Home
last modified time | relevance | path

Searched refs:USB (Results 1 – 25 of 212) sorted by relevance

123456789

/arch/arm/boot/dts/
Dusb_a9g20.dts2 * usb_a9g20.dts - Device Tree file for Caloa USB A9G20 board
12 model = "Calao USB A9G20";
Dusb_a9260.dts2 * usb_a9260.dts - Device Tree file for Caloa USB A9260 board
13 model = "Calao USB A9260";
Dusb_a9g20_lpw.dts2 * usb_a9g20_lpw.dts - Device Tree file for Caloa USB A9G20 Low Power board
12 model = "Calao USB A9G20 Low Power";
Dkirkwood-ts219-6281.dts20 pmx_USB_copy_button: pmx-USB-copy-button {
44 label = "USB Copy";
Dkirkwood-ts219-6282.dts24 pmx_USB_copy_button: pmx-USB-copy-button {
44 label = "USB Copy";
Dorion5x-rd88f5182-nas.dts136 * MPP[22] USB 0 over current indication
137 * MPP[23] USB 1 over current indication
138 * MPP[24] USB 1 over current enable
139 * MPP[25] USB 0 over current enable
Dsun4i-a10-pcduino2.dts46 * is that the pcDuino2 board got a USB VBUS voltage regulator, which
48 * the USB host ports has been replaced with a USB WIFI chip.
73 usb1_vbus-supply = <&reg_vcc3v3>; /* USB WIFI is always on */
Dkirkwood-ts419.dtsi20 pmx_USB_copy_button: pmx-USB-copy-button {
49 label = "USB Copy";
Darmada-370-seagate-personal-cloud.dtsi67 regulator-name = "USB Power";
105 label = "USB VBUS error";
131 /* USB 3.0 Bridge ASM1042A */
Dkirkwood-laplug.dts92 regulator-name = "USB Power Back 1";
104 regulator-name = "USB Power Back 2";
116 regulator-name = "USB Power Front";
Dusb_a9g20_common.dtsi2 * usb_a9g20.dts - Device Tree file for Caloa USB A9G20 board
Domap3-beagle-xm-ab.dts12 /* HS USB Port 2 Power enable was inverted with the xM C */
Dusb_a9263.dts2 * usb_a9263.dts - Device Tree file for Caloa USB A9293 board
12 model = "Calao USB A9263";
Dimx6q-gk802.dts148 /* External USB-A port (USBOTG) */
154 /* Internal USB port (USBH1), connected to RTL8192CU */
Domap3-cm-t3x.dtsi24 /* HS USB Port 1 Power */
33 /* HS USB Port 2 Power */
42 /* HS USB Host PHY on PORT 1 */
48 /* HS USB Host PHY on PORT 2 */
Domap3-sbc-t3530.dts25 OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
Domap3-sbc-t3730.dts25 OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */
/arch/sh/kernel/cpu/sh3/
Dsetup-sh7705.c28 DMAC, SCIF0, SCIF2, ADC_ADI, USB, enumerator
46 INTC_VECT(USB, 0xa20), INTC_VECT(USB, 0xa40),
63 { 0xa4080000, 0, 16, 4, /* IPRF */ { 0, 0, USB } },
/arch/arm/mach-cns3xxx/
DKconfig18 for USB, USB-OTG, MMC/SD/SDIO, SATA, PCI-E, etc.
/arch/powerpc/platforms/embedded6xx/
DKconfig93 bool "USB Gecko udbg console for the Nintendo GameCube/Wii"
97 USB Gecko adapter as an udbg console.
98 The USB Gecko is a EXI to USB Serial converter that can be plugged
/arch/sh/kernel/cpu/sh4/
Dsetup-sh7760.c29 USB, LCDC, enumerator
58 INTC_VECT(USB, 0xa00), INTC_VECT(LCDC, 0xa20),
92 SSI0, SSI1, HAC0, HAC1, I2C0, I2C1, USB, LCDC,
113 { 0xfe080008, 0, 32, 4, /* INTPRI08 */ { USB, LCDC, DMABRG, SCIF0,
/arch/sh/kernel/cpu/sh4a/
Dsetup-sh7366.c260 MFI, VPU, USB, enumerator
286 INTC_VECT(MFI, 0x900), INTC_VECT(VPU, 0x980), INTC_VECT(USB, 0xa20),
338 { 0, 0, