1 /* 2 * This file is subject to the terms and conditions of the GNU General Public 3 * License. See the file "COPYING" in the main directory of this archive 4 * for more details. 5 * 6 * Derived from IRIX <sys/SN/SN0/hubio.h>, Revision 1.80. 7 * 8 * Copyright (C) 1992 - 1997, 1999 Silicon Graphics, Inc. 9 * Copyright (C) 1999 by Ralf Baechle 10 */ 11 #ifndef _ASM_SGI_SN_SN0_HUBIO_H 12 #define _ASM_SGI_SN_SN0_HUBIO_H 13 14 /* 15 * Hub I/O interface registers 16 * 17 * All registers in this file are subject to change until Hub chip tapeout. 18 * In general, the longer software name should be used when available. 19 */ 20 21 /* 22 * Slightly friendlier names for some common registers. 23 * The hardware definitions follow. 24 */ 25 #define IIO_WIDGET IIO_WID /* Widget identification */ 26 #define IIO_WIDGET_STAT IIO_WSTAT /* Widget status register */ 27 #define IIO_WIDGET_CTRL IIO_WCR /* Widget control register */ 28 #define IIO_WIDGET_TOUT IIO_WRTO /* Widget request timeout */ 29 #define IIO_WIDGET_FLUSH IIO_WTFR /* Widget target flush */ 30 #define IIO_PROTECT IIO_ILAPR /* IO interface protection */ 31 #define IIO_PROTECT_OVRRD IIO_ILAPO /* IO protect override */ 32 #define IIO_OUTWIDGET_ACCESS IIO_IOWA /* Outbound widget access */ 33 #define IIO_INWIDGET_ACCESS IIO_IIWA /* Inbound widget access */ 34 #define IIO_INDEV_ERR_MASK IIO_IIDEM /* Inbound device error mask */ 35 #define IIO_LLP_CSR IIO_ILCSR /* LLP control and status */ 36 #define IIO_LLP_LOG IIO_ILLR /* LLP log */ 37 #define IIO_XTALKCC_TOUT IIO_IXCC /* Xtalk credit count timeout*/ 38 #define IIO_XTALKTT_TOUT IIO_IXTT /* Xtalk tail timeout */ 39 #define IIO_IO_ERR_CLR IIO_IECLR /* IO error clear */ 40 #define IIO_BTE_CRB_CNT IIO_IBCN /* IO BTE CRB count */ 41 42 #define IIO_LLP_CSR_IS_UP 0x00002000 43 #define IIO_LLP_CSR_LLP_STAT_MASK 0x00003000 44 #define IIO_LLP_CSR_LLP_STAT_SHFT 12 45 46 /* key to IIO_PROTECT_OVRRD */ 47 #define IIO_PROTECT_OVRRD_KEY 0x53474972756c6573ull /* "SGIrules" */ 48 49 /* BTE register names */ 50 #define IIO_BTE_STAT_0 IIO_IBLS_0 /* Also BTE length/status 0 */ 51 #define IIO_BTE_SRC_0 IIO_IBSA_0 /* Also BTE source address 0 */ 52 #define IIO_BTE_DEST_0 IIO_IBDA_0 /* Also BTE dest. address 0 */ 53 #define IIO_BTE_CTRL_0 IIO_IBCT_0 /* Also BTE control/terminate 0 */ 54 #define IIO_BTE_NOTIFY_0 IIO_IBNA_0 /* Also BTE notification 0 */ 55 #define IIO_BTE_INT_0 IIO_IBIA_0 /* Also BTE interrupt 0 */ 56 #define IIO_BTE_OFF_0 0 /* Base offset from BTE 0 regs. */ 57 #define IIO_BTE_OFF_1 IIO_IBLS_1 - IIO_IBLS_0 /* Offset from base to BTE 1 */ 58 59 /* BTE register offsets from base */ 60 #define BTEOFF_STAT 0 61 #define BTEOFF_SRC (IIO_BTE_SRC_0 - IIO_BTE_STAT_0) 62 #define BTEOFF_DEST (IIO_BTE_DEST_0 - IIO_BTE_STAT_0) 63 #define BTEOFF_CTRL (IIO_BTE_CTRL_0 - IIO_BTE_STAT_0) 64 #define BTEOFF_NOTIFY (IIO_BTE_NOTIFY_0 - IIO_BTE_STAT_0) 65 #define BTEOFF_INT (IIO_BTE_INT_0 - IIO_BTE_STAT_0) 66 67 68 /* 69 * The following definitions use the names defined in the IO interface 70 * document for ease of reference. When possible, software should 71 * generally use the longer but clearer names defined above. 72 */ 73 74 #define IIO_BASE 0x400000 75 #define IIO_BASE_BTE0 0x410000 76 #define IIO_BASE_BTE1 0x420000 77 #define IIO_BASE_PERF 0x430000 78 #define IIO_PERF_CNT 0x430008 79 80 #define IO_PERF_SETS 32 81 82 #define IIO_WID 0x400000 /* Widget identification */ 83 #define IIO_WSTAT 0x400008 /* Widget status */ 84 #define IIO_WCR 0x400020 /* Widget control */ 85 86 #define IIO_WSTAT_ECRAZY (1ULL << 32) /* Hub gone crazy */ 87 #define IIO_WSTAT_TXRETRY (1ULL << 9) /* Hub Tx Retry timeout */ 88 #define IIO_WSTAT_TXRETRY_MASK (0x7F) 89 #define IIO_WSTAT_TXRETRY_SHFT (16) 90 #define IIO_WSTAT_TXRETRY_CNT(w) (((w) >> IIO_WSTAT_TXRETRY_SHFT) & \ 91 IIO_WSTAT_TXRETRY_MASK) 92 93 #define IIO_ILAPR 0x400100 /* Local Access Protection */ 94 #define IIO_ILAPO 0x400108 /* Protection override */ 95 #define IIO_IOWA 0x400110 /* outbound widget access */ 96 #define IIO_IIWA 0x400118 /* inbound widget access */ 97 #define IIO_IIDEM 0x400120 /* Inbound Device Error Mask */ 98 #define IIO_ILCSR 0x400128 /* LLP control and status */ 99 #define IIO_ILLR 0x400130 /* LLP Log */ 100 #define IIO_IIDSR 0x400138 /* Interrupt destination */ 101 102 #define IIO_IIBUSERR 0x1400208 /* Reads here cause a bus error. */ 103 104 /* IO Interrupt Destination Register */ 105 #define IIO_IIDSR_SENT_SHIFT 28 106 #define IIO_IIDSR_SENT_MASK 0x10000000 107 #define IIO_IIDSR_ENB_SHIFT 24 108 #define IIO_IIDSR_ENB_MASK 0x01000000 109 #define IIO_IIDSR_NODE_SHIFT 8 110 #define IIO_IIDSR_NODE_MASK 0x0000ff00 111 #define IIO_IIDSR_LVL_SHIFT 0 112 #define IIO_IIDSR_LVL_MASK 0x0000003f 113 114 115 /* GFX Flow Control Node/Widget Register */ 116 #define IIO_IGFX_0 0x400140 /* gfx node/widget register 0 */ 117 #define IIO_IGFX_1 0x400148 /* gfx node/widget register 1 */ 118 #define IIO_IGFX_W_NUM_BITS 4 /* size of widget num field */ 119 #define IIO_IGFX_W_NUM_MASK ((1<<IIO_IGFX_W_NUM_BITS)-1) 120 #define IIO_IGFX_W_NUM_SHIFT 0 121 #define IIO_IGFX_N_NUM_BITS 9 /* size of node num field */ 122 #define IIO_IGFX_N_NUM_MASK ((1<<IIO_IGFX_N_NUM_BITS)-1) 123 #define IIO_IGFX_N_NUM_SHIFT 4 124 #define IIO_IGFX_P_NUM_BITS 1 /* size of processor num field */ 125 #define IIO_IGFX_P_NUM_MASK ((1<<IIO_IGFX_P_NUM_BITS)-1) 126 #define IIO_IGFX_P_NUM_SHIFT 16 127 #define IIO_IGFX_VLD_BITS 1 /* size of valid field */ 128 #define IIO_IGFX_VLD_MASK ((1<<IIO_IGFX_VLD_BITS)-1) 129 #define IIO_IGFX_VLD_SHIFT 20 130 #define IIO_IGFX_INIT(widget, node, cpu, valid) (\ 131 (((widget) & IIO_IGFX_W_NUM_MASK) << IIO_IGFX_W_NUM_SHIFT) | \ 132 (((node) & IIO_IGFX_N_NUM_MASK) << IIO_IGFX_N_NUM_SHIFT) | \ 133 (((cpu) & IIO_IGFX_P_NUM_MASK) << IIO_IGFX_P_NUM_SHIFT) | \ 134 (((valid) & IIO_IGFX_VLD_MASK) << IIO_IGFX_VLD_SHIFT) ) 135 136 /* Scratch registers (not all bits available) */ 137 #define IIO_SCRATCH_REG0 0x400150 138 #define IIO_SCRATCH_REG1 0x400158 139 #define IIO_SCRATCH_MASK 0x0000000f00f11fff 140 141 #define IIO_SCRATCH_BIT0_0 0x0000000800000000 142 #define IIO_SCRATCH_BIT0_1 0x0000000400000000 143 #define IIO_SCRATCH_BIT0_2 0x0000000200000000 144 #define IIO_SCRATCH_BIT0_3 0x0000000100000000 145 #define IIO_SCRATCH_BIT0_4 0x0000000000800000 146 #define IIO_SCRATCH_BIT0_5 0x0000000000400000 147 #define IIO_SCRATCH_BIT0_6 0x0000000000200000 148 #define IIO_SCRATCH_BIT0_7 0x0000000000100000 149 #define IIO_SCRATCH_BIT0_8 0x0000000000010000 150 #define IIO_SCRATCH_BIT0_9 0x0000000000001000 151 #define IIO_SCRATCH_BIT0_R 0x0000000000000fff 152 153 /* IO Translation Table Entries */ 154 #define IIO_NUM_ITTES 7 /* ITTEs numbered 0..6 */ 155 /* Hw manuals number them 1..7! */ 156 157 /* 158 * As a permanent workaround for a bug in the PI side of the hub, we've 159 * redefined big window 7 as small window 0. 160 */ 161 #define HUB_NUM_BIG_WINDOW IIO_NUM_ITTES - 1 162 163 /* 164 * Use the top big window as a surrogate for the first small window 165 */ 166 #define SWIN0_BIGWIN HUB_NUM_BIG_WINDOW 167 168 #define ILCSR_WARM_RESET 0x100 169 /* 170 * The IO LLP control status register and widget control register 171 */ 172 #ifndef __ASSEMBLY__ 173 174 typedef union hubii_wid_u { 175 u64 wid_reg_value; 176 struct { 177 u64 wid_rsvd: 32, /* unused */ 178 wid_rev_num: 4, /* revision number */ 179 wid_part_num: 16, /* the widget type: hub=c101 */ 180 wid_mfg_num: 11, /* Manufacturer id (IBM) */ 181 wid_rsvd1: 1; /* Reserved */ 182 } wid_fields_s; 183 } hubii_wid_t; 184 185 186 typedef union hubii_wcr_u { 187 u64 wcr_reg_value; 188 struct { 189 u64 wcr_rsvd: 41, /* unused */ 190 wcr_e_thresh: 5, /* elasticity threshold */ 191 wcr_dir_con: 1, /* widget direct connect */ 192 wcr_f_bad_pkt: 1, /* Force bad llp pkt enable */ 193 wcr_xbar_crd: 3, /* LLP crossbar credit */ 194 wcr_rsvd1: 8, /* Reserved */ 195 wcr_tag_mode: 1, /* Tag mode */ 196 wcr_widget_id: 4; /* LLP crossbar credit */ 197 } wcr_fields_s; 198 } hubii_wcr_t; 199 200 #define iwcr_dir_con wcr_fields_s.wcr_dir_con 201 202 typedef union hubii_wstat_u { 203 u64 reg_value; 204 struct { 205 u64 rsvd1: 31, 206 crazy: 1, /* Crazy bit */ 207 rsvd2: 8, 208 llp_tx_cnt: 8, /* LLP Xmit retry counter */ 209 rsvd3: 6, 210 tx_max_rtry: 1, /* LLP Retry Timeout Signal */ 211 rsvd4: 2, 212 xt_tail_to: 1, /* Xtalk Tail Timeout */ 213 xt_crd_to: 1, /* Xtalk Credit Timeout */ 214 pending: 4; /* Pending Requests */ 215 } wstat_fields_s; 216 } hubii_wstat_t; 217 218 219 typedef union hubii_ilcsr_u { 220 u64 icsr_reg_value; 221 struct { 222 u64 icsr_rsvd: 22, /* unused */ 223 icsr_max_burst: 10, /* max burst */ 224 icsr_rsvd4: 6, /* reserved */ 225 icsr_max_retry: 10, /* max retry */ 226 icsr_rsvd3: 2, /* reserved */ 227 icsr_lnk_stat: 2, /* link status */ 228 icsr_bm8: 1, /* Bit mode 8 */ 229 icsr_llp_en: 1, /* LLP enable bit */ 230 icsr_rsvd2: 1, /* reserver */ 231 icsr_wrm_reset: 1, /* Warm reset bit */ 232 icsr_rsvd1: 2, /* Data ready offset */ 233 icsr_null_to: 6; /* Null timeout */ 234 235 } icsr_fields_s; 236 } hubii_ilcsr_t; 237 238 239 typedef union hubii_iowa_u { 240 u64 iowa_reg_value; 241 struct { 242 u64 iowa_rsvd: 48, /* unused */ 243 iowa_wxoac: 8, /* xtalk widget access bits */ 244 iowa_rsvd1: 7, /* xtalk widget access bits */ 245 iowa_w0oac: 1; /* xtalk widget access bits */ 246 } iowa_fields_s; 247 } hubii_iowa_t; 248 249 typedef union hubii_iiwa_u { 250 u64 iiwa_reg_value; 251 struct { 252 u64 iiwa_rsvd: 48, /* unused */ 253 iiwa_wxiac: 8, /* hub wid access bits */ 254 iiwa_rsvd1: 7, /* reserved */ 255 iiwa_w0iac: 1; /* hub wid0 access */ 256 } iiwa_fields_s; 257 } hubii_iiwa_t; 258 259 typedef union hubii_illr_u { 260 u64 illr_reg_value; 261 struct { 262 u64 illr_rsvd: 32, /* unused */ 263 illr_cb_cnt: 16, /* checkbit error count */ 264 illr_sn_cnt: 16; /* sequence number count */ 265 } illr_fields_s; 266 } hubii_illr_t; 267 268 /* The structures below are defined to extract and modify the ii 269 performance registers */ 270 271 /* io_perf_sel allows the caller to specify what tests will be 272 performed */ 273 typedef union io_perf_sel { 274 u64 perf_sel_reg; 275 struct { 276 u64 perf_rsvd : 48, 277 perf_icct : 8, 278 perf_ippr1 : 4, 279 perf_ippr0 : 4; 280 } perf_sel_bits; 281 } io_perf_sel_t; 282 283 /* io_perf_cnt is to extract the count from the hub registers. Due to 284 hardware problems there is only one counter, not two. */ 285 286 typedef union io_perf_cnt { 287 u64 perf_cnt; 288 struct { 289 u64 perf_rsvd1 : 32, 290 perf_rsvd2 : 12, 291 perf_cnt : 20; 292 } perf_cnt_bits; 293 } io_perf_cnt_t; 294 295 #endif /* !__ASSEMBLY__ */ 296 297 298 #define LNK_STAT_WORKING 0x2 299 300 #define IIO_LLP_CB_MAX 0xffff 301 #define IIO_LLP_SN_MAX 0xffff 302 303 /* IO PRB Entries */ 304 #define IIO_NUM_IPRBS (9) 305 #define IIO_IOPRB_0 0x400198 /* PRB entry 0 */ 306 #define IIO_IOPRB_8 0x4001a0 /* PRB entry 8 */ 307 #define IIO_IOPRB_9 0x4001a8 /* PRB entry 9 */ 308 #define IIO_IOPRB_A 0x4001b0 /* PRB entry a */ 309 #define IIO_IOPRB_B 0x4001b8 /* PRB entry b */ 310 #define IIO_IOPRB_C 0x4001c0 /* PRB entry c */ 311 #define IIO_IOPRB_D 0x4001c8 /* PRB entry d */ 312 #define IIO_IOPRB_E 0x4001d0 /* PRB entry e */ 313 #define IIO_IOPRB_F 0x4001d8 /* PRB entry f */ 314 315 316 #define IIO_IXCC 0x4001e0 /* Crosstalk credit count timeout */ 317 #define IIO_IXTCC IIO_IXCC 318 #define IIO_IMEM 0x4001e8 /* Miscellaneous Enable Mask */ 319 #define IIO_IXTT 0x4001f0 /* Crosstalk tail timeout */ 320 #define IIO_IECLR 0x4001f8 /* IO error clear */ 321 #define IIO_IBCN 0x400200 /* IO BTE CRB count */ 322 323 /* 324 * IIO_IMEM Register fields. 325 */ 326 #define IIO_IMEM_W0ESD 0x1 /* Widget 0 shut down due to error */ 327 #define IIO_IMEM_B0ESD (1 << 4) /* BTE 0 shut down due to error */ 328 #define IIO_IMEM_B1ESD (1 << 8) /* BTE 1 Shut down due to error */ 329 330 /* PIO Read address Table Entries */ 331 #define IIO_IPCA 0x400300 /* PRB Counter adjust */ 332 #define IIO_NUM_PRTES 8 /* Total number of PRB table entries */ 333 #define IIO_PRTE_0 0x400308 /* PIO Read address table entry 0 */ 334 #define IIO_PRTE(_x) (IIO_PRTE_0 + (8 * (_x))) 335 #define IIO_WIDPRTE(x) IIO_PRTE(((x) - 8)) /* widget ID to its PRTE num */ 336 #define IIO_IPDR 0x400388 /* PIO table entry deallocation */ 337 #define IIO_ICDR 0x400390 /* CRB Entry Deallocation */ 338 #define IIO_IFDR 0x400398 /* IOQ FIFO Depth */ 339 #define IIO_IIAP 0x4003a0 /* IIQ Arbitration Parameters */ 340 #define IIO_IMMR IIO_IIAP 341 #define IIO_ICMR 0x4003a8 /* CRB Management Register */ 342 #define IIO_ICCR 0x4003b0 /* CRB Control Register */ 343 #define IIO_ICTO 0x4003b8 /* CRB