1 /* 2 * Disk Array driver for HP Smart Array SAS controllers 3 * Copyright 2000, 2014 Hewlett-Packard Development Company, L.P. 4 * 5 * This program is free software; you can redistribute it and/or modify 6 * it under the terms of the GNU General Public License as published by 7 * the Free Software Foundation; version 2 of the License. 8 * 9 * This program is distributed in the hope that it will be useful, 10 * but WITHOUT ANY WARRANTY; without even the implied warranty of 11 * MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, GOOD TITLE or 12 * NON INFRINGEMENT. See the GNU General Public License for more details. 13 * 14 * You should have received a copy of the GNU General Public License 15 * along with this program; if not, write to the Free Software 16 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 17 * 18 * Questions/Comments/Bugfixes to iss_storagedev@hp.com 19 * 20 */ 21 #ifndef HPSA_CMD_H 22 #define HPSA_CMD_H 23 24 /* general boundary defintions */ 25 #define SENSEINFOBYTES 32 /* may vary between hbas */ 26 #define SG_ENTRIES_IN_CMD 32 /* Max SG entries excluding chain blocks */ 27 #define HPSA_SG_CHAIN 0x80000000 28 #define HPSA_SG_LAST 0x40000000 29 #define MAXREPLYQS 256 30 31 /* Command Status value */ 32 #define CMD_SUCCESS 0x0000 33 #define CMD_TARGET_STATUS 0x0001 34 #define CMD_DATA_UNDERRUN 0x0002 35 #define CMD_DATA_OVERRUN 0x0003 36 #define CMD_INVALID 0x0004 37 #define CMD_PROTOCOL_ERR 0x0005 38 #define CMD_HARDWARE_ERR 0x0006 39 #define CMD_CONNECTION_LOST 0x0007 40 #define CMD_ABORTED 0x0008 41 #define CMD_ABORT_FAILED 0x0009 42 #define CMD_UNSOLICITED_ABORT 0x000A 43 #define CMD_TIMEOUT 0x000B 44 #define CMD_UNABORTABLE 0x000C 45 #define CMD_IOACCEL_DISABLED 0x000E 46 47 48 /* Unit Attentions ASC's as defined for the MSA2012sa */ 49 #define POWER_OR_RESET 0x29 50 #define STATE_CHANGED 0x2a 51 #define UNIT_ATTENTION_CLEARED 0x2f 52 #define LUN_FAILED 0x3e 53 #define REPORT_LUNS_CHANGED 0x3f 54 55 /* Unit Attentions ASCQ's as defined for the MSA2012sa */ 56 57 /* These ASCQ's defined for ASC = POWER_OR_RESET */ 58 #define POWER_ON_RESET 0x00 59 #define POWER_ON_REBOOT 0x01 60 #define SCSI_BUS_RESET 0x02 61 #define MSA_TARGET_RESET 0x03 62 #define CONTROLLER_FAILOVER 0x04 63 #define TRANSCEIVER_SE 0x05 64 #define TRANSCEIVER_LVD 0x06 65 66 /* These ASCQ's defined for ASC = STATE_CHANGED */ 67 #define RESERVATION_PREEMPTED 0x03 68 #define ASYM_ACCESS_CHANGED 0x06 69 #define LUN_CAPACITY_CHANGED 0x09 70 71 /* transfer direction */ 72 #define XFER_NONE 0x00 73 #define XFER_WRITE 0x01 74 #define XFER_READ 0x02 75 #define XFER_RSVD 0x03 76 77 /* task attribute */ 78 #define ATTR_UNTAGGED 0x00 79 #define ATTR_SIMPLE 0x04 80 #define ATTR_HEADOFQUEUE 0x05 81 #define ATTR_ORDERED 0x06 82 #define ATTR_ACA 0x07 83 84 /* cdb type */ 85 #define TYPE_CMD 0x00 86 #define TYPE_MSG 0x01 87 #define TYPE_IOACCEL2_CMD 0x81 /* 0x81 is not used by hardware */ 88 89 /* Message Types */ 90 #define HPSA_TASK_MANAGEMENT 0x00 91 #define HPSA_RESET 0x01 92 #define HPSA_SCAN 0x02 93 #define HPSA_NOOP 0x03 94 95 #define HPSA_CTLR_RESET_TYPE 0x00 96 #define HPSA_BUS_RESET_TYPE 0x01 97 #define HPSA_TARGET_RESET_TYPE 0x03 98 #define HPSA_LUN_RESET_TYPE 0x04 99 #define HPSA_NEXUS_RESET_TYPE 0x05 100 101 /* Task Management Functions */ 102 #define HPSA_TMF_ABORT_TASK 0x00 103 #define HPSA_TMF_ABORT_TASK_SET 0x01 104 #define HPSA_TMF_CLEAR_ACA 0x02 105 #define HPSA_TMF_CLEAR_TASK_SET 0x03 106 #define HPSA_TMF_QUERY_TASK 0x04 107 #define HPSA_TMF_QUERY_TASK_SET 0x05 108 #define HPSA_TMF_QUERY_ASYNCEVENT 0x06 109 110 111 112 /* config space register offsets */ 113 #define CFG_VENDORID 0x00 114 #define CFG_DEVICEID 0x02 115 #define CFG_I2OBAR 0x10 116 #define CFG_MEM1BAR 0x14 117 118 /* i2o space register offsets */ 119 #define I2O_IBDB_SET 0x20 120 #define I2O_IBDB_CLEAR 0x70 121 #define I2O_INT_STATUS 0x30 122 #define I2O_INT_MASK 0x34 123 #define I2O_IBPOST_Q 0x40 124 #define I2O_OBPOST_Q 0x44 125 #define I2O_DMA1_CFG 0x214 126 127 /* Configuration Table */ 128 #define CFGTBL_ChangeReq 0x00000001l 129 #define CFGTBL_AccCmds 0x00000001l 130 #define DOORBELL_CTLR_RESET 0x00000004l 131 #define DOORBELL_CTLR_RESET2 0x00000020l 132 #define DOORBELL_CLEAR_EVENTS 0x00000040l 133 134 #define CFGTBL_Trans_Simple 0x00000002l 135 #define CFGTBL_Trans_Performant 0x00000004l 136 #define CFGTBL_Trans_io_accel1 0x00000080l 137 #define CFGTBL_Trans_io_accel2 0x00000100l 138 #define CFGTBL_Trans_use_short_tags 0x20000000l 139 #define CFGTBL_Trans_enable_directed_msix (1 << 30) 140 141 #define CFGTBL_BusType_Ultra2 0x00000001l 142 #define CFGTBL_BusType_Ultra3 0x00000002l 143 #define CFGTBL_BusType_Fibre1G 0x00000100l 144 #define CFGTBL_BusType_Fibre2G 0x00000200l 145 146 /* VPD Inquiry types */ 147 #define HPSA_VPD_SUPPORTED_PAGES 0x00 148 #define HPSA_VPD_LV_DEVICE_GEOMETRY 0xC1 149 #define HPSA_VPD_LV_IOACCEL_STATUS 0xC2 150 #define HPSA_VPD_LV_STATUS 0xC3 151 #define HPSA_VPD_HEADER_SZ 4 152 153 /* Logical volume states */ 154 #define HPSA_VPD_LV_STATUS_UNSUPPORTED 0xff 155 #define HPSA_LV_OK 0x0 156 #define HPSA_LV_UNDERGOING_ERASE 0x0F 157 #define HPSA_LV_UNDERGOING_RPI 0x12 158 #define HPSA_LV_PENDING_RPI 0x13 159 #define HPSA_LV_ENCRYPTED_NO_KEY 0x14 160 #define HPSA_LV_PLAINTEXT_IN_ENCRYPT_ONLY_CONTROLLER 0x15 161 #define HPSA_LV_UNDERGOING_ENCRYPTION 0x16 162 #define HPSA_LV_UNDERGOING_ENCRYPTION_REKEYING 0x17 163 #define HPSA_LV_ENCRYPTED_IN_NON_ENCRYPTED_CONTROLLER 0x18 164 #define HPSA_LV_PENDING_ENCRYPTION 0x19 165 #define HPSA_LV_PENDING_ENCRYPTION_REKEYING 0x1A 166 167 struct vals32 { 168 u32 lower; 169 u32 upper; 170 }; 171 172 union u64bit { 173 struct vals32 val32; 174 u64 val; 175 }; 176 177 /* FIXME this is a per