• Home
  • Line#
  • Scopes#
  • Navigate#
  • Raw
  • Download
1 /*
2  * Copyright © 2010 Intel Corporation
3  *
4  * Permission is hereby granted, free of charge, to any person obtaining a
5  * copy of this software and associated documentation files (the "Software"),
6  * to deal in the Software without restriction, including without limitation
7  * the rights to use, copy, modify, merge, publish, distribute, sublicense,
8  * and/or sell copies of the Software, and to permit persons to whom the
9  * Software is furnished to do so, subject to the following conditions:
10  *
11  * The above copyright notice and this permission notice (including the next
12  * paragraph) shall be included in all copies or substantial portions of the
13  * Software.
14  *
15  * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
16  * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
17  * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
18  * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
19  * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
20  * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
21  * DEALINGS IN THE SOFTWARE.
22  *
23  * Authors:
24  * jim liu <jim.liu@intel.com>
25  * Jackie Li<yaodong.li@intel.com>
26  */
27 
28 #include "mdfld_dsi_dpi.h"
29 #include "mdfld_output.h"
30 #include "mdfld_dsi_pkg_sender.h"
31 #include "psb_drv.h"
32 #include "tc35876x-dsi-lvds.h"
33 
34 static void mdfld_dsi_dpi_shut_down(struct mdfld_dsi_dpi_output *output,
35 								int pipe);
36 
mdfld_wait_for_HS_DATA_FIFO(struct drm_device * dev,u32 pipe)37 static void mdfld_wait_for_HS_DATA_FIFO(struct drm_device *dev, u32 pipe)
38 {
39 	u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
40 	int timeout = 0;
41 
42 	udelay(500);
43 
44 	/* This will time out after approximately 2+ seconds */
45 	while ((timeout < 20000) &&
46 		(REG_READ(gen_fifo_stat_reg) & DSI_FIFO_GEN_HS_DATA_FULL)) {
47 		udelay(100);
48 		timeout++;
49 	}
50 
51 	if (timeout == 20000)
52 		DRM_INFO("MIPI: HS Data FIFO was never cleared!\n");
53 }
54 
mdfld_wait_for_HS_CTRL_FIFO(struct drm_device * dev,u32 pipe)55 static void mdfld_wait_for_HS_CTRL_FIFO(struct drm_device *dev, u32 pipe)
56 {
57 	u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
58 	int timeout = 0;
59 
60 	udelay(500);
61 
62 	/* This will time out after approximately 2+ seconds */
63 	while ((timeout < 20000) && (REG_READ(gen_fifo_stat_reg)
64 					& DSI_FIFO_GEN_HS_CTRL_FULL)) {
65 		udelay(100);
66 		timeout++;
67 	}
68 	if (timeout == 20000)
69 		DRM_INFO("MIPI: HS CMD FIFO was never cleared!\n");
70 }
71 
mdfld_wait_for_DPI_CTRL_FIFO(struct drm_device * dev,u32 pipe)72 static void mdfld_wait_for_DPI_CTRL_FIFO(struct drm_device *dev, u32 pipe)
73 {
74 	u32 gen_fifo_stat_reg = MIPI_GEN_FIFO_STAT_REG(pipe);
75 	int timeout = 0;
76 
77 	udelay(500);
78 
79 	/* This will time out after approximately 2+ seconds */
80 	while ((timeout < 20000) && ((REG_READ(gen_fifo_stat_reg) &
81 					DPI_FIFO_EMPTY) != DPI_FIFO_EMPTY)) {
82 		udelay(100);
83 		timeout++;
84 	}
85 
86 	if (timeout == 20000)
87 		DRM_ERROR("MIPI: DPI FIFO was never cleared\n");
88 }
89 
mdfld_wait_for_SPL_PKG_SENT(struct drm_device * dev,u32 pipe)90 static void mdfld_wait_for_SPL_PKG_SENT(struct drm_device *dev, u32 pipe)
91 {
92 	u32 intr_stat_reg = MIPI_INTR_STAT_REG(pipe);
93 	int timeout = 0;
94 
95 	udelay(500);
96 
97 	/* This will time out after approximately 2+ seconds */
98 	while ((timeout < 20000) && (!(REG_READ(intr_stat_reg)
99 					& DSI_INTR_STATE_SPL_PKG_SENT))) {
100 		udelay(100);
101 		timeout++;
102 	}
103 
104 	if (timeout == 20000)
105                 DRM_ERROR("MIPI: SPL_PKT_SENT_INTERRUPT was not sent successfully!\n");
106 }
107 
108 /* For TC35876X */
109 
dsi_set_device_ready_state(struct drm_device * dev,int state,int pipe)110 static void dsi_set_device_ready_state(struct drm_device *dev, int state,
111 				int pipe)
112 {
113 	REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), !!state, 0, 0);
114 }
115 
dsi_set_pipe_plane_enable_state(struct drm_device * dev,int state,int pipe)116 static void dsi_set_pipe_plane_enable_state(struct drm_device *dev,
117 							int state, int pipe)
118 {
119 	struct drm_psb_private *dev_priv = dev->dev_private;
120 	u32 pipeconf_reg = PIPEACONF;
121 	u32 dspcntr_reg = DSPACNTR;
122 
123 	u32 dspcntr = dev_priv->dspcntr[pipe];
124 	u32 mipi = MIPI_PORT_EN | PASS_FROM_SPHY_TO_AFE | SEL_FLOPPED_HSTX;
125 
126 	if (pipe) {
127 		pipeconf_reg = PIPECCONF;
128 		dspcntr_reg = DSPCCNTR;
129 	} else
130 		mipi &= (~0x03);
131 
132 	if (state) {
133 		/*Set up pipe */
134 		REG_WRITE(pipeconf_reg, BIT(31));
135 
136 		if (REG_BIT_WAIT(pipeconf_reg, 1, 30))
137 			dev_err(&dev->pdev->dev, "%s: Pipe enable timeout\n",
138 				__func__);
139 
140 		/*Set up display plane */
141 		REG_WRITE(dspcntr_reg, dspcntr);
142 	} else {
143 		u32 dspbase_reg = pipe ? MDFLD_DSPCBASE : MRST_DSPABASE;
144 
145 		/* Put DSI lanes to ULPS to disable pipe */
146 		REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 2, 2, 1);
147 		REG_READ(MIPI_DEVICE_READY_REG(pipe)); /* posted write? */
148 
149 		/* LP Hold */
150 		REG_FLD_MOD(MIPI_PORT_CONTROL(pipe), 0, 16, 16);
151 		REG_READ(MIPI_PORT_CONTROL(pipe)); /* posted write? */
152 
153 		/* Disable display plane */
154 		REG_FLD_MOD(dspcntr_reg, 0, 31, 31);
155 
156 		/* Flush the plane changes ??? posted write? */
157 		REG_WRITE(dspbase_reg, REG_READ(dspbase_reg));
158 		REG_READ(dspbase_reg);
159 
160 		/* Disable PIPE */
161 		REG_FLD_MOD(pipeconf_reg, 0, 31, 31);
162 
163 		if (REG_BIT_WAIT(pipeconf_reg, 0, 30))
164 			dev_err(&dev->pdev->dev, "%s: Pipe disable timeout\n",
165 				__func__);
