000200 /* Cordless Terminal */ 121 #define BTA_ICP_SERVICE_MASK 0x00000400 /* Intercom Terminal */ 122 #define BTA_SYNC_SERVICE_MASK 0x00000800 /* Synchronization */ 123 #define BTA_BPP_SERVICE_MASK 0x00001000 /* Print server */ 124 #define BTA_BIP_SERVICE_MASK 0x00002000 /* Basic Imaging */ 125 #define BTA_PANU_SERVICE_MASK 0x00004000 /* PAN User */ 126 #define BTA_NAP_SERVICE_MASK 0x00008000 /* PAN Network access point */ 127 #define BTA_GN_SERVICE_MASK 0x00010000 /* PAN Group Ad-hoc networks */ 128 #define BTA_SAP_SERVICE_MASK 0x00020000 /* PAN Group Ad-hoc networks */ 129 #define BTA_A2DP_SERVICE_MASK 0x00040000 /* Advanced audio distribution */ 130 #define BTA_AVRCP_SERVICE_MASK 0x00080000 /* A/V remote control */ 131 #define BTA_HID_SERVICE_MASK 0x00100000 /* HID */ 132 #define BTA_VDP_SERVICE_MASK 0x00200000 /* Video distribution */ 133 #define BTA_PBAP_SERVICE_MASK 0x00400000 /* Phone Book Server */ 134 #define BTA_HSP_HS_SERVICE_MASK 0x00800000 /* HFP HS role */ 135 #define BTA_HFP_HS_SERVICE_MASK 0x01000000 /* HSP HS role */ 136 #define BTA_MAS_SERVICE_MASK 0x02000000 /* Message Access Profile */ 137 #define BTA_MN_SERVICE_MASK 0x04000000 /* Message Notification Profile */ 138 #define BTA_HL_SERVICE_MASK 0x08000000 /* Health Device Profile */ 139 #define BTA_PCE_SERVICE_MASK 0x10000000 /* Phone Book Client */ 140 141 #if BLE_INCLUDED == TRUE && BTA_GATT_INCLUDED == TRUE 142 #define BTA_BLE_SERVICE_MASK 0x20000000 /* GATT based service */ 143 // btla-specific ++ 144 #define BTA_USER_SERVICE_MASK 0x40000000 /* Message Notification Profile */ 145 // btla-specific -- 146 #else 147 // btla-specific ++ 148 #define BTA_USER_SERVICE_MASK 0x20000000 /* Message Notification Profile */ 149 // btla-specific -- 150 #endif 151 152 #if BLE_INCLUDED == TRUE && BTA_GATT_INCLUDED == TRUE 153 #define BTA_ALL_SERVICE_MASK 0x3FFFFFFF /* All services supported by BTA. */ 154 #else 155 #define BTA_ALL_SERVICE_MASK 0x1FFFFFFF /* All services supported by BTA. */ 156 #endif 157 158 typedef UINT32 tBTA_SERVICE_MASK; 159 160 /* extended service mask, including mask with one or more GATT UUID */ 161 typedef struct 162 { 163 tBTA_SERVICE_MASK srvc_mask; 164 UINT8 num_uuid; 165 tBT_UUID *p_uuid; 166 }tBTA_SERVICE_MASK_EXT; 167 168 /* Security Setting Mask */ 169 #define BTA_SEC_NONE BTM_SEC_NONE /* No security. */ 170 #define BTA_SEC_AUTHORIZE (BTM_SEC_IN_AUTHORIZE ) /* Authorization required (only needed for out going connection )*/ 171 #define BTA_SEC_AUTHENTICATE (BTM_SEC_IN_AUTHENTICATE | BTM_SEC_OUT_AUTHENTICATE) /* Authentication required. */ 172 #define BTA_SEC_ENCRYPT (BTM_SEC_IN_ENCRYPT | BTM_SEC_OUT_ENCRYPT) /* Encryption required. */ 173 174 typedef UINT8 tBTA_SEC; 175 176 /* Ignore for Discoverable, Connectable, Pairable and Connectable Paired only device modes */ 177 178 #define BTA_DM_IGNORE 0xFF 179 180 #define BTA_ALL_APP_ID 0xFF 181 182 /* Discoverable Modes */ 183 #define BTA_DM_NON_DISC BTM_NON_DISCOVERABLE /* Device is not discoverable. */ 184 #define BTA_DM_GENERAL_DISC BTM_GENERAL_DISCOVERABLE /* General discoverable. */ 185 #define BTA_DM_LIMITED_DISC BTM_LIMITED_DISCOVERABLE /* Limited discoverable. */ 186 #if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 187 #define BTA_DM_BLE_NON_DISCOVERABLE BTM_BLE_NON_DISCOVERABLE /* Device is not LE discoverable */ 188 #define BTA_DM_BLE_GENERAL_DISCOVERABLE BTM_BLE_GENERAL_DISCOVERABLE /* Device is LE General discoverable */ 189 #define BTA_DM_BLE_LIMITED_DISCOVERABLE BTM_BLE_LIMITED_DISCOVERABLE /* Device is LE Limited discoverable */ 190 #endif 191 typedef UINT16 tBTA_DM_DISC; /* this discoverability mode is a bit mask among BR mode and LE mode */ 192 193 /* Connectable Modes */ 194 #define BTA_DM_NON_CONN BTM_NON_CONNECTABLE /* Device is not connectable. */ 195 #define BTA_DM_CONN BTM_CONNECTABLE /* Device is connectable. */ 196 #if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 197 #define BTA_DM_BLE_NON_CONNECTABLE BTM_BLE_NON_CONNECTABLE /* Device is LE non-connectable. */ 198 #define BTA_DM_BLE_CONNECTABLE BTM_BLE_CONNECTABLE /* Device is LE connectable. */ 199 #endif 200 201 // btla-specific ++ 202 typedef UINT16 tBTA_DM_CONN; 203 204 #define BTA_TRANSPORT_UNKNOWN 0 205 #define BTA_TRANSPORT_BR_EDR BT_TRANSPORT_BR_EDR 206 #define BTA_TRANSPORT_LE BT_TRANSPORT_LE 207 typedef tBT_TRANSPORT tBTA_TRANSPORT; 208 209 /* Pairable Modes */ 210 #define BTA_DM_PAIRABLE 1 211 #define BTA_DM_NON_PAIRABLE 0 212 213 /* Connectable Paired Only Mode */ 214 #define BTA_DM_CONN_ALL 0 215 #define BTA_DM_CONN_PAIRED 1 216 217 /* Inquiry Modes */ 218 #define BTA_DM_INQUIRY_NONE BTM_INQUIRY_NONE /*No BR inquiry. */ 219 #define BTA_DM_GENERAL_INQUIRY BTM_GENERAL_INQUIRY /* Perform general inquiry. */ 220 #define BTA_DM_LIMITED_INQUIRY BTM_LIMITED_INQUIRY /* Perform limited inquiry. */ 221 222 #if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 223 #define BTA_BLE_INQUIRY_NONE BTM_BLE_INQUIRY_NONE 224 #define BTA_BLE_GENERAL_INQUIRY BTM_BLE_GENERAL_INQUIRY /* Perform LE general inquiry. */ 225 #define BTA_BLE_LIMITED_INQUIRY BTM_BLE_LIMITED_INQUIRY /* Perform LE limited inquiry. */ 226 #endif 227 typedef UINT8 tBTA_DM_INQ_MODE; 228 229 /* Inquiry Filter Type */ 230 #define BTA_DM_INQ_CLR BTM_CLR_INQUIRY_FILTER /* Clear inquiry filter. */ 231 #define BTA_DM_INQ_DEV_CLASS BTM_FILTER_COND_DEVICE_CLASS /* Filter on device class. */ 232 #define BTA_DM_INQ_BD_ADDR BTM_FILTER_COND_BD_ADDR /* Filter on a specific BD address. */ 233 234 typedef UINT8 tBTA_DM_INQ_FILT; 235 236 /* Authorize Response */ 237 #define BTA_DM_AUTH_PERM 0 /* Authorized for future connections to the service */ 238 #define BTA_DM_AUTH_TEMP 1 /* Authorized for current connection only */ 239 #define BTA_DM_NOT_AUTH 2 /* Not authorized for the service */ 240 241 typedef UINT8 tBTA_AUTH_RESP; 242 243 /* M/S preferred roles */ 244 #define BTA_ANY_ROLE 0x00 245 #define BTA_MASTER_ROLE_PREF 0x01 246 #define BTA_MASTER_ROLE_ONLY 0x02 247 248 typedef UINT8 tBTA_PREF_ROLES; 249 250 enum 251 { 252 253 BTA_DM_NO_SCATTERNET, /* Device doesn't support scatternet, it might 254 support "role switch during connection" for 255 an incoming connection, when it already has 256 another connection in master role */ 257 BTA_DM_PARTIAL_SCATTERNET, /* Device supports partial scatternet. It can have 258 simulateous connection in Master and Slave roles 259 for short period of time */ 260 BTA_DM_FULL_SCATTERNET /* Device can have simultaneous connection in master 261 and slave roles */ 262 263 }; 264 265 266 /* Inquiry filter device class condition */ 267 typedef struct 268 { 269 DEV_CLASS dev_class; /* device class of interest */ 270 DEV_CLASS dev_class_mask; /* mask to determine the bits of device class of interest */ 271 } tBTA_DM_COD_COND; 272 273 274 /* Inquiry Filter Condition */ 275 typedef union 276 { 277 BD_ADDR bd_addr; /* BD address of device to filter. */ 278 tBTA_DM_COD_COND dev_class_cond; /* Device class filter condition */ 279 } tBTA_DM_INQ_COND; 280 281 /* Inquiry Parameters */ 282 typedef struct 283 { 284 tBTA_DM_INQ_MODE mode; /* Inquiry mode, limited or general. */ 285 UINT8 duration; /* Inquiry duration in 1.28 sec units. */ 286 UINT8 max_resps; /* Maximum inquiry responses. Set to zero for unlimited responses. */ 287 BOOLEAN report_dup; /* report duplicated inquiry response with higher RSSI value */ 288 tBTA_DM_INQ_FILT filter_type; /* Filter condition type. */ 289 tBTA_DM_INQ_COND filter_cond; /* Filter condition data. */ 290 #if (defined(BTA_HOST_INTERLEAVE_SEARCH) && BTA_HOST_INTERLEAVE_SEARCH == TRUE) 291 UINT8 intl_duration[4];/*duration array storing the interleave scan's time portions*/ 292 #endif 293 } tBTA_DM_INQ; 294 295 typedef struct 296 { 297 UINT8 bta_dm_eir_min_name_len; /* minimum length of local name when it is shortened */ 298 #if (BTA_EIR_CANNED_UUID_LIST == TRUE) 299 UINT8 bta_dm_eir_uuid16_len; /* length of 16-bit UUIDs */ 300 UINT8 *bta_dm_eir_uuid16; /* 16-bit UUIDs */ 301 #else 302 UINT32 uuid_mask[BTM_EIR_SERVICE_ARRAY_SIZE]; /* mask of UUID list in EIR */ 303 #endif 304 INT8 *bta_dm_eir_inq_tx_power; /* Inquiry TX power */ 305 UINT8 bta_dm_eir_flag_len; /* length of flags in bytes */ 306 UINT8 *bta_dm_eir_flags; /* flags for EIR */ 307 UINT8 bta_dm_eir_manufac_spec_len; /* length of manufacturer specific in bytes */ 308 UINT8 *bta_dm_eir_manufac_spec; /* manufacturer specific */ 309 UINT8 bta_dm_eir_additional_len; /* length of additional data in bytes */ 310 UINT8 *bta_dm_eir_additional; /* additional data */ 311 } tBTA_DM_EIR_CONF; 312 313 #if BLE_INCLUDED == TRUE 314 /* ADV data flag bit definition used for BTM_BLE_AD_TYPE_FLAG */ 315 #define BTA_BLE_LIMIT_DISC_FLAG BTM_BLE_LIMIT_DISC_FLAG 316 #define BTA_BLE_GEN_DISC_FLAG BTM_BLE_GEN_DISC_FLAG 317 #define BTA_BLE_BREDR_NOT_SPT BTM_BLE_BREDR_NOT_SPT 318 #define BTA_BLE_DMT_CONTROLLER_SPT BTM_BLE_DMT_CONTROLLER_SPT 319 #define BTA_BLE_DMT_HOST_SPT BTM_BLE_DMT_HOST_SPT 320 #define BTA_BLE_NON_LIMIT_DISC_FLAG BTM_BLE_NON_LIMIT_DISC_FLAG 321 #define BTA_BLE_ADV_FLAG_MASK BTM_BLE_ADV_FLAG_MASK 322 #define BTA_BLE_LIMIT_DISC_MASK BTM_BLE_LIMIT_DISC_MASK 323 324 /* ADV data bit mask */ 325 #define BTA_BLE_AD_BIT_DEV_NAME BTM_BLE_AD_BIT_DEV_NAME 326 #define BTA_BLE_AD_BIT_FLAGS BTM_BLE_AD_BIT_FLAGS 327 #define BTA_BLE_AD_BIT_MANU BTM_BLE_AD_BIT_MANU 328 #define BTA_BLE_AD_BIT_TX_PWR BTM_BLE_AD_BIT_TX_PWR 329 #define BTA_BLE_AD_BIT_INT_RANGE BTM_BLE_AD_BIT_INT_RANGE 330 #define BTA_BLE_AD_BIT_SERVICE BTM_BLE_AD_BIT_SERVICE 331 #define BTA_BLE_AD_BIT_APPEARANCE BTM_BLE_AD_BIT_APPEARANCE 332 #define BTA_BLE_AD_BIT_PROPRIETARY BTM_BLE_AD_BIT_PROPRIETARY 333 #define BTA_DM_BLE_AD_BIT_SERVICE_SOL BTM_BLE_AD_BIT_SERVICE_SOL 334 #define BTA_DM_BLE_AD_BIT_SERVICE_DATA BTM_BLE_AD_BIT_SERVICE_DATA 335 #define BTA_DM_BLE_AD_BIT_SIGN_DATA BTM_BLE_AD_BIT_SIGN_DATA 336 #define BTA_DM_BLE_AD_BIT_SERVICE_128SOL BTM_BLE_AD_BIT_SERVICE_128SOL 337 #define BTA_DM_BLE_AD_BIT_PUBLIC_ADDR BTM_BLE_AD_BIT_PUBLIC_ADDR 338 #define BTA_DM_BLE_AD_BIT_RANDOM_ADDR BTM_BLE_AD_BIT_RANDOM_ADDR 339 #define BTA_DM_BLE_AD_BIT_SERVICE_128 BTM_BLE_AD_BIT_SERVICE_128 /*128-bit Service UUIDs*/ 340 341 typedef tBTM_BLE_AD_MASK tBTA_BLE_AD_MASK; 342 343 /* slave preferred connection interval range */ 344 typedef struct 345 { 346 UINT16 low; 347 UINT16 hi; 348 349 }tBTA_BLE_INT_RANGE; 350 351 /* Service tag supported in the device */ 352 typedef struct 353 { 354 UINT8 num_service; 355 BOOLEAN list_cmpl; 356 UINT16 *p_uuid; 357 }tBTA_BLE_SERVICE; 358 359 360 typedef struct 361 { 362 UINT8 len; 363 UINT8 *p_val; 364 }tBTA_BLE_MANU; 365 366 typedef struct 367 { 368 UINT8 adv_type; 369 UINT8 len; 370 UINT8 *p_val; /* number of len byte */ 371 }tBTA_BLE_PROP_ELEM; 372 373 /* vendor proprietary adv type */ 374 typedef struct 375 { 376 UINT8 num_elem; 377 tBTA_BLE_PROP_ELEM *p_elem; 378 }tBTA_BLE_PROPRIETARY; 379 380 typedef struct 381 { 382 tBT_UUID service_uuid; 383 UINT8 len; 384 UINT8 *p_val; 385 }tBTA_BLE_SERVICE_DATA; 386 387 typedef tBTM_BLE_128SERVICE tBTA_BLE_128SERVICE; 388 typedef tBTM_BLE_32SERVICE tBTA_BLE_32SERVICE; 389 390 typedef struct 391 { 392 tBTA_BLE_INT_RANGE int_range; /* slave prefered conn interval range */ 393 tBTA_BLE_MANU *p_manu; /* manufacturer data */ 394 tBTA_BLE_SERVICE *p_services; /* 16 bits services */ 395 tBTA_BLE_128SERVICE *p_services_128b; /* 128 bits service */ 396 tBTA_BLE_32SERVICE *p_service_32b; /* 32 bits Service UUID */ 397 tBTA_BLE_SERVICE *p_sol_services; /* 16 bits services Solicitation UUIDs */ 398 tBTA_BLE_32SERVICE *p_sol_service_32b; /* List of 32 bit Service Solicitation UUIDs */ 399 tBTA_BLE_128SERVICE *p_sol_service_128b;/* List of 128 bit Service Solicitation UUIDs */ 400 tBTA_BLE_PROPRIETARY *p_proprietary; /* proprietary data */ 401 tBTA_BLE_SERVICE_DATA *p_service_data; /* service data */ 402 UINT16 appearance; /* appearance data */ 403 UINT8 flag; 404 UINT8 tx_power; 405 }tBTA_BLE_ADV_DATA; 406 407 typedef void (tBTA_SET_ADV_DATA_CMPL_CBACK) (tBTA_STATUS status); 408 409 /* advertising channel map */ 410 #define BTA_BLE_ADV_CHNL_37 BTM_BLE_ADV_CHNL_37 411 #define BTA_BLE_ADV_CHNL_38 BTM_BLE_ADV_CHNL_38 412 #define BTA_BLE_ADV_CHNL_39 BTM_BLE_ADV_CHNL_39 413 typedef tBTM_BLE_ADV_CHNL_MAP tBTA_BLE_ADV_CHNL_MAP; /* use as a bit mask */ 414 415 /* advertising filter policy */ 416 typedef tBTM_BLE_AFP tBTA_BLE_AFP; 417 418 /* adv event type */ 419 #define BTA_BLE_CONNECT_EVT BTM_BLE_CONNECT_EVT /* Connectable undirected advertising */ 420 #define BTA_BLE_CONNECT_DIR_EVT BTM_BLE_CONNECT_DIR_EVT /* Connectable directed advertising */ 421 #define BTA_BLE_DISCOVER_EVT BTM_BLE_DISCOVER_EVT /* Scannable undirected advertising */ 422 #define BTA_BLE_NON_CONNECT_EVT BTM_BLE_NON_CONNECT_EVT /* Non connectable undirected advertising */ 423 typedef UINT8 tBTA_BLE_ADV_EVT; 424 425 /* adv tx power level */ 426 #define BTA_BLE_ADV_TX_POWER_MIN 0 /* minimum tx power */ 427 #define BTA_BLE_ADV_TX_POWER_LOW 1 /* low tx power */ 428 #define BTA_BLE_ADV_TX_POWER_MID 2 /* middle tx power */ 429 #define BTA_BLE_ADV_TX_POWER_UPPER 3 /* upper tx power */ 430 #define BTA_BLE_ADV_TX_POWER_MAX 4 /* maximum tx power */ 431 typedef UINT8 tBTA_BLE_ADV_TX_POWER; 432 433 /* advertising instance parameters */ 434 typedef struct 435 { 436 UINT16 adv_int_min; /* minimum adv interval */ 437 UINT16 adv_int_max; /* maximum adv interval */ 438 tBTA_BLE_ADV_EVT adv_type; /* adv event type */ 439 tBTA_BLE_ADV_CHNL_MAP channel_map; /* adv channel map */ 440 tBTA_BLE_AFP adv_filter_policy; /* advertising filter policy */ 441 tBTA_BLE_ADV_TX_POWER tx_power; /* adv tx power */ 442 }tBTA_BLE_ADV_PARAMS; 443 444 /* These are the fields returned in each device adv packet. It 445 ** is returned in the results callback if registered. 446 */ 447 typedef struct 448 { 449 UINT8 conn_mode; 450 tBTA_BLE_AD_MASK ad_mask; /* mask of the valid adv data field */ 451 UINT8 flag; 452 UINT8 tx_power_level; 453 UINT8 remote_name_len; 454 UINT8 *p_remote_name; 455 tBTA_BLE_SERVICE service; 456 } tBTA_BLE_INQ_DATA; 457 458 enum 459 { 460 BTA_BLE_SCAN_MODE_PASS=1, 461 BTA_BLE_SCAN_MODE_ACTI=2, 462 BTA_BLE_SCAN_MODE_PASS_ACTI=3 463 }; 464 typedef UINT8 tBTA_BLE_SCAN_MODE; 465 466 enum 467 { 468 BTA_BLE_DISCARD_OLD_ITEMS=0, 469 BTA_BLE_DISCARD_LOWER_RSSI_ITEMS=1 470 }; 471 typedef UINT8 tBTA_BLE_DISCARD_RULE; 472 473 enum 474 { 475 BTA_BLE_ADV_SEEN_FIRST_TIME=0, 476 BTA_BLE_ADV_TRACKING_TIMEOUT=1 477 }; 478 typedef UINT8 tBTA_BLE_ADV_CHANGE_REASON; 479 480 enum 481 { 482 BTA_BLE_BATCH_SCAN_ENB_EVT = 1, 483 BTA_BLE_BATCH_SCAN_CFG_STRG_EVT = 2, 484 BTA_BLE_BATCH_SCAN_DATA_EVT = 3, 485 BTA_BLE_BATCH_SCAN_THRES_EVT = 4, 486 BTA_BLE_BATCH_SCAN_PARAM_EVT = 5, 487 BTA_BLE_BATCH_SCAN_DIS_EVT = 6 488 }; 489 typedef tBTM_BLE_BATCH_SCAN_EVT tBTA_BLE_BATCH_SCAN_EVT; 490 491 typedef tBTM_BLE_TRACK_ADV_ACTION tBTA_BLE_TRACK_ADV_ACTION; 492 #endif 493 494 /* BLE customer specific feature function type definitions */ 495 /* data type used on customer specific feature for RSSI monitoring */ 496 #define BTA_BLE_RSSI_ALERT_HI 0 497 #define BTA_BLE_RSSI_ALERT_RANGE 1 498 #define BTA_BLE_RSSI_ALERT_LO 2 499 typedef UINT8 tBTA_DM_BLE_RSSI_ALERT_TYPE; 500 501 #define BTA_BLE_RSSI_ALERT_NONE BTM_BLE_RSSI_ALERT_NONE /* (0) */ 502 #define BTA_BLE_RSSI_ALERT_HI_BIT BTM_BLE_RSSI_ALERT_HI_BIT /* (1) */ 503 #define BTA_BLE_RSSI_ALERT_RANGE_BIT BTM_BLE_RSSI_ALERT_RANGE_BIT /* (1 << 1) */ 504 #define BTA_BLE_RSSI_ALERT_LO_BIT BTM_BLE_RSSI_ALERT_LO_BIT /* (1 << 2) */ 505 typedef UINT8 tBTA_DM_BLE_RSSI_ALERT_MASK; 506 507 508 typedef void (tBTA_DM_BLE_RSSI_CBACK) (BD_ADDR bd_addr, tBTA_DM_BLE_RSSI_ALERT_TYPE alert_type, INT8 rssi); 509 510 /* max number of filter spot for different filter type */ 511 #define BTA_DM_BLE_MAX_UUID_FILTER BTM_BLE_MAX_UUID_FILTER /* 8 */ 512 #define BTA_DM_BLE_MAX_ADDR_FILTER BTM_BLE_MAX_ADDR_FILTER /* 8 */ 513 #define BTA_DM_BLE_PF_STR_COND_MAX BTM_BLE_PF_STR_COND_MAX /* 4 apply to manu data , or local name */ 514 #define BTA_DM_BLE_PF_STR_LEN_MAX BTM_BLE_PF_STR_LEN_MAX /* match for first 20 bytes */ 515 516 #define BTA_DM_BLE_PF_LOGIC_OR 0 517 #define BTA_DM_BLE_PF_LOGIC_AND 1 518 typedef UINT8 tBTA_DM_BLE_PF_LOGIC_TYPE; 519 520 enum 521 { 522 BTA_DM_BLE_SCAN_COND_ADD, 523 BTA_DM_BLE_SCAN_COND_DELETE, 524 BTA_DM_BLE_SCAN_COND_CLEAR = 2 525 }; 526 typedef UINT8 tBTA_DM_BLE_SCAN_COND_OP; 527 528 /* ADV payload filtering vendor specific call event */ 529 enum 530 { 531 BTA_BLE_SCAN_PF_ENABLE_EVT = 7, 532 BTA_BLE_SCAN_PF_COND_EVT 533 }; 534 535 /* filter selection bit index */ 536 #define BTA_DM_BLE_PF_ADDR_FILTER BTM_BLE_PF_ADDR_FILTER 537 #define BTA_DM_BLE_PF_SRVC_DATA BTM_BLE_PF_SRVC_DATA 538 #define BTA_DM_BLE_PF_SRVC_UUID BTM_BLE_PF_SRVC_UUID 539 #define BTA_DM_BLE_PF_SRVC_SOL_UUID BTM_BLE_PF_SRVC_SOL_UUID 540 #define BTA_DM_BLE_PF_LOCAL_NAME BTM_BLE_PF_LOCAL_NAME 541 #define BTA_DM_BLE_PF_MANU_DATA BTM_BLE_PF_MANU_DATA 542 #define BTA_DM_BLE_PF_SRVC_DATA_PATTERN BTM_BLE_PF_SRVC_DATA_PATTERN 543 #define BTA_DM_BLE_PF_TYPE_ALL BTM_BLE_PF_TYPE_ALL 544 #define BTA_DM_BLE_PF_TYPE_MAX BTM_BLE_PF_TYPE_MAX 545 typedef UINT8 tBTA_DM_BLE_PF_COND_TYPE; 546 547 typedef union 548 { 549 UINT16 uuid16_mask; 550 UINT32 uuid32_mask; 551 UINT8 uuid128_mask[LEN_UUID_128]; 552 }tBTA_DM_BLE_PF_COND_MASK; 553 554 typedef struct 555 { 556 tBLE_BD_ADDR *p_target_addr; /* target address, if NULL, generic UUID filter */ 557 tBT_UUID uuid; /* UUID condition */ 558 tBTA_DM_BLE_PF_LOGIC_TYPE cond_logic; /* AND/OR */ 559 tBTA_DM_BLE_PF_COND_MASK *p_uuid_mask; /* UUID condition mask, if NULL, match exact as UUID condition */ 560 }tBTA_DM_BLE_PF_UUID_COND; 561 562 typedef struct 563 { 564 UINT8 data_len; /* <= 20 bytes */ 565 UINT8 *p_data; 566 }tBTA_DM_BLE_PF_LOCAL_NAME_COND; 567 568 typedef struct 569 { 570 UINT16 company_id; /* company ID */ 571 UINT8 data_len; /* <= 20 bytes */ 572 UINT8 *p_pattern; 573 UINT16 company_id_mask; /* UUID value mask */ 574 UINT8 *p_pattern_mask; /* Manufacturer data matching mask, same length 575 as data pattern, set to all 0xff, match exact data */ 576 }tBTA_DM_BLE_PF_MANU_COND; 577 578 typedef struct 579 { 580 UINT16 uuid; /* service ID */ 581 UINT8 data_len; /* <= 20 bytes */ 582 UINT8 *p_pattern; 583 UINT8 *p_pattern_mask; /* Service data matching mask, same length 584 as data pattern, set to all 0xff, match exact data */ 585 }tBTA_DM_BLE_PF_SRVC_PATTERN_COND; 586 587 typedef union 588 { 589 tBLE_BD_ADDR target_addr; 590 tBTA_DM_BLE_PF_LOCAL_NAME_COND local_name; /* lcoal name filtering */ 591 tBTA_DM_BLE_PF_MANU_COND manu_data; /* manufactuer data filtering */ 592 tBTA_DM_BLE_PF_UUID_COND srvc_uuid; /* service UUID filtering */ 593 tBTA_DM_BLE_PF_UUID_COND solicitate_uuid; /* solicitated service UUID filtering */ 594 tBTA_DM_BLE_PF_SRVC_PATTERN_COND srvc_data; /* service data pattern */ 595 }tBTA_DM_BLE_PF_COND_PARAM; 596 597 typedef UINT8 tBTA_DM_BLE_PF_FILT_INDEX; 598 typedef UINT8 tBTA_DM_BLE_PF_AVBL_SPACE; 599 600 typedef INT8 tBTA_DM_RSSI_VALUE; 601 typedef UINT8 tBTA_DM_LINK_QUALITY_VALUE; 602 603 604 /* signal strength mask */ 605 #define BTA_SIG_STRENGTH_RSSI_MASK 1 606 #define BTA_SIG_STRENGTH_LINK_QUALITY_MASK 2 607 608 typedef UINT8 tBTA_SIG_STRENGTH_MASK; 609 610 611 /* Security Callback Events */ 612 #define BTA_DM_ENABLE_EVT 0 /* Enable Event */ 613 #define BTA_DM_DISABLE_EVT 1 /* Disable Event */ 614 #define BTA_DM_PIN_REQ_EVT 2 /* PIN request. */ 615 #define BTA_DM_AUTH_CMPL_EVT 3 /* Authentication complete indication. */ 616 #define BTA_DM_AUTHORIZE_EVT 4 /* Authorization request. */ 617 #define BTA_DM_LINK_UP_EVT 5 /* Connection UP event */ 618 #define BTA_DM_LINK_DOWN_EVT 6 /* Connection DOWN event */ 619 #define BTA_DM_SIG_STRENGTH_EVT 7 /* Signal strength for bluetooth connection */ 620 #define BTA_DM_BUSY_LEVEL_EVT 8 /* System busy level */ 621 #define BTA_DM_BOND_CANCEL_CMPL_EVT 9 /* Bond cancel complete indication */ 622 #define BTA_DM_SP_CFM_REQ_EVT 10 /* Simple Pairing User Confirmation request. */ 623 #define BTA_DM_SP_KEY_NOTIF_EVT 11 /* Simple Pairing Passkey Notification */ 624 #define BTA_DM_SP_RMT_OOB_EVT 12 /* Simple Pairing Remote OOB Data request. */ 625 #define BTA_DM_SP_KEYPRESS_EVT 13 /* Key press notification event. */ 626 #define BTA_DM_ROLE_CHG_EVT 14 /* Role Change event. */ 627 #define BTA_DM_BLE_KEY_EVT 15 /* BLE SMP key event for peer device keys */ 628 #define BTA_DM_BLE_SEC_REQ_EVT 16 /* BLE SMP security request */ 629 #define BTA_DM_BLE_PASSKEY_NOTIF_EVT 17 /* SMP passkey notification event */ 630 #define BTA_DM_BLE_PASSKEY_REQ_EVT 18 /* SMP passkey request event */ 631 #define BTA_DM_BLE_OOB_REQ_EVT 19 /* SMP OOB request event */ 632 #define BTA_DM_BLE_LOCAL_IR_EVT 20 /* BLE local IR event */ 633 #define BTA_DM_BLE_LOCAL_ER_EVT 21 /* BLE local ER event */ 634 // btla-specific ++ 635 #define BTA_DM_BLE_AUTH_CMPL_EVT 22 /* BLE Auth complete */ 636 // btla-specific -- 637 #define BTA_DM_DEV_UNPAIRED_EVT 23 638 #define BTA_DM_HW_ERROR_EVT 24 /* BT Chip H/W error */ 639 #define BTA_DM_LE_FEATURES_READ 25 /* Cotroller specific LE features are read */ 640 #define BTA_DM_ENER_INFO_READ 26 /* Energy info read */ 641 typedef UINT8 tBTA_DM_SEC_EVT; 642 643 /* Structure associated with BTA_DM_ENABLE_EVT */ 644 typedef struct 645 { 646 BD_ADDR bd_addr; /* BD address of local device. */ 647 tBTA_STATUS status; 648 } tBTA_DM_ENABLE; 649 650 /* Structure associated with BTA_DM_PIN_REQ_EVT */ 651 typedef struct 652 { 653 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 654 BD_ADDR bd_addr; /* BD address peer device. */ 655 DEV_CLASS dev_class; /* Class of Device */ 656 BD_NAME bd_name; /* Name of peer device. */ 657 } tBTA_DM_PIN_REQ; 658 659 /* BLE related definition */ 660 661 #define BTA_DM_AUTH_FAIL_BASE (HCI_ERR_MAX_ERR + 10) 662 #define BTA_DM_AUTH_CONVERT_SMP_CODE(x) (BTA_DM_AUTH_FAIL_BASE + (x)) 663 #define BTA_DM_AUTH_SMP_PASSKEY_FAIL BTA_DM_AUTH_CONVERT_SMP_CODE (SMP_PASSKEY_ENTRY_FAIL) 664 #define BTA_DM_AUTH_SMP_OOB_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_OOB_FAIL) 665 #define BTA_DM_AUTH_SMP_PAIR_AUTH_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_AUTH_FAIL) 666 #define BTA_DM_AUTH_SMP_CONFIRM_VALUE_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_CONFIRM_VALUE_ERR) 667 #define BTA_DM_AUTH_SMP_PAIR_NOT_SUPPORT (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_NOT_SUPPORT) 668 #define BTA_DM_AUTH_SMP_ENC_KEY_SIZE (BTA_DM_AUTH_FAIL_BASE + SMP_ENC_KEY_SIZE) 669 #define BTA_DM_AUTH_SMP_INVALID_CMD (BTA_DM_AUTH_FAIL_BASE + SMP_INVALID_CMD) 670 #define BTA_DM_AUTH_SMP_UNKNOWN_ERR (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_FAIL_UNKNOWN) 671 #define BTA_DM_AUTH_SMP_REPEATED_ATTEMPT (BTA_DM_AUTH_FAIL_BASE + SMP_REPEATED_ATTEMPTS) 672 #define BTA_DM_AUTH_SMP_INTERNAL_ERR (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_INTERNAL_ERR) 673 #define BTA_DM_AUTH_SMP_UNKNOWN_IO (BTA_DM_AUTH_FAIL_BASE + SMP_UNKNOWN_IO_CAP) 674 #define BTA_DM_AUTH_SMP_INIT_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_INIT_FAIL) 675 #define BTA_DM_AUTH_SMP_CONFIRM_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_CONFIRM_FAIL) 676 #define BTA_DM_AUTH_SMP_BUSY (BTA_DM_AUTH_FAIL_BASE + SMP_BUSY) 677 #define BTA_DM_AUTH_SMP_ENC_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_ENC_FAIL) 678 #define BTA_DM_AUTH_SMP_RSP_TIMEOUT (BTA_DM_AUTH_FAIL_BASE + SMP_RSP_TIMEOUT) 679 680 /* connection parameter boundary value and dummy value */ 681 #define BTA_DM_BLE_SCAN_INT_MIN BTM_BLE_SCAN_INT_MIN 682 #define BTA_DM_BLE_SCAN_INT_MAX BTM_BLE_SCAN_INT_MAX 683 #define BTA_DM_BLE_SCAN_WIN_MIN BTM_BLE_SCAN_WIN_MIN 684 #define BTA_DM_BLE_SCAN_WIN_MAX BTM_BLE_SCAN_WIN_MAX 685 #define BTA_DM_BLE_CONN_INT_MIN BTM_BLE_CONN_INT_MIN 686 #define BTA_DM_BLE_CONN_INT_MAX BTM_BLE_CONN_INT_MAX 687 #define BTA_DM_BLE_CONN_LATENCY_MAX BTM_BLE_CONN_LATENCY_MAX 688 #define BTA_DM_BLE_CONN_SUP_TOUT_MIN BTM_BLE_CONN_SUP_TOUT_MIN 689 #define BTA_DM_BLE_CONN_SUP_TOUT_MAX BTM_BLE_CONN_SUP_TOUT_MAX 690 #define BTA_DM_BLE_CONN_PARAM_UNDEF BTM_BLE_CONN_PARAM_UNDEF /* use this value when a specific value not to be overwritten */ 691 692 693 #define BTA_LE_KEY_PENC BTM_LE_KEY_PENC /* encryption information of peer device */ 694 #define BTA_LE_KEY_PID BTM_LE_KEY_PID /* identity key of the peer device */ 695 #define BTA_LE_KEY_PCSRK BTM_LE_KEY_PCSRK /* peer SRK */ 696 #define BTA_LE_KEY_LENC BTM_LE_KEY_LENC /* master role security information:div */ 697 #define BTA_LE_KEY_LID BTM_LE_KEY_LID /* master device ID key */ 698 #define BTA_LE_KEY_LCSRK BTM_LE_KEY_LCSRK /* local CSRK has been deliver to peer */ 699 typedef UINT8 tBTA_LE_KEY_TYPE; /* can be used as a bit mask */ 700 701 702 typedef tBTM_LE_PENC_KEYS tBTA_LE_PENC_KEYS ; 703 typedef tBTM_LE_PCSRK_KEYS tBTA_LE_PCSRK_KEYS; 704 typedef tBTM_LE_LENC_KEYS tBTA_LE_LENC_KEYS ; 705 typedef tBTM_LE_LCSRK_KEYS tBTA_LE_LCSRK_KEYS ; 706 typedef tBTM_LE_PID_KEYS