controller value (barf!) */ 178 #define HPSA_MAX_LUN 1024 179 #define HPSA_MAX_PHYS_LUN 1024 180 #define MAX_EXT_TARGETS 32 181 #define HPSA_MAX_DEVICES (HPSA_MAX_PHYS_LUN + HPSA_MAX_LUN + \ 182 MAX_EXT_TARGETS + 1) /* + 1 is for the controller itself */ 183 184 /* SCSI-3 Commands */ 185 #pragma pack(1) 186 187 #define HPSA_INQUIRY 0x12 188 struct InquiryData { 189 u8 data_byte[36]; 190 }; 191 192 #define HPSA_REPORT_LOG 0xc2 /* Report Logical LUNs */ 193 #define HPSA_REPORT_PHYS 0xc3 /* Report Physical LUNs */ 194 #define HPSA_REPORT_PHYS_EXTENDED 0x02 195 #define HPSA_CISS_READ 0xc0 /* CISS Read */ 196 #define HPSA_GET_RAID_MAP 0xc8 /* CISS Get RAID Layout Map */ 197 198 #define RAID_MAP_MAX_ENTRIES 256 199 200 struct raid_map_disk_data { 201 u32 ioaccel_handle; /**< Handle to access this disk via the 202 * I/O accelerator */ 203 u8 xor_mult[2]; /**< XOR multipliers for this position, 204 * valid for data disks only */ 205 u8 reserved[2]; 206 }; 207 208 struct raid_map_data { 209 u32 structure_size; /* Size of entire structure in bytes */ 210 u32 volume_blk_size; /* bytes / block in the volume */ 211 u64 volume_blk_cnt; /* logical blocks on the volume */ 212 u8 phys_blk_shift; /* Shift factor to convert between 213 * units of logical blocks and physical 214 * disk blocks */ 215 u8 parity_rotation_shift; /* Shift factor to convert between units 216 * of logical stripes and physical 217 * stripes */ 218 u16 strip_size; /* blocks used on each disk / stripe */ 219 u64 disk_starting_blk; /* First disk block used in volume */ 220 u64 disk_blk_cnt; /* disk blocks used by volume / disk */ 221 u16 data_disks_per_row; /* data disk entries / row in the map */ 222 u16 metadata_disks_per_row; /* mirror/parity disk entries / row 223 * in the map */ 224 u16 row_cnt; /* rows in each layout map */ 225 u16 layout_map_count; /* layout maps (1 map per mirror/parity 226 * group) */ 227 u16 flags; /* Bit 0 set if encryption enabled */ 228 #define RAID_MAP_FLAG_ENCRYPT_ON 0x01 229 u16 dekindex; /* Data encryption key index. */ 230 u8 reserved[16]; 231 struct raid_map_disk_data data[RAID_MAP_MAX_ENTRIES]; 232 }; 233 234 struct ReportLUNdata { 235 u8 LUNListLength[4]; 236 u8 extended_response_flag; 237 u8 reserved[3]; 238 u8 LUN[HPSA_MAX_LUN][8]; 239 }; 240 241 struct ext_report_lun_entry { 242 u8 lunid[8]; 243 u8 wwid[8]; 244 u8 device_type; 245 u8 device_flags; 246 u8 lun_count; /* multi-lun device, how many luns */ 247 u8 redundant_paths; 248 u32 ioaccel_handle; /* ioaccel1 only uses lower 16 bits */ 249 }; 250 251 struct ReportExtendedLUNdata { 252 u8 LUNListLength[4]; 253 u8 extended_response_flag; 254 u8 reserved[3]; 255 struct ext_report_lun_entry LUN[HPSA_MAX_LUN]; 256 }; 257 258 struct SenseSubsystem_info { 259 u8 reserved[36]; 260 u8 portname[8]; 261 u8 reserved1[1108]; 262 }; 263 264 /* BMIC commands */ 265 #define BMIC_READ 0x26 266 #define BMIC_WRITE 0x27 267 #define BMIC_CACHE_FLUSH 0xc2 268 #define HPSA_CACHE_FLUSH 0x01 /* C2 was already being used by HPSA */ 269 #define BMIC_FLASH_FIRMWARE 0xF7 270 #define BMIC_SENSE_CONTROLLER_PARAMETERS 0x64 271 272 /* Command List Structure */ 273 union SCSI3Addr { 274 struct { 275 u8 Dev; 276 u8 Bus:6; 277 u8 Mode:2; /* b00 */ 278 } PeripDev; 279 struct { 280 u8 DevLSB; 281 u8 DevMSB:6; 282 u8 Mode:2; /* b01 */ 283 } LogDev; 284 struct { 285 u8 Dev:5; 286 u8 Bus:3; 287 u8 Targ:6; 288 u8 Mode:2; /* b10 */ 289 } LogUnit; 290 }; 291 292 struct PhysDevAddr { 293 u32 TargetId:24; 294 u32 Bus:6; 295 u32 Mode:2; 296 /* 2 level target device addr */ 297 union SCSI3Addr Target[2]; 298 }; 299 300 struct LogDevAddr { 301 u32 VolId:30; 302 u32 Mode:2; 303 u8 reserved[4]; 304 }; 305 306 union LUNAddr { 307 u8 LunAddrBytes[8]; 308 union SCSI3Addr SCSI3Lun[4]; 309 struct PhysDevAddr PhysDev; 310 struct LogDevAddr LogDev; 311 }; 312 313 struct CommandListHeader { 314 u8 ReplyQueue; 315 u8 SGList; 316 u16 SGTotal; 317 struct vals32 Tag; 318 union LUNAddr LUN; 319 }; 320 321 struct RequestBlock { 322 u8 CDBLen; 323 struct { 324 u8 Type:3; 325 u8 Attribute:3; 326 u8 Direction:2; 327 } Type; 328 u16 Timeout; 329 u8 CDB[16]; 330 }; 331 332 struct ErrDescriptor { 333 struct vals32 Addr; 334 u32 Len; 335 }; 336 337 struct SGDescriptor { 338 struct vals32 Addr; 339 u32 Len; 340 u32 Ext; 341 }; 342 343 union MoreErrInfo { 344 struct { 345 u8 Reserved[3]; 346 u8 Type; 347 u32 ErrorInfo; 348 } Common_Info; 349 struct { 350 u8 Reserved[2]; 351 u8 offense_size; /* size of offending entry */ 352 u8 offense_num; /* byte # of offense 0-base */ 353 u32 offense_value; 354 } Invalid_Cmd; 355 }; 356 struct ErrorInfo { 357 u8 ScsiStatus; 358 u8 SenseLen; 359 u16 CommandStatus; 360 u32 ResidualCnt; 361 union MoreErrInfo MoreErrInfo; 362 u8 SenseInfo[SENSEINFOBYTES]; 363 }; 364 /* Command types */ 365 #define CMD_IOCTL_PEND 0x01 366 #define CMD_SCSI 0x03 367 #define CMD_IOACCEL1 0x04 368 #define CMD_IOACCEL2 0x05 369 370 #define DIRECT_LOOKUP_SHIFT 5 371 #define DIRECT_LOOKUP_BIT 0x10 372 #define DIRECT_LOOKUP_MASK (~((1 << DIRECT_LOOKUP_SHIFT) - 1)) 373 374 #define HPSA_ERROR_BIT 0x02 375 struct ctlr_info; /* defined in hpsa.h */ 376 /* The size of this structure needs to be divisible by 32 377 * on all architectures because low 5 bits of the addresses 378 * are used as follows: 379 * 380 * bit 0: to device, used to indicate "performant mode" command 381 * from device, indidcates error status. 382 * bit 1-3: to device, indicates block fetch table entry for 383 * reducing DMA in fetching commands from host memory. 384 * bit 4: used to indicate whether tag is "direct lookup" (index), 385 * or a bus address. 