1 /****************************************************************************** 2 * 3 * Copyright (C) 1999-2012 Broadcom Corporation 4 * 5 * Licensed under the Apache License, Version 2.0 (the "License"); 6 * you may not use this file except in compliance with the License. 7 * You may obtain a copy of the License at: 8 * 9 * http://www.apache.org/licenses/LICENSE-2.0 10 * 11 * Unless required by applicable law or agreed to in writing, software 12 * distributed under the License is distributed on an "AS IS" BASIS, 13 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. 14 * See the License for the specific language governing permissions and 15 * limitations under the License. 16 * 17 ******************************************************************************/ 18 19 #ifndef BT_TYPES_H 20 #define BT_TYPES_H 21 22 #include "data_types.h" 23 24 #ifdef _WIN32 25 #ifdef BLUESTACK_TESTER 26 #include "bte_stack_entry.h" 27 #endif 28 #endif 29 30 /* READ WELL !! 31 ** 32 ** This section defines global events. These are events that cross layers. 33 ** Any event that passes between layers MUST be one of these events. Tasks 34 ** can use their own events internally, but a FUNDAMENTAL design issue is 35 ** that global events MUST be one of these events defined below. 36 ** 37 ** The convention used is the the event name contains the layer that the 38 ** event is going to. 39 */ 40 #define BT_EVT_MASK 0xFF00 41 #define BT_SUB_EVT_MASK 0x00FF 42 /* To Bluetooth Upper Layers */ 43 /************************************/ 44 #define BT_EVT_TO_BTU_L2C_EVT 0x0900 /* L2CAP event */ 45 #define BT_EVT_TO_BTU_HCI_EVT 0x1000 /* HCI Event */ 46 #define BT_EVT_TO_BTU_HCI_BR_EDR_EVT (0x0000 | BT_EVT_TO_BTU_HCI_EVT) /* event from BR/EDR controller */ 47 #define BT_EVT_TO_BTU_HCI_AMP1_EVT (0x0001 | BT_EVT_TO_BTU_HCI_EVT) /* event from local AMP 1 controller */ 48 #define BT_EVT_TO_BTU_HCI_AMP2_EVT (0x0002 | BT_EVT_TO_BTU_HCI_EVT) /* event from local AMP 2 controller */ 49 #define BT_EVT_TO_BTU_HCI_AMP3_EVT (0x0003 | BT_EVT_TO_BTU_HCI_EVT) /* event from local AMP 3 controller */ 50 51 #define BT_EVT_TO_BTU_HCI_ACL 0x1100 /* ACL Data from HCI */ 52 #define BT_EVT_TO_BTU_HCI_SCO 0x1200 /* SCO Data from HCI */ 53 #define BT_EVT_TO_BTU_HCIT_ERR 0x1300 /* HCI Transport Error */ 54 55 #define BT_EVT_TO_BTU_SP_EVT 0x1400 /* Serial Port Event */ 56 #define BT_EVT_TO_BTU_SP_DATA 0x1500 /* Serial Port Data */ 57 58 #define BT_EVT_TO_BTU_HCI_CMD 0x1600 /* HCI command from upper layer */ 59 60 61 #define BT_EVT_TO_BTU_L2C_SEG_XMIT 0x1900 /* L2CAP segment(s) transmitted */ 62 63 #define BT_EVT_PROXY_INCOMING_MSG 0x1A00 /* BlueStackTester event: incoming message from target */ 64 65 #define BT_EVT_BTSIM 0x1B00 /* Insight BTSIM event */ 66 #define BT_EVT_BTISE 0x1C00 /* Insight Script Engine event */ 67 68 /* To LM */ 69 /************************************/ 70 #define BT_EVT_TO_LM_HCI_CMD 0x2000 /* HCI Command */ 71 #define BT_EVT_TO_LM_HCI_ACL 0x2100 /* HCI ACL Data */ 72 #define BT_EVT_TO_LM_HCI_SCO 0x2200 /* HCI SCO Data */ 73 #define BT_EVT_TO_LM_HCIT_ERR 0x2300 /* HCI Transport Error */ 74 #define BT_EVT_TO_LM_LC_EVT 0x2400 /* LC event */ 75 #define BT_EVT_TO_LM_LC_LMP 0x2500 /* LC Received LMP command frame */ 76 #define BT_EVT_TO_LM_LC_ACL 0x2600 /* LC Received ACL data */ 77 #define BT_EVT_TO_LM_LC_SCO 0x2700 /* LC Received SCO data (not used) */ 78 #define BT_EVT_TO_LM_LC_ACL_TX 0x2800 /* LMP data transmit complete */ 79 #define BT_EVT_TO_LM_LC_LMPC_TX 0x2900 /* LMP Command transmit complete */ 80 #define BT_EVT_TO_LM_LOCAL_ACL_LB 0x2a00 /* Data to be locally loopbacked */ 81 #define BT_EVT_TO_LM_HCI_ACL_ACK 0x2b00 /* HCI ACL Data ack (not used) */ 82 #define BT_EVT_TO_LM_DIAG 0x2c00 /* LM Diagnostics commands */ 83 84 85 #define BT_EVT_TO_BTM_CMDS 0x2f00 86 #define BT_EVT_TO_BTM_PM_MDCHG_EVT (0x0001 | BT_EVT_TO_BTM_CMDS) 87 88 #define BT_EVT_TO_TCS_CMDS 0x3000 89 90 #define BT_EVT_TO_OBX_CL_MSG 0x3100 91 #define BT_EVT_TO_OBX_SR_MSG 0x3200 92 93 #define BT_EVT_TO_CTP_CMDS 0x3300 94 95 /* Obex Over L2CAP */ 96 #define BT_EVT_TO_OBX_CL_L2C_MSG 0x3400 97 #define BT_EVT_TO_OBX_SR_L2C_MSG 0x3500 98 99 /* ftp events */ 100 #define BT_EVT_TO_FTP_SRVR_CMDS 0x3600 101 #define BT_EVT_TO_FTP_CLNT_CMDS 0x3700 102 103 #define BT_EVT_TO_BTU_SAP 0x3800 /* SIM Access Profile events */ 104 105 /* opp events */ 106 #define BT_EVT_TO_OPP_SRVR_CMDS 0x3900 107 #define BT_EVT_TO_OPP_CLNT_CMDS 0x3a00 108 109 /* gap events */ 110 #define BT_EVT_TO_GAP_MSG 0x3b00 111 112 /* start timer */ 113 #define BT_EVT_TO_START_TIMER 0x3c00 114 115 /* stop timer */ 116 #define BT_EVT_TO_STOP_TIMER 0x3d00 117 118 /* start quick timer */ 119 #define BT_EVT_TO_START_QUICK_TIMER 0x3e00 120 121 122 /* for NFC */ 123 /************************************/ 124 #define BT_EVT_TO_NFC_NCI 0x4000 /* NCI Command, Notification or Data*/ 125 #define BT_EVT_TO_NFC_INIT 0x4100 /* Initialization message */ 126 #define BT_EVT_TO_NCI_LP 0x4200 /* Low power */ 127 #define BT_EVT_TO_NFC_ERR 0x4300 /* Error notification to NFC Task */ 128 129 #define BT_EVT_TO_NFCCSIM_NCI 0x4a00 /* events to NFCC simulation (NCI packets) */ 130 131 /* start timer */ 132 #define BT_EVT_TO_START_TIMER_ONESHOT 0x4c00 133 134 /* stop timer */ 135 #define BT_EVT_TO_STOP_TIMER_ONESHOT 0x4d00 136 137 /* HCISU Events */ 138 139 #define BT_EVT_HCISU 0x5000 140 141 // btla-specific ++ 142 #define BT_EVT_TO_HCISU_RECONFIG_EVT (0x0001 | BT_EVT_HCISU) 143 #define BT_EVT_TO_HCISU_UPDATE_BAUDRATE_EVT (0x0002 | BT_EVT_HCISU) 144 #define BT_EVT_TO_HCISU_LP_ENABLE_EVT (0x0003 | BT_EVT_HCISU) 145 #define BT_EVT_TO_HCISU_LP_DISABLE_EVT (0x0004 | BT_EVT_HCISU) 146 // btla-specific -- 147 #define BT_EVT_TO_HCISU_LP_APP_SLEEPING_EVT (0x0005 | BT_EVT_HCISU) 148 #define BT_EVT_TO_HCISU_LP_ALLOW_BT_SLEEP_EVT (0x0006 | BT_EVT_HCISU) 149 #define BT_EVT_TO_HCISU_LP_WAKEUP_HOST_EVT (0x0007 | BT_EVT_HCISU) 150 #define BT_EVT_TO_HCISU_LP_RCV_H4IBSS_EVT (0x0008 | BT_EVT_HCISU) 151 #define BT_EVT_TO_HCISU_H5_RESET_EVT (0x0009 | BT_EVT_HCISU) 152 #define BT_EVT_HCISU_START_QUICK_TIMER (0x000a | BT_EVT_HCISU) 153 154 #define BT_EVT_DATA_TO_AMP_1 0x5100 155 #define BT_EVT_DATA_TO_AMP_15 0x5f00 156 157 /* HSP Events */ 158 159 #define BT_EVT_BTU_HSP2 0x6000 160 161 #define BT_EVT_TO_BTU_HSP2_EVT (0x0001 | BT_EVT_BTU_HSP2) 162 163 /* BPP Events */ 164 #define BT_EVT_TO_BPP_PR_CMDS 0x6100 /* Printer Events */ 165 #define BT_EVT_TO_BPP_SND_CMDS 0x6200 /* BPP Sender Events */ 166 167 /* BIP Events */ 168 #define BT_EVT_TO_BIP_CMDS 0x6300 169 170 /* HCRP Events */ 171 172 #define BT_EVT_BTU_HCRP 0x7000 173 174 #define BT_EVT_TO_BTU_HCRP_EVT (0x0001 | BT_EVT_BTU_HCRP) 175 #define BT_EVT_TO_BTU_HCRPM_EVT (0x0002 | BT_EVT_BTU_HCRP) 176 177 178 #define BT_EVT_BTU_HFP 0x8000 179 #define BT_EVT_TO_BTU_HFP_EVT (0x0001 | BT_EVT_BTU_HFP) 180 181 #define BT_EVT_BTU_IPC_EVT 0x9000 182 #define BT_EVT_BTU_IPC_LOGMSG_EVT (0x0000 | BT_EVT_BTU_IPC_EVT) 183 #define BT_EVT_BTU_IPC_ACL_EVT (0x0001 | BT_EVT_BTU_IPC_EVT) 184 #define BT_EVT_BTU_IPC_BTU_EVT (0x0002 | BT_EVT_BTU_IPC_EVT) 185 #define BT_EVT_BTU_IPC_L2C_EVT (0x0003 | BT_EVT_BTU_IPC_EVT) 186 #define BT_EVT_BTU_IPC_L2C_MSG_EVT (0x0004 | BT_EVT_BTU_IPC_EVT) 187 #define BT_EVT_BTU_IPC_BTM_EVT (0x0005 | BT_EVT_BTU_IPC_EVT) 188 #define BT_EVT_BTU_IPC_AVDT_EVT (0x0006 | BT_EVT_BTU_IPC_EVT) 189 #define