tBTA_LE_PID_KEYS ; 707 708 typedef union 709 { 710 tBTA_LE_PENC_KEYS penc_key; /* received peer encryption key */ 711 tBTA_LE_PCSRK_KEYS psrk_key; /* received peer device SRK */ 712 tBTA_LE_PID_KEYS pid_key; /* peer device ID key */ 713 tBTA_LE_LENC_KEYS lenc_key; /* local encryption reproduction keys LTK = = d1(ER,DIV,0)*/ 714 tBTA_LE_LCSRK_KEYS lcsrk_key; /* local device CSRK = d1(ER,DIV,1)*/ 715 }tBTA_LE_KEY_VALUE; 716 717 #define BTA_BLE_LOCAL_KEY_TYPE_ID 1 718 #define BTA_BLE_LOCAL_KEY_TYPE_ER 2 719 typedef UINT8 tBTA_DM_BLE_LOCAL_KEY_MASK; 720 721 typedef struct 722 { 723 BT_OCTET16 ir; 724 BT_OCTET16 irk; 725 BT_OCTET16 dhk; 726 }tBTA_BLE_LOCAL_ID_KEYS; 727 728 #define BTA_DM_SEC_GRANTED BTA_SUCCESS 729 #define BTA_DM_SEC_PAIR_NOT_SPT BTA_DM_AUTH_SMP_PAIR_NOT_SUPPORT 730 #define BTA_DM_SEC_REP_ATTEMPTS BTA_DM_AUTH_SMP_REPEATED_ATTEMPT 731 typedef UINT8 tBTA_DM_BLE_SEC_GRANT; 732 733 734 #define BTA_DM_BLE_ONN_NONE BTM_BLE_CONN_NONE 735 #define BTA_DM_BLE_CONN_AUTO BTM_BLE_CONN_AUTO 736 #define BTA_DM_BLE_CONN_SELECTIVE BTM_BLE_CONN_SELECTIVE 737 typedef UINT8 tBTA_DM_BLE_CONN_TYPE; 738 739 typedef BOOLEAN (tBTA_DM_BLE_SEL_CBACK)(BD_ADDR random_bda, UINT8 *p_remote_name); 740 741 /* Structure associated with BTA_DM_BLE_SEC_REQ_EVT */ 742 typedef struct 743 { 744 BD_ADDR bd_addr; /* peer address */ 745 BD_NAME bd_name; /* peer device name */ 746 } tBTA_DM_BLE_SEC_REQ; 747 748 typedef struct 749 { 750 BD_ADDR bd_addr; /* peer address */ 751 tBTM_LE_KEY_TYPE key_type; 752 tBTM_LE_KEY_VALUE key_value; 753 }tBTA_DM_BLE_KEY; 754 755 /* Structure associated with BTA_DM_AUTH_CMPL_EVT */ 756 typedef struct 757 { 758 BD_ADDR bd_addr; /* BD address peer device. */ 759 BD_NAME bd_name; /* Name of peer device. */ 760 BOOLEAN key_present; /* Valid link key value in key element */ 761 LINK_KEY key; /* Link key associated with peer device. */ 762 UINT8 key_type; /* The type of Link Key */ 763 BOOLEAN success; /* TRUE of authentication succeeded, FALSE if failed. */ 764 #if BLE_INCLUDED == TRUE 765 BOOLEAN privacy_enabled; /* used for BLE device only */ 766 #endif 767 UINT8 fail_reason; /* The HCI reason/error code for when success=FALSE */ 768 769 } tBTA_DM_AUTH_CMPL; 770 771 772 /* Structure associated with BTA_DM_AUTHORIZE_EVT */ 773 typedef struct 774 { 775 BD_ADDR bd_addr; /* BD address peer device. */ 776 BD_NAME bd_name; /* Name of peer device. */ 777 tBTA_SERVICE_ID service; /* Service ID to authorize. */ 778 // btla-specific ++ 779 DEV_CLASS dev_class; 780 // btla-specific -- 781 } tBTA_DM_AUTHORIZE; 782 783 /* Structure associated with BTA_DM_LINK_UP_EVT */ 784 typedef struct 785 { 786 BD_ADDR bd_addr; /* BD address peer device. */ 787 #if BLE_INCLUDED == TRUE 788 tBTA_TRANSPORT link_type; 789 #endif 790 } tBTA_DM_LINK_UP; 791 792 /* Structure associated with BTA_DM_LINK_DOWN_EVT */ 793 typedef struct 794 { 795 BD_ADDR bd_addr; /* BD address peer device. */ 796 UINT8 status; /* connection open/closed */ 797 BOOLEAN is_removed; /* TRUE if device is removed when link is down */ 798 #if BLE_INCLUDED == TRUE 799 tBTA_TRANSPORT link_type; 800 #endif 801 } tBTA_DM_LINK_DOWN; 802 803 /* Structure associated with BTA_DM_ROLE_CHG_EVT */ 804 typedef struct 805 { 806 BD_ADDR bd_addr; /* BD address peer device. */ 807 UINT8 new_role; /* the new connection role */ 808 } tBTA_DM_ROLE_CHG; 809 810 /* Structure associated with BTA_DM_SIG_STRENGTH_EVT */ 811 typedef struct 812 { 813 BD_ADDR bd_addr; /* BD address peer device. */ 814 tBTA_SIG_STRENGTH_MASK mask; /* mask for the values that are valid */ 815 tBTA_DM_RSSI_VALUE rssi_value; 816 tBTA_DM_LINK_QUALITY_VALUE link_quality_value; 817 818 } tBTA_DM_SIG_STRENGTH; 819 820 /* Structure associated with BTA_DM_BUSY_LEVEL_EVT */ 821 typedef struct 822 { 823 UINT8 level; /* when paging or inquiring, level is 10. 824 Otherwise, the number of ACL links */ 825 UINT8 level_flags; /* indicates individual flags */ 826 } tBTA_DM_BUSY_LEVEL; 827 828 #define BTA_IO_CAP_OUT BTM_IO_CAP_OUT /* DisplayOnly */ 829 #define BTA_IO_CAP_IO BTM_IO_CAP_IO /* DisplayYesNo */ 830 #define BTA_IO_CAP_IN BTM_IO_CAP_IN /* KeyboardOnly */ 831 #define BTA_IO_CAP_NONE BTM_IO_CAP_NONE /* NoInputNoOutput */ 832 typedef tBTM_IO_CAP tBTA_IO_CAP; 833 834 #define BTA_AUTH_SP_NO BTM_AUTH_SP_NO /* 0 MITM Protection Not Required - Single Profile/non-bonding 835 Numeric comparison with automatic accept allowed */ 836 #define BTA_AUTH_SP_YES BTM_AUTH_SP_YES /* 1 MITM Protection Required - Single Profile/non-bonding 837 Use IO Capabilities to determine authentication procedure */ 838 #define BTA_AUTH_AP_NO BTM_AUTH_AP_NO /* 2 MITM Protection Not Required - All Profiles/dedicated bonding 839 Numeric comparison with automatic accept allowed */ 840 #define BTA_AUTH_AP_YES BTM_AUTH_AP_YES /* 3 MITM Protection Required - All Profiles/dedicated bonding 841 Use IO Capabilities to determine authentication procedure */ 842 #define BTA_AUTH_SPGB_NO BTM_AUTH_SPGB_NO /* 4 MITM Protection Not Required - Single Profiles/general bonding 843 Numeric comparison with automatic accept allowed */ 844 #define BTA_AUTH_SPGB_YES BTM_AUTH_SPGB_YES /* 5 MITM Protection Required - Single Profiles/general bonding 845 Use IO Capabilities to determine authentication procedure */ 846 typedef tBTM_AUTH_REQ tBTA_AUTH_REQ; 847 848 #define BTA_AUTH_DD_BOND BTM_AUTH_DD_BOND /* 2 this bit is set for dedicated bonding */ 849 #define BTA_AUTH_GEN_BOND BTM_AUTH_SPGB_NO /* 4 this bit is set for general bonding */ 850 #define BTA_AUTH_BONDS BTM_AUTH_BONDS /* 6 the general/dedicated bonding bits */ 851 852 #define BTA_LE_AUTH_NO_BOND BTM_LE_AUTH_REQ_NO_BOND /* 0*/ 853 #define BTA_LE_AUTH_BOND BTM_LE_AUTH_REQ_BOND /* 1 << 0 */ 854 #define BTA_LE_AUTH_REQ_MITM BTM_LE_AUTH_REQ_MITM /* 1 << 2 */ 855 typedef tBTM_LE_AUTH_REQ tBTA_LE_AUTH_REQ; /* combination of the above bit pattern */ 856 857 #define BTA_OOB_NONE BTM_OOB_NONE 858 #define BTA_OOB_PRESENT BTM_OOB_PRESENT 859 #if BTM_OOB_INCLUDED == TRUE 860 #define BTA_OOB_UNKNOWN BTM_OOB_UNKNOWN 861 #endif 862 typedef tBTM_OOB_DATA tBTA_OOB_DATA; 863 864 /* Structure associated with BTA_DM_SP_CFM_REQ_EVT */ 865 typedef struct 866 { 867 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 868 BD_ADDR bd_addr; /* peer address */ 869 DEV_CLASS dev_class; /* peer CoD */ 870 BD_NAME bd_name; /* peer device name */ 871 UINT32 num_val; /* the numeric value for comparison. If just_works, do not show this number to UI */ 872 BOOLEAN just_works; /* TRUE, if "Just Works" association model */ 873 tBTA_AUTH_REQ loc_auth_req; /* Authentication required for local device */ 874 tBTA_AUTH_REQ rmt_auth_req; /* Authentication required for peer device */ 875 tBTA_IO_CAP loc_io_caps; /* IO Capabilities of local device */ 876 tBTA_AUTH_REQ rmt_io_caps; /* IO Capabilities of remote device */ 877 } tBTA_DM_SP_CFM_REQ; 878 879 enum 880 { 881 BTA_SP_KEY_STARTED, /* passkey entry started */ 882 BTA_SP_KEY_ENTERED, /* passkey digit entered */ 883 BTA_SP_KEY_ERASED, /* passkey digit erased */ 884 BTA_SP_KEY_CLEARED, /* passkey cleared */ 885 BTA_SP_KEY_COMPLT /* passkey entry completed */ 886 }; 887 typedef UINT8 tBTA_SP_KEY_TYPE; 888 889 /* Structure associated with BTA_DM_SP_KEYPRESS_EVT */ 890 typedef struct 891 { 892 BD_ADDR bd_addr; /* peer address */ 893 tBTA_SP_KEY_TYPE notif_type; 894 }tBTA_DM_SP_KEY_PRESS; 895 896 /* Structure associated with BTA_DM_SP_KEY_NOTIF_EVT */ 897 typedef struct 898 { 899 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 900 BD_ADDR bd_addr; /* peer address */ 901 DEV_CLASS dev_class; /* peer CoD */ 902 BD_NAME bd_name; /* peer device name */ 903 UINT32 passkey; /* the numeric value for comparison. If just_works, do not show this number to UI */ 904 } tBTA_DM_SP_KEY_NOTIF; 905 906 /* Structure associated with BTA_DM_SP_RMT_OOB_EVT */ 907 typedef struct 908 { 909 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 910 BD_ADDR bd_addr; /* peer address */ 911 DEV_CLASS dev_class; /* peer CoD */ 912 BD_NAME bd_name; /* peer device name */ 913 } tBTA_DM_SP_RMT_OOB; 914 915 /* Structure associated with BTA_DM_BOND_CANCEL_CMPL_EVT */ 916 typedef struct 917 { 918 tBTA_STATUS result; /* TRUE of bond cancel succeeded, FALSE if failed. */ 919 } tBTA_DM_BOND_CANCEL_CMPL; 920 921 /* Union of all security callback structures */ 922 typedef union 923 { 924 tBTA_DM_ENABLE enable; /* BTA enabled */ 925 tBTA_DM_PIN_REQ pin_req; /* PIN request. */ 926 tBTA_DM_AUTH_CMPL auth_cmpl; /* Authentication complete indication. */ 927 tBTA_DM_AUTHORIZE authorize; /* Authorization request. */ 928 tBTA_DM_LINK_UP link_up; /* ACL connection down event */ 929 tBTA_DM_LINK_DOWN link_down; /* ACL connection down event */ 930 tBTA_DM_SIG_STRENGTH sig_strength; /* rssi and link quality value */ 931 tBTA_DM_BUSY_LEVEL busy_level; /* System busy level */ 932 tBTA_DM_SP_CFM_REQ cfm_req; /* user confirm request */ 933 tBTA_DM_SP_KEY_NOTIF key_notif; /* passkey notification */ 934 tBTA_DM_SP_RMT_OOB rmt_oob; /* remote oob */ 935 tBTA_DM_BOND_CANCEL_CMPL bond_cancel_cmpl; /* Bond Cancel Complete indication */ 936 tBTA_DM_SP_KEY_PRESS key_press; /* key press notification event */ 937 tBTA_DM_ROLE_CHG role_chg; /* role change event */ 938 tBTA_DM_BLE_SEC_REQ ble_req; /* BLE SMP related request */ 939 tBTA_DM_BLE_KEY ble_key; /* BLE SMP keys used when pairing */ 940 tBTA_BLE_LOCAL_ID_KEYS ble_id_keys; /* IR event */ 941 BT_OCTET16 ble_er; /* ER event data */ 942 } tBTA_DM_SEC; 943 944 /* Security callback */ 945 typedef void (tBTA_DM_SEC_CBACK)(tBTA_DM_SEC_EVT event, tBTA_DM_SEC *p_data); 946 947 #define BTA_BLE_MULTI_ADV_ILLEGAL 0 948 949 /* multi adv callback event */ 950 #define BTA_BLE_MULTI_ADV_ENB_EVT 1 951 #define BTA_BLE_MULTI_ADV_DISABLE_EVT 2 952 #define BTA_BLE_MULTI_ADV_PARAM_EVT 3 953 #define BTA_BLE_MULTI_ADV_DATA_EVT 4 954 955 typedef UINT8 tBTA_BLE_MULTI_ADV_EVT; 956 957 /* multi adv callback */ 958 typedef void (tBTA_BLE_MULTI_ADV_CBACK)(tBTA_BLE_MULTI_ADV_EVT event, 959 UINT8 inst_id, void *p_ref, tBTA_STATUS status); 960 typedef UINT32 tBTA_DM_BLE_REF_VALUE; 961 962 #define BTA_DM_BLE_PF_ENABLE_EVT BTM_BLE_PF_ENABLE 963 #define BTA_DM_BLE_PF_CONFIG_EVT BTM_BLE_PF_CONFIG 964 typedef UINT8 tBTA_DM_BLE_PF_EVT; 965 966 typedef UINT8 tBTA_DM_BLE_PF_COND_TYPE; 967 968 #define BTA_DM_BLE_PF_LOGIC_OR 0 969 #define BTA_DM_BLE_PF_LOGIC_AND 1 970 typedef UINT8 tBTA_DM_BLE_PF_LOGIC_TYPE; 971 972 #define BTA_DM_BLE_PF_ENABLE 1 973 #define BTA_DM_BLE_PF_CONFIG 2 974 typedef UINT8 tBTA_DM_BLE_PF_ACTION; 975 976 typedef UINT8 tBTA_DM_BLE_PF_FILT_INDEX; 977 978 typedef UINT8 tBTA_DM_BLE_PF_AVBL_SPACE; 979 980 /* Config callback */ 981 typedef void (tBTA_DM_BLE_PF_CFG_CBACK) (tBTA_DM_BLE_PF_ACTION action, 982 tBTA_DM_BLE_PF_COND_TYPE cfg_cond, 983 tBTA_DM_BLE_PF_AVBL_SPACE avbl_space, tBTA_STATUS status, 984 tBTA_DM_BLE_REF_VALUE ref_value); 985 /* Param callback */ 986 typedef void (tBTA_DM_BLE_PF_PARAM_CBACK) (UINT8 action_type, tBTA_DM_BLE_PF_AVBL_SPACE avbl_space, 987 tBTA_DM_BLE_REF_VALUE ref_value, tBTA_STATUS status); 988 989 /* Status callback */ 990 typedef void (tBTA_DM_BLE_PF_STATUS_CBACK) (UINT8 action, tBTA_STATUS status, 991 tBTA_DM_BLE_REF_VALUE ref_value); 992 993 994 #define BTA_DM_BLE_PF_BRDCAST_ADDR_FILT 1 995 #define BTA_DM_BLE_PF_SERV_DATA_CHG_FILT 2 996 #define BTA_DM_BLE_PF_SERV_UUID 4 997 #define BTA_DM_BLE_PF_SERV_SOLC_UUID 8 998 #define BTA_DM_BLE_PF_LOC_NAME_CHECK 16 999 #define BTA_DM_BLE_PF_MANUF_NAME_CHECK 32 1000 #define BTA_DM_BLE_PF_SERV_DATA_CHECK 64 1001 typedef UINT16 tBTA_DM_BLE_PF_FEAT_SEL; 1002 1003 #define BTA_DM_BLE_PF_LIST_LOGIC_OR 1 1004 #define BTA_DM_BLE_PF_LIST_LOGIC_AND 2 1005 typedef UINT16 tBTA_DM_BLE_PF_LIST_LOGIC_TYPE; 1006 1007 #define BTA_DM_BLE_PF_FILT_LOGIC_OR 0 1008 #define BTA_DM_BLE_PF_FILT_LOGIC_AND 1 1009 typedef UINT16 tBTA_DM_BLE_PF_FILT_LOGIC_TYPE; 1010 1011 typedef UINT8 tBTA_DM_BLE_PF_RSSI_THRESHOLD; 1012 typedef UINT8 tBTA_DM_BLE_PF_DELIVERY_MODE; 1013 typedef UINT16 tBTA_DM_BLE_PF_TIMEOUT; 1014 typedef UINT8 tBTA_DM_BLE_PF_TIMEOUT_CNT; 1015 1016 typedef struct 1017 { 1018 tBTA_DM_BLE_PF_FEAT_SEL feat_seln; 1019 tBTA_DM_BLE_PF_LIST_LOGIC_TYPE list_logic_type; 1020 tBTA_DM_BLE_PF_FILT_LOGIC_TYPE filt_logic_type; 1021 tBTA_DM_BLE_PF_RSSI_THRESHOLD rssi_high_thres; 1022 tBTA_DM_BLE_PF_RSSI_THRESHOLD rssi_low_thres; 1023 tBTA_DM_BLE_PF_DELIVERY_MODE dely_mode; 1024 tBTA_DM_BLE_PF_TIMEOUT found_timeout; 1025 tBTA_DM_BLE_PF_TIMEOUT lost_timeout; 1026 