386 */ 387 388 #define COMMANDLIST_ALIGNMENT 128 389 struct CommandList { 390 struct CommandListHeader Header; 391 struct RequestBlock Request; 392 struct ErrDescriptor ErrDesc; 393 struct SGDescriptor SG[SG_ENTRIES_IN_CMD]; 394 /* information associated with the command */ 395 u32 busaddr; /* physical addr of this record */ 396 struct ErrorInfo *err_info; /* pointer to the allocated mem */ 397 struct ctlr_info *h; 398 int cmd_type; 399 long cmdindex; 400 struct list_head list; 401 struct completion *waiting; 402 void *scsi_cmd; 403 } __aligned(COMMANDLIST_ALIGNMENT); 404 405 /* Max S/G elements in I/O accelerator command */ 406 #define IOACCEL1_MAXSGENTRIES 24 407 #define IOACCEL2_MAXSGENTRIES 28 408 409 /* 410 * Structure for I/O accelerator (mode 1) commands. 411 * Note that this structure must be 128-byte aligned in size. 412 */ 413 #define IOACCEL1_COMMANDLIST_ALIGNMENT 128 414 struct io_accel1_cmd { 415 u16 dev_handle; /* 0x00 - 0x01 */ 416 u8 reserved1; /* 0x02 */ 417 u8 function; /* 0x03 */ 418 u8 reserved2[8]; /* 0x04 - 0x0B */ 419 u32 err_info; /* 0x0C - 0x0F */ 420 u8 reserved3[2]; /* 0x10 - 0x11 */ 421 u8 err_info_len; /* 0x12 */ 422 u8 reserved4; /* 0x13 */ 423 u8 sgl_offset; /* 0x14 */ 424 u8 reserved5[7]; /* 0x15 - 0x1B */ 425 u32 transfer_len; /* 0x1C - 0x1F */ 426 u8 reserved6[4]; /* 0x20 - 0x23 */ 427 u16 io_flags; /* 0x24 - 0x25 */ 428 u8 reserved7[14]; /* 0x26 - 0x33 */ 429 u8 LUN[8]; /* 0x34 - 0x3B */ 430 u32 control; /* 0x3C - 0x3F */ 431 u8 CDB[16]; /* 0x40 - 0x4F */ 432 u8 reserved8[16]; /* 0x50 - 0x5F */ 433 u16 host_context_flags; /* 0x60 - 0x61 */ 434 u16 timeout_sec; /* 0x62 - 0x63 */ 435 u8 ReplyQueue; /* 0x64 */ 436 u8 reserved9[3]; /* 0x65 - 0x67 */ 437 struct vals32 Tag; /* 0x68 - 0x6F */ 438 struct vals32 host_addr; /* 0x70 - 0x77 */ 439 u8 CISS_LUN[8]; /* 0x78 - 0x7F */ 440 struct SGDescriptor SG[IOACCEL1_MAXSGENTRIES]; 441 } __aligned(IOACCEL1_COMMANDLIST_ALIGNMENT); 442 443 #define IOACCEL1_FUNCTION_SCSIIO 0x00 444 #define IOACCEL1_SGLOFFSET 32 445 446 #define IOACCEL1_IOFLAGS_IO_REQ 0x4000 447 #define IOACCEL1_IOFLAGS_CDBLEN_MASK 0x001F 448 #define IOACCEL1_IOFLAGS_CDBLEN_MAX 16 449 450 #define IOACCEL1_CONTROL_NODATAXFER 0x00000000 451 #define IOACCEL1_CONTROL_DATA_OUT 0x01000000 452 #define IOACCEL1_CONTROL_DATA_IN 0x02000000 453 #define IOACCEL1_CONTROL_TASKPRIO_MASK 0x00007800 454 #define IOACCEL1_CONTROL_TASKPRIO_SHIFT 11 455 #define IOACCEL1_CONTROL_SIMPLEQUEUE 0x00000000 456 #define IOACCEL1_CONTROL_HEADOFQUEUE 0x00000100 457 #define IOACCEL1_CONTROL_ORDEREDQUEUE 0x00000200 458 #define IOACCEL1_CONTROL_ACA 0x00000400 459 460 #define IOACCEL1_HCFLAGS_CISS_FORMAT 0x0013 461 462 #define IOACCEL1_BUSADDR_CMDTYPE 0x00000060 463 464 struct ioaccel2_sg_element { 465 u64 address; 466 u32 length; 467 u8 reserved[3]; 468 u8 chain_indicator; 469 #define IOACCEL2_CHAIN 0x80 470 }; 471 472 /* 473 * SCSI Response Format structure for IO Accelerator Mode 2 474 */ 475 struct io_accel2_scsi_response { 476 