BT_EVT_BTU_IPC_SLIP_EVT (0x0007 | BT_EVT_BTU_IPC_EVT) 190 #define BT_EVT_BTU_IPC_MGMT_EVT (0x0008 | BT_EVT_BTU_IPC_EVT) 191 #define BT_EVT_BTU_IPC_BTTRC_EVT (0x0009 | BT_EVT_BTU_IPC_EVT) 192 #define BT_EVT_BTU_IPC_BURST_EVT (0x000A | BT_EVT_BTU_IPC_EVT) 193 194 195 /* BTIF Events */ 196 #define BT_EVT_BTIF 0xA000 197 #define BT_EVT_CONTEXT_SWITCH_EVT (0x0001 | BT_EVT_BTIF) 198 199 #define BT_EVT_TRIGGER_STACK_INIT EVENT_MASK(APPL_EVT_0) 200 #define BT_EVT_HARDWARE_INIT_FAIL EVENT_MASK(APPL_EVT_1) 201 202 #define BT_EVT_PRELOAD_CMPL EVENT_MASK(APPL_EVT_6) 203 204 /* Define the header of each buffer used in the Bluetooth stack. 205 */ 206 typedef struct 207 { 208 uint16_t event; 209 uint16_t len; 210 uint16_t offset; 211 uint16_t layer_specific; 212 uint8_t data[]; 213 } BT_HDR; 214 215 #define BT_HDR_SIZE (sizeof (BT_HDR)) 216 217 #define BT_PSM_SDP 0x0001 218 #define BT_PSM_RFCOMM 0x0003 219 #define BT_PSM_TCS 0x0005 220 #define BT_PSM_CTP 0x0007 221 #define BT_PSM_BNEP 0x000F 222 #define BT_PSM_HIDC 0x0011 223 #define BT_PSM_HIDI 0x0013 224 #define BT_PSM_UPNP 0x0015 225 #define BT_PSM_AVCTP 0x0017 226 #define BT_PSM_AVDTP 0x0019 227 #define BT_PSM_AVCTP_13 0x001B /* Advanced Control - Browsing */ 228 #define BT_PSM_UDI_CP 0x001D /* Unrestricted Digital Information Profile C-Plane */ 229 #define BT_PSM_ATT 0x001F /* Attribute Protocol */ 230 231 232 /* These macros extract the HCI opcodes from a buffer 233 */ 234 #define HCI_GET_CMD_HDR_OPCODE(p) (UINT16)((*((UINT8 *)((p) + 1) + p->offset) + \ 235 (*((UINT8 *)((p) + 1) + p->offset + 1) << 8))) 236 #define HCI_GET_CMD_HDR_PARAM_LEN(p) (UINT8) (*((UINT8 *)((p) + 1) + p->offset + 2)) 237 238 #define HCI_GET_EVT_HDR_OPCODE(p) (UINT8)(*((UINT8 *)((p) + 1) + p->offset)) 239 #define HCI_GET_EVT_HDR_PARAM_LEN(p) (UINT8) (*((UINT8 *)((p) + 1) + p->offset + 1)) 240 241 242 /******************************************************************************** 243 ** Macros to get and put bytes to and from a stream (Little Endian format). 244 */ 245 #define UINT32_TO_STREAM(p, u32) {*(p)++ = (UINT8)(u32); *(p)++ = (UINT8)((u32) >> 8); *(p)++ = (UINT8)((u32) >> 16); *(p)++ = (UINT8)((u32) >> 24);} 246 #define UINT24_TO_STREAM(p, u24) {*(p)++ = (UINT8)(u24); *(p)++ = (UINT8)((u24) >> 8); *(p)++ = (UINT8)((u24) >> 16);} 247 #define UINT16_TO_STREAM(p, u16) {*(p)++ = (UINT8)(u16); *(p)++ = (UINT8)((u16) >> 8);} 248 #define UINT8_TO_STREAM(p, u8) {*(p)++ = (UINT8)(u8);} 249 #define INT8_TO_STREAM(p, u8) {*(p)++ = (INT8)(u8);} 250 #define ARRAY32_TO_STREAM(p, a) {register int ijk; for (ijk = 0; ijk < 32; ijk++) *(p)++ = (UINT8) a[31 - ijk];} 251 #define ARRAY16_TO_STREAM(p, a) {register int ijk; for (ijk = 0; ijk < 16; ijk++) *(p)++ = (UINT8) a[15 - ijk];} 252 #define ARRAY8_TO_STREAM(p, a) {register int ijk; for (ijk = 0; ijk < 8; ijk++) *(p)++ = (UINT8) a[7 - ijk];} 253 #define BDADDR_TO_STREAM(p, a) {register int ijk; for (ijk = 0; ijk < BD_ADDR_LEN; ijk++) *(p)++ = (UINT8) a[BD_ADDR_LEN - 1 - ijk];} 254 #define LAP_TO_STREAM(p, a) {register int ijk; for (ijk = 0; ijk < LAP_LEN; ijk++) *(p)++ = (UINT8) a[LAP_LEN - 1 - ijk];} 255 #define DEVCLASS_TO_STREAM(p, a) {register int ijk; for (ijk = 0; ijk < DEV_CLASS_LEN;ijk++) *(p)++ = (UINT8) a[DEV_CLASS_LEN - 1 - ijk];} 256 #define ARRAY_TO_STREAM(p, a, len) {register int ijk; for (ijk = 0; ijk < len; ijk++) *(p)++ = (UINT8) a[ijk];} 257 #define REVERSE_ARRAY_TO_STREAM(p, a, len) {register int ijk; for (ijk = 0; ijk < len; ijk++) *(p)++ = (UINT8) a[len - 1 - ijk];} 258 259 #define STREAM_TO_UINT8(u8, p) {u8 = (UINT8)(*(p)); (p) += 1;} 260 #define STREAM_TO_UINT16(u16, p) {u16 = ((UINT16)(*(p)) + (((UINT16)(*((p) + 1))) << 8)); (p) += 