tBTA_DM_BLE_PF_TIMEOUT_CNT found_timeout_cnt; 1027 } tBTA_DM_BLE_PF_FILT_PARAMS; 1028 1029 /* Vendor Specific Command Callback */ 1030 typedef tBTM_VSC_CMPL_CB tBTA_VENDOR_CMPL_CBACK; 1031 1032 /* Search callback events */ 1033 #define BTA_DM_INQ_RES_EVT 0 /* Inquiry result for a peer device. */ 1034 #define BTA_DM_INQ_CMPL_EVT 1 /* Inquiry complete. */ 1035 #define BTA_DM_DISC_RES_EVT 2 /* Discovery result for a peer device. */ 1036 #define BTA_DM_DISC_BLE_RES_EVT 3 /* Discovery result for BLE GATT based servoce on a peer device. */ 1037 #define BTA_DM_DISC_CMPL_EVT 4 /* Discovery complete. */ 1038 #define BTA_DM_DI_DISC_CMPL_EVT 5 /* Discovery complete. */ 1039 #define BTA_DM_SEARCH_CANCEL_CMPL_EVT 6 /* Search cancelled */ 1040 1041 typedef UINT8 tBTA_DM_SEARCH_EVT; 1042 1043 #define BTA_DM_INQ_RES_IGNORE_RSSI BTM_INQ_RES_IGNORE_RSSI /* 0x7f RSSI value not supplied (ignore it) */ 1044 1045 /* Structure associated with BTA_DM_INQ_RES_EVT */ 1046 typedef struct 1047 { 1048 BD_ADDR bd_addr; /* BD address peer device. */ 1049 DEV_CLASS dev_class; /* Device class of peer device. */ 1050 BOOLEAN remt_name_not_required; /* Application sets this flag if it already knows the name of the device */ 1051 /* If the device name is known to application BTA skips the remote name request */ 1052 BOOLEAN is_limited; /* TRUE, if the limited inquiry bit is set in the CoD */ 1053 INT8 rssi; /* The rssi value */ 1054 UINT8 *p_eir; /* received EIR */ 1055 #if (BLE_INCLUDED == TRUE) 1056 UINT8 inq_result_type; 1057 UINT8 ble_addr_type; 1058 tBTM_BLE_EVT_TYPE ble_evt_type; 1059 tBT_DEVICE_TYPE device_type; 1060 UINT8 flag; 1061 #endif 1062 1063 } tBTA_DM_INQ_RES; 1064 1065 /* Structure associated with BTA_DM_INQ_CMPL_EVT */ 1066 typedef struct 1067 { 1068 UINT8 num_resps; /* Number of inquiry responses. */ 1069 } tBTA_DM_INQ_CMPL; 1070 1071 /* Structure associated with BTA_DM_DI_DISC_CMPL_EVT */ 1072 typedef struct 1073 { 1074 BD_ADDR bd_addr; /* BD address peer device. */ 1075 UINT8 num_record; /* Number of DI record */ 1076 tBTA_STATUS result; 1077 } tBTA_DM_DI_DISC_CMPL; 1078 1079 /* Structure associated with BTA_DM_DISC_RES_EVT */ 1080 typedef struct 1081 { 1082 BD_ADDR bd_addr; /* BD address peer device. */ 1083 BD_NAME bd_name; /* Name of peer device. */ 1084 tBTA_SERVICE_MASK services; /* Services found on peer device. */ 1085 // btla-specific ++ 1086 UINT8 * p_raw_data; /* Raw data for discovery DB */ 1087 UINT32 raw_data_size; /* size of raw data */ 1088 tBT_DEVICE_TYPE device_type; /* device type in case it is BLE device */ 1089 UINT32 num_uuids; 1090 UINT8 *p_uuid_list; 1091 // btla-specific -- 1092 tBTA_STATUS result; 1093 } tBTA_DM_DISC_RES; 1094 1095 /* Structure associated with tBTA_DM_DISC_BLE_RES */ 1096 typedef struct 1097 { 1098 BD_ADDR bd_addr; /* BD address peer device. */ 1099 BD_NAME bd_name; /* Name of peer device. */ 1100 tBT_UUID service; /* GATT based Services UUID found on peer device. */ 1101 } tBTA_DM_DISC_BLE_RES; 1102 1103 1104 /* Union of all search callback structures */ 1105 typedef union 1106 { 1107 tBTA_DM_INQ_RES inq_res; /* Inquiry result for a peer device. */ 1108 tBTA_DM_INQ_CMPL inq_cmpl; /* Inquiry complete. */ 1109 tBTA_DM_DISC_RES disc_res; /* Discovery result for a peer device. */ 1110 tBTA_DM_DISC_BLE_RES disc_ble_res; /* discovery result for GATT based service */ 1111 tBTA_DM_DI_DISC_CMPL di_disc; /* DI discovery result for a peer device */ 1112 1113 } tBTA_DM_SEARCH; 1114 1115 /* Search callback */ 1116 typedef void (tBTA_DM_SEARCH_CBACK)(tBTA_DM_SEARCH_EVT event, tBTA_DM_SEARCH *p_data); 1117 1118 /* Execute call back */ 1119 typedef void (tBTA_DM_EXEC_CBACK) (void * p_param); 1120 1121 /* Encryption callback*/ 1122 typedef void (tBTA_DM_ENCRYPT_CBACK) (BD_ADDR bd_addr, tBTA_TRANSPORT transport, tBTA_STATUS result); 1123 1124 #if BLE_INCLUDED == TRUE 1125 #define BTA_DM_BLE_SEC_NONE BTM_BLE_SEC_NONE 1126 #define BTA_DM_BLE_SEC_ENCRYPT BTM_BLE_SEC_ENCRYPT 1127 #define BTA_DM_BLE_SEC_NO_MITM BTM_BLE_SEC_ENCRYPT_NO_MITM 1128 #define BTA_DM_BLE_SEC_MITM BTM_BLE_SEC_ENCRYPT_MITM 1129 typedef tBTM_BLE_SEC_ACT tBTA_DM_BLE_SEC_ACT; 1130 1131 typedef tBTM_BLE_TX_TIME_MS tBTA_DM_BLE_TX_TIME_MS; 1132 typedef tBTM_BLE_RX_TIME_MS tBTA_DM_BLE_RX_TIME_MS; 1133 typedef tBTM_BLE_IDLE_TIME_MS tBTA_DM_BLE_IDLE_TIME_MS; 1134 typedef tBTM_BLE_ENERGY_USED tBTA_DM_BLE_ENERGY_USED; 1135 1136 #define BTA_DM_CONTRL_UNKNOWN 0 /* Unknown state */ 1137 #define BTA_DM_CONTRL_ACTIVE 1 /* ACL link on, SCO link ongoing, sniff mode */ 1138 #define BTA_DM_CONTRL_SCAN 2 /* Scan state - paging/inquiry/trying to connect*/ 1139 #define BTA_DM_CONTRL_IDLE 3 /* Idle state - page scan, LE advt, inquiry scan */ 1140 1141 typedef UINT8 tBTA_DM_CONTRL_STATE; 1142 1143 1144 typedef void (tBTA_BLE_SCAN_THRESHOLD_CBACK)(tBTA_DM_BLE_REF_VALUE ref_value); 1145 1146 typedef void (tBTA_BLE_SCAN_REP_CBACK) (tBTA_DM_BLE_REF_VALUE ref_value, UINT8 report_format, 1147 UINT8 num_records, UINT16 data_len, 1148 UINT8* p_rep_data, tBTA_STATUS status); 1149 1150 typedef void (tBTA_BLE_SCAN_SETUP_CBACK) (tBTA_BLE_BATCH_SCAN_EVT evt, 1151 tBTA_DM_BLE_REF_VALUE ref_value, 1152 tBTA_STATUS status); 1153 1154 typedef void (tBTA_BLE_TRACK_ADV_CMPL_CBACK)(int action, tBTA_STATUS status, 1155 tBTA_DM_BLE_PF_AVBL_SPACE avbl_space, 1156 tBTA_DM_BLE_REF_VALUE ref_value); 1157 1158 typedef void (tBTA_BLE_TRACK_ADV_CBACK)(int filt_index, tBLE_ADDR_TYPE addr_type, BD_ADDR bda, 1159 int adv_state, tBTA_DM_BLE_REF_VALUE ref_value); 1160 1161 typedef void (tBTA_BLE_ENERGY_INFO_CBACK)(tBTA_DM_BLE_TX_TIME_MS tx_time, 1162 tBTA_DM_BLE_RX_TIME_MS rx_time, 1163 tBTA_DM_BLE_IDLE_TIME_MS idle_time, 1164 tBTA_DM_BLE_ENERGY_USED energy_used, 1165 tBTA_DM_CONTRL_STATE ctrl_state, 1166 tBTA_STATUS status); 1167 1168 #else 1169 typedef UINT8 tBTA_DM_BLE_SEC_ACT; 1170 #endif 1171 1172 /* Maximum service name length */ 1173 #define BTA_SERVICE_NAME_LEN 35 1174 #define BTA_SERVICE_DESP_LEN BTA_SERVICE_NAME_LEN 1175 #define BTA_PROVIDER_NAME_LEN BTA_SERVICE_NAME_LEN 1176 1177 1178 /* link policy masks */ 1179 #define BTA_DM_LP_SWITCH HCI_ENABLE_MASTER_SLAVE_SWITCH 1180 #define BTA_DM_LP_HOLD HCI_ENABLE_HOLD_MODE 1181 #define BTA_DM_LP_SNIFF HCI_ENABLE_SNIFF_MODE 1182 #define BTA_DM_LP_PARK HCI_ENABLE_PARK_MODE 1183 typedef UINT16 tBTA_DM_LP_MASK; 1184 1185 /* power mode actions */ 1186 #define BTA_DM_PM_NO_ACTION 0x00 /* no change to the current pm setting */ 1187 #define BTA_DM_PM_PARK 0x10 /* prefers park mode */ 1188 #define BTA_DM_PM_SNIFF 0x20 /* prefers sniff mode */ 1189 #define BTA_DM_PM_SNIFF1 0x21 /* prefers sniff1 mode */ 1190 #define BTA_DM_PM_SNIFF2 0x22 /* prefers sniff2 mode */ 1191 #define BTA_DM_PM_SNIFF3 0x23 /* prefers sniff3 mode */ 1192 #define BTA_DM_PM_SNIFF4 0x24 /* prefers sniff4 mode */ 1193 #define BTA_DM_PM_SNIFF5 0x25 /* prefers sniff5 mode */ 1194 #define BTA_DM_PM_SNIFF6 0x26 /* prefers sniff6 mode */ 1195 #define BTA_DM_PM_SNIFF7 0x27 /* prefers sniff7 mode */ 1196 #define BTA_DM_PM_SNIFF_USER0 0x28 /* prefers user-defined sniff0 mode (testtool only) */ 1197 #define BTA_DM_PM_SNIFF_USER1 0x29 /* prefers user-defined sniff1 mode (testtool only) */ 1198 #define BTA_DM_PM_ACTIVE 0x40 /* prefers active mode */ 1199 #define BTA_DM_PM_RETRY 0x80 /* retry power mode based on current settings */ 1200 #define BTA_DM_PM_NO_PREF 0x01 /* service has no prefernce on power mode setting. eg. connection to service got closed */ 1201 1202 typedef UINT8 tBTA_DM_PM_ACTTION; 1203 1204 /* index to bta_dm_ssr_spec */ 1205 #define BTA_DM_PM_SSR0 0 1206 #define BTA_DM_PM_SSR1 1 /* BTA_DM_PM_SSR1 will be dedicated for 1207 HH SSR setting entry, no other profile can use it */ 1208 #define BTA_DM_PM_SSR2 2 1209 #define BTA_DM_PM_SSR3 3 1210 #define BTA_DM_PM_SSR4 4 1211 #define BTA_DM_PM_SSR5 5 1212 #define BTA_DM_PM_SSR6 6 1213 1214 #define BTA_DM_PM_NUM_EVTS 9 1215 1216 #ifndef BTA_DM_PM_PARK_IDX 1217 #define BTA_DM_PM_PARK_IDX 5 /* the actual index to bta_dm_pm_md[] for PARK mode */ 1218 #endif 1219 1220 #ifndef BTA_DM_PM_SNIFF_A2DP_IDX 1221 #define BTA_DM_PM_SNIFF_A2DP_IDX BTA_DM_PM_SNIFF 1222 #endif 1223 1224 #ifndef BTA_DM_PM_SNIFF_HD_IDLE_IDX 1225 #define BTA_DM_PM_SNIFF_HD_IDLE_IDX BTA_DM_PM_SNIFF2 1226 #endif 1227 1228 #ifndef BTA_DM_PM_SNIFF_SCO_OPEN_IDX 1229 #define BTA_DM_PM_SNIFF_SCO_OPEN_IDX BTA_DM_PM_SNIFF3 1230 #endif 1231 1232 #ifndef BTA_DM_PM_SNIFF_HD_ACTIVE_IDX 1233 #define BTA_DM_PM_SNIFF_HD_ACTIVE_IDX BTA_DM_PM_SNIFF4 1234 #endif 1235 1236 #ifndef BTA_DM_PM_SNIFF_HH_OPEN_IDX 1237 #define BTA_DM_PM_SNIFF_HH_OPEN_IDX BTA_DM_PM_SNIFF2 1238 #endif 1239 1240 #ifndef BTA_DM_PM_SNIFF_HH_ACTIVE_IDX 1241 #define BTA_DM_PM_SNIFF_HH_ACTIVE_IDX BTA_DM_PM_SNIFF2 1242 #endif 1243 1244 #ifndef BTA_DM_PM_SNIFF_HH_IDLE_IDX 1245 #define BTA_DM_PM_SNIFF_HH_IDLE_IDX BTA_DM_PM_SNIFF2 1246 #endif 1247 1248 1249 #ifndef BTA_DM_PM_HH_OPEN_DELAY 1250 #define BTA_DM_PM_HH_OPEN_DELAY 30000 1251 #endif 1252 1253 #ifndef BTA_DM_PM_HH_ACTIVE_DELAY 1254 #define BTA_DM_PM_HH_ACTIVE_DELAY 30000 1255 #endif 1256 1257 #ifndef BTA_DM_PM_HH_IDLE_DELAY 1258 #define BTA_DM_PM_HH_IDLE_DELAY 30000 1259 #endif 1260 1261 /* The Sniff Parameters defined below must be ordered from highest 1262 * latency (biggest interval) to lowest latency. If there is a conflict 1263 * among the connected services the setting with the lowest latency will 1264 * be selected. If a device should override a sniff parameter then it 1265 * must insure that order is maintained. 1266 */ 1267 #ifndef BTA_DM_PM_SNIFF_MAX 1268 #define BTA_DM_PM_SNIFF_MAX 800 1269 #define BTA_DM_PM_SNIFF_MIN 400 1270 #define BTA_DM_PM_SNIFF_ATTEMPT 4 1271 #define BTA_DM_PM_SNIFF_TIMEOUT 1 1272 #endif 1273 1274 #ifndef BTA_DM_PM_SNIFF1_MAX 1275 #define BTA_DM_PM_SNIFF1_MAX 400 1276 #define BTA_DM_PM_SNIFF1_MIN 200 1277 #define BTA_DM_PM_SNIFF1_ATTEMPT 4 1278 #define BTA_DM_PM_SNIFF1_TIMEOUT 1 1279 #endif 1280 1281 #ifndef BTA_DM_PM_SNIFF2_MAX 1282 #define BTA_DM_PM_SNIFF2_MAX 180 1283 #define BTA_DM_PM_SNIFF2_MIN 150 1284 #define BTA_DM_PM_SNIFF2_ATTEMPT 4 1285 #define BTA_DM_PM_SNIFF2_TIMEOUT 1 1286 #endif 1287 1288 #ifndef BTA_DM_PM_SNIFF3_MAX 1289 #define BTA_DM_PM_SNIFF3_MAX 150 1290 #define BTA_DM_PM_SNIFF3_MIN 50 1291 #define BTA_DM_PM_SNIFF3_ATTEMPT 4 1292 #define BTA_DM_PM_SNIFF3_TIMEOUT 1 1293 #endif 1294 1295 #ifndef BTA_DM_PM_SNIFF4_MAX 1296 #define BTA_DM_PM_SNIFF4_MAX 54 1297 #define BTA_DM_PM_SNIFF4_MIN 30 1298 #define BTA_DM_PM_SNIFF4_ATTEMPT 4 1299 #define BTA_DM_PM_SNIFF4_TIMEOUT 1 1300 #endif 1301 1302 #ifndef BTA_DM_PM_PARK_MAX 1303 #define BTA_DM_PM_PARK_MAX 800 1304 #define BTA_DM_PM_PARK_MIN 400 1305 #define BTA_DM_PM_PARK_ATTEMPT 0 1306 #define BTA_DM_PM_PARK_TIMEOUT 0 1307 #endif 1308 1309 1310 /* Switch callback events */ 1311 #define BTA_DM_SWITCH_CMPL_EVT 0 /* Completion of the Switch API */ 1312 1313 typedef UINT8 tBTA_DM_SWITCH_EVT; 1314 typedef void (tBTA_DM_SWITCH_CBACK)(tBTA_DM_SWITCH_EVT event, tBTA_STATUS status); 1315 1316 /* Audio routing out configuration */ 1317 #define BTA_DM_ROUTE_NONE 0x00 /* No Audio output */ 1318 #define BTA_DM_ROUTE_DAC 0x01 /* routing over analog output */ 1319 #define BTA_DM_ROUTE_I2S 0x02 /* routing over digital (I2S) output */ 1320 #define BTA_DM_ROUTE_BT_MONO 0x04 /* routing over SCO */ 1321 #define BTA_DM_ROUTE_BT_STEREO 0x08 /* routing over BT Stereo */ 1322 #define BTA_DM_ROUTE_HOST 0x10 /* routing over Host */ 1323 #define BTA_DM_ROUTE_FMTX 0x20 /* routing over FMTX */ 1324 #define BTA_DM_ROUTE_FMRX 0x40 /* routing over FMRX */ 1325 #define BTA_DM_ROUTE_BTSNK 0x80 /* routing over BT SNK */ 1326 1327 typedef UINT8 tBTA_DM_ROUTE_PATH; 1328 1329 1330 /* Device Identification (DI) data structure 1331 */ 1332 /* Used to set the DI record */ 1333 typedef tSDP_DI_RECORD tBTA_DI_RECORD; 1334 /* Used to get the DI record */ 1335 typedef tSDP_DI_GET_RECORD tBTA_DI_GET_RECORD; 1336 /* SDP discovery database */ 1337 typedef tSDP_DISCOVERY_DB tBTA_DISCOVERY_DB; 1338 1339 #ifndef BTA_DI_NUM_MAX 1340 #define BTA_DI_NUM_MAX 3 1341 #endif 1342 1343 /* Device features mask definitions */ 1344 #define BTA_FEATURE_BYTES_PER_PAGE BTM_FEATURE_BYTES_PER_PAGE 1345 #define BTA_EXT_FEATURES_PAGE_MAX BTM_EXT_FEATURES_PAGE_MAX 1346 /* ACL type 1347 */ 1348 #define BTA_DM_LINK_TYPE_BR_EDR 0x01 1349 #define BTA_DM_LINK_TYPE_LE 0x02 1350 #define BTA_DM_LINK_TYPE_ALL 0xFF 1351 typedef UINT8 tBTA_DM_LINK_TYPE; 1352 1353 #define IMMEDIATE_DELY_MODE 0x00 1354 #define ONFOUND_DELY_MODE 0x01 1355 #define BATCH_DELY_MODE 0x02 1356 #define ALLOW_ALL_FILTER 0x00 1357 #define LOWEST_RSSI_VALUE 129 1358 1359 /***************************************************************************** 1360 ** External Function Declarations 1361 *****************************************************************************/ 1362 #ifdef __cplusplus 1363 extern "C" 1364 { 1365 #endif 1366 1367 /******************************************************************************* 1368 ** 1369 ** Function BTA_EnableBluetooth 1370 ** 1371 ** Description This function initializes BTA and prepares BTA and the 1372 ** Bluetooth protocol stack for use. This function is 1373 ** typically called at startup or when Bluetooth services 1374 ** are required by the phone. This function must be called 1375 ** before calling any other API function. 