Home
last modified time | relevance | path

Searched refs:USB (Results 1 – 25 of 134) sorted by relevance

123456

/arch/arm/boot/dts/
Dusb_a9g20.dts2 * usb_a9g20.dts - Device Tree file for Caloa USB A9G20 board
12 model = "Calao USB A9G20";
Domap3-cm-t3x.dtsi23 /* HS USB Port 1 Power */
32 /* HS USB Port 2 Power */
41 /* HS USB Host PHY on PORT 1 */
47 /* HS USB Host PHY on PORT 2 */
Dusb_a9260.dts2 * usb_a9260.dts - Device Tree file for Caloa USB A9260 board
13 model = "Calao USB A9260";
Dusb_a9g20_lpw.dts2 * usb_a9g20_lpw.dts - Device Tree file for Caloa USB A9G20 Low Power board
12 model = "Calao USB A9G20 Low Power";
Dkirkwood-ts219-6281.dts19 pmx_USB_copy_button: pmx-USB-copy-button {
43 label = "USB Copy";
Dkirkwood-ts219-6282.dts33 pmx_USB_copy_button: pmx-USB-copy-button {
53 label = "USB Copy";
Dorion5x-rd88f5182-nas.dts136 * MPP[22] USB 0 over current indication
137 * MPP[23] USB 1 over current indication
138 * MPP[24] USB 1 over current enable
139 * MPP[25] USB 0 over current enable
Dkirkwood-ts419.dtsi20 pmx_USB_copy_button: pmx-USB-copy-button {
49 label = "USB Copy";
Dkirkwood-laplug.dts101 regulator-name = "USB Power Back 1";
113 regulator-name = "USB Power Back 2";
125 regulator-name = "USB Power Front";
Dusb_a9g20_common.dtsi2 * usb_a9g20.dts - Device Tree file for Caloa USB A9G20 board
Domap3-beagle-xm-ab.dts12 /* HS USB Port 2 Power enable was inverted with the xM C */
Dusb_a9263.dts2 * usb_a9263.dts - Device Tree file for Caloa USB A9293 board
12 model = "Calao USB A9263";
Domap3-sbc-t3730.dts19 OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
Dimx6q-gk802.dts147 /* External USB-A port (USBOTG) */
153 /* Internal USB port (USBH1), connected to RTL8192CU */
Domap3-sbc-t3530.dts19 OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
/arch/arm/mach-cns3xxx/
DKconfig17 for USB, USB-OTG, MMC/SD/SDIO, SATA, PCI-E, etc.
/arch/sh/kernel/cpu/sh3/
Dsetup-sh7705.c28 DMAC, SCIF0, SCIF2, ADC_ADI, USB, enumerator
46 INTC_VECT(USB, 0xa20), INTC_VECT(USB, 0xa40),
63 { 0xa4080000, 0, 16, 4, /* IPRF */ { 0, 0, USB } },
/arch/avr32/boards/hammerhead/
DKconfig6 bool "Philips ISP116x-hcd USB support"
8 This enables USB support for Hammerheads internal ISP116x
11 Choose 'Y' here if you want to have your board USB driven.
/arch/powerpc/platforms/embedded6xx/
DKconfig92 bool "USB Gecko udbg console for the Nintendo GameCube/Wii"
96 USB Gecko adapter as an udbg console.
97 The USB Gecko is a EXI to USB Serial converter that can be plugged
/arch/sh/kernel/cpu/sh4a/
Dsetup-sh7366.c262 MFI, VPU, USB, enumerator
288 INTC_VECT(MFI, 0x900), INTC_VECT(VPU, 0x980), INTC_VECT(USB, 0xa20),
340 { 0, 0, 0, CMT, 0, USB, } },
355 { 0xa4080014, 0, 16, 4, /* IPRF */ { 0, DMAC45, USB, CMT } },
/arch/sh/kernel/cpu/sh4/
Dsetup-sh7760.c29 USB, LCDC, enumerator
58 INTC_VECT(USB, 0xa00), INTC_VECT(LCDC, 0xa20),
92 SSI0, SSI1, HAC0, HAC1, I2C0, I2C1, USB, LCDC,
113 { 0xfe080008, 0, 32, 4, /* INTPRI08 */ { USB, LCDC, DMABRG, SCIF0,
/arch/powerpc/sysdev/qe_lib/
DKconfig27 QE USB Controller support
/arch/sh/drivers/dma/
DKconfig46 The DMABRG does data transfers from main memory to Audio/USB units
48 Say Y if you want to use Audio/USB DMA on your SH7760 board.
/arch/blackfin/mach-bf548/
DKconfig327 int "IRQ USB INT0"
330 int "IRQ USB INT1"
333 int "IRQ USB INT2"
336 int "IRQ USB DMA"
/arch/arm/mach-mmp/
Dclock-pxa910.c46 static APMU_CLK(u2o, USB, 0x1b, 480000000);

123456