Home
last modified time | relevance | path

Searched refs:selecting (Results 1 – 24 of 24) sorted by relevance

/drivers/scsi/
Din2000.c459 if (hostdata->selecting || hostdata->connected) { in DEF_SCSI_QCMD()
576 hostdata->selecting = cmd; in DEF_SCSI_QCMD()
1072 cmd = (Scsi_Cmnd *) hostdata->selecting; /* get a valid cmd */ in in2000_intr()
1074 hostdata->selecting = NULL; in in2000_intr()
1094 hostdata->connected = cmd = (Scsi_Cmnd *) hostdata->selecting; in in2000_intr()
1096 hostdata->selecting = NULL; in in2000_intr()
1494 if (hostdata->selecting) { in in2000_intr()
1495 cmd = (Scsi_Cmnd *) hostdata->selecting; in in2000_intr()
1496 hostdata->selecting = NULL; in in2000_intr()
1664 hostdata->selecting = NULL; in in2000_bus_reset()
[all …]
Dwd33c93.c492 if (hostdata->selecting || hostdata->connected) { in DEF_SCSI_QCMD()
612 hostdata->selecting = cmd; in DEF_SCSI_QCMD()
860 cmd = (struct scsi_cmnd *) hostdata->selecting; /* get a valid cmd */ in wd33c93_intr()
861 hostdata->selecting = NULL; in wd33c93_intr()
893 (struct scsi_cmnd *) hostdata->selecting; in wd33c93_intr()
894 hostdata->selecting = NULL; in wd33c93_intr()
1353 if (hostdata->selecting) { in wd33c93_intr()
1354 cmd = (struct scsi_cmnd *) hostdata->selecting; in wd33c93_intr()
1355 hostdata->selecting = NULL; in wd33c93_intr()
1594 hostdata->selecting = NULL; in wd33c93_host_reset()
[all …]
Dmac53c94.c37 selecting, enumerator
177 state->phase = selecting; in mac53c94_start()
248 case selecting: in mac53c94_interrupt()
DNCR5380.c1042 if (!hostdata->connected && !hostdata->selecting) { in DEF_SCSI_QCMD()
1081 hostdata->selecting = NULL; in DEF_SCSI_QCMD()
1105 if (hostdata->selecting) { in DEF_SCSI_QCMD()
1106 tmp = (Scsi_Cmnd *) hostdata->selecting; in DEF_SCSI_QCMD()
1301 if (hostdata->selecting) in NCR5380_select()
1441 hostdata->selecting = cmd; in NCR5380_select()
1457 hostdata->selecting = NULL;/* clear this pointer, because we passed the in NCR5380_select()
Dwd33c93.h242 volatile struct scsi_cmnd *selecting; /* trying to select this command */ member
Din2000.h287 volatile Scsi_Cmnd *selecting; /* trying to select this command */ member
DNCR5380.h277 volatile Scsi_Cmnd *selecting; member
Daha152x.c348 selecting = 0x0002, /* target is beeing selected */ enumerator
950 if(CURRENT_SC->SCp.phase & selecting) { in setup_expected_interrupts()
1643 CURRENT_SC->SCp.phase |= selecting; in busfree_run()
1677 CURRENT_SC->SCp.phase &= ~(selecting|not_issued); in seldo_run()
1721 CURRENT_SC->SCp.phase &= ~selecting; in selto_run()
2425 } else if(stat0 & SELDO && CURRENT_SC && (CURRENT_SC->SCp.phase & selecting)) { in update_state()
2928 if (ptr->SCp.phase & selecting) in show_command()
2998 if (ptr->SCp.phase & selecting) in get_command()
Dmesh.c105 selecting, enumerator
763 case selecting: in start_phase()
1114 if (ms->phase > selecting && (in_8(&mr->bus_status1) & BS1_BSY)) { in handle_error()
1544 case selecting: in cmd_complete()
D53c700.scr163 ; Basically tell the selecting device that there's nothing here
D53c700_d.h_shipped199 ; Basically tell the selecting device that there's nothing here
/drivers/media/usb/pwc/
DKconfig27 The built-in microphone is enabled by selecting USB Audio support.
/drivers/media/platform/s5p-tv/
DKconfig14 Say Y here to enable selecting the TV output devices for
/drivers/media/platform/
DKconfig136 Say Y here to enable selecting drivers for V4L devices that
/drivers/media/usb/gspca/
DKconfig6 Say Y here if you want to enable selecting webcams based
/drivers/mtd/nand/
DKconfig130 hardware bug. Please check your OMAP datasheet before selecting this
/drivers/media/radio/
DKconfig11 Say Y here to enable selecting AM/FM radio adapters.
/drivers/scsi/aic7xxx_old/
Daic7xxx.seq87 * are selecting, keep polling the current channel util
1005 * the target selecting 8bit or asynchronous transfer, otherwise just ignore
Daic7xxx.reg417 * Upper four bits are the device id. The ONEBIT is set when the re/selecting
/drivers/scsi/aic7xxx/
Daic7xxx.reg471 * Upper four bits are the device id. The ONEBIT is set when the re/selecting
Daic79xx.reg1865 * Upper four bits are the device id. The ONEBIT is set when the re/selecting
Daic7xxx.seq156 * selecting, keep polling the current channel until
Daic79xx.seq570 * we are selecting with atn regardless of our packetized
/drivers/usb/gadget/
DKconfig112 If selecting USB_GADGET_DEBUG_FILES this value may be set by