1376 ** 1377 ** 1378 ** Returns BTA_SUCCESS if successful. 1379 ** BTA_FAIL if internal failure. 1380 ** 1381 *******************************************************************************/ 1382 BTA_API extern tBTA_STATUS BTA_EnableBluetooth(tBTA_DM_SEC_CBACK *p_cback); 1383 1384 /******************************************************************************* 1385 ** 1386 ** Function BTA_DisableBluetooth 1387 ** 1388 ** Description This function disables BTA and the Bluetooth protocol 1389 ** stack. It is called when BTA is no longer being used 1390 ** by any application in the system. 1391 ** 1392 ** 1393 ** Returns void 1394 ** 1395 *******************************************************************************/ 1396 BTA_API extern tBTA_STATUS BTA_DisableBluetooth(void); 1397 1398 /******************************************************************************* 1399 ** 1400 ** Function BTA_EnableTestMode 1401 ** 1402 ** Description Enables bluetooth device under test mode 1403 ** 1404 ** 1405 ** Returns tBTA_STATUS 1406 ** 1407 *******************************************************************************/ 1408 BTA_API extern tBTA_STATUS BTA_EnableTestMode(void); 1409 1410 /******************************************************************************* 1411 ** 1412 ** Function BTA_DisableTestMode 1413 ** 1414 ** Description Disable bluetooth device under test mode 1415 ** 1416 ** 1417 ** Returns None 1418 ** 1419 *******************************************************************************/ 1420 BTA_API extern void BTA_DisableTestMode(void); 1421 1422 /******************************************************************************* 1423 ** 1424 ** Function BTA_DmIsDeviceUp 1425 ** 1426 ** Description This function tests whether the Bluetooth module is up 1427 ** and ready. This is a direct execution function that 1428 ** may lock task scheduling on some platforms. 1429 ** 1430 ** 1431 ** Returns TRUE if the module is ready. 1432 ** FALSE if the module is not ready. 1433 ** 1434 *******************************************************************************/ 1435 BTA_API extern BOOLEAN BTA_DmIsDeviceUp(void); 1436 1437 /******************************************************************************* 1438 ** 1439 ** Function BTA_DmSetDeviceName 1440 ** 1441 ** Description This function sets the Bluetooth name of the local device. 1442 ** 1443 ** 1444 ** Returns void 1445 ** 1446 *******************************************************************************/ 1447 BTA_API extern void BTA_DmSetDeviceName(char *p_name); 1448 1449 /******************************************************************************* 1450 ** 1451 ** Function BTA_DmSetVisibility 1452 ** 1453 ** Description This function sets the Bluetooth connectable,discoverable, 1454 ** pairable and conn paired only modesmodes of the local device. 1455 ** This controls whether other Bluetooth devices can find and connect to 1456 ** the local device. 1457 ** 1458 ** 1459 ** Returns void 1460 ** 1461 *******************************************************************************/ 1462 BTA_API extern void BTA_DmSetVisibility(tBTA_DM_DISC disc_mode, tBTA_DM_CONN conn_mode, UINT8 pairable_mode, UINT8 conn_filter); 1463 1464 /******************************************************************************* 1465 ** 1466 ** Function BTA_DmSetScanParam 1467 ** 1468 ** Description This function sets the parameters for page scan and 1469 ** inquiry scan. 1470 ** 1471 ** 1472 ** Returns void 1473 ** 1474 *******************************************************************************/ 1475 BTA_API extern void BTA_DmSetScanParam (UINT16 page_scan_interval, UINT16 page_scan_window, 1476 UINT16 inquiry_scan_interval, UINT16 inquiry_scan_window); 1477 1478 /******************************************************************************* 1479 ** 1480 ** Function BTA_DmSetAfhChannels 1481 ** 1482 ** Description This function sets the AFH first and 1483 ** last disable channel, so channels within 1484 ** that range are disabled. 1485 ** In order to use this API, BTM_BYPASS_AMP_AUTO_AFH must be set 1486 ** to be TRUE 1487 ** 1488 ** Returns void 1489 ** 1490 *******************************************************************************/ 1491 BTA_API extern void BTA_DmSetAfhChannels(UINT8 first, UINT8 last); 1492 1493 1494 /******************************************************************************* 1495 ** 1496 ** Function BTA_DmVendorSpecificCommand 1497 ** 1498 ** Description This function sends the vendor specific command 1499 ** to the controller 1500 ** 1501 ** 1502 ** Returns tBTA_STATUS 1503 ** 1504 *******************************************************************************/ 1505 BTA_API extern tBTA_STATUS BTA_DmVendorSpecificCommand (UINT16 opcode, UINT8 param_len,UINT8 *p_param_buf, tBTA_VENDOR_CMPL_CBACK *p_cback); 1506 1507 1508 /******************************************************************************* 1509 ** 1510 ** Function BTA_DmSearch 1511 ** 1512 ** Description This function searches for peer Bluetooth devices. It 1513 ** first performs an inquiry; for each device found from the 1514 ** inquiry it gets the remote name of the device. If 1515 ** parameter services is nonzero, service discovery will be 1516 ** performed on each device for the services specified. 1517 ** 1518 ** 1519 ** Returns void 1520 ** 1521 *******************************************************************************/ 1522 BTA_API extern void BTA_DmSearch(tBTA_DM_INQ *p_dm_inq, tBTA_SERVICE_MASK services, 1523 tBTA_DM_SEARCH_CBACK *p_cback); 1524 1525 /******************************************************************************* 1526 ** 1527 ** Function BTA_DmSearchCancel 1528 ** 1529 ** Description This function cancels a search that has been initiated 1530 ** by calling BTA_DmSearch(). 1531 ** 1532 ** 1533 ** Returns void 1534 ** 1535 *******************************************************************************/ 1536 BTA_API extern void BTA_DmSearchCancel(void); 1537 1538 /******************************************************************************* 1539 ** 1540 ** Function BTA_DmDiscover 1541 ** 1542 ** Description This function performs service discovery for the services 1543 ** of a particular peer device. 1544 ** 1545 ** 1546 ** Returns void 1547 ** 1548 *******************************************************************************/ 1549 BTA_API extern void BTA_DmDiscover(BD_ADDR bd_addr, tBTA_SERVICE_MASK services, 1550 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search); 1551 1552 // btla-specific ++ 1553 /******************************************************************************* 1554 ** 1555 ** Function BTA_DmDiscoverUUID 1556 ** 1557 ** Description This function performs service discovery for the services 1558 ** of a particular peer device. 1559 ** 1560 ** 1561 ** Returns void 1562 ** 1563 *******************************************************************************/ 1564 BTA_API extern void BTA_DmDiscoverUUID(BD_ADDR bd_addr, tSDP_UUID *uuid, 1565 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search); 1566 1567 /******************************************************************************* 1568 ** 1569 ** Function BTA_DmGetCachedRemoteName 1570 ** 1571 ** Description Retieve cached remote name if available 1572 ** 1573 ** Returns BTA_SUCCESS if cached name was retrieved 1574 ** BTA_FAILURE if cached name is not available 1575 ** 1576 *******************************************************************************/ 1577 tBTA_STATUS BTA_DmGetCachedRemoteName(BD_ADDR remote_device, UINT8 **pp_cached_name); 1578 // btla-specific -- 1579 1580 /******************************************************************************* 1581 ** 1582 ** Function BTA_DmIsMaster 1583 ** 1584 ** Description This function checks if the local device is the master of 1585 ** the link to the given device 1586 ** 1587 ** Returns TRUE if master. 1588 ** FALSE if not. 1589 ** 1590 *******************************************************************************/ 1591 BTA_API extern BOOLEAN BTA_DmIsMaster(BD_ADDR bd_addr); 1592 1593 /******************************************************************************* 1594 ** 1595 ** Function BTA_DmBond 1596 ** 1597 ** Description This function initiates a bonding procedure with a peer 1598 ** device. The bonding procedure enables authentication 1599 ** and optionally encryption on the Bluetooth link. 1600 ** 1601 ** 1602 ** Returns void 1603 ** 1604 *******************************************************************************/ 1605 BTA_API extern void BTA_DmBond(BD_ADDR bd_addr); 1606 1607 /******************************************************************************* 1608 ** 1609 ** Function BTA_DmBondByTransport 1610 ** 1611 ** Description This function initiates a bonding procedure with a peer 1612 ** device by designated transport. The bonding procedure enables 1613 ** authentication and optionally encryption on the Bluetooth link. 1614 ** 1615 ** 1616 ** Returns void 1617 ** 1618 *******************************************************************************/ 1619 BTA_API extern void BTA_DmBondByTransport(BD_ADDR bd_addr, tBTA_TRANSPORT transport); 1620 1621 1622 /******************************************************************************* 1623 ** 1624 ** Function BTA_DmBondCancel 1625 ** 1626 ** Description This function cancels a bonding procedure with a peer 1627 ** device. 1628 ** 1629 ** 1630 ** Returns void 1631 ** 1632 *******************************************************************************/ 1633 BTA_API extern void BTA_DmBondCancel(BD_ADDR bd_addr); 1634 1635 /******************************************************************************* 1636 ** 1637 ** Function BTA_DmPinReply 1638 ** 1639 ** Description This function provides a PIN when one is requested by DM 1640 ** during a bonding procedure. The application should call 1641 ** this function after the security callback is called with 1642 ** a BTA_DM_PIN_REQ_EVT. 1643 ** 1644 ** 1645 ** Returns void 1646 ** 1647 *******************************************************************************/ 1648 BTA_API extern void BTA_DmPinReply(BD_ADDR bd_addr, BOOLEAN accept, UINT8 pin_len, 1649 UINT8 *p_pin); 1650 1651 /******************************************************************************* 1652 ** 1653 ** Function BTA_DmLinkPolicy 1654 ** 1655 ** Description This function sets/clears the link policy mask to the given 1656 ** bd_addr. 1657 ** If clearing the sniff or park mode mask, the link is put 1658 ** in active mode. 1659 ** 1660 ** Returns void 1661 ** 1662 *******************************************************************************/ 1663 BTA_API extern void BTA_DmLinkPolicy(BD_ADDR bd_addr, tBTA_DM_LP_MASK policy_mask, 1664 BOOLEAN set); 1665 1666 #if (BTM_OOB_INCLUDED == TRUE) 1667 /******************************************************************************* 1668 ** 1669 ** Function BTA_DmLocalOob 1670 ** 1671 ** Description This function retrieves the OOB data from local controller. 1672 ** The result is reported by bta_dm_co_loc_oob(). 