1154 	mr = BIT_3 | BIT_2 | BIT_1 | BIT_0;  in qla1280_set_target_parameters()
1665 		err = qla1280_mailbox_command(ha, BIT_0 | BIT_1 | BIT_2, mb);  in qla1280_load_firmware_pio()
1728 				BIT_1 | BIT_0, mb);  in qla1280_load_firmware_dma()
1745 				BIT_1 | BIT_0, mb);  in qla1280_load_firmware_dma()
1790 	err = qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_start_firmware()
1800 	err = qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_start_firmware()
1866 					       BIT_3 | BIT_2 | BIT_1 | BIT_0,  in qla1280_init_rings()
1880 						 BIT_3 | BIT_2 | BIT_1 | BIT_0,  in qla1280_init_rings()
2100 	status = qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_config_bus()
2174 			     BIT_7 | BIT_3 | BIT_2 | BIT_1 | BIT_0);  in qla1280_nvram_config()
2186 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_nvram_config()
2192 	 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2207 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2216 					  BIT_1 | BIT_0, &mb[0]);  in qla1280_nvram_config()
2222 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, &mb[0]);  in qla1280_nvram_config()
2236 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2240 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2244 	mb[1] = BIT_1;	/* Data DMA Channel Burst Enable */  in qla1280_nvram_config()
2245 	mb[2] = BIT_1;	/* Command DMA Channel Burst Enable */  in qla1280_nvram_config()
2246 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2250 	status |= qla1280_mailbox_command(ha, BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2256 	status |= qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, mb);  in qla1280_nvram_config()
2546 	status = qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, &mb[0]);  in qla1280_bus_reset()
2600 	status = qla1280_mailbox_command(ha, BIT_2 | BIT_1 | BIT_0, &mb[0]);  in qla1280_device_reset()
2635 	status = qla1280_mailbox_command(ha, BIT_1 | BIT_0, &mb[0]);  in qla1280_abort_device()
3753 	else if (pkt->entry_status & BIT_1)  in qla1280_error_entry()
3773 		} else if (pkt->entry_status & BIT_1) {	/* FULL flag */  in qla1280_error_entry()
3958 	qla1280_mailbox_command(ha, BIT_6 | BIT_3 | BIT_2 | BIT_1 | BIT_0,  in qla1280_get_target_parameters()