Time Out Register */ 344 #define IIO_ICTP 0x4003c0 /* CRB Time Out Prescalar */ 345 346 347 /* 348 * ICMR register fields 349 */ 350 #define IIO_ICMR_PC_VLD_SHFT 36 351 #define IIO_ICMR_PC_VLD_MASK (0x7fffUL << IIO_ICMR_PC_VLD_SHFT) 352 353 #define IIO_ICMR_CRB_VLD_SHFT 20 354 #define IIO_ICMR_CRB_VLD_MASK (0x7fffUL << IIO_ICMR_CRB_VLD_SHFT) 355 356 #define IIO_ICMR_FC_CNT_SHFT 16 357 #define IIO_ICMR_FC_CNT_MASK (0xf << IIO_ICMR_FC_CNT_SHFT) 358 359 #define IIO_ICMR_C_CNT_SHFT 4 360 #define IIO_ICMR_C_CNT_MASK (0xf << IIO_ICMR_C_CNT_SHFT) 361 362 #define IIO_ICMR_P_CNT_SHFT 0 363 #define IIO_ICMR_P_CNT_MASK (0xf << IIO_ICMR_P_CNT_SHFT) 364 365 #define IIO_ICMR_PRECISE (1UL << 52) 366 #define IIO_ICMR_CLR_RPPD (1UL << 13) 367 #define IIO_ICMR_CLR_RQPD (1UL << 12) 368 369 /* 370 * IIO PIO Deallocation register field masks : (IIO_IPDR) 371 */ 372 #define IIO_IPDR_PND (1 << 4) 373 374 /* 375 * IIO CRB deallocation register field masks: (IIO_ICDR) 376 */ 377 #define IIO_ICDR_PND (1 << 4) 378 379 /* 380 * IIO CRB control register Fields: IIO_ICCR 381 */ 382 #define IIO_ICCR_PENDING (0x10000) 383 #define IIO_ICCR_CMD_MASK (0xFF) 384 #define IIO_ICCR_CMD_SHFT (7) 385 #define IIO_ICCR_CMD_NOP (0x0) /* No Op */ 386 #define IIO_ICCR_CMD_WAKE (0x100) /* Reactivate CRB entry and process */ 387 #define IIO_ICCR_CMD_TIMEOUT (0x200) /* Make CRB timeout & mark invalid */ 388 #define IIO_ICCR_CMD_EJECT (0x400) /* Contents of entry written to memory 389 * via a WB 390 */ 391 #define IIO_ICCR_CMD_FLUSH (0x800) 392 393 /* 394 * CRB manipulation macros 395 * The CRB macros are slightly complicated, since there are up to 396 * four registers associated with each CRB entry. 397 */ 398 #define IIO_NUM_CRBS 15 /* Number of CRBs */ 399 #define IIO_NUM_NORMAL_CRBS 12 /* Number of regular CRB entries */ 400 #define IIO_NUM_PC_CRBS 4 /* Number of partial cache CRBs */ 401 #define IIO_ICRB_OFFSET 8 402 #define IIO_ICRB_0 0x400400 403 /* XXX - This is now tuneable: 404 #define IIO_FIRST_PC_ENTRY 12 405 */ 406 407 #define IIO_ICRB_A(_x) (IIO_ICRB_0 + (4 * IIO_ICRB_OFFSET * (_x))) 408 #define IIO_ICRB_B(_x) (IIO_ICRB_A(_x) + 1*IIO_ICRB_OFFSET) 409 #define IIO_ICRB_C(_x) (IIO_ICRB_A(_x) + 2*IIO_ICRB_OFFSET) 410 #define IIO_ICRB_D(_x) (IIO_ICRB_A(_x) + 3*IIO_ICRB_OFFSET) 411 412 /* XXX - IBUE register coming for Hub 2 */ 413 414 /* 415 * 416 * CRB Register description. 417 * 418 * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING 419 * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING 420 * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING 421 * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING 422 * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING * WARNING 423 * 424 * Many of the fields in CRB are status bits used by hardware 425 * for implementation of the protocol. It's very dangerous to 426 * mess around with the CRB registers. 427 * 428 * It's OK to read the CRB registers and try to make sense out of the 429 * fields in CRB. 430 * 431 * Updating CRB requires all activities in Hub IIO to be quiesced. 432 * otherwise, a write to CRB could corrupt other CRB entries. 433 * CRBs are here only as a back door peek to hub IIO's status. 434 * Quiescing implies no dmas no PIOs 435 * either directly from the cpu or from sn0net. 436 * this is not something that can be done easily. So, AVOID updating 437 * CRBs. 438 */ 439 440 /* 441 * Fields in CRB Register A 442 */ 443 #ifndef __ASSEMBLY__ 444 typedef union icrba_u { 445 u64 reg_value; 446 struct { 447 u64 resvd: 6, 448 stall_bte0: 1, /* Stall BTE 0 */ 449 stall_bte1: 1, /* Stall BTE 1 */ 450 error: 1, /* CRB has an error */ 451 ecode: 3, /* Error Code */ 452 lnetuce: 1, /* SN0net Uncorrectable error */ 453 mark: 1, /* CRB Has been marked */ 454 xerr: 1, /* Error bit set in xtalk header */ 455 sidn: 4, /* SIDN field from xtalk */ 456 tnum: 5, /* TNUM field in xtalk */ 457 addr: 38, /* Address of request */ 458 valid: 1, /* Valid status */ 459 iow: 1; /* IO Write operation */ 460 } icrba_fields_s; 461 } icrba_t; 462 463 /* This is an alternate typedef for the HUB1 CRB A in order to allow 464 runtime selection of the format based on the REV_ID field of the 465 NI_STATUS_REV_ID