1673 ** 1674 ** Returns void 1675 ** 1676 *******************************************************************************/ 1677 BTA_API extern void BTA_DmLocalOob(void); 1678 #endif /* BTM_OOB_INCLUDED */ 1679 1680 /******************************************************************************* 1681 ** 1682 ** Function BTA_DmConfirm 1683 ** 1684 ** Description This function accepts or rejects the numerical value of the 1685 ** Simple Pairing process on BTA_DM_SP_CFM_REQ_EVT 1686 ** 1687 ** Returns void 1688 ** 1689 *******************************************************************************/ 1690 BTA_API extern void BTA_DmConfirm(BD_ADDR bd_addr, BOOLEAN accept); 1691 1692 /******************************************************************************* 1693 ** 1694 ** Function BTA_DmPasskeyCancel 1695 ** 1696 ** Description This function is called to cancel the simple pairing process 1697 ** reported by BTA_DM_SP_KEY_NOTIF_EVT 1698 ** 1699 ** Returns void 1700 ** 1701 *******************************************************************************/ 1702 BTA_API extern void BTA_DmPasskeyCancel(BD_ADDR bd_addr); 1703 1704 /******************************************************************************* 1705 ** 1706 ** Function BTA_DmAddDevice 1707 ** 1708 ** Description This function adds a device to the security database list 1709 ** of peer devices. This function would typically be called 1710 ** at system startup to initialize the security database with 1711 ** known peer devices. This is a direct execution function 1712 ** that may lock task scheduling on some platforms. 1713 ** 1714 ** Returns void 1715 ** 1716 *******************************************************************************/ 1717 BTA_API extern void BTA_DmAddDevice(BD_ADDR bd_addr, DEV_CLASS dev_class, 1718 LINK_KEY link_key, tBTA_SERVICE_MASK trusted_mask, 1719 BOOLEAN is_trusted, UINT8 key_type, 1720 tBTA_IO_CAP io_cap); 1721 1722 /******************************************************************************* 1723 ** 1724 ** Function BTA_DmAddDevWithName 1725 ** 1726 ** Description This function is newer version of BTA_DmAddDevice() 1727 ** which added bd_name and features as input parameters. 1728 ** 1729 ** 1730 ** Returns void 1731 ** 1732 ** Note: features points to the remote device features array. 1733 ** The array size is 1734 ** BTA_FEATURE_BYTES_PER_PAGE * (BTA_EXT_FEATURES_PAGE_MAX + 1) 1735 ** 1736 *******************************************************************************/ 1737 BTA_API extern void BTA_DmAddDevWithName (BD_ADDR bd_addr, DEV_CLASS dev_class, 1738 BD_NAME bd_name, UINT8 *features, 1739 LINK_KEY link_key, tBTA_SERVICE_MASK trusted_mask, 1740 BOOLEAN is_trusted, UINT8 key_type, tBTA_IO_CAP io_cap); 1741 1742 /******************************************************************************* 1743 ** 1744 ** Function BTA_DmRemoveDevice 1745 ** 1746 ** Description This function removes a device from the security database. 1747 ** This is a direct execution function that may lock task 1748 ** scheduling on some platforms. 1749 ** 1750 ** 1751 ** Returns BTA_SUCCESS if successful. 1752 ** BTA_FAIL if operation failed. 1753 ** 1754 *******************************************************************************/ 1755 BTA_API extern tBTA_STATUS BTA_DmRemoveDevice(BD_ADDR bd_addr); 1756 1757 /******************************************************************************* 1758 ** 1759 ** Function BTA_DmAuthorizeReply 1760 ** 1761 ** Description This function provides an authorization reply when 1762 ** authorization is requested by BTA. The application calls 1763 ** this function after the security callback is called with 1764 ** a BTA_DM_AUTHORIZE_EVT. 1765 ** 1766 ** 1767 ** Returns void 1768 ** 1769 *******************************************************************************/ 1770 BTA_API extern void BTA_DmAuthorizeReply(BD_ADDR bd_addr, tBTA_SERVICE_ID service, 1771 tBTA_AUTH_RESP response); 1772 1773 /******************************************************************************* 1774 ** 1775 ** Function BTA_DmSignalStrength 1776 ** 1777 ** Description This function initiates RSSI and channnel quality 1778 ** measurments. BTA_DM_SIG_STRENGTH_EVT is sent to 1779 ** application with the values of RSSI and channel 1780 ** quality 1781 ** 1782 ** 1783 ** Returns void 1784 ** 1785 *******************************************************************************/ 1786 BTA_API extern void BTA_DmSignalStrength(tBTA_SIG_STRENGTH_MASK mask, UINT16 period, BOOLEAN start); 1787 1788 /******************************************************************************* 1789 ** 1790 ** Function BTA_DmWriteInqTxPower 1791 ** 1792 ** Description This command is used to write the inquiry transmit power level 1793 ** used to transmit the inquiry (ID) data packets. 1794 ** 1795 ** Parameters tx_power - tx inquiry power to use, valid value is -70 ~ 20 1796 1797 ** Returns void 1798 ** 1799 *******************************************************************************/ 1800 BTA_API extern void BTA_DmWriteInqTxPower(INT8 tx_power); 1801 1802 /******************************************************************************* 1803 ** 1804 ** Function BTA_DmEirAddUUID 1805 ** 1806 ** Description This function is called to add UUID into EIR. 1807 ** 1808 ** Parameters tBT_UUID - UUID 1809 ** 1810 ** Returns None 1811 ** 1812 *******************************************************************************/ 1813 BTA_API extern void BTA_DmEirAddUUID (tBT_UUID *p_uuid); 1814 1815 /******************************************************************************* 1816 ** 1817 ** Function BTA_DmEirRemoveUUID 1818 ** 1819 ** Description This function is called to remove UUID from EIR. 1820 ** 1821 ** Parameters tBT_UUID - UUID 1822 ** 1823 ** Returns None 1824 ** 1825 *******************************************************************************/ 1826 BTA_API extern void BTA_DmEirRemoveUUID (tBT_UUID *p_uuid); 1827 1828 /******************************************************************************* 1829 ** 1830 ** Function BTA_DmSetEIRConfig 1831 ** 1832 ** Description This function is called to override the BTA default EIR parameters. 1833 ** This funciton is only valid in a system where BTU & App task 1834 ** are in the same memory space. 1835 ** 1836 ** Parameters Pointer to User defined EIR config 1837 ** 1838 ** Returns None 1839 ** 1840 *******************************************************************************/ 1841 BTA_API extern void BTA_DmSetEIRConfig (tBTA_DM_EIR_CONF *p_eir_cfg); 1842 1843 /******************************************************************************* 1844 ** 1845 ** Function BTA_CheckEirData 1846 ** 1847 ** Description This function is called to get EIR data from significant part. 1848 ** 1849 ** Parameters p_eir - pointer of EIR significant part 1850 ** type - finding EIR data type 1851 ** p_length - return the length of EIR data 1852 ** 1853 ** Returns pointer of EIR data 1854 ** 1855 *******************************************************************************/ 1856 BTA_API extern UINT8 *BTA_CheckEirData( UINT8 *p_eir, UINT8 tag, UINT8 *p_length ); 1857 1858 /******************************************************************************* 1859 ** 1860 ** Function BTA_GetEirService 1861 ** 1862 ** Description This function is called to get BTA service mask from EIR. 1863 ** 1864 ** Parameters p_eir - pointer of EIR significant part 1865 ** p_services - return the BTA service mask 1866 ** 1867 ** Returns None 1868 ** 1869 *******************************************************************************/ 1870 BTA_API extern void BTA_GetEirService( UINT8 *p_eir, tBTA_SERVICE_MASK *p_services ); 1871 1872 /******************************************************************************* 1873 ** 1874 ** Function BTA_DmUseSsr 1875 ** 1876 ** Description This function is called to check if the connected peer device 1877 ** supports SSR or not. 1878 ** 1879 ** Returns TRUE, if SSR is supported 1880 ** 1881 *******************************************************************************/ 1882 BTA_API extern BOOLEAN BTA_DmUseSsr( BD_ADDR bd_addr ); 1883 1884 /******************************************************************************* 1885 ** 1886 ** Function BTA_DmGetConnectionState 1887 ** 1888 ** Description Returns whether the remote device is currently connected. 1889 ** 1890 ** Returns 0 if the device is NOT connected. 1891 ** 1892 *******************************************************************************/ 1893 BTA_API extern UINT16 BTA_DmGetConnectionState( BD_ADDR bd_addr ); 1894 1895 1896 /******************************************************************************* 1897 ** 1898 ** Function BTA_DmSetLocalDiRecord 1899 ** 1900 ** Description This function adds a DI record to the local SDP database. 1901 ** 1902 ** Returns BTA_SUCCESS if record set sucessfully, otherwise error code. 1903 ** 1904 *******************************************************************************/ 1905 BTA_API extern tBTA_STATUS BTA_DmSetLocalDiRecord( tBTA_DI_RECORD *p_device_info, 1906 UINT32 *p_handle ); 1907 1908 /******************************************************************************* 1909 ** 1910 ** Function BTA_DmGetLocalDiRecord 1911 ** 1912 ** Description Get a specified DI record to the local SDP database. If no 1913 ** record handle is provided, the primary DI record will be 1914 ** returned. 1915 ** 1916 ** Returns BTA_SUCCESS if record set sucessfully, otherwise error code. 1917 ** 1918 *******************************************************************************/ 1919 BTA_API extern tBTA_STATUS BTA_DmGetLocalDiRecord( tBTA_DI_GET_RECORD *p_device_info, 1920 UINT32 *p_handle ); 1921 1922 /******************************************************************************* 1923 ** 1924 ** Function BTA_DmDiDiscover 1925 ** 1926 ** Description This function queries a remote device for DI information. 1927 ** 1928 ** Returns None. 1929 ** 1930 *******************************************************************************/ 1931 BTA_API extern void BTA_DmDiDiscover( BD_ADDR remote_device, tBTA_DISCOVERY_DB *p_db, 1932 UINT32 len, tBTA_DM_SEARCH_CBACK *p_cback ); 1933 1934 /******************************************************************************* 1935 ** 1936 ** Function BTA_DmGetDiRecord 1937 ** 1938 ** Description This function retrieves a remote device's DI record from 1939 ** the specified database. 1940 ** 1941 ** Returns None. 1942 ** 1943 *******************************************************************************/ 1944 BTA_API extern tBTA_STATUS BTA_DmGetDiRecord( UINT8 get_record_index, tBTA_DI_GET_RECORD *p_device_info, 1945 tBTA_DISCOVERY_DB *p_db ); 1946 1947 /******************************************************************************* 1948 ** 1949 ** 1950 ** Function BTA_DmCloseACL 1951 ** 1952 ** Description This function force to close an ACL connection and remove the 1953 ** device from the security database list of known devices. 1954 ** 1955 ** Parameters: bd_addr - Address of the peer device 1956 ** remove_dev - remove device or not after link down 1957 ** transport - which transport to close 1958 1959 ** 1960 ** Returns void. 1961 ** 1962 *******************************************************************************/ 1963 BTA_API extern void BTA_DmCloseACL(BD_ADDR bd_addr, BOOLEAN remove_dev, tBTA_TRANSPORT transport); 1964 1965 /******************************************************************************* 1966 ** 1967 ** Function BTA_SysFeatures 1968 ** 1969 ** Description This function is called to set system features. 1970 ** 1971 ** Returns void 1972 ** 1973 *******************************************************************************/ 1974 BTA_API extern void BTA_SysFeatures (UINT16 sys_features); 1975 1976 /******************************************************************************* 1977 ** 1978 ** Function bta_dmexecutecallback 1979 ** 1980 ** Description This function will request BTA to execute a call back in the context of BTU task 1981 ** This API was named in lower case because it is only intended 1982 ** for the internal customers(like BTIF). 1983 ** 1984 ** Returns void 1985 ** 1986 *******************************************************************************/ 1987 BTA_API extern void bta_dmexecutecallback (tBTA_DM_EXEC_CBACK* p_callback, void * p_param); 1988 1989 #if (BTM_SCO_HCI_INCLUDED == TRUE) 1990 /******************************************************************************* 1991 ** 1992 ** Function BTA_DmPcmInitSamples 1993 ** 1994 ** Description initialize the down sample converter. 1995 ** 1996 ** src_sps: original samples per second (source audio data) 1997 ** (ex. 44100, 48000) 1998 ** bits: number of bits per pcm sample (16) 1999 ** n_channels: number of channels (i.e. mono(1), stereo(2)...) 