Searched refs:ata (Results 1 – 12 of 12) sorted by relevance
| /drivers/usb/storage/ |
| D | isd200.c | 489 union ata_cdb ata; in isd200_action() local
496 memset(&ata, 0, sizeof(ata)); in isd200_action()
500 ata.generic.SignatureByte0 = info->ConfigData.ATAMajorCommand; in isd200_action()
501 ata.generic.SignatureByte1 = info->ConfigData.ATAMinorCommand; in isd200_action()
502 ata.generic.TransferBlockSize = 1; in isd200_action()
507 ata.generic.ActionSelect = ACTION_SELECT_0|ACTION_SELECT_2; in isd200_action()
508 ata.generic.RegisterSelect = in isd200_action()
516 ata.generic.ActionSelect = ACTION_SELECT_1|ACTION_SELECT_2| in isd200_action()
519 ata.generic.RegisterSelect = REG_DEVICE_HEAD; in isd200_action()
520 ata.write.DeviceHeadByte = value; in isd200_action()
[all …]
|
| D | Kconfig | 179 Say Y here if you want to use SAT (ata pass through) on devices based
|
| /drivers/ata/ |
| D | pata_at32.c | 93 const struct ata_timing *ata) in pata_at32_setup_timing() argument
104 timing.read_cycle = ata->cyc8b; in pata_at32_setup_timing()
107 timing.nrd_setup = ata->setup; in pata_at32_setup_timing()
108 timing.nrd_pulse = ata->act8b; in pata_at32_setup_timing()
109 timing.nrd_recover = ata->rec8b; in pata_at32_setup_timing()
137 ata->cyc8b, ata->setup, ata->act8b, ata->rec8b); in pata_at32_setup_timing()
|
| D | pata_at91.c | 205 struct at91_ide_info *info, const struct ata_timing *ata) in set_smc_timing() argument
218 t6z = (ata->mode < XFER_PIO_5) ? 30 : 20; in set_smc_timing()
220 cycle = calc_mck_cycles(ata->cyc8b, mck_hz); in set_smc_timing()
221 setup = calc_mck_cycles(ata->setup, mck_hz); in set_smc_timing()
222 pulse = calc_mck_cycles(ata->act8b, mck_hz); in set_smc_timing()
|
| D | pata_samsung_cf.c | 93 pata_s3c_setup_timing(struct s3c_ide_info *info, const struct ata_timing *ata) in pata_s3c_setup_timing() argument
95 int t1 = ata->setup; in pata_s3c_setup_timing()
96 int t2 = ata->act8b; in pata_s3c_setup_timing()
97 int t2i = ata->rec8b; in pata_s3c_setup_timing()
|
| D | sata_sil24.c | 267 struct sil24_ata_block ata; member
610 struct sil24_prb *prb = &pp->cmd_block[0].ata.prb; in sil24_exec_polled_cmd()
854 prb = &cb->ata.prb; in sil24_qc_prep()
855 sge = cb->ata.sge; in sil24_qc_prep()
|
| /drivers/dma/bestcomm/ |
| D | Makefile | 6 bestcomm-ata-objs := ata.o bcom_ata_task.o
11 obj-$(CONFIG_PPC_BESTCOMM_ATA) += bestcomm-ata.o
|
| /drivers/ |
| D | Makefile | 69 obj-$(CONFIG_ATA) += ata/
|
| D | Kconfig | 27 source "drivers/ata/Kconfig"
|
| /drivers/scsi/ |
| D | eata.c | 627 ata : 1, member
643 ata : 1, /* This is an ATA device */ member
1170 if (!info.haaval || info.ata) { in port_detect()
1173 name, port_base, bus_type, info.haaval, info.ata); in port_detect()
|
| /drivers/firmware/ |
| D | edd.c | 201 info->params.device_path.ata.device); in edd_show_interface()
|
| /drivers/pinctrl/ |
| D | pinctrl-tegra20.c | 2051 MUX_PG(ata, IDE, NAND, GMI, RSVD4, 0x14, 0, 0x80, 24, 0xa0, 0),
|