166 
167 		if (REG_BIT_WAIT(MIPI_GEN_FIFO_STAT_REG(pipe), 1, 28))
168 			dev_err(&dev->pdev->dev, "%s: FIFO not empty\n",
169 				__func__);
170 	}
171 }
172 
mdfld_dsi_configure_down(struct mdfld_dsi_encoder * dsi_encoder,int pipe)173 static void mdfld_dsi_configure_down(struct mdfld_dsi_encoder *dsi_encoder,
174 								int pipe)
175 {
176 	struct mdfld_dsi_dpi_output *dpi_output =
177 				MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
178 	struct mdfld_dsi_config *dsi_config =
179 				mdfld_dsi_encoder_get_config(dsi_encoder);
180 	struct drm_device *dev = dsi_config->dev;
181 	struct drm_psb_private *dev_priv = dev->dev_private;
182 
183 	if (!dev_priv->dpi_panel_on[pipe]) {
184 		dev_err(dev->dev, "DPI panel is already off\n");
185 		return;
186 	}
187 	tc35876x_toshiba_bridge_panel_off(dev);
188 	tc35876x_set_bridge_reset_state(dev, 1);
189 	dsi_set_pipe_plane_enable_state(dev, 0, pipe);
190 	mdfld_dsi_dpi_shut_down(dpi_output, pipe);
191 	dsi_set_device_ready_state(dev, 0, pipe);
192 }
193 
mdfld_dsi_configure_up(struct mdfld_dsi_encoder * dsi_encoder,int pipe)194 static void mdfld_dsi_configure_up(struct mdfld_dsi_encoder *dsi_encoder,
195 								int pipe)
196 {
197 	struct mdfld_dsi_dpi_output *dpi_output =
198 				MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
199 	struct mdfld_dsi_config *dsi_config =
200 				mdfld_dsi_encoder_get_config(dsi_encoder);
201 	struct drm_device *dev = dsi_config->dev;
202 	struct drm_psb_private *dev_priv = dev->dev_private;
203 
204 	if (dev_priv->dpi_panel_on[pipe]) {
205 		dev_err(dev->dev, "DPI panel is already on\n");
206 		return;
207 	}
208 
209 	/* For resume path sequence */
210 	mdfld_dsi_dpi_shut_down(dpi_output, pipe);
211 	dsi_set_device_ready_state(dev, 0, pipe);
212 
213 	dsi_set_device_ready_state(dev, 1, pipe);
214 	tc35876x_set_bridge_reset_state(dev, 0);
215 	tc35876x_configure_lvds_bridge(dev);
216 	mdfld_dsi_dpi_turn_on(dpi_output, pipe);  /* Send turn on command */
217 	dsi_set_pipe_plane_enable_state(dev, 1, pipe);
218 }
219 /* End for TC35876X */
220 
221 /* ************************************************************************* *\
222  * FUNCTION: mdfld_dsi_tpo_ic_init
223  *
224  * DESCRIPTION:  This function is called only by mrst_dsi_mode_set and
225  *               restore_display_registers.  since this function does not
226  *               acquire the mutex, it is important that the calling function
227  *               does!
228 \* ************************************************************************* */
mdfld_dsi_tpo_ic_init(struct mdfld_dsi_config * dsi_config,u32 pipe)229 static void mdfld_dsi_tpo_ic_init(struct mdfld_dsi_config *dsi_config, u32 pipe)
230 {
231 	struct drm_device *dev = dsi_config->dev;
232 	u32 dcsChannelNumber = dsi_config->channel_num;
233 	u32 gen_data_reg = MIPI_HS_GEN_DATA_REG(pipe);
234 	u32 gen_ctrl_reg = MIPI_HS_GEN_CTRL_REG(pipe);
235 	u32 gen_ctrl_val = GEN_LONG_WRITE;
236 
237 	DRM_INFO("Enter mrst init TPO MIPI display.\n");
238 
239 	gen_ctrl_val |= dcsChannelNumber << DCS_CHANNEL_NUMBER_POS;
240 
241 	/* Flip page order */
242 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
243 	REG_WRITE(gen_data_reg, 0x00008036);
244 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
245 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x02 << WORD_COUNTS_POS));
246 
247 	/* 0xF0 */
248 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
249 	REG_WRITE(gen_data_reg, 0x005a5af0);
250 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
251 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
252 
253 	/* Write protection key */
254 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
255 	REG_WRITE(gen_data_reg, 0x005a5af1);
256 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
257 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
258 
259 	/* 0xFC */
260 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
261 	REG_WRITE(gen_data_reg, 0x005a5afc);
262 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
263 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
264 
265 	/* 0xB7 */
266 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
267 	REG_WRITE(gen_data_reg, 0x770000b7);
268 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
269 	REG_WRITE(gen_data_reg, 0x00000044);
270 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
271 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x05 << WORD_COUNTS_POS));
272 
273 	/* 0xB6 */
274 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
275 	REG_WRITE(gen_data_reg, 0x000a0ab6);
276 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
277 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
278 
279 	/* 0xF2 */
280 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
281 	REG_WRITE(gen_data_reg, 0x081010f2);
282 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
283 	REG_WRITE(gen_data_reg, 0x4a070708);
284 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
285 	REG_WRITE(gen_data_reg, 0x000000c5);
286 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
287 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS));
288 
289 	/* 0xF8 */
290 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
291 	REG_WRITE(gen_data_reg, 0x024003f8);
292 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
293 	REG_WRITE(gen_data_reg, 0x01030a04);
294 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
295 	REG_WRITE(gen_data_reg, 0x0e020220);
296 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
297 	REG_WRITE(gen_data_reg, 0x00000004);
298 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
299 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x0d << WORD_COUNTS_POS));
300 
301 	/* 0xE2 */
302 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
303 	REG_WRITE(gen_data_reg, 0x398fc3e2);
304 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
305 	REG_WRITE(gen_data_reg, 0x0000916f);
306 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
307 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x06 << WORD_COUNTS_POS));
308 
309 	/* 0xB0 */
310 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
311 	REG_WRITE(gen_data_reg, 0x000000b0);
312 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
313 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x02 << WORD_COUNTS_POS));
314 
315 	/* 0xF4 */
316 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
317 	REG_WRITE(gen_data_reg, 0x240242f4);
318 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
319 	REG_WRITE(gen_data_reg, 0x78ee2002);
320 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
321 	REG_WRITE(gen_data_reg, 0x2a071050);
322 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
323 	REG_WRITE(gen_data_reg, 0x507fee10);
324 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
325 	REG_WRITE(gen_data_reg, 0x10300710);
326 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
327 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x14 << WORD_COUNTS_POS));
328 
329 	/* 0xBA */
330 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
331 	REG_WRITE(gen_data_reg, 0x19fe07ba);
332 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
333 	REG_WRITE(gen_data_reg, 0x101c0a31);
334 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
335 	REG_WRITE(gen_data_reg, 0x00000010);
336 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
337 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS));
338 
339 	/* 0xBB */
340 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
341 	REG_WRITE(gen_data_reg, 0x28ff07bb);
342 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
343 	REG_WRITE(gen_data_reg, 0x24280a31);
344 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
345 	REG_WRITE(gen_data_reg, 0x00000034);
346 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
347 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x09 << WORD_COUNTS_POS));
348 
349 	/* 0xFB */
350 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
351 	REG_WRITE(gen_data_reg, 0x535d05fb);
352 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
353 	REG_WRITE(gen_data_reg, 0x1b1a2130);
354 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
355 	REG_WRITE(gen_data_reg, 0x221e180e);
356 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
357 	REG_WRITE(gen_data_reg, 0x131d2120);
358 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
359 	REG_WRITE(gen_data_reg, 0x535d0508);
360 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
361 	REG_WRITE(gen_data_reg, 0x1c1a2131);
362 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
363 	REG_WRITE(gen_data_reg, 0x231f160d);
364 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
365 	REG_WRITE(gen_data_reg, 0x111b2220);
366 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
367 	REG_WRITE(gen_data_reg, 0x535c2008);
368 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
369 	REG_WRITE(gen_data_reg, 0x1f1d2433);
370 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
371 	REG_WRITE(gen_data_reg, 0x2c251a10);
372 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
373 	REG_WRITE(gen_data_reg, 0x2c34372d);
374 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
375 	REG_WRITE(gen_data_reg, 0x00000023);
376 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
377 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x31 << WORD_COUNTS_POS));
378 
379 	/* 0xFA */
380 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
381 	REG_WRITE(gen_data_reg, 0x525c0bfa);
382 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
383 	REG_WRITE(gen_data_reg, 0x1c1c232f);
384 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
385 	REG_WRITE(gen_data_reg, 0x2623190e);
386 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
387 	REG_WRITE(gen_data_reg, 0x18212625);
388 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
389 	REG_WRITE(gen_data_reg, 0x545d0d0e);
390 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
391 	REG_WRITE(gen_data_reg, 0x1e1d2333);
392 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
393 	REG_WRITE(gen_data_reg, 0x26231a10);
394 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
395 	REG_WRITE(gen_data_reg, 0x1a222725);
396 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
397 	REG_WRITE(gen_data_reg, 0x545d280f);
398 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
399 	REG_WRITE(gen_data_reg, 0x21202635);
400 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
401 	REG_WRITE(gen_data_reg, 0x31292013);
402 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
403 	REG_WRITE(gen_data_reg, 0x31393d33);
404 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
405 	REG_WRITE(gen_data_reg, 0x00000029);
406 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
407 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x31 << WORD_COUNTS_POS));
408 
409 	/* Set DM */
410 	mdfld_wait_for_HS_DATA_FIFO(dev, pipe);
411 	REG_WRITE(gen_data_reg, 0x000100f7);
412 	mdfld_wait_for_HS_CTRL_FIFO(dev, pipe);
413 	REG_WRITE(gen_ctrl_reg, gen_ctrl_val | (0x03 << WORD_COUNTS_POS));
414 }
415 
mdfld_dsi_dpi_to_byte_clock_count(int pixel_clock_count,int num_lane,int bpp)416 static u16 mdfld_dsi_dpi_to_byte_clock_count(int pixel_clock_count,
417 						int num_lane, int bpp)
418 {
419 	return (u16)((pixel_clock_count * bpp) / (num_lane * 8));
420 }
421 
422 /*
423  * Calculate the dpi time basing on a given drm mode @mode
424  * return 0 on success.
425  * FIXME: I was using proposed mode value for calculation, may need to
426  * use crtc mode values later
427  */
mdfld_dsi_dpi_timing_calculation(struct drm_display_mode * mode,struct mdfld_dsi_dpi_timing * dpi_timing,int num_lane,int bpp)428 int mdfld_dsi_dpi_timing_calculation(struct drm_display_mode *mode,
429 				struct mdfld_dsi_dpi_timing *dpi_timing,
430 				int num_lane, int bpp)
431 {
432 	int pclk_hsync, pclk_hfp, pclk_hbp, pclk_hactive;
433 	int pclk_vsync, pclk_vfp, pclk_vbp;
434 
435 	pclk_hactive = mode->hdisplay;
436 	pclk_hfp = mode->hsync_start - mode->hdisplay;
437 	pclk_hsync = mode->hsync_end - mode->hsync_start;
438 	pclk_hbp = mode->htotal - mode->hsync_end;
439 
440 	pclk_vfp = mode->vsync_start - mode->vdisplay;
441 	pclk_vsync = mode->vsync_end - mode->vsync_start;
442 	pclk_vbp = mode->vtotal - mode->vsync_end;
443 
444 	/*
445 	 * byte clock counts were calculated by following formula
446 	 * bclock_count = pclk_count * bpp / num_lane / 8
447 	 */
448 	dpi_timing->hsync_count = mdfld_dsi_dpi_to_byte_clock_count(
449 						pclk_hsync, num_lane, bpp);
450 	dpi_timing->hbp_count = mdfld_dsi_dpi_to_byte_clock_count(
451 						pclk_hbp, num_lane, bpp);
452 	dpi_timing->hfp_count = mdfld_dsi_dpi_to_byte_clock_count(
453 						pclk_hfp, num_lane, bpp);
454 	dpi_timing->hactive_count = mdfld_dsi_dpi_to_byte_clock_count(
455 						pclk_hactive, num_lane, bpp);
456 	dpi_timing->vsync_count = mdfld_dsi_dpi_to_byte_clock_count(
457 						pclk_vsync, num_lane, bpp);
458 	dpi_timing->vbp_count = mdfld_dsi_dpi_to_byte_clock_count(
459 						pclk_vbp, num_lane, bpp);
460 	dpi_timing->vfp_count = mdfld_dsi_dpi_to_byte_clock_count(
461 						pclk_vfp, num_lane, bpp);
462 
463 	return 0;
464 }
465 
mdfld_dsi_dpi_controller_init(struct mdfld_dsi_config * dsi_config,int pipe)466 void mdfld_dsi_dpi_controller_init(struct mdfld_dsi_config *dsi_config,
467 								int pipe)
468 {
469 	struct drm_device *dev = dsi_config->dev;
470 	int lane_count = dsi_config->lane_count;
471 	struct mdfld_dsi_dpi_timing dpi_timing;
472 	struct drm_display_mode *mode = dsi_config->mode;
473 	u32 val;
474 
475 	/*un-ready device*/
476 	REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 0, 0, 0);
477 
478 	/*init dsi adapter before kicking off*/
479 	REG_WRITE(MIPI_CTRL_REG(pipe), 0x00000018);
480 
481 	/*enable all interrupts*/
482 	REG_WRITE(MIPI_INTR_EN_REG(pipe), 0xffffffff);
483 
484 	/*set up func_prg*/
485 	val = lane_count;
486 	val |= dsi_config->channel_num << DSI_DPI_VIRT_CHANNEL_OFFSET;
487 
488 	switch (dsi_config->bpp) {
489 	case 16:
490 		val |= DSI_DPI_COLOR_FORMAT_RGB565;
491 		break;
492 	case 18:
493 		val |= DSI_DPI_COLOR_FORMAT_RGB666;
494 		break;
495 	case 24:
496 		val |= DSI_DPI_COLOR_FORMAT_RGB888;
497 		break;
498 	default:
499 		DRM_ERROR("unsupported color format, bpp = %d\n",
500 							dsi_config->bpp);
501 	}
502 	REG_WRITE(MIPI_DSI_FUNC_PRG_REG(pipe), val);
503 
504 	REG_WRITE(MIPI_HS_TX_TIMEOUT_REG(pipe),
505 			(mode->vtotal * mode->htotal * dsi_config->bpp /
506 				(8 * lane_count)) & DSI_HS_TX_TIMEOUT_MASK);
507 	REG_WRITE(MIPI_LP_RX_TIMEOUT_REG(pipe),
508 				0xffff & DSI_LP_RX_TIMEOUT_MASK);
509 
510 	/*max value: 20 clock cycles of txclkesc*/
511 	REG_WRITE(MIPI_TURN_AROUND_TIMEOUT_REG(pipe),
512 				0x14 & DSI_TURN_AROUND_TIMEOUT_MASK);
513 
514 	/*min 21 txclkesc, max: ffffh*/
515 	REG_WRITE(MIPI_DEVICE_RESET_TIMER_REG(pipe),
516 				0xffff & DSI_RESET_TIMER_MASK);
517 
518 	REG_WRITE(MIPI_DPI_RESOLUTION_REG(pipe),
519 				mode->vdisplay << 16 | mode->hdisplay);
520 
521 	/*set DPI timing registers*/
522 	mdfld_dsi_dpi_timing_calculation(mode, &dpi_timing,
523 				dsi_config->lane_count, dsi_config->bpp);
524 
525 	REG_WRITE(MIPI_HSYNC_COUNT_REG(pipe),
526 			dpi_timing.hsync_count & DSI_DPI_TIMING_MASK);
527 	REG_WRITE(MIPI_HBP_COUNT_REG(pipe),
528 			dpi_timing.hbp_count & DSI_DPI_TIMING_MASK);
529 	REG_WRITE(MIPI_HFP_COUNT_REG(pipe),
530 			dpi_timing.hfp_count & DSI_DPI_TIMING_MASK);
531 	REG_WRITE(MIPI_HACTIVE_COUNT_REG(pipe),
532 			dpi_timing.hactive_count & DSI_DPI_TIMING_MASK);
533 	REG_WRITE(MIPI_VSYNC_COUNT_REG(pipe),