2000 ** 2001 ** Returns none 2002 ** 2003 *******************************************************************************/ 2004 BTA_API extern void BTA_DmPcmInitSamples (UINT32 src_sps, UINT32 bits, UINT32 n_channels); 2005 2006 /************************************************************************************** 2007 ** Function BTA_DmPcmResample 2008 ** 2009 ** Description Down sampling utility to convert higher sampling rate into 8K/16bits 2010 ** PCM samples. 2011 ** 2012 ** Parameters p_src: pointer to the buffer where the original sampling PCM 2013 ** are stored. 2014 ** in_bytes: Length of the input PCM sample buffer in byte. 2015 ** p_dst: pointer to the buffer which is to be used to store 2016 ** the converted PCM samples. 2017 ** 2018 ** 2019 ** Returns INT32: number of samples converted. 2020 ** 2021 **************************************************************************************/ 2022 BTA_API extern INT32 BTA_DmPcmResample (void *p_src, UINT32 in_bytes, void *p_dst); 2023 #endif 2024 2025 #if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 2026 /* BLE related API functions */ 2027 /******************************************************************************* 2028 ** 2029 ** Function BTA_DmBleSecurityGrant 2030 ** 2031 ** Description Grant security request access. 2032 ** 2033 ** Parameters: bd_addr - BD address of the peer 2034 ** res - security grant status. 2035 ** 2036 ** Returns void 2037 ** 2038 *******************************************************************************/ 2039 BTA_API extern void BTA_DmBleSecurityGrant(BD_ADDR bd_addr, tBTA_DM_BLE_SEC_GRANT res); 2040 2041 2042 2043 /******************************************************************************* 2044 ** 2045 ** Function BTA_DmBleSetBgConnType 2046 ** 2047 ** Description This function is called to set BLE connectable mode for a 2048 ** peripheral device. 2049 ** 2050 ** Parameters bg_conn_type: it can be auto connection, or selective connection. 2051 ** p_select_cback: callback function when selective connection procedure 2052 ** is being used. 2053 ** 2054 ** Returns void 2055 ** 2056 *******************************************************************************/ 2057 BTA_API extern void BTA_DmBleSetBgConnType(tBTA_DM_BLE_CONN_TYPE bg_conn_type, tBTA_DM_BLE_SEL_CBACK *p_select_cback); 2058 2059 /******************************************************************************* 2060 ** 2061 ** Function BTA_DmBlePasskeyReply 2062 ** 2063 ** Description Send BLE SMP passkey reply. 2064 ** 2065 ** Parameters: bd_addr - BD address of the peer 2066 ** accept - passkey entry sucessful or declined. 2067 ** passkey - passkey value, must be a 6 digit number, 2068 ** can be lead by 0. 2069 ** 2070 ** Returns void 2071 ** 2072 *******************************************************************************/ 2073 BTA_API extern void BTA_DmBlePasskeyReply(BD_ADDR bd_addr, BOOLEAN accept, UINT32 passkey); 2074 2075 /******************************************************************************* 2076 ** 2077 ** Function BTA_DmAddBleDevice 2078 ** 2079 ** Description Add a BLE device. This function will be normally called 2080 ** during host startup to restore all required information 2081 ** for a LE device stored in the NVRAM. 2082 ** 2083 ** Parameters: bd_addr - BD address of the peer 2084 ** dev_type - Remote device's device type. 2085 ** addr_type - LE device address type. 2086 ** 2087 ** Returns void 2088 ** 2089 *******************************************************************************/ 2090 BTA_API extern void BTA_DmAddBleDevice(BD_ADDR bd_addr, tBLE_ADDR_TYPE addr_type, 2091 tBT_DEVICE_TYPE dev_type); 2092 2093 2094 /******************************************************************************* 2095 ** 2096 ** Function BTA_DmAddBleKey 2097 ** 2098 ** Description Add/modify LE device information. This function will be 2099 ** normally called during host startup to restore all required 2100 ** information stored in the NVRAM. 2101 ** 2102 ** Parameters: bd_addr - BD address of the peer 2103 ** p_le_key - LE key values. 2104 ** key_type - LE SMP key type. 2105 ** 2106 ** Returns void 2107 ** 2108 *******************************************************************************/ 2109 BTA_API extern void BTA_DmAddBleKey (BD_ADDR bd_addr, 2110 tBTA_LE_KEY_VALUE *p_le_key, 2111 tBTA_LE_KEY_TYPE key_type); 2112 2113 /******************************************************************************* 2114 ** 2115 ** Function BTA_DmSetBlePrefConnParams 2116 ** 2117 ** Description This function is called to set the preferred connection 2118 ** parameters when default connection parameter is not desired. 2119 ** 2120 ** Parameters: bd_addr - BD address of the peripheral 2121 ** min_conn_int - minimum preferred connection interval 2122 ** max_conn_int - maximum preferred connection interval 2123 ** slave_latency - preferred slave latency 2124 ** supervision_tout - preferred supervision timeout 2125 ** 2126 ** 2127 ** Returns void 2128 ** 2129 *******************************************************************************/ 2130 BTA_API extern void BTA_DmSetBlePrefConnParams(BD_ADDR bd_addr, 2131 UINT16 min_conn_int, UINT16 max_conn_int, 2132 UINT16 slave_latency, UINT16 supervision_tout ); 2133 2134 /******************************************************************************* 2135 ** 2136 ** Function BTA_DmSetBleConnScanParams 2137 ** 2138 ** Description This function is called to set scan parameters used in 2139 ** BLE connection request 2140 ** 2141 ** Parameters: bd_addr - BD address of the peripheral 2142 ** scan_interval - scan interval 2143 ** scan_window - scan window 2144 ** 2145 ** Returns void 2146 ** 2147 *******************************************************************************/ 2148 BTA_API extern void BTA_DmSetBleConnScanParams(UINT16 scan_interval, 2149 UINT16 scan_window ); 2150 2151 /******************************************************************************* 2152 ** 2153 ** Function BTA_DmSetBleAdvParams 2154 ** 2155 ** Description This function sets the advertising parameters BLE functionality. 2156 ** It is to be called when device act in peripheral or broadcaster 2157 ** role. 2158 ** 2159 ** Parameters: adv_int_min - adv interval minimum 2160 ** adv_int_max - adv interval max 2161 ** p_dir_bda - directed adv initator address 2162 ** 2163 ** Returns void 2164 ** 2165 *******************************************************************************/ 2166 BTA_API extern void BTA_DmSetBleAdvParams (UINT16 adv_int_min, UINT16 adv_int_max, 2167 tBLE_BD_ADDR *p_dir_bda); 2168 /******************************************************************************* 2169 ** 2170 ** Function BTA_DmSearchExt 2171 ** 2172 ** Description This function searches for peer Bluetooth devices. It performs 2173 ** an inquiry and gets the remote name for devices. Service 2174 ** discovery is done if services is non zero 2175 ** 2176 ** Parameters p_dm_inq: inquiry conditions 2177 ** services: if service is not empty, service discovery will be done. 2178 ** for all GATT based service condition, put num_uuid, and 2179 ** p_uuid is the pointer to the list of UUID values. 2180 ** p_cback: callback functino when search is completed. 2181 ** 2182 ** 2183 ** 2184 ** Returns void 2185 ** 2186 *******************************************************************************/ 2187 BTA_API extern void BTA_DmSearchExt(tBTA_DM_INQ *p_dm_inq, tBTA_SERVICE_MASK_EXT *p_services, 2188 tBTA_DM_SEARCH_CBACK *p_cback); 2189 2190 /******************************************************************************* 2191 ** 2192 ** Function BTA_DmDiscoverExt 2193 ** 2194 ** Description This function does service discovery for services of a 2195 ** peer device. When services.num_uuid is 0, it indicates all 2196 ** GATT based services are to be searched; other wise a list of 2197 ** UUID of interested services should be provided through 2198 ** services.p_uuid. 2199 ** 2200 ** 2201 ** 2202 ** Returns void 2203 ** 2204 *******************************************************************************/ 2205 BTA_API extern void BTA_DmDiscoverExt(BD_ADDR bd_addr, tBTA_SERVICE_MASK_EXT *p_services, 2206 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search); 2207 2208 /******************************************************************************* 2209 ** 2210 ** Function BTA_DmDiscoverByTransport 2211 ** 2212 ** Description This function does service discovery on particular transport 2213 ** for services of a 2214 ** peer device. When services.num_uuid is 0, it indicates all 2215 ** GATT based services are to be searched; other wise a list of 2216 ** UUID of interested services should be provided through 2217 ** p_services->p_uuid. 2218 ** 2219 ** 2220 ** 2221 ** Returns void 2222 ** 2223 *******************************************************************************/ 2224 BTA_API extern void BTA_DmDiscoverByTransport(BD_ADDR bd_addr, tBTA_SERVICE_MASK_EXT *p_services, 2225 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search, 2226 tBTA_TRANSPORT transport); 2227 2228 /******************************************************************************* 2229 ** 2230 ** Function BTA_DmSetEncryption 2231 ** 2232 ** Description This function is called to ensure that connection is 2233 ** encrypted. Should be called only on an open connection. 2234 ** Typically only needed for connections that first want to 2235 ** bring up unencrypted links, then later encrypt them. 2236 ** 2237 ** Parameters: bd_addr - Address of the peer device 2238 ** transport - transport of the link to be encruypted 2239 ** p_callback - Pointer to callback function to indicat the 2240 ** link encryption status 2241 ** sec_act - This is the security action to indicate 2242 ** what knid of BLE security level is required for 2243 ** the BLE link if the BLE is supported 2244 ** Note: This parameter is ignored for the BR/EDR link 2245 ** or the BLE is not supported 2246 ** 2247 ** Returns void 2248 ** 2249 ** 2250 *******************************************************************************/ 2251 BTA_API extern void BTA_DmSetEncryption(BD_ADDR bd_addr, tBTA_TRANSPORT transport, 2252 tBTA_DM_ENCRYPT_CBACK *p_callback, 2253 tBTA_DM_BLE_SEC_ACT sec_act); 2254 2255 2256 /******************************************************************************* 2257 ** 2258 ** Function BTA_DmBleObserve 2259 ** 2260 ** Description This procedure keep the device listening for advertising 2261 ** events from a broadcast device. 2262 ** 2263 ** Parameters start: start or stop observe. 2264 ** duration : Duration of the scan. Continuous scan if 0 is passed 2265 ** p_results_cb: Callback to be called with scan results 2266 ** 2267 ** Returns void 2268 ** 2269 *******************************************************************************/ 2270 BTA_API extern void BTA_DmBleObserve(BOOLEAN start, UINT8 duration, 2271 tBTA_DM_SEARCH_CBACK *p_results_cb); 2272 2273 2274 #endif 2275 2276 // btla-specific ++ 2277 /******************************************************************************* 2278 ** 2279 ** Function BTA_DmSetAfhChannelAssessment 2280 ** 2281 ** Description This function is called to set the channel assessment mode on or off 2282 ** 2283 ** Returns status 2284 ** 2285 *******************************************************************************/ 2286 BTA_API extern void BTA_DmSetAfhChannelAssessment (BOOLEAN enable_or_disable); 2287 2288 #if BLE_INCLUDED == TRUE 2289 // btla-specific -- 2290 /******************************************************************************* 2291 ** 2292 ** Function BTA_DmBleConfigLocalPrivacy 2293 ** 2294 ** Description Enable/disable privacy on the local device 2295 ** 2296 ** Parameters: privacy_enable - enable/disabe privacy on remote device. 2297 ** 2298 ** Returns void 2299 ** 2300 *******************************************************************************/ 2301 BTA_API extern void BTA_DmBleConfigLocalPrivacy(BOOLEAN privacy_enable); 2302 2303 /******************************************************************************* 2304 ** 2305 ** Function BTA_DmBleEnableRemotePrivacy 2306 ** 2307 ** Description Enable/disable privacy on a remote device 2308 ** 2309 ** Parameters: bd_addr - BD address of the peer 2310 ** privacy_enable - enable/disabe privacy on remote device. 