register. */ 466 typedef union h1_icrba_u { 467 u64 reg_value; 468 469 struct { 470 u64 resvd: 6, 471 unused: 1, /* Unused but RW!! */ 472 error: 1, /* CRB has an error */ 473 ecode: 4, /* Error Code */ 474 lnetuce: 1, /* SN0net Uncorrectable error */ 475 mark: 1, /* CRB Has been marked */ 476 xerr: 1, /* Error bit set in xtalk header */ 477 sidn: 4, /* SIDN field from xtalk */ 478 tnum: 5, /* TNUM field in xtalk */ 479 addr: 38, /* Address of request */ 480 valid: 1, /* Valid status */ 481 iow: 1; /* IO Write operation */ 482 } h1_icrba_fields_s; 483 } h1_icrba_t; 484 485 /* XXX - Is this still right? Check the spec. */ 486 #define ICRBN_A_CERR_SHFT 54 487 #define ICRBN_A_ERR_MASK 0x3ff 488 489 #endif /* !__ASSEMBLY__ */ 490 491 #define IIO_ICRB_ADDR_SHFT 2 /* Shift to get proper address */ 492 493 /* 494 * values for "ecode" field 495 */ 496 #define IIO_ICRB_ECODE_DERR 0 /* Directory error due to IIO access */ 497 #define IIO_ICRB_ECODE_PERR 1 /* Poison error on IO access */ 498 #define IIO_ICRB_ECODE_WERR 2 /* Write error by IIO access 499 * e.g. WINV to a Read only line. 500 */ 501 #define IIO_ICRB_ECODE_AERR 3 /* Access error caused by IIO access */ 502 #define IIO_ICRB_ECODE_PWERR 4 /* Error on partial write */ 503 #define IIO_ICRB_ECODE_PRERR 5 /* Error on partial read */ 504 #define IIO_ICRB_ECODE_TOUT 6 /* CRB timeout before deallocating */ 505 #define IIO_ICRB_ECODE_XTERR 7 /* Incoming xtalk pkt had error bit */ 506 507 508 509 /* 510 * Fields in CRB Register B 511 */ 512 #ifndef __ASSEMBLY__ 513 typedef union icrbb_u { 514 u64 reg_value; 515 struct { 516 u64 rsvd1: 5, 517 btenum: 1, /* BTE to which entry belongs to */ 518 cohtrans: 1, /* Coherent transaction */ 519 xtsize: 2, /* Xtalk operation size 520 * 0: Double Word 521 * 1: 32 Bytes. 522 * 2: 128 Bytes, 523 * 3: Reserved. 524 */ 525 srcnode: 9, /* Source Node ID */ 526 srcinit: 2, /* Source Initiator: 527 * See below for field values. 528 */ 529 useold: 1, /* Use OLD command for processing */ 530 imsgtype: 2, /* Incoming message type 531 * see below for field values 532 */ 533 imsg: 8, /* Incoming message */ 534 initator: 3, /* Initiator of original request 535 * See below for field values. 536 */ 537 reqtype: 5, /* Identifies type of request 538 * See below for field values. 539 */ 540 rsvd2: 7, 541 ackcnt: 11, /* Invalidate ack count */ 542 resp: 1, /* data response given to processor */ 543 ack: 1, /* indicates data ack received */ 544 hold: 1, /* entry is gathering inval acks */ 545 wb_pend:1, /* waiting for writeback to complete */ 546 intvn: 1, /* Intervention */ 547 stall_ib: 1, /* Stall Ibuf (from crosstalk) */ 548 stall_intr: 1; /* Stall internal interrupts */ 549 } icrbb_field_s; 550 } icrbb_t; 551 552 /* This is an alternate typedef for the HUB1 CRB B in order to allow 553 runtime selection of the format based on the REV_ID field of the 554 NI_STATUS_REV_ID register. */ 555 typedef union h1_icrbb_u { 556 u64 reg_value; 557 struct { 558 u64 rsvd1: 5, 559 btenum: 1, /* BTE to which entry belongs to */ 560 cohtrans: 1, /* Coherent transaction */ 561 xtsize: 2, /* Xtalk operation size 562 * 0: Double Word 563 * 1: 32 Bytes. 564 * 2: 128 Bytes, 565 * 3: Reserved. 566 */ 567 srcnode: 9, /* Source Node ID */ 568 srcinit: 2, /* Source Initiator: 569 * See below for field values. 570 */ 571 useold: 1, /* Use OLD command for processing */ 572 imsgtype: 2, /* Incoming message type 573 * see below for field values 574 */ 575 imsg: 8, /* Incoming message */ 576 initator: 3, /* Initiator of original request 577 * See below for field values. 578 */ 579 rsvd2: 1, 580 pcache: 1, /* entry belongs to partial cache */ 581 reqtype: 5, /* Identifies type of request 582 * See below for field values. 