u8 IU_type; 477 #define IOACCEL2_IU_TYPE_SRF 0x60 478 u8 reserved1[3]; 479 u8 req_id[4]; /* request identifier */ 480 u8 reserved2[4]; 481 u8 serv_response; /* service response */ 482 #define IOACCEL2_SERV_RESPONSE_COMPLETE 0x000 483 #define IOACCEL2_SERV_RESPONSE_FAILURE 0x001 484 #define IOACCEL2_SERV_RESPONSE_TMF_COMPLETE 0x002 485 #define IOACCEL2_SERV_RESPONSE_TMF_SUCCESS 0x003 486 #define IOACCEL2_SERV_RESPONSE_TMF_REJECTED 0x004 487 #define IOACCEL2_SERV_RESPONSE_TMF_WRONG_LUN 0x005 488 u8 status; /* status */ 489 #define IOACCEL2_STATUS_SR_TASK_COMP_GOOD 0x00 490 #define IOACCEL2_STATUS_SR_TASK_COMP_CHK_COND 0x02 491 #define IOACCEL2_STATUS_SR_TASK_COMP_BUSY 0x08 492 #define IOACCEL2_STATUS_SR_TASK_COMP_RES_CON 0x18 493 #define IOACCEL2_STATUS_SR_TASK_COMP_SET_FULL 0x28 494 #define IOACCEL2_STATUS_SR_TASK_COMP_ABORTED 0x40 495 #define IOACCEL2_STATUS_SR_IOACCEL_DISABLED 0x0E 496 u8 data_present; /* low 2 bits */ 497 #define IOACCEL2_NO_DATAPRESENT 0x000 498 #define IOACCEL2_RESPONSE_DATAPRESENT 0x001 499 #define IOACCEL2_SENSE_DATA_PRESENT 0x002 500 #define IOACCEL2_RESERVED 0x003 501 u8 sense_data_len; /* sense/response data length */ 502 u8 resid_cnt[4]; /* residual count */ 503 u8 sense_data_buff[32]; /* sense/response data buffer */ 504 }; 505 506 /* 507 * Structure for I/O accelerator (mode 2 or m2) commands. 508 * Note that this structure must be 128-byte aligned in size. 509 */ 510 #define IOACCEL2_COMMANDLIST_ALIGNMENT 128 511 struct io_accel2_cmd { 512 u8 IU_type; /* IU Type */ 513 u8 direction; /* direction, memtype, and encryption */ 514 #define IOACCEL2_DIRECTION_MASK 0x03 /* bits 0,1: direction */ 515 #define IOACCEL2_DIRECTION_MEMTYPE_MASK 0x04 /* bit 2: memtype source/dest */ 516 /* 0b=PCIe, 1b=DDR */ 517 #define IOACCEL2_DIRECTION_ENCRYPT_MASK 0x08 /* bit 3: encryption flag */ 518 /* 0=off, 1=on */ 519 u8 reply_queue; /* Reply Queue ID */ 520 u8 reserved1; /* Reserved */ 521 u32 scsi_nexus; /* Device Handle */ 522 u32 Tag; /* cciss tag, lower 4 bytes only */ 523 u32 tweak_lower; /* Encryption tweak, lower 4 bytes */ 524 u8 cdb[16]; /* SCSI Command Descriptor Block */ 525 u8 cciss_lun[8]; /* 8 byte SCSI address */ 526 u32 data_len; /* Total bytes to transfer */ 527 u8 cmd_priority_task_attr; /* priority and task attrs */ 528 #define IOACCEL2_PRIORITY_MASK 0x78 529 #define IOACCEL2_ATTR_MASK 0x07 530 u8 sg_count; /* Number of sg elements */ 531 u16 dekindex; /* Data encryption key index */ 532 u64 err_ptr; /* Error Pointer */ 533 u32 err_len; /* Error Length*/ 534 u32 tweak_upper; /* Encryption tweak, upper 4 bytes */ 535 struct ioaccel2_sg_element sg[IOACCEL2_MAXSGENTRIES]; 536 struct io_accel2_scsi_response error_data; 537 } __aligned(IOACCEL2_COMMANDLIST_ALIGNMENT); 538 539 /* 540 * defines for Mode 2 command struct 541 * FIXME: this can't be all I need mfm 542 */ 543 #define IOACCEL2_IU_TYPE 