2311 ** 2312 ** Returns void 2313 ** 2314 *******************************************************************************/ 2315 BTA_API extern void BTA_DmBleEnableRemotePrivacy(BD_ADDR bd_addr, BOOLEAN privacy_enable); 2316 2317 2318 /******************************************************************************* 2319 ** 2320 ** Function BTA_DmBleSetAdvConfig 2321 ** 2322 ** Description This function is called to override the BTA default ADV parameters. 2323 ** 2324 ** Parameters Pointer to User defined ADV data structure 2325 ** 2326 ** Returns None 2327 ** 2328 *******************************************************************************/ 2329 BTA_API extern void BTA_DmBleSetAdvConfig (tBTA_BLE_AD_MASK data_mask, 2330 tBTA_BLE_ADV_DATA *p_adv_cfg, 2331 tBTA_SET_ADV_DATA_CMPL_CBACK *p_adv_data_cback); 2332 2333 /******************************************************************************* 2334 ** 2335 ** Function BTA_DmBleSetScanRsp 2336 ** 2337 ** Description This function is called to override the BTA scan response. 2338 ** 2339 ** Parameters Pointer to User defined ADV data structure 2340 ** 2341 ** Returns None 2342 ** 2343 *******************************************************************************/ 2344 BTA_API extern void BTA_DmBleSetScanRsp (tBTA_BLE_AD_MASK data_mask, 2345 tBTA_BLE_ADV_DATA *p_adv_cfg, 2346 tBTA_SET_ADV_DATA_CMPL_CBACK *p_adv_data_cback); 2347 2348 /******************************************************************************* 2349 ** 2350 ** Function BTA_DmBleBroadcast 2351 ** 2352 ** Description This function starts or stops LE broadcasting. 2353 ** 2354 ** Parameters start: start or stop broadcast. 2355 ** 2356 ** Returns None 2357 ** 2358 *******************************************************************************/ 2359 BTA_API extern void BTA_DmBleBroadcast (BOOLEAN start); 2360 2361 2362 /******************************************************************************* 2363 ** 2364 ** Function BTA_BleEnableAdvInstance 2365 ** 2366 ** Description This function enables the Multi ADV instance feature 2367 ** 2368 ** Parameters p_params Pointer to ADV param user defined structure 2369 ** p_cback Pointer to Multi ADV callback structure 2370 ** p_ref - Reference pointer 2371 ** 2372 ** Returns None 2373 ** 2374 *******************************************************************************/ 2375 BTA_API extern void BTA_BleEnableAdvInstance (tBTA_BLE_ADV_PARAMS *p_params, 2376 tBTA_BLE_MULTI_ADV_CBACK *p_cback,void *p_ref); 2377 2378 /******************************************************************************* 2379 ** 2380 ** Function BTA_BleUpdateAdvInstParam 2381 ** 2382 ** Description This function updates the Multi ADV instance params 2383 ** 2384 ** Parameters inst_id Instance ID 2385 ** p_params Pointer to ADV param user defined structure 2386 ** 2387 ** Returns None 2388 ** 2389 *******************************************************************************/ 2390 BTA_API extern void BTA_BleUpdateAdvInstParam (UINT8 inst_id, 2391 tBTA_BLE_ADV_PARAMS *p_params); 2392 2393 /******************************************************************************* 2394 ** 2395 ** Function BTA_BleCfgAdvInstData 2396 ** 2397 ** Description This function is called to configure the ADV instance data 2398 ** 2399 ** Parameters inst_id - Instance ID 2400 ** is_scan_rsp - Boolean value Scan response 2401 ** Pointer to User defined ADV data structure 2402 ** Returns None 2403 ** 2404 *******************************************************************************/ 2405 BTA_API extern void BTA_BleCfgAdvInstData (UINT8 inst_id, BOOLEAN is_scan_rsp, 2406 tBTA_BLE_AD_MASK data_mask, tBTA_BLE_ADV_DATA *p_data); 2407 2408 /******************************************************************************* 2409 ** 2410 ** Function BTA_BleDisableAdvInstance 2411 ** 2412 ** Description This function is called to disable the ADV instance 2413 ** 2414 ** Parameters inst_id - Instance ID to be disabled 2415 ** 2416 ** Returns None 2417 ** 2418 *******************************************************************************/ 2419 BTA_API extern void BTA_BleDisableAdvInstance(UINT8 inst_id); 2420 2421 /******************************************************************************* 2422 ** 2423 ** Function BTA_DmBleUpdateConnectionParams 2424 ** 2425 ** Description Update connection parameters, can only be used when connection is up. 2426 ** 2427 ** Parameters: bd_addr - BD address of the peer 2428 ** min_int - minimum connection interval, [0x0004~ 0x4000] 2429 ** max_int - maximum connection interval, [0x0004~ 0x4000] 2430 ** latency - slave latency [0 ~ 500] 2431 ** timeout - supervision timeout [0x000a ~ 0xc80] 2432 ** 2433 ** Returns void 2434 ** 2435 *******************************************************************************/ 2436 BTA_API extern void BTA_DmBleUpdateConnectionParams(BD_ADDR bd_addr, UINT16 min_int, 2437 UINT16 max_int, UINT16 latency, UINT16 timeout); 2438 2439 /******************************************************************************* 2440 ** 2441 ** Function BTA_DmBleSetStorageParams 2442 ** 2443 ** Description This function is called to set the storage parameters 2444 ** 2445 ** Parameters batch_scan_full_max -Max storage space (in %) allocated to full scanning 2446 ** batch_scan_trunc_max -Max storage space (in %) allocated to truncated scanning 2447 ** batch_scan_notify_threshold - Setup notification level based on total space 2448 ** consumed by both pools. Setting it to 0 will disable threshold notification 2449 ** p_setup_cback - Setup callback 2450 ** p_thres_cback - Threshold callback 2451 ** p_rep_cback - Reports callback 2452 ** ref_value - Reference value 2453 ** 2454 ** Returns None 2455 ** 2456 *******************************************************************************/ 2457 BTA_API extern void BTA_DmBleSetStorageParams(UINT8 batch_scan_full_max, 2458 UINT8 batch_scan_trunc_max, 2459 UINT8 batch_scan_notify_threshold, 2460 tBTA_BLE_SCAN_SETUP_CBACK *p_setup_cback, 2461 tBTA_BLE_SCAN_THRESHOLD_CBACK *p_thres_cback, 2462 tBTA_BLE_SCAN_REP_CBACK* p_rep_cback, 2463 tBTA_DM_BLE_REF_VALUE ref_value); 2464 2465 /******************************************************************************* 2466 ** 2467 ** Function BTA_DmBleEnableBatchScan 2468 ** 2469 ** Description This function is called to enable the batch scan 2470 ** 2471 ** Parameters scan_mode -Batch scan mode 2472 ** scan_interval - Scan interval 2473 ** scan_window - Scan window 2474 ** discard_rule -Discard rules 2475 ** addr_type - Address type 2476 ** ref_value - Reference value 2477 ** 2478 ** Returns None 2479 ** 2480 *******************************************************************************/ 2481 BTA_API extern void BTA_DmBleEnableBatchScan(tBTA_BLE_SCAN_MODE scan_mode, 2482 UINT32 scan_interval, UINT32 scan_window, 2483 tBTA_BLE_DISCARD_RULE discard_rule, 2484 tBLE_ADDR_TYPE addr_type, 2485 tBTA_DM_BLE_REF_VALUE ref_value); 2486 2487 /******************************************************************************* 2488 ** 2489 ** Function BTA_DmBleReadScanReports 2490 ** 2491 ** Description This function is called to read the batch scan reports 2492 ** 2493 ** Parameters scan_mode -Batch scan mode 2494 ** ref_value - Reference value 2495 ** 2496 ** Returns None 2497 ** 2498 *******************************************************************************/ 2499 BTA_API extern void BTA_DmBleReadScanReports(tBTA_BLE_SCAN_MODE scan_type, 2500 tBTA_DM_BLE_REF_VALUE ref_value); 2501 2502 /******************************************************************************* 2503 ** 2504 ** Function BTA_DmBleDisableBatchScan 2505 ** 2506 ** Description This function is called to disable the batch scanning 2507 ** 2508 ** Parameters ref_value - Reference value 2509 ** 2510 ** Returns None 2511 ** 2512 *******************************************************************************/ 2513 BTA_API extern void BTA_DmBleDisableBatchScan(tBTA_DM_BLE_REF_VALUE ref_value); 2514 2515 /******************************************************************************* 2516 ** 2517 ** Function BTA_DmEnableScanFilter 2518 ** 2519 ** Description This function is called to enable the adv data payload filter 2520 ** 2521 ** Parameters action - enable or disable the APCF feature 2522 ** p_cmpl_cback - Command completed callback 2523 ** ref_value - Reference value 2524 ** 2525 ** Returns void 2526 ** 2527 *******************************************************************************/ 2528 BTA_API extern void BTA_DmEnableScanFilter(UINT8 action, 2529 tBTA_DM_BLE_PF_STATUS_CBACK *p_cmpl_cback, 2530 tBTA_DM_BLE_REF_VALUE ref_value); 2531 2532 /******************************************************************************* 2533 ** 2534 ** Function BTA_DmBleScanFilterSetup 2535 ** 2536 ** Description This function is called to setup the filter params 2537 ** 2538 ** Parameters p_target: enable the filter condition on a target device; if NULL 2539 ** filt_index - Filter index 2540 ** p_filt_params -Filter parameters 2541 ** ref_value - Reference value 2542 ** action - Add, delete or clear 2543 ** p_cmpl_back - Command completed callback 2544 ** 2545 ** Returns void 2546 ** 2547 *******************************************************************************/ 2548 BTA_API extern void BTA_DmBleScanFilterSetup(UINT8 action, 2549 tBTA_DM_BLE_PF_FILT_INDEX filt_index, 2550 tBTA_DM_BLE_PF_FILT_PARAMS *p_filt_params, 2551 tBLE_BD_ADDR *p_target, 2552 tBTA_DM_BLE_PF_PARAM_CBACK *p_cmpl_cback, 2553 tBTA_DM_BLE_REF_VALUE ref_value); 2554 2555 /******************************************************************************* 2556 ** 2557 ** Function BTA_DmBleCfgFilterCondition 2558 ** 2559 ** Description This function is called to configure the adv data payload filter 2560 ** condition. 2561 ** 2562 ** Parameters action: to read/write/clear 2563 ** cond_type: filter condition type 2564 ** filt_index - Filter index 2565 ** p_cond: filter condition parameter 2566 ** p_cmpl_back - Command completed callback 2567 ** ref_value - Reference value 2568 ** 2569 ** Returns void 2570 ** 2571 *******************************************************************************/ 2572 BTA_API extern void BTA_DmBleCfgFilterCondition(tBTA_DM_BLE_SCAN_COND_OP action, 2573 tBTA_DM_BLE_PF_COND_TYPE cond_type, 2574 tBTA_DM_BLE_PF_FILT_INDEX filt_index, 2575 tBTA_DM_BLE_PF_COND_PARAM *p_cond, 2576 tBTA_DM_BLE_PF_CFG_CBACK *p_cmpl_cback, 2577 tBTA_DM_BLE_REF_VALUE ref_value); 2578 2579 2580 /******************************************************************************* 2581 ** 2582 ** Function BTA_DmBleTrackAdvertiser 2583 ** 2584 ** Description This function is called to track the advertiser 2585 ** 2586 ** Parameters ref_value - Reference value 2587 ** p_track_adv_cback - ADV callback 2588 ** 2589 ** Returns None 2590 ** 2591 *******************************************************************************/ 2592 BTA_API extern void BTA_DmBleTrackAdvertiser(tBTA_DM_BLE_REF_VALUE ref_value, 2593 tBTA_BLE_TRACK_ADV_CBACK *p_track_adv_cback); 2594 2595 /******************************************************************************* 2596 ** 2597 ** Function BTA_DmBleGetEnergyInfo 2598 ** 2599 ** Description This function is called to obtain the energy info 2600 ** 2601 ** Parameters p_cmpl_cback - Command complete callback 2602 ** 2603 ** Returns void 2604 ** 2605 *******************************************************************************/ 2606 BTA_API extern void BTA_DmBleGetEnergyInfo(tBTA_BLE_ENERGY_INFO_CBACK *p_cmpl_cback); 2607 2608 /******************************************************************************* 2609 ** 2610 ** Function BTA_BrcmInit 2611 ** 2612 ** Description This function initializes Broadcom specific VS handler in BTA 2613 ** 2614 ** Returns void 2615 ** 2616 *******************************************************************************/ 2617 BTA_API extern void BTA_VendorInit (void); 2618 2619 /******************************************************************************* 2620 ** 2621 ** Function BTA_BrcmCleanup 2622 ** 2623 ** Description This function frees up Broadcom specific VS specific dynamic memory 2624 ** 2625 ** Returns void 2626 ** 2627 *******************************************************************************/ 2628 BTA_API extern void BTA_VendorCleanup (void); 2629 2630 #endif 2631 2632 #ifdef __cplusplus 2633 } 2634 #endif 2635 2636 #endif /* BTA_API_H */ 2637 2638