583 */ 584 stl_ib: 1, /* stall Ibus coming from xtalk */ 585 stl_intr: 1, /* Stall internal interrupts */ 586 stl_bte0: 1, /* Stall BTE 0 */ 587 stl_bte1: 1, /* Stall BTE 1 */ 588 intrvn: 1, /* Req was target of intervention */ 589 ackcnt: 11, /* Invalidate ack count */ 590 resp: 1, /* data response given to processor */ 591 ack: 1, /* indicates data ack received */ 592 hold: 1, /* entry is gathering inval acks */ 593 wb_pend:1, /* waiting for writeback to complete */ 594 sleep: 1, /* xtalk req sleeping till IO-sync */ 595 pnd_reply: 1, /* replies not issed due to IOQ full */ 596 pnd_req: 1; /* reqs not issued due to IOQ full */ 597 } h1_icrbb_field_s; 598 } h1_icrbb_t; 599 600 601 #define b_imsgtype icrbb_field_s.imsgtype 602 #define b_btenum icrbb_field_s.btenum 603 #define b_cohtrans icrbb_field_s.cohtrans 604 #define b_xtsize icrbb_field_s.xtsize 605 #define b_srcnode icrbb_field_s.srcnode 606 #define b_srcinit icrbb_field_s.srcinit 607 #define b_imsgtype icrbb_field_s.imsgtype 608 #define b_imsg icrbb_field_s.imsg 609 #define b_initiator icrbb_field_s.initiator 610 611 #endif /* !__ASSEMBLY__ */ 612 613 /* 614 * values for field xtsize 615 */ 616 #define IIO_ICRB_XTSIZE_DW 0 /* Xtalk operation size is 8 bytes */ 617 #define IIO_ICRB_XTSIZE_32 1 /* Xtalk operation size is 32 bytes */ 618 #define IIO_ICRB_XTSIZE_128 2 /* Xtalk operation size is 128 bytes */ 619 620 /* 621 * values for field srcinit 622 */ 623 #define IIO_ICRB_PROC0 0 /* Source of request is Proc 0 */ 624 #define IIO_ICRB_PROC1 1 /* Source of request is Proc 1 */ 625 #define IIO_ICRB_GB_REQ 2 /* Source is Guaranteed BW request */ 626 #define IIO_ICRB_IO_REQ 3 /* Source is Normal IO request */ 627 628 /* 629 * Values for field imsgtype 630 */ 631 #define IIO_ICRB_IMSGT_XTALK 0 /* Incoming Meessage from Xtalk */ 632 #define IIO_ICRB_IMSGT_BTE 1 /* Incoming message from BTE */ 633 #define IIO_ICRB_IMSGT_SN0NET 2 /* Incoming message from SN0 net */ 634 #define IIO_ICRB_IMSGT_CRB 3 /* Incoming message from CRB ??? */ 635 636 /* 637 * values for field initiator. 638 */ 639 #define IIO_ICRB_INIT_XTALK 0 /* Message originated in xtalk */ 640 #define IIO_ICRB_INIT_BTE0 0x1 /* Message originated in BTE 0 */ 641 #define IIO_ICRB_INIT_SN0NET 0x2 /* Message originated in SN0net */ 642 #define IIO_ICRB_INIT_CRB 0x3 /* Message originated in CRB ? */ 643 #define IIO_ICRB_INIT_BTE1 0x5 /* MEssage originated in BTE 1 */ 644 645 /* 646 * Values for field reqtype. 647 */ 648 /* XXX - Need to fix this for Hub 2 */ 649 #define IIO_ICRB_REQ_DWRD 0 /* Request type double word */ 650 #define IIO_ICRB_REQ_QCLRD 1 /* Request is Qrtr Caceh line Rd */ 651 #define IIO_ICRB_REQ_BLKRD 2 /* Request is block read */ 652 #define IIO_ICRB_REQ_RSHU 6 /* Request is BTE block read */ 653 #define IIO_ICRB_REQ_REXU 7 /* request is BTE Excl Read */ 654 #define IIO_ICRB_REQ_RDEX 8 /* Request is Read Exclusive */ 655 #define IIO_ICRB_REQ_WINC 9 /* Request is Write Invalidate */ 656 #define IIO_ICRB_REQ_BWINV 10 /* Request is BTE Winv */ 657 #define IIO_ICRB_REQ_PIORD 11 /* Request is PIO read */ 658 #define IIO_ICRB_REQ_PIOWR 12 /* Request is PIO Write */ 659 #define IIO_ICRB_REQ_PRDM 13 /* Request is Fetch&Op */ 660 #define IIO_ICRB_REQ_PWRM 14 /* Request is Store &Op */ 661 #define IIO_ICRB_REQ_PTPWR 15 /* Request is Peer to peer */ 662 #define IIO_ICRB_REQ_WB 16 /* Request is Write back */ 663 #define IIO_ICRB_REQ_DEX 17 /* Retained DEX Cache line */ 664 665 /* 666 * Fields in CRB Register C 667 */ 668 669 #ifndef __ASSEMBLY__ 670 671 typedef union icrbc_s { 672 u64 reg_value; 673 struct { 674 u64 rsvd: 6, 675 sleep: 1, 676 pricnt: 4, /* Priority count sent with Read req */ 677 pripsc: 4, /* Priority Pre scalar */ 678 bteop: 1, /* BTE Operation */ 679 push_be: 34, /* Push address Byte enable 680 * Holds push addr, if CRB is for BTE 681 * If CRB belongs to Partial cache, 682 * this contains byte enables bits 683 * ([47:46] = 0) 684 */ 685 suppl: 11, /* Supplemental field */ 686 barrop: 1, /* Barrier Op bit set in xtalk req */ 687 doresp: 1, /* Xtalk req needs a response */ 688 gbr: 1; /* GBR bit set in xtalk packet */ 689 } icrbc_field_s; 690 } icrbc_t; 691 692 #define c_pricnt icrbc_field_s.pricnt 693 #define c_pripsc icrbc_field_s.pripsc 694 #define c_bteop icrbc_field_s.bteop 695 #define c_bteaddr icrbc_field_s.push_be /* push_be field has 2 names */ 696 #define c_benable icrbc_field_s.push_be /* push_be field has 2 names */ 697 #define c_suppl icrbc_field_s.suppl 698 #define c_barrop icrbc_field_s.barrop 699 #define c_doresp icrbc_field_s.doresp 700 #define c_gbr icrbc_field_s.gbr 701 #endif /* !__ASSEMBLY__ */ 702 703 /* 704 * Fields in CRB Register D 705 */ 706 707 #ifndef __ASSEMBLY__ 708 typedef union icrbd_s { 709 u64 reg_value; 710 struct { 711 u64 rsvd: 38, 712 toutvld: 1, /* Timeout in progress for this CRB */ 713 ctxtvld: 1, /* Context field below is valid */ 714 rsvd2: 1, 715 context: 15, /* Bit vector: 716 * Has a bit set for each CRB entry 717 * which needs to be deallocated 718 * before this CRB entry is processed. 719 * Set only for barrier operations. 720 */ 721 timeout: 8; /* Timeout Upper 8 bits */ 722 } icrbd_field_s; 723 } icrbd_t; 724 725 #define icrbd_toutvld icrbd_field_s.toutvld 726 #define icrbd_ctxtvld icrbd_field_s.ctxtvld 727 #define icrbd_context icrbd_field_s.context 728 729 730 typedef union hubii_ifdr_u { 731 u64 hi_ifdr_value; 732 struct { 733 u64 ifdr_rsvd: 49, 734 ifdr_maxrp: 7, 735 ifdr_rsvd1: 1, 736 ifdr_maxrq: 7; 737 } hi_ifdr_fields; 738 } hubii_ifdr_t; 739 740 #endif /* !__ASSEMBLY__ */ 741 742 /* 743 * Hardware designed names for the BTE control registers. 744 */ 745 #define IIO_IBLS_0 0x410000 /* BTE length/status 0 */ 746 #define IIO_IBSA_0 0x410008 /* BTE source address 0 */ 747 #define IIO_IBDA_0 0x410010 /* BTE destination address 0 */ 748 #define IIO_IBCT_0 0x410018 /* BTE control/terminate 0 */ 749 #define IIO_IBNA_0 0x410020 /* BTE notification address 0 */ 750 #define IIO_IBNR_0 IIO_IBNA_0 751 #define IIO_IBIA_0 0x410028 /* BTE interrupt address 0 */ 752 753 #define IIO_IBLS_1 0x420000 /* BTE length/status 1 */ 754 #define IIO_IBSA_1 0x420008 /* BTE source address 1 */ 755 #define IIO_IBDA_1 0x420010 /* BTE destination address 1 */ 756 #define IIO_IBCT_1 0x420018 /* BTE control/terminate 1 */ 757 #define IIO_IBNA_1 0x420020 /* BTE notification address 1 */ 758 #define IIO_IBNR_1 IIO_IBNA_1 759 #define IIO_IBIA_1 0x420028 /* BTE interrupt address 1 */ 760 761 /* 762 * More miscellaneous registers 763 */ 764 #define IIO_IPCR 0x430000 /* Performance Control */ 765 #define IIO_IPPR 0x430008 /* Performance Profiling */ 766 767 /* 768 * IO Error Clear register bit field definitions 769 */ 770 #define IECLR_BTE1 (1 << 18) /* clear bte error 1 ??? */ 771 #define IECLR_BTE0 (1 << 17) /* clear bte error 0 ??? */ 772 #define IECLR_CRAZY (1 << 16) /* clear crazy bit in wstat reg */ 773 #define IECLR_PRB_F (1 << 15) /* clear err bit in PRB_F reg */ 774 #define IECLR_PRB_E (1 << 14) /* clear err bit in PRB_E reg */ 775 #define IECLR_PRB_D (1 << 13) /* clear err bit in PRB_D reg */ 776 #define IECLR_PRB_C (1 << 12) /* clear err bit in PRB_C reg */ 777 #define IECLR_PRB_B (1 << 11) /* clear err bit in PRB_B reg */ 778 #define IECLR_PRB_A (1 << 10) /* clear err bit in PRB_A reg */ 779 #define IECLR_PRB_9 (1 << 9) /* clear err bit in PRB_9 reg */ 780 #define IECLR_PRB_8 (1 << 8) /* clear err bit in PRB_8 reg */ 781 #define IECLR_PRB_0 (1 << 0) /* clear err bit in PRB_0 reg */ 782 783 /* 784 * IO PIO Read Table Entry format 785 */ 786 787 #ifndef __ASSEMBLY__ 788 789 typedef union iprte_a { 790 u64 entry; 791 struct { 792 u64 rsvd1 : 7, /* Reserved field */ 793 valid : 1, /* Maps to a timeout entry */ 794 rsvd2 : 1, 795 srcnode : 9, /* Node which did this PIO */ 796 initiator : 2, /* If T5A or T5B or IO */ 797 rsvd3 : 3, 798 addr : 38, /* Physical address of PIO */ 799 rsvd4 : 3; 800 } iprte_fields; 801 } iprte_a_t; 802 803 #define iprte_valid iprte_fields.valid 804 #define iprte_timeout iprte_fields.timeout 805 #define iprte_srcnode iprte_fields.srcnode 806 #define iprte_init iprte_fields.initiator 807 #define iprte_addr iprte_fields.addr 808 809 #endif /* !__ASSEMBLY__ */ 810 811 #define IPRTE_ADDRSHFT 3 812 813 /* 814 * Hub IIO PRB Register format. 815 */ 816 817 #ifndef __ASSEMBLY__ 818 /* 819 * Note: Fields bnakctr, anakctr, xtalkctrmode, ovflow fields are 820 * "Status" fields, and should only be used in case of clean up after errors. 821 */ 822 823 typedef union iprb_u { 824 u64 reg_value; 825 struct { 826 u64 rsvd1: 15, 827 error: 1, /* Widget rcvd wr resp pkt w/ error */ 828 ovflow: 5, /* Overflow count. perf measurement */ 829 fire_and_forget: 1, /* Launch Write without response */ 830 mode: 2, /* Widget operation Mode */ 831 rsvd2: 2, 832 bnakctr: 14, 833 rsvd3: 2, 834 anakctr: 14, 835 xtalkctr: 8; 836 } iprb_fields_s; 837 } iprb_t; 838 839 #define iprb_regval reg_value 840 841 #define iprb_error iprb_fields_s.error 842 #define iprb_ovflow iprb_fields_s.ovflow 843 #define iprb_ff iprb_fields_s.fire_and_forget 844 #define iprb_mode iprb_fields_s.mode 845 #define iprb_bnakctr iprb_fields_s.bnakctr 846 #define iprb_anakctr iprb_fields_s.anakctr 847 #define iprb_xtalkctr iprb_fields_s.xtalkctr 848 849 #endif /* !