534 			dpi_timing.vsync_count & DSI_DPI_TIMING_MASK);
535 	REG_WRITE(MIPI_VBP_COUNT_REG(pipe),
536 			dpi_timing.vbp_count & DSI_DPI_TIMING_MASK);
537 	REG_WRITE(MIPI_VFP_COUNT_REG(pipe),
538 			dpi_timing.vfp_count & DSI_DPI_TIMING_MASK);
539 
540 	REG_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT_REG(pipe), 0x46);
541 
542 	/*min: 7d0 max: 4e20*/
543 	REG_WRITE(MIPI_INIT_COUNT_REG(pipe), 0x000007d0);
544 
545 	/*set up video mode*/
546 	val = dsi_config->video_mode | DSI_DPI_COMPLETE_LAST_LINE;
547 	REG_WRITE(MIPI_VIDEO_MODE_FORMAT_REG(pipe), val);
548 
549 	REG_WRITE(MIPI_EOT_DISABLE_REG(pipe), 0x00000000);
550 
551 	REG_WRITE(MIPI_LP_BYTECLK_REG(pipe), 0x00000004);
552 
553 	/*TODO: figure out how to setup these registers*/
554 	if (mdfld_get_panel_type(dev, pipe) == TC35876X)
555 		REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x2A0c6008);
556 	else
557 		REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x150c3408);
558 
559 	REG_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT_REG(pipe), (0xa << 16) | 0x14);
560 
561 	if (mdfld_get_panel_type(dev, pipe) == TC35876X)
562 		tc35876x_set_bridge_reset_state(dev, 0);  /*Pull High Reset */
563 
564 	/*set device ready*/
565 	REG_FLD_MOD(MIPI_DEVICE_READY_REG(pipe), 1, 0, 0);
566 }
567 
mdfld_dsi_dpi_turn_on(struct mdfld_dsi_dpi_output * output,int pipe)568 void mdfld_dsi_dpi_turn_on(struct mdfld_dsi_dpi_output *output, int pipe)
569 {
570 	struct drm_device *dev = output->dev;
571 
572 	/* clear special packet sent bit */
573 	if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT)
574 		REG_WRITE(MIPI_INTR_STAT_REG(pipe),
575 					DSI_INTR_STATE_SPL_PKG_SENT);
576 
577 	/*send turn on package*/
578 	REG_WRITE(MIPI_DPI_CONTROL_REG(pipe), DSI_DPI_CTRL_HS_TURN_ON);
579 
580 	/*wait for SPL_PKG_SENT interrupt*/
581 	mdfld_wait_for_SPL_PKG_SENT(dev, pipe);
582 
583 	if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT)
584 		REG_WRITE(MIPI_INTR_STAT_REG(pipe),
585 					DSI_INTR_STATE_SPL_PKG_SENT);
586 
587 	output->panel_on = 1;
588 
589 	/* FIXME the following is disabled to WA the X slow start issue
590 	   for TMD panel
591 	if (pipe == 2)
592 		dev_priv->dpi_panel_on2 = true;
593 	else if (pipe == 0)
594 		dev_priv->dpi_panel_on = true; */
595 }
596 
mdfld_dsi_dpi_shut_down(struct mdfld_dsi_dpi_output * output,int pipe)597 static void mdfld_dsi_dpi_shut_down(struct mdfld_dsi_dpi_output *output,
598 								int pipe)
599 {
600 	struct drm_device *dev = output->dev;
601 
602 	/*if output is on, or mode setting didn't happen, ignore this*/
603 	if ((!output->panel_on) || output->first_boot) {
604 		output->first_boot = 0;
605 		return;
606 	}
607 
608 	/* Wait for dpi fifo to empty */
609 	mdfld_wait_for_DPI_CTRL_FIFO(dev, pipe);
610 
611 	/* Clear the special packet interrupt bit if set */
612 	if (REG_READ(MIPI_INTR_STAT_REG(pipe)) & DSI_INTR_STATE_SPL_PKG_SENT)
613 		REG_WRITE(MIPI_INTR_STAT_REG(pipe),
614 					DSI_INTR_STATE_SPL_PKG_SENT);
615 
616 	if (REG_READ(MIPI_DPI_CONTROL_REG(pipe)) == DSI_DPI_CTRL_HS_SHUTDOWN)
617 		goto shutdown_out;
618 
619 	REG_WRITE(MIPI_DPI_CONTROL_REG(pipe), DSI_DPI_CTRL_HS_SHUTDOWN);
620 
621 shutdown_out:
622 	output->panel_on = 0;
623 	output->first_boot = 0;
624 
625 	/* FIXME the following is disabled to WA the X slow start issue
626 	   for TMD panel
627 	if (pipe == 2)
628 		dev_priv->dpi_panel_on2 = false;
629 	else if (pipe == 0)
630 		dev_priv->dpi_panel_on = false;	 */
631 }
632 
mdfld_dsi_dpi_set_power(struct drm_encoder * encoder,bool on)633 static void mdfld_dsi_dpi_set_power(struct drm_encoder *encoder, bool on)
634 {
635 	struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder);
636 	struct mdfld_dsi_dpi_output *dpi_output =
637 				MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
638 	struct mdfld_dsi_config *dsi_config =
639 				mdfld_dsi_encoder_get_config(dsi_encoder);
640 	int pipe = mdfld_dsi_encoder_get_pipe(dsi_encoder);
641 	struct drm_device *dev = dsi_config->dev;
642 	struct drm_psb_private *dev_priv = dev->dev_private;
643 
644 	/*start up display island if it was shutdown*/
645 	if (!gma_power_begin(dev, true))
646 		return;
647 
648 	if (on) {
649 		if (mdfld_get_panel_type(dev, pipe) == TMD_VID)
650 			mdfld_dsi_dpi_turn_on(dpi_output, pipe);
651 		else if (mdfld_get_panel_type(dev, pipe) == TC35876X)
652 			mdfld_dsi_configure_up(dsi_encoder, pipe);
653 		else {
654 			/*enable mipi port*/
655 			REG_WRITE(MIPI_PORT_CONTROL(pipe),
656 				REG_READ(MIPI_PORT_CONTROL(pipe)) | BIT(31));
657 			REG_READ(MIPI_PORT_CONTROL(pipe));
658 
659 			mdfld_dsi_dpi_turn_on(dpi_output, pipe);
660 			mdfld_dsi_tpo_ic_init(dsi_config, pipe);
661 		}
662 		dev_priv->dpi_panel_on[pipe] = true;
663 	} else {
664 		if (mdfld_get_panel_type(dev, pipe) == TMD_VID)
665 			mdfld_dsi_dpi_shut_down(dpi_output, pipe);
666 		else if (mdfld_get_panel_type(dev, pipe) == TC35876X)
667 			mdfld_dsi_configure_down(dsi_encoder, pipe);
668 		else {
669 			mdfld_dsi_dpi_shut_down(dpi_output, pipe);
670 
671 			/*disable mipi port*/
672 			REG_WRITE(MIPI_PORT_CONTROL(pipe),
673 				REG_READ(MIPI_PORT_CONTROL(pipe)) & ~BIT(31));
674 			REG_READ(MIPI_PORT_CONTROL(pipe));
675 		}
676 		dev_priv->dpi_panel_on[pipe] = false;
677 	}
678 	gma_power_end(dev);
679 }
680 
mdfld_dsi_dpi_dpms(struct drm_encoder * encoder,int mode)681 void mdfld_dsi_dpi_dpms(struct drm_encoder *encoder, int mode)
682 {
683 	mdfld_dsi_dpi_set_power(encoder, mode == DRM_MODE_DPMS_ON);
684 }
685 
mdfld_dsi_dpi_mode_fixup(struct drm_encoder * encoder,struct drm_display_mode * mode,struct drm_display_mode * adjusted_mode)686 bool mdfld_dsi_dpi_mode_fixup(struct drm_encoder *encoder,
687 				     struct drm_display_mode *mode,
688 				     struct drm_display_mode *adjusted_mode)
689 {
690 	struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder);
691 	struct mdfld_dsi_config *dsi_config =
692 				mdfld_dsi_encoder_get_config(dsi_encoder);
693 	struct drm_display_mode *fixed_mode = dsi_config->fixed_mode;
694 
695 	if (fixed_mode) {
696 		adjusted_mode->hdisplay = fixed_mode->hdisplay;
697 		adjusted_mode->hsync_start = fixed_mode->hsync_start;
698 		adjusted_mode->hsync_end = fixed_mode->hsync_end;
699 		adjusted_mode->htotal = fixed_mode->htotal;
700 		adjusted_mode->vdisplay = fixed_mode->vdisplay;
701 		adjusted_mode->vsync_start = fixed_mode->vsync_start;
702 		adjusted_mode->vsync_end = fixed_mode->vsync_end;
703 		adjusted_mode->vtotal = fixed_mode->vtotal;
704 		adjusted_mode->clock = fixed_mode->clock;
705 		drm_mode_set_crtcinfo(adjusted_mode, CRTC_INTERLACE_HALVE_V);
706 	}
707 	return true;
708 }
709 
mdfld_dsi_dpi_prepare(struct drm_encoder * encoder)710 void mdfld_dsi_dpi_prepare(struct drm_encoder *encoder)
711 {
712 	mdfld_dsi_dpi_set_power(encoder, false);
713 }
714 
mdfld_dsi_dpi_commit(struct drm_encoder * encoder)715 void mdfld_dsi_dpi_commit(struct drm_encoder *encoder)
716 {
717 	mdfld_dsi_dpi_set_power(encoder, true);
718 }
719 
720 /* For TC35876X */
721 /* This functionality was implemented in FW in iCDK */
722 /* But removed in DV0 and later. So need to add here. */
mipi_set_properties(struct mdfld_dsi_config * dsi_config,int pipe)723 static void mipi_set_properties(struct mdfld_dsi_config *dsi_config, int pipe)
724 {
725 	struct drm_device *dev = dsi_config->dev;
726 
727 	REG_WRITE(MIPI_CTRL_REG(pipe), 0x00000018);
728 	REG_WRITE(MIPI_INTR_EN_REG(pipe), 0xffffffff);
729 	REG_WRITE(MIPI_HS_TX_TIMEOUT_REG(pipe), 0xffffff);
730 	REG_WRITE(MIPI_LP_RX_TIMEOUT_REG(pipe), 0xffffff);
731 	REG_WRITE(MIPI_TURN_AROUND_TIMEOUT_REG(pipe), 0x14);
732 	REG_WRITE(MIPI_DEVICE_RESET_TIMER_REG(pipe), 0xff);
733 	REG_WRITE(MIPI_HIGH_LOW_SWITCH_COUNT_REG(pipe), 0x25);
734 	REG_WRITE(MIPI_INIT_COUNT_REG(pipe), 0xf0);
735 	REG_WRITE(MIPI_EOT_DISABLE_REG(pipe), 0x00000000);
736 	REG_WRITE(MIPI_LP_BYTECLK_REG(pipe), 0x00000004);
737 	REG_WRITE(MIPI_DBI_BW_CTRL_REG(pipe), 0x00000820);
738 	REG_WRITE(MIPI_CLK_LANE_SWITCH_TIME_CNT_REG(pipe), (0xa << 16) | 0x14);
739 }
740 
mdfld_mipi_set_video_timing(struct mdfld_dsi_config * dsi_config,int pipe)741 static void mdfld_mipi_set_video_timing(struct mdfld_dsi_config *dsi_config,
742 					int pipe)
743 {
744 	struct drm_device *dev = dsi_config->dev;
745 	struct mdfld_dsi_dpi_timing dpi_timing;
746 	struct drm_display_mode *mode = dsi_config->mode;
747 
748 	mdfld_dsi_dpi_timing_calculation(mode, &dpi_timing,
749 					dsi_config->lane_count,
750 					dsi_config->bpp);
751 
752 	REG_WRITE(MIPI_DPI_RESOLUTION_REG(pipe),
753 		mode->vdisplay << 16 | mode->hdisplay);
754 	REG_WRITE(MIPI_HSYNC_COUNT_REG(pipe),
755 		dpi_timing.hsync_count & DSI_DPI_TIMING_MASK);
756 	REG_WRITE(MIPI_HBP_COUNT_REG(pipe),
757 		dpi_timing.hbp_count & DSI_DPI_TIMING_MASK);
758 	REG_WRITE(MIPI_HFP_COUNT_REG(pipe),
759 		dpi_timing.hfp_count & DSI_DPI_TIMING_MASK);
760 	REG_WRITE(MIPI_HACTIVE_COUNT_REG(pipe),
761 		dpi_timing.hactive_count & DSI_DPI_TIMING_MASK);
762 	REG_WRITE(MIPI_VSYNC_COUNT_REG(pipe),
763 		dpi_timing.vsync_count & DSI_DPI_TIMING_MASK);
764 	REG_WRITE(MIPI_VBP_COUNT_REG(pipe),
765 		dpi_timing.vbp_count & DSI_DPI_TIMING_MASK);
766 	REG_WRITE(MIPI_VFP_COUNT_REG(pipe),
767 		dpi_timing.vfp_count & DSI_DPI_TIMING_MASK);
768 }
769 
mdfld_mipi_config(struct mdfld_dsi_config * dsi_config,int pipe)770 static void mdfld_mipi_config(struct mdfld_dsi_config *dsi_config, int pipe)
771 {
772 	struct drm_device *dev = dsi_config->dev;
773 	int lane_count = dsi_config->lane_count;
774 
775 	if (pipe) {
776 		REG_WRITE(MIPI_PORT_CONTROL(0), 0x00000002);
777 		REG_WRITE(MIPI_PORT_CONTROL(2), 0x80000000);
778 	} else {
779 		REG_WRITE(MIPI_PORT_CONTROL(0), 0x80010000);
780 		REG_WRITE(MIPI_PORT_CONTROL(2), 0x00);
781 	}
782 
783 	REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x150A600F);
784 	REG_WRITE(MIPI_VIDEO_MODE_FORMAT_REG(pipe), 0x0000000F);
785 
786 	/* lane_count = 3 */
787 	REG_WRITE(MIPI_DSI_FUNC_PRG_REG(pipe), 0x00000200 | lane_count);
788 
789 	mdfld_mipi_set_video_timing(dsi_config, pipe);
790 }
791 
mdfld_set_pipe_timing(struct mdfld_dsi_config * dsi_config,int pipe)792 static void mdfld_set_pipe_timing(struct mdfld_dsi_config *dsi_config, int pipe)
793 {
794 	struct drm_device *dev = dsi_config->dev;
795 	struct drm_display_mode *mode = dsi_config->mode;
796 
797 	REG_WRITE(HTOTAL_A, ((mode->htotal - 1) << 16) | (mode->hdisplay - 1));
798 	REG_WRITE(HBLANK_A, ((mode->htotal - 1) << 16) | (mode->hdisplay - 1));
799 	REG_WRITE(HSYNC_A,
800 		((mode->hsync_end - 1) << 16) | (mode->hsync_start - 1));
801 
802 	REG_WRITE(VTOTAL_A, ((mode->vtotal - 1) << 16) | (mode->vdisplay - 1));
803 	REG_WRITE(VBLANK_A, ((mode->vtotal - 1) << 16) | (mode->vdisplay - 1));
804 	REG_WRITE(VSYNC_A,
805 		((mode->vsync_end - 1) << 16) | (mode->vsync_start - 1));
806 
807 	REG_WRITE(PIPEASRC,
808 		((mode->hdisplay - 1) << 16) | (mode->vdisplay - 1));
809 }
810 /* End for TC35876X */
811 
mdfld_dsi_dpi_mode_set(struct drm_encoder * encoder,struct drm_display_mode * mode,struct drm_display_mode * adjusted_mode)812 void mdfld_dsi_dpi_mode_set(struct drm_encoder *encoder,
813 				   struct drm_display_mode *mode,
814 				   struct drm_display_mode *adjusted_mode)
815 {
816 	struct mdfld_dsi_encoder *dsi_encoder = mdfld_dsi_encoder(encoder);
817 	struct mdfld_dsi_dpi_output *dpi_output =
818 					MDFLD_DSI_DPI_OUTPUT(dsi_encoder);
819 	struct mdfld_dsi_config *dsi_config =
820 				mdfld_dsi_encoder_get_config(dsi_encoder);
821 	struct drm_device *dev = dsi_config->dev;
822 	struct drm_psb_private *dev_priv = dev->dev_private;
823 	int pipe = mdfld_dsi_encoder_get_pipe(dsi_encoder);
824 
825 	u32 pipeconf_reg = PIPEACONF;
826 	u32 dspcntr_reg = DSPACNTR;
827 
828 	u32 pipeconf = dev_priv->pipeconf[pipe];
829 	u32 dspcntr = dev_priv->dspcntr[pipe];
830 	u32 mipi = MIPI_PORT_EN | PASS_FROM_SPHY_TO_AFE | SEL_FLOPPED_HSTX;
831 
832 	if (pipe) {
833 		pipeconf_reg = PIPECCONF;
834 		dspcntr_reg = DSPCCNTR;
835 	} else {
836 		if (mdfld_get_panel_type(dev, pipe) == TC35876X)
837 			mipi &= (~0x03); /* Use all four lanes */
838 		else
839 			mipi |= 2;
840 	}
841 
842 	/*start up display island if it was shutdown*/
843 	if (!gma_power_begin(dev, true))
844 		return;
845 
846 	if (mdfld_get_panel_type(dev, pipe) == TC35876X) {
847 		/*
848 		 * The following logic is required to reset the bridge and
849 		 * configure. This also starts the DSI clock at 200MHz.