2;} 261 #define STREAM_TO_UINT24(u32, p) {u32 = (((UINT32)(*(p))) + ((((UINT32)(*((p) + 1)))) << 8) + ((((UINT32)(*((p) + 2)))) << 16) ); (p) += 3;} 262 #define STREAM_TO_UINT32(u32, p) {u32 = (((UINT32)(*(p))) + ((((UINT32)(*((p) + 1)))) << 8) + ((((UINT32)(*((p) + 2)))) << 16) + ((((UINT32)(*((p) + 3)))) << 24)); (p) += 4;} 263 #define STREAM_TO_BDADDR(a, p) {register int ijk; register UINT8 *pbda = (UINT8 *)a + BD_ADDR_LEN - 1; for (ijk = 0; ijk < BD_ADDR_LEN; ijk++) *pbda-- = *p++;} 264 #define STREAM_TO_ARRAY32(a, p) {register int ijk; register UINT8 *_pa = (UINT8 *)a + 31; for (ijk = 0; ijk < 32; ijk++) *_pa-- = *p++;} 265 #define STREAM_TO_ARRAY16(a, p) {register int ijk; register UINT8 *_pa = (UINT8 *)a + 15; for (ijk = 0; ijk < 16; ijk++) *_pa-- = *p++;} 266 #define STREAM_TO_ARRAY8(a, p) {register int ijk; register UINT8 *_pa = (UINT8 *)a + 7; for (ijk = 0; ijk < 8; ijk++) *_pa-- = *p++;} 267 #define STREAM_TO_DEVCLASS(a, p) {register int ijk; register UINT8 *_pa = (UINT8 *)a + DEV_CLASS_LEN - 1; for (ijk = 0; ijk < DEV_CLASS_LEN; ijk++) *_pa-- = *p++;} 268 #define STREAM_TO_LAP(a, p) {register int ijk; register UINT8 *plap = (UINT8 *)a + LAP_LEN - 1; for (ijk = 0; ijk < LAP_LEN; ijk++) *plap-- = *p++;} 269 #define STREAM_TO_ARRAY(a, p, len) {register int ijk; for (ijk = 0; ijk < len; ijk++) ((UINT8 *) a)[ijk] = *p++;} 270 #define REVERSE_STREAM_TO_ARRAY(a, p, len) {register int ijk; register UINT8 *_pa = (UINT8 *)a + len - 1; for (ijk = 0; ijk < len; ijk++) *_pa-- = *p++;} 271 272 /******************************************************************************** 273 ** Macros to get and put bytes to and from a field (Little Endian format). 274 ** These are the same as to stream, except the pointer is not incremented. 275 */ 276 #define UINT32_TO_FIELD(p, u32) {*(UINT8 *)(p) = (UINT8)(u32); *((UINT8 *)(p)+1) = (UINT8)((u32) >> 8); *((UINT8 *)(p)+2) = (UINT8)((u32) >> 16); *((UINT8 *)(p)+3) = (UINT8)((u32) >> 24);} 277 #define UINT24_TO_FIELD(p, u24) {*(UINT8 *)(p) = (UINT8)(u24); *((UINT8 *)(p)+1) = (UINT8)((u24) >> 8); *((UINT8 *)(p)+2) = (UINT8)((u24) >> 16);} 278 #define UINT16_TO_FIELD(p, u16) {*(UINT8 *)(p) = (UINT8)(u16); *((UINT8 *)(p)+1) = (UINT8)((u16) >> 8);} 279 #define UINT8_TO_FIELD(p, u8) {*(UINT8 *)(p) = (UINT8)(u8);} 280 281 282 /******************************************************************************** 283 ** Macros to get and put bytes to and from a stream (Big Endian format) 284 */ 285 #define UINT32_TO_BE_STREAM(p, u32) {*(p)++ = (UINT8)((u32) >> 24); *(p)++ = (UINT8)((u32) >> 16); *(p)++ = (UINT8)((u32) >> 8); *(p)++ = (UINT8)(u32); } 286 #define UINT24_TO_BE_STREAM(p, u24) {*(p)++ = (UINT8)((u24) >> 16); *(p)++ = (UINT8)((u24) >> 8); *(p)++ = (UINT8)(u24);} 287 #define UINT16_TO_BE_STREAM(p, u16) {*(p)++ = (UINT8)((u16) >> 8); *(p)++ = (UINT8)(u16);} 288 #define UINT8_TO_BE_STREAM(p, u8) {*(p)++ = (UINT8)(u8);} 289 #define ARRAY_TO_BE_STREAM(p, a, len) {register int ijk; for (ijk = 0; ijk < len; ijk++) *(p)++ = (UINT8) a[ijk];} 290 291 #define BE_STREAM_TO_UINT8(u8, p) {u8 = (UINT8)(*(p)); (p) += 1;} 292 #define BE_STREAM_TO_UINT16(u16, p) {u16 = (UINT16)(((UINT16)(*(p)) << 8) + (UINT16)(*((p) + 1))); (p) += 2;} 293 #define BE_STREAM_TO_UINT24(u32, p) {u32 = (((UINT32)(*((p) + 2))) + ((UINT32)(*((p) + 1)) << 8) + ((UINT32)(*(p)) << 16)); (p) += 3;} 294 #define BE_STREAM_TO_UINT32(u32, p) {u32 = ((UINT32)(*((p) + 3)) + ((UINT32)(*((p) + 2)) << 8) + ((UINT32)(*((p) + 1)) << 16) + ((UINT32)(*(p)) << 24)); (p) += 4;} 295 #define BE_STREAM_TO_ARRAY(p, a, len) {register int ijk; for (ijk = 0; ijk < len; ijk++) ((UINT8 *) a)[ijk] = *p++;} 296 297 298 /******************************************************************************** 299 ** Macros to get and put bytes to and from a field (Big Endian format). 