__ASSEMBLY__ */ 850 851 /* 852 * values for mode field in iprb_t. 853 * For details of the meanings of NAK and Accept, refer the PIO flow 854 * document 855 */ 856 #define IPRB_MODE_NORMAL (0) 857 #define IPRB_MODE_COLLECT_A (1) /* PRB in collect A mode */ 858 #define IPRB_MODE_SERVICE_A (2) /* NAK B and Accept A */ 859 #define IPRB_MODE_SERVICE_B (3) /* NAK A and Accept B */ 860 861 /* 862 * IO CRB entry C_A to E_A : Partial (cache) CRBS 863 */ 864 #ifndef __ASSEMBLY__ 865 typedef union icrbp_a { 866 u64 ip_reg; /* the entire register value */ 867 struct { 868 u64 error: 1, /* 63, error occurred */ 869 ln_uce: 1, /* 62: uncorrectable memory */ 870 ln_ae: 1, /* 61: protection violation */ 871 ln_werr:1, /* 60: write access error */ 872 ln_aerr:1, /* 59: sn0net: Address error */ 873 ln_perr:1, /* 58: sn0net: poison error */ 874 timeout:1, /* 57: CRB timed out */ 875 l_bdpkt:1, /* 56: truncated pkt on sn0net */ 876 c_bdpkt:1, /* 55: truncated pkt on xtalk */ 877 c_err: 1, /* 54: incoming xtalk req, err set*/ 878 rsvd1: 12, /* 53-42: reserved */ 879 valid: 1, /* 41: Valid status */ 880 sidn: 4, /* 40-37: SIDN field of xtalk rqst */ 881 tnum: 5, /* 36-32: TNUM of xtalk request */ 882 bo: 1, /* 31: barrier op set in xtalk rqst*/ 883 resprqd:1, /* 30: xtalk rqst requires response*/ 884 gbr: 1, /* 29: gbr bit set in xtalk rqst */ 885 size: 2, /* 28-27: size of xtalk request */ 886 excl: 4, /* 26-23: exclusive bit(s) */ 887 stall: 3, /* 22-20: stall (xtalk, bte 0/1) */ 888 intvn: 1, /* 19: rqst target of intervention*/ 889 resp: 1, /* 18: Data response given to t5 */ 890 ack: 1, /* 17: Data ack received. */ 891 hold: 1, /* 16: crb gathering invalidate acks*/ 892 wb: 1, /* 15: writeback pending. */ 893 ack_cnt:11, /* 14-04: counter of invalidate acks*/ 894 tscaler:4; /* 03-00: Timeout prescaler */ 895 } ip_fmt; 896 } icrbp_a_t; 897 898 #endif /* !__ASSEMBLY__ */ 899 900 /* 901 * A couple of defines to go with the above structure. 902 */ 903 #define ICRBP_A_CERR_SHFT 54 904 #define ICRBP_A_ERR_MASK 0x3ff 905 906 #ifndef __ASSEMBLY__ 907 typedef union hubii_idsr { 908 u64 iin_reg; 909 struct { 910 u64 rsvd1 : 35, 911 isent : 1, 912 rsvd2 : 3, 913 ienable: 1, 914 rsvd : 7, 915 node : 9, 916 rsvd4 : 1, 917 level : 7; 918 } iin_fmt; 919 } hubii_idsr_t; 920 #endif /* !__ASSEMBLY__ */ 921 922 /* 923 * IO BTE Length/Status (IIO_IBLS) register bit field definitions 924 */ 925 #define IBLS_BUSY (0x1 << 20) 926 #define IBLS_ERROR_SHFT 16 927 #define IBLS_ERROR (0x1 << IBLS_ERROR_SHFT) 928 #define IBLS_LENGTH_MASK 0xffff 929 930 /* 931 * IO BTE Control/Terminate register (IBCT) register bit field definitions 932 */ 933 #define IBCT_POISON (0x1 << 8) 934 #define IBCT_NOTIFY (0x1 << 4) 935 #define IBCT_ZFIL_MODE (0x1 << 0) 936 937 /* 938 * IO BTE Interrupt Address Register (IBIA) register bit field definitions 939 */ 940 #define IBIA_LEVEL_SHFT 16 941 #define IBIA_LEVEL_MASK (0x7f << IBIA_LEVEL_SHFT) 942 #define IBIA_NODE_ID_SHFT 0 943 #define IBIA_NODE_ID_MASK (0x1ff) 944 945 /* 946 * Miscellaneous hub constants 947 */ 948 949 /* Number of widgets supported by hub */ 950 #define HUB_NUM_WIDGET 9 951 #define HUB_WIDGET_ID_MIN 0x8 952 #define HUB_WIDGET_ID_MAX 0xf 953 954 #define HUB_WIDGET_PART_NUM 0xc101 955 #define MAX_HUBS_PER_XBOW 2 956 957 /* 958 * Get a hub's widget id from widget control register 959 */ 960 #define IIO_WCR_WID_GET(nasid) (REMOTE_HUB_L(nasid, III_WCR) & 0xf) 961 #define IIO_WST_ERROR_MASK (UINT64_CAST 1 << 32) /* Widget status error */ 962 963 /* 964 * Number of credits Hub widget has while sending req/response to 965 * xbow. 966 * Value of 3 is required by Xbow 1.1 967 * We may be able to increase this to 4 with Xbow 1.2. 968 */ 969 #define HUBII_XBOW_CREDIT 3 970 #define HUBII_XBOW_REV2_CREDIT 4 971 972 #endif /* _ASM_SGI_SN_SN0_HUBIO_H */ 973