Searched refs:LED (Results 1 – 25 of 25) sorted by relevance
9 bool "LED Support"11 Say Y to enable Linux LED support. This allows control of supported20 tristate "LED Class Support"25 comment "LED drivers"28 tristate "LED Support for Marvell 88PM860x PMIC"32 This option enables support for on-chip LED drivers found on Marvell36 tristate "LED Support using Atmel PWM outputs"54 tristate "LED support for LM3533"67 tristate "LED support for LM3642 Chip"74 white LED.[all …]
2 bool "LED Trigger support"12 tristate "LED Timer Trigger"16 via sysfs. Some LED hardware can be programmed to start17 blinking the LED without any further software interaction.23 tristate "LED One-shot Trigger"29 or on dense events, where this blinks the LED at constant rate if37 bool "LED IDE Disk Trigger"45 tristate "LED Heartbeat Trigger"54 tristate "LED backlight Trigger"63 bool "LED CPU Trigger"[all …]
102 MSP_GPIO(0, LED), MSP_GPIO(1, LED),103 MSP_GPIO(2, LED), MSP_GPIO(3, LED),104 MSP_GPIO(4, LED), MSP_GPIO(5, LED),105 MSP_GPIO(6, LED), MSP_GPIO(7, LED),
367 VEXPRESS_SYSREG_GPIO(LED0, SYS_LED, LED(0)),368 VEXPRESS_SYSREG_GPIO(LED1, SYS_LED, LED(1)),369 VEXPRESS_SYSREG_GPIO(LED2, SYS_LED, LED(2)),370 VEXPRESS_SYSREG_GPIO(LED3, SYS_LED, LED(3)),371 VEXPRESS_SYSREG_GPIO(LED4, SYS_LED, LED(4)),372 VEXPRESS_SYSREG_GPIO(LED5, SYS_LED, LED(5)),373 VEXPRESS_SYSREG_GPIO(LED6, SYS_LED, LED(6)),374 VEXPRESS_SYSREG_GPIO(LED7, SYS_LED, LED(7)),
181 tristate "HTC PASIC3 LED/DS1WM chip support"185 This core driver provides register access for the LED/DS1WM732 high-power "white LED driver". This boost converter is778 tristate "TI TPS65217 Power Management / White LED chips"784 Power Management / White LED chips.948 additional drivers must be enabled in order to use the LED,
121 MFP_FALCON(GPIO9, LED, GPIO, NONE, NONE),122 MFP_FALCON(GPIO10, LED, GPIO, NONE, NONE),123 MFP_FALCON(GPIO11, LED, GPIO, NONE, NONE),124 MFP_FALCON(GPIO12, LED, GPIO, NONE, NONE),125 MFP_FALCON(GPIO13, LED, GPIO, NONE, NONE),126 MFP_FALCON(GPIO14, LED, GPIO, NONE, NONE),191 GRP_MUX("bootled", LED, pins_bled),
129 bool "Chassis LCD and LED support"137 This has nothing to do with LED State support for A and E class.146 That includes support for LED State front panel as found on E147 class, and support for the GSP Virtual Front Panel (LED State and152 shown by the LED/LCD driver.153 This driver updates the state panel (LED and/or LCD) upon system
84 turn off the LED. Not all cameras support this though (the 645 and 646110 This settings takes 2 integers, that define the on/off time for the LED112 this is let the LED blink while the camera is in use. This:116 will blink the LED once every second. But with:120 the LED never goes on, making it suitable for silent surveillance.122 By default the camera's LED is on solid while in use, and turned off127 the LED cannot be controlled.130 open the camera device. Until then, the LED remains on.
91 bool "Support for the Power/iBook front LED"96 Support the front LED on Power/iBooks as a generic LED that can99 and the ide-disk LED trigger and configure appropriately through103 bool "Use front LED as IDE LED by default"109 This option makes the front LED default to the IDE trigger
56 bool "Enable LED triggers for Netlink based drivers"60 This option adds two LED triggers for packet receive and transmit
267 #define CHECK_LED(LK, VAR_ON, VAR_OFF, LED, BITS) do { \ argument268 if (test_bit(LED, (LK)->dev->led)) \
187 tristate "TWL4030/6030 PWM support for LED drivers"190 Generic PWM framework driver for TWL4030/6030 LED terminals.
440 * Power LED (toward the middle of the adapter)441 - This LED indicates power has been applied, and the card is445 * Transmit/Receive LED (closer to the edge of the adapter)446 - This LED flashes when it detects transmit or receive packets.452 * LEDs indicate normal operation with the Power LED453 steady-on or blinking rapidly and Transmit/Receive LED flashing, but no
302 bool "LED Support for Xbox360 controller 'BigX' LED"305 This option enables support for the LED which surrounds the Big X on
63 This is the driver for the 7-segment display and LED present on
36 exposes the mail LED and LCD backlight.385 Overriding LED state on ThinkPads can mask important390 LED control on the ThinkPad is write-only (with very few393 be lost when one changes LED state.396 and the driver will allow control of every LED, including739 function keys, wireless LED, LCD backlight level.
37 # LED support
42 tristate "USB 7-Segment LED Display"83 tristate "USB LED driver support"
116 #define LED 0x08 /* output to pin LED */ macro2513 reg01 |= LED; in sd_stopN()2515 reg01 &= ~(LED | V_TX_EN); in sd_stopN()2559 reg01 |= LED; in sd_stopN()
676 tristate "ThingM blink(1) USB RGB LED"680 Support for the ThingM blink(1) USB RGB LED. This driver registers a681 Linux LED class instance, plus additional sysfs attributes to control
1469 INPUT_DEV_CAP_ATTR(LED, led);1637 INPUT_DO_TOGGLE(dev, LED, led, activate); in input_dev_toggle()1959 INPUT_CLEANSE_BITMASK(dev, LED, led); in input_cleanse_bitmasks()
126 * On Rev A. hardware, the busy LED is only128 * and re-selections. Make the LED status620 * On Rev A. hardware, the busy LED is only622 * and re-selections. Make the LED status673 * On Rev A. hardware, the busy LED is only675 * and re-selections. Make the LED status
385 This supports TI LM3639 Backlight + 1.5A Flash LED Driver
804 LED = 0x18, enumerator
352 rotation. The dial also acts as a pushbutton. The base contains an LED