300 ** These are the same as to stream, except the pointer is not incremented. 301 */ 302 #define UINT32_TO_BE_FIELD(p, u32) {*(UINT8 *)(p) = (UINT8)((u32) >> 24); *((UINT8 *)(p)+1) = (UINT8)((u32) >> 16); *((UINT8 *)(p)+2) = (UINT8)((u32) >> 8); *((UINT8 *)(p)+3) = (UINT8)(u32); } 303 #define UINT24_TO_BE_FIELD(p, u24) {*(UINT8 *)(p) = (UINT8)((u24) >> 16); *((UINT8 *)(p)+1) = (UINT8)((u24) >> 8); *((UINT8 *)(p)+2) = (UINT8)(u24);} 304 #define UINT16_TO_BE_FIELD(p, u16) {*(UINT8 *)(p) = (UINT8)((u16) >> 8); *((UINT8 *)(p)+1) = (UINT8)(u16);} 305 #define UINT8_TO_BE_FIELD(p, u8) {*(UINT8 *)(p) = (UINT8)(u8);} 306 307 308 /* Common Bluetooth field definitions */ 309 #define BD_ADDR_LEN 6 /* Device address length */ 310 typedef UINT8 BD_ADDR[BD_ADDR_LEN]; /* Device address */ 311 typedef UINT8 *BD_ADDR_PTR; /* Pointer to Device Address */ 312 313 #define AMP_KEY_TYPE_GAMP 0 314 #define AMP_KEY_TYPE_WIFI 1 315 #define AMP_KEY_TYPE_UWB 2 316 typedef UINT8 tAMP_KEY_TYPE; 317 318 #define BT_OCTET8_LEN 8 319 typedef UINT8 BT_OCTET8[BT_OCTET8_LEN]; /* octet array: size 16 */ 320 321 #define LINK_KEY_LEN 16 322 typedef UINT8 LINK_KEY[LINK_KEY_LEN]; /* Link Key */ 323 324 #define AMP_LINK_KEY_LEN 32 325 typedef UINT8 AMP_LINK_KEY[AMP_LINK_KEY_LEN]; /* Dedicated AMP and GAMP Link Keys */ 326 327 #define BT_OCTET16_LEN 16 328 typedef UINT8 BT_OCTET16[BT_OCTET16_LEN]; /* octet array: size 16 */ 329 330 #define PIN_CODE_LEN 16 331 typedef UINT8 PIN_CODE[PIN_CODE_LEN]; /* Pin Code (upto 128 bits) MSB is 0 */ 332 typedef UINT8 *PIN_CODE_PTR; /* Pointer to Pin Code */ 333 334 #define DEV_CLASS_LEN 3 335 typedef UINT8 DEV_CLASS[DEV_CLASS_LEN]; /* Device class */ 336 typedef UINT8 *DEV_CLASS_PTR; /* Pointer to Device class */ 337 338 #define EXT_INQ_RESP_LEN 3 339 typedef UINT8 EXT_INQ_RESP[EXT_INQ_RESP_LEN];/* Extended Inquiry Response */ 340 typedef UINT8 *EXT_INQ_RESP_PTR; /* Pointer to Extended Inquiry Response */ 341 342 #define BD_NAME_LEN 248 343 typedef UINT8 BD_NAME[BD_NAME_LEN + 1]; /* Device name */ 344 typedef UINT8 *BD_NAME_PTR; /* Pointer to Device name */ 345 346 #define BD_FEATURES_LEN 8 347 typedef UINT8 BD_FEATURES[BD_FEATURES_LEN]; /* LMP features supported by device */ 348 349 #define BT_EVENT_MASK_LEN 8 350 typedef UINT8 BT_EVENT_MASK[BT_EVENT_MASK_LEN]; /* Event Mask */ 351 352 #define LAP_LEN 3 353 typedef UINT8 LAP[LAP_LEN]; /* IAC as passed to Inquiry (LAP) */ 354 typedef UINT8 INQ_LAP[LAP_LEN]; /* IAC as passed to Inquiry (LAP) */ 355 356 #define RAND_NUM_LEN 16 357 typedef UINT8 RAND_NUM[RAND_NUM_LEN]; 358 359 #define ACO_LEN 12 360 typedef UINT8 ACO[ACO_LEN]; /* Authenticated ciphering offset */ 361 362 #define COF_LEN 12 363 typedef UINT8 COF[COF_LEN]; /* ciphering offset number */ 364 365 typedef struct { 366 UINT8 qos_flags; /* TBD */ 367 UINT8 service_type; /* see below */ 368 UINT32 token_rate; /* bytes/second */ 369 UINT32 token_bucket_size; /* bytes */ 370 UINT32 peak_bandwidth; /* bytes/second */ 371 UINT32 latency; /* microseconds */ 372 UINT32 delay_variation; /* microseconds */ 373 } FLOW_SPEC; 374 375 /* Values for service_type */ 376 #define NO_TRAFFIC 0 377 #define BEST_EFFORT 1 378 #define GUARANTEED 2 379 380 /* Service class of the CoD */ 381 #define SERV_CLASS_NETWORKING (1 << 1) 382 #define SERV_CLASS_RENDERING (1 << 2) 383 #define SERV_CLASS_CAPTURING (1 << 3) 384 #define SERV_CLASS_OBJECT_TRANSFER (1 << 4) 385 #define SERV_CLASS_OBJECT_AUDIO (1 << 5) 386 #define SERV_CLASS_OBJECT_TELEPHONY (1 << 6) 387 #define SERV_CLASS_OBJECT_INFORMATION (1 << 7) 388 389 /* Second byte */ 390 #define SERV_CLASS_LIMITED_DISC_MODE (0x20) 391 392 /* Field size definitions. Note that byte lengths are rounded up. */ 393 #define ACCESS_CODE_BIT_LEN 72 394 #define ACCESS_CODE_BYTE_LEN 9 395 #define SHORTENED_ACCESS_CODE_BIT_LEN 68 396 397 typedef UINT8 ACCESS_CODE[ACCESS_CODE_BYTE_LEN]; 398 399 #define SYNTH_TX 1 /* want synth code to TRANSMIT at this freq */ 400 #define SYNTH_RX 2 /* want synth code to RECEIVE at this freq */ 401 402 #define SYNC_REPS 1 /* repeats of sync word transmitted to start of burst */ 403 404 /* Bluetooth CLK27 */ 405 #define BT_CLK27 (2 << 26) 406 407 /* Bluetooth CLK12 is 1.28 sec */ 408 #define BT_CLK12_TO_MS(x) ((x) * 1280) 409 #define BT_MS_TO_CLK12(x) ((x) / 1280) 410 #define BT_CLK12_TO_SLOTS(x) ((x) << 11) 411 412 /* Bluetooth CLK is 0.625 msec */ 413 #define BT_CLK_TO_MS(x) (((x) * 5 + 3) / 8) 414 #define BT_MS_TO_CLK(x) (((x) * 8 + 2) / 5) 415 416 #define BT_CLK_TO_MICROSECS(x) (((x) * 5000 + 3) / 8) 417 #define BT_MICROSECS_TO_CLK(x) (((x) * 8 + 2499) / 5000) 418 419 /* Maximum UUID size - 16 bytes, and structure to hold any type of UUID. */ 420 #define MAX_UUID_SIZE 16 421 typedef struct 422 { 423 #define LEN_UUID_16 2 424 #define LEN_UUID_32 4 425 #define LEN_UUID_128 16 426 427 UINT16 len; 428 429 union 430 { 431 UINT16 uuid16; 432 UINT32 uuid32; 433 UINT8 uuid128[MAX_UUID_SIZE]; 434 } uu; 435 436 } tBT_UUID; 437 438 #define BT_EIR_FLAGS_TYPE 0x01 439 #define BT_EIR_MORE_16BITS_UUID_TYPE 0x02 440 #define BT_EIR_COMPLETE_16BITS_UUID_TYPE 0x03 441 #define BT_EIR_MORE_32BITS_UUID_TYPE 0x04 442 #define BT_EIR_COMPLETE_32BITS_UUID_TYPE 0x05 443 #define BT_EIR_MORE_128BITS_UUID_TYPE 0x06 444 #define BT_EIR_COMPLETE_128BITS_UUID_TYPE 0x07 445 #define BT_EIR_SHORTENED_LOCAL_NAME_TYPE 0x08 446 #define BT_EIR_COMPLETE_LOCAL_NAME_TYPE 0x09 447 #define BT_EIR_TX_POWER_LEVEL_TYPE 0x0A 448 #define BT_EIR_OOB_BD_ADDR_TYPE 0x0C 449 #define BT_EIR_OOB_COD_TYPE 0x0D 450 #define BT_EIR_OOB_SSP_HASH_C_TYPE 0x0E 451 #define BT_EIR_OOB_SSP_RAND_R_TYPE 0x0F 452 #define BT_EIR_MANUFACTURER_SPECIFIC_TYPE 0xFF 453 454 #define BT_OOB_COD_SIZE 3 455 #define BT_OOB_HASH_C_SIZE 16 456 #define BT_OOB_RAND_R_SIZE 16 457 458 /* Broadcom proprietary UUIDs and reserved PSMs 459 ** 460 ** The lowest 4 bytes byte of the UUID or GUID depends on the feature. Typically, 461 ** the value of those bytes will be the PSM or SCN, but it is up to the features. 462 */ 463 #define BRCM_PROPRIETARY_UUID_BASE 0xDA, 0x23, 0x41, 0x02, 0xA3, 0xBB, 0xC1, 0x71, 0xBA, 0x09, 0x6f, 0x21 464 #define BRCM_PROPRIETARY_GUID_BASE 0xda23, 0x4102, 0xa3, 0xbb, 0xc1, 0x71, 0xba, 0x09, 0x6f, 0x21 465 466 /* We will not allocate a PSM in the reserved range to 3rd party apps 467 */ 468 #define BRCM_RESERVED_PSM_START 0x5AE1 469 #define BRCM_RESERVED_PSM_END 0x5AFF 470 471 #define BRCM_UTILITY_SERVICE_PSM 0x5AE1 472 #define BRCM_MATCHER_PSM 0x5AE3 473 474 /* Connection statistics 475 */ 476 477 /* Structure to hold connection stats */ 478 #ifndef BT_CONN_STATS_DEFINED 479 #define BT_CONN_STATS_DEFINED 480 481 /* These bits are used in the bIsConnected field */ 482 #define BT_CONNECTED_USING_BREDR 1 483 #define BT_CONNECTED_USING_AMP 2 484 485 typedef struct 486 { 487 UINT32 is_connected; 488 INT32 rssi; 489 UINT32 bytes_sent; 490 UINT32 bytes_rcvd; 491 UINT32 duration; 492 } tBT_CONN_STATS; 493 494 #endif 495 496 497 /***************************************************************************** 498 ** Low Energy definitions 499 ** 500 ** Address types 501 */ 502 #define BLE_ADDR_PUBLIC 0x00 503 #define BLE_ADDR_RANDOM 0x01 504 #define BLE_ADDR_TYPE_MASK (BLE_ADDR_RANDOM | BLE_ADDR_PUBLIC) 505 typedef UINT8 tBLE_ADDR_TYPE; 506 507 #define BT_TRANSPORT_BR_EDR 1 508 #define BT_TRANSPORT_LE 2 509 typedef UINT8 tBT_TRANSPORT; 510 511 #define BLE_ADDR_IS_STATIC(x) ((x[0] & 0xC0) == 0xC0) 512 513 typedef struct 514 { 515 tBLE_ADDR_TYPE type; 516 BD_ADDR bda; 517 } tBLE_BD_ADDR; 518 519 /* Device Types 520 */ 521 #define BT_DEVICE_TYPE_BREDR 0x01 522 #define BT_DEVICE_TYPE_BLE 0x02 523 #define BT_DEVICE_TYPE_DUMO 0x03 524 typedef UINT8 tBT_DEVICE_TYPE; 525 /*****************************************************************************/ 526 527 528 /* Define trace levels */ 529 #define BT_TRACE_LEVEL_NONE 0 /* No trace messages to be generated */ 530 #define BT_TRACE_LEVEL_ERROR 1 /* Error condition trace messages */ 531 #define BT_TRACE_LEVEL_WARNING 2 /* Warning condition trace messages */ 532 #define BT_TRACE_LEVEL_API 3 /* API traces */ 533 #define BT_TRACE_LEVEL_EVENT 4 /* Debug messages for events */ 534 #define BT_TRACE_LEVEL_DEBUG 5 /* Full debug messages */ 535 #define BT_TRACE_LEVEL_VERBOSE 6 /* Verbose debug messages */ 536 537 #define MAX_TRACE_LEVEL 6 538 539 540 /* Define New Trace Type Definition */ 541 /* TRACE_CTRL_TYPE 0x^^000000*/ 542 #define TRACE_CTRL_MASK 0xff000000 543 #define TRACE_GET_CTRL(x) ((((UINT32)(x)) & TRACE_CTRL_MASK) >> 24) 544 545 #define TRACE_CTRL_GENERAL 0x00000000 546 #define TRACE_CTRL_STR_RESOURCE 0x01000000 547 #define TRACE_CTRL_SEQ_FLOW 0x02000000 548 #define TRACE_CTRL_MAX_NUM 3 549 550 /* LAYER SPECIFIC 0x00^^0000*/ 551 #define TRACE_LAYER_MASK 0x00ff0000 552 #define TRACE_GET_LAYER(x) ((((UINT32)(x)) & TRACE_LAYER_MASK) >> 16) 553 554 #define TRACE_LAYER_NONE 0x00000000 555 #define TRACE_LAYER_USB 0x00010000 556 #define TRACE_LAYER_SERIAL 0x00020000 557 #define TRACE_LAYER_SOCKET 0x00030000 558 #define TRACE_LAYER_RS232 0x00040000 559 #define TRACE_LAYER_TRANS_MAX_NUM 5 560 #define TRACE_LAYER_TRANS_ALL 0x007f0000 561 #define TRACE_LAYER_LC 0x00050000 562 #define TRACE_LAYER_LM 0x00060000 563 #define TRACE_LAYER_HCI 0x00070000 564 #define TRACE_LAYER_L2CAP 0x00080000 565 #define TRACE_LAYER_RFCOMM 0x00090000 566 #define TRACE_LAYER_SDP 0x000a0000 567 #define TRACE_LAYER_TCS 0x000b0000 568 #define TRACE_LAYER_OBEX 0x000c0000 569 #define TRACE_LAYER_BTM 0x000d0000 570 #define TRACE_LAYER_GAP 0x000e0000 571 #define TRACE_LAYER_DUN 0x000f0000 572 #define TRACE_LAYER_GOEP 0x00100000 573 #define TRACE_LAYER_ICP 0x00110000 574 #define TRACE_LAYER_HSP2 0x00120000 575 #define TRACE_LAYER_SPP 0x00130000 576 #define TRACE_LAYER_CTP 0x00140000 577 #define TRACE_LAYER_BPP 0x00150000 578 #define TRACE_LAYER_HCRP 0x00160000 579 #define TRACE_LAYER_FTP 0x00170000 580 #define TRACE_LAYER_OPP 0x00180000 581 #define TRACE_LAYER_BTU 0x00190000 582 #define TRACE_LAYER_GKI 0x001a0000 583 #define TRACE_LAYER_BNEP 0x001b0000 584 #define TRACE_LAYER_PAN 0x001c0000 585 #define TRACE_LAYER_HFP 0x001d0000 586 #define TRACE_LAYER_HID 0x001e0000 587 #define TRACE_LAYER_BIP 0x001f0000 588 #define TRACE_LAYER_AVP 0x00200000 589 #define TRACE_LAYER_A2D 0x00210000 590 #define TRACE_LAYER_SAP 0x00220000 591 #define TRACE_LAYER_AMP 0x00230000 592 #define TRACE_LAYER_MCA 0x00240000 593 #define TRACE_LAYER_ATT 0x00250000 594 #define TRACE_LAYER_SMP 0x00260000 595 #define TRACE_LAYER_NFC 0x00270000 596 #define TRACE_LAYER_NCI 0x00280000 597 #define TRACE_LAYER_LLCP 0x00290000 598 #define TRACE_LAYER_NDEF 0x002a0000 599 #define TRACE_LAYER_RW 0x002b0000 600 #define TRACE_LAYER_CE 0x002c0000 601 #define TRACE_LAYER_P2P 0x002d0000 602 #define TRACE_LAYER_SNEP 0x002e0000 603 #define TRACE_LAYER_CHO 0x002f0000 604 #define TRACE_LAYER_NFA 0x00300000 605 606 #define TRACE_LAYER_MAX_NUM 0x0031 607 608 609 /* TRACE_ORIGINATOR 0x0000^^00*/ 610 #define TRACE_ORG_MASK 0x0000ff00 611 #define TRACE_GET_ORG(x) ((((UINT32)(x)) & TRACE_ORG_MASK) >> 8) 612 613 #define TRACE_ORG_STACK 0x00000000 614 #define TRACE_ORG_HCI_TRANS 0x00000100 615 #define TRACE_ORG_PROTO_DISP 0x00000200 616 #define TRACE_ORG_RPC 0x00000300 617 #define TRACE_ORG_GKI 0x00000400 618 #define TRACE_ORG_APPL 0x00000500 619 #define TRACE_ORG_SCR_WRAPPER 0x00000600 620 #define TRACE_ORG_SCR_ENGINE 0x00000700 621 #define TRACE_ORG_USER_SCR 0x00000800 622 #define TRACE_ORG_TESTER 0x00000900 623 #define TRACE_ORG_MAX_NUM 10 /* 32-bit mask; must be < 32 */ 624 #define TRACE_LITE_ORG_MAX_NUM 6 625 #define TRACE_ORG_ALL 0x03ff 626 #define TRACE_ORG_RPC_TRANS 0x04 627 628 #define TRACE_ORG_REG 0x00000909 629 #define TRACE_ORG_REG_SUCCESS 0x0000090a 630 631 /* TRACE_TYPE 0x000000^^*/ 632 #define TRACE_TYPE_MASK 0x000000ff 633 #define TRACE_GET_TYPE(x) (((UINT32)(x)) & TRACE_TYPE_MASK) 634 635 #define TRACE_TYPE_ERROR 0x00000000 636 #define TRACE_TYPE_WARNING 0x00000001 637 #define TRACE_TYPE_API 0x00000002 638 #define TRACE_TYPE_EVENT 0x00000003 639 #define TRACE_TYPE_DEBUG 0x00000004 640 #define TRACE_TYPE_STACK_ONLY_MAX TRACE_TYPE_DEBUG 641 #define TRACE_TYPE_TX 0x00000005 642 #define TRACE_TYPE_RX 0x00000006 643 #define TRACE_TYPE_DEBUG_ASSERT 0x00000007 644 #define TRACE_TYPE_GENERIC 0x00000008 645 #define TRACE_TYPE_REG 0x00000009 646 #define TRACE_TYPE_REG_SUCCESS 0x0000000a 647 #define TRACE_TYPE_CMD_TX 0x0000000b 648 #define TRACE_TYPE_EVT_TX 0x0000000c 649 #define TRACE_TYPE_ACL_TX 0x0000000d 650 #define TRACE_TYPE_CMD_RX 0x0000000e 651 #define TRACE_TYPE_EVT_RX 0x0000000f 652 #define TRACE_TYPE_ACL_RX 0x00000010 653 #define TRACE_TYPE_TARGET_TRACE 0x00000011 654 #define TRACE_TYPE_SCO_TX 0x00000012 655 #define TRACE_TYPE_SCO_RX 0x00000013 656 657 658 #define TRACE_TYPE_MAX_NUM 20 659 #define TRACE_TYPE_ALL 0xffff 660 661 /* Define color for script type */ 662 #define SCR_COLOR_DEFAULT 0 663 #define SCR_COLOR_TYPE_COMMENT 1 664 #define SCR_COLOR_TYPE_COMMAND 2 665 #define SCR_COLOR_TYPE_EVENT 3 666 #define SCR_COLOR_TYPE_SELECT 4 667 668 /* Define protocol trace flag values */ 669 #define SCR_PROTO_TRACE_HCI_SUMMARY 0x00000001 670 #define SCR_PROTO_TRACE_HCI_DATA 0x00000002 671 #define SCR_PROTO_TRACE_L2CAP 0x00000004 672 #define SCR_PROTO_TRACE_RFCOMM 0x00000008 673 #define SCR_PROTO_TRACE_SDP 0x00000010 674 #define SCR_PROTO_TRACE_TCS 0x00000020 675 #define SCR_PROTO_TRACE_OBEX 0x00000040 676 #define SCR_PROTO_TRACE_OAPP 0x00000080 /* OBEX Application Profile */ 677 #define SCR_PROTO_TRACE_AMP 0x00000100 678 #define SCR_PROTO_TRACE_BNEP 0x00000200 679 #define SCR_PROTO_TRACE_AVP 0x00000400 680 #define SCR_PROTO_TRACE_MCA 0x00000800 681 #define SCR_PROTO_TRACE_ATT 0x00001000 682 #define SCR_PROTO_TRACE_SMP 0x00002000 683 #define SCR_PROTO_TRACE_NCI 0x00004000 684 #define SCR_PROTO_TRACE_LLCP 0x00008000 685 #define SCR_PROTO_TRACE_NDEF 0x00010000 686 #define SCR_PROTO_TRACE_RW 0x00020000 687 #define SCR_PROTO_TRACE_CE 0x00040000 688 #define SCR_PROTO_TRACE_SNEP 0x00080000 689 #define SCR_PROTO_TRACE_CHO 0x00100000 690 #define SCR_PROTO_TRACE_ALL 0x001fffff 691 #define SCR_PROTO_TRACE_HCI_LOGGING_VSE 0x0800 /* Brcm vs event for logmsg and protocol traces */ 692 693 #define MAX_SCRIPT_TYPE 5 694 695 #define TCS_PSM_INTERCOM 5 696 #define TCS_PSM_CORDLESS 7 697 #define BT_PSM_BNEP 0x000F 698 /* Define PSMs HID uses */ 699 #define HID_PSM_CONTROL 0x0011 700 #define HID_PSM_INTERRUPT 0x0013 701 702 /* Define a function for logging */ 703 typedef void (BT_LOG_FUNC) (int trace_type, const char *fmt_str, ...); 704 705 #endif 706 707