0x40 544 #define IOACCEL2_IU_TMF_TYPE 0x41 545 #define IOACCEL2_DIR_NO_DATA 0x00 546 #define IOACCEL2_DIR_DATA_IN 0x01 547 #define IOACCEL2_DIR_DATA_OUT 0x02 548 /* 549 * SCSI Task Management Request format for Accelerator Mode 2 550 */ 551 struct hpsa_tmf_struct { 552 u8 iu_type; /* Information Unit Type */ 553 u8 reply_queue; /* Reply Queue ID */ 554 u8 tmf; /* Task Management Function */ 555 u8 reserved1; /* byte 3 Reserved */ 556 u32 it_nexus; /* SCSI I-T Nexus */ 557 u8 lun_id[8]; /* LUN ID for TMF request */ 558 struct vals32 Tag; /* cciss tag associated w/ request */ 559 struct vals32 abort_tag;/* cciss tag of SCSI cmd or task to abort */ 560 u64 error_ptr; /* Error Pointer */ 561 u32 error_len; /* Error Length */ 562 }; 563 564 /* Configuration Table Structure */ 565 struct HostWrite { 566 u32 TransportRequest; 567 u32 command_pool_addr_hi; 568 u32 CoalIntDelay; 569 u32 CoalIntCount; 570 }; 571 572 #define SIMPLE_MODE 0x02 573 #define PERFORMANT_MODE 0x04 574 #define MEMQ_MODE 0x08 575 #define IOACCEL_MODE_1 0x80 576 577 #define DRIVER_SUPPORT_UA_ENABLE 0x00000001 578 579 struct CfgTable { 580 u8 Signature[4]; 581 u32 SpecValence; 582 u32 TransportSupport; 583 u32 TransportActive; 584 struct HostWrite HostWrite; 585 u32 CmdsOutMax; 586 u32 BusTypes; 587 u32 TransMethodOffset; 588 u8 ServerName[16]; 589 u32 HeartBeat; 590 u32 driver_support; 591 #define ENABLE_SCSI_PREFETCH 0x100 592 #define ENABLE_UNIT_ATTN 0x01 593 u32 MaxScatterGatherElements; 594 u32 MaxLogicalUnits; 595 u32 MaxPhysicalDevices; 596 u32 MaxPhysicalDrivesPerLogicalUnit; 597 u32 MaxPerformantModeCommands; 598 u32 MaxBlockFetch; 599 u32 PowerConservationSupport; 600 u32 PowerConservationEnable; 601 u32 TMFSupportFlags; 602 u8 TMFTagMask[8]; 603 u8 reserved[0x78 - 0x70]; 604 u32 misc_fw_support; /* offset 0x78 */ 605 #define MISC_FW_DOORBELL_RESET (0x02) 606 #define MISC_FW_DOORBELL_RESET2 (0x010) 607 #define MISC_FW_RAID_OFFLOAD_BASIC (0x020) 608 #define MISC_FW_EVENT_NOTIFY (0x080) 609 u8 driver_version[32]; 610 u32 max_cached_write_size; 611 u8 driver_scratchpad[16]; 612 u32 max_error_info_length; 613 u32 io_accel_max_embedded_sg_count; 614 u32 io_accel_request_size_offset; 615 u32 event_notify; 616 #define HPSA_EVENT_NOTIFY_ACCEL_IO_PATH_STATE_CHANGE (1 << 30) 617 #define HPSA_EVENT_NOTIFY_ACCEL_IO_PATH_CONFIG_CHANGE (1 << 31) 618 u32 clear_event_notify; 619 }; 620 621 #define NUM_BLOCKFETCH_ENTRIES 8 622 struct TransTable_struct { 623 u32 BlockFetch[NUM_BLOCKFETCH_ENTRIES]; 624 u32 RepQSize; 625 u32 RepQCount; 626 u32 RepQCtrAddrLow32; 627 u32 RepQCtrAddrHigh32; 628 #define MAX_REPLY_QUEUES 64 629 struct vals32 RepQAddr[MAX_REPLY_QUEUES]; 630 }; 631 632 struct hpsa_pci_info { 633 unsigned char bus; 634 unsigned char dev_fn; 635 unsigned short domain; 636 u32 board_id; 637 }; 638 639 #pragma pack() 640 #endif /* HPSA_CMD_H */ 641