850 		 */
851 		tc35876x_set_bridge_reset_state(dev, 0);  /*Pull High Reset */
852 		tc35876x_toshiba_bridge_panel_on(dev);
853 		udelay(100);
854 		/* Now start the DSI clock */
855 		REG_WRITE(MRST_DPLL_A, 0x00);
856 		REG_WRITE(MRST_FPA0, 0xC1);
857 		REG_WRITE(MRST_DPLL_A, 0x00800000);
858 		udelay(500);
859 		REG_WRITE(MRST_DPLL_A, 0x80800000);
860 
861 		if (REG_BIT_WAIT(pipeconf_reg, 1, 29))
862 			dev_err(&dev->pdev->dev, "%s: DSI PLL lock timeout\n",
863 				__func__);
864 
865 		REG_WRITE(MIPI_DPHY_PARAM_REG(pipe), 0x2A0c6008);
866 
867 		mipi_set_properties(dsi_config, pipe);
868 		mdfld_mipi_config(dsi_config, pipe);
869 		mdfld_set_pipe_timing(dsi_config, pipe);
870 
871 		REG_WRITE(DSPABASE, 0x00);
872 		REG_WRITE(DSPASTRIDE, (mode->hdisplay * 4));
873 		REG_WRITE(DSPASIZE,
874 			((mode->vdisplay - 1) << 16) | (mode->hdisplay - 1));
875 
876 		REG_WRITE(DSPACNTR, 0x98000000);
877 		REG_WRITE(DSPASURF, 0x00);
878 
879 		REG_WRITE(VGACNTRL, 0x80000000);
880 		REG_WRITE(DEVICE_READY_REG, 0x00000001);
881 
882 		REG_WRITE(MIPI_PORT_CONTROL(pipe), 0x80810000);
883 	} else {
884 		/*set up mipi port FIXME: do at init time */
885 		REG_WRITE(MIPI_PORT_CONTROL(pipe), mipi);
886 	}
887 	REG_READ(MIPI_PORT_CONTROL(pipe));
888 
889 	if (mdfld_get_panel_type(dev, pipe) == TMD_VID) {
890 		/* NOP */
891 	} else if (mdfld_get_panel_type(dev, pipe) == TC35876X) {
892 		/* set up DSI controller DPI interface */
893 		mdfld_dsi_dpi_controller_init(dsi_config, pipe);
894 
895 		/* Configure MIPI Bridge and Panel */
896 		tc35876x_configure_lvds_bridge(dev);
897 		dev_priv->dpi_panel_on[pipe] = true;
898 	} else {
899 		/*turn on DPI interface*/
900 		mdfld_dsi_dpi_turn_on(dpi_output, pipe);
901 	}
902 
903 	/*set up pipe*/
904 	REG_WRITE(pipeconf_reg, pipeconf);
905 	REG_READ(pipeconf_reg);
906 
907 	/*set up display plane*/
908 	REG_WRITE(dspcntr_reg, dspcntr);
909 	REG_READ(dspcntr_reg);
910 
911 	msleep(20); /* FIXME: this should wait for vblank */
912 
913 	if (mdfld_get_panel_type(dev, pipe) == TMD_VID) {
914 		/* NOP */
915 	} else if (mdfld_get_panel_type(dev, pipe) == TC35876X) {
916 		mdfld_dsi_dpi_turn_on(dpi_output, pipe);
917 	} else {
918 		/* init driver ic */
919 		mdfld_dsi_tpo_ic_init(dsi_config, pipe);
920 		/*init backlight*/
921 		mdfld_dsi_brightness_init(dsi_config, pipe);
922 	}
923 
924 	gma_power_end(dev);
925 }
926 
927 /*
928  * Init DSI DPI encoder.
929  * Allocate an mdfld_dsi_encoder and attach it to given @dsi_connector
930  * return pointer of newly allocated DPI encoder, NULL on error
931  */
mdfld_dsi_dpi_init(struct drm_device * dev,struct mdfld_dsi_connector * dsi_connector,const struct panel_funcs * p_funcs)932 struct mdfld_dsi_encoder *mdfld_dsi_dpi_init(struct drm_device *dev,
933 				struct mdfld_dsi_connector *dsi_connector,
934 				const struct panel_funcs *p_funcs)
935 {
936 	struct mdfld_dsi_dpi_output *dpi_output = NULL;
937 	struct mdfld_dsi_config *dsi_config;
938 	struct drm_connector *connector = NULL;
939 	struct drm_encoder *encoder = NULL;
940 	int pipe;
941 	u32 data;
942 	int ret;
943 
944 	pipe = dsi_connector->pipe;
945 
946 	if (mdfld_get_panel_type(dev, pipe) != TC35876X) {
947 		dsi_config = mdfld_dsi_get_config(dsi_connector);
948 
949 		/* panel hard-reset */
950 		if (p_funcs->reset) {
951 			ret = p_funcs->reset(pipe);
952 			if (ret) {
953 				DRM_ERROR("Panel %d hard-reset failed\n", pipe);
954 				return NULL;
955 			}
956 		}
957 
958 		/* panel drvIC init */
959 		if (p_funcs->drv_ic_init)
960 			p_funcs->drv_ic_init(dsi_config, pipe);
961 
962 		/* panel power mode detect */
963 		ret = mdfld_dsi_get_power_mode(dsi_config, &data, false);
964 		if (ret) {
965 			DRM_ERROR("Panel %d get power mode failed\n", pipe);
966 			dsi_connector->status = connector_status_disconnected;
967 		} else {
968 			DRM_INFO("pipe %d power mode 0x%x\n", pipe, data);
969 			dsi_connector->status = connector_status_connected;
970 		}
971 	}
972 
973 	dpi_output = kzalloc(sizeof(struct mdfld_dsi_dpi_output), GFP_KERNEL);
974 	if (!dpi_output) {
975 		DRM_ERROR("No memory\n");
976 		return NULL;
977 	}
978 
979 	if (dsi_connector->pipe)
980 		dpi_output->panel_on = 0;
981 	else
982 		dpi_output->panel_on = 0;
983 
984 	dpi_output->dev = dev;
985 	if (mdfld_get_panel_type(dev, pipe) != TC35876X)
986 		dpi_output->p_funcs = p_funcs;
987 	dpi_output->first_boot = 1;
988 
989 	/*get fixed mode*/
990 	dsi_config = mdfld_dsi_get_config(dsi_connector);
991 
992 	/*create drm encoder object*/
993 	connector = &dsi_connector->base.base;
994 	encoder = &dpi_output->base.base.base;
995 	drm_encoder_init(dev,
996 			encoder,
997 			p_funcs->encoder_funcs,
998 			DRM_MODE_ENCODER_LVDS);
999 	drm_encoder_helper_add(encoder,
1000 				p_funcs->encoder_helper_funcs);
1001 
1002 	/*attach to given connector*/
1003 	drm_mode_connector_attach_encoder(connector, encoder);
1004 
1005 	/*set possible crtcs and clones*/
1006 	if (dsi_connector->pipe) {
1007 		encoder->possible_crtcs = (1 << 2);
1008 		encoder->possible_clones = (1 << 1);
1009 	} else {
1010 		encoder->possible_crtcs = (1 << 0);
1011 		encoder->possible_clones = (1 << 0);
1012 	}
1013 
1014 	dsi_connector->base.encoder = &dpi_output->base.base;
1015 
1016 	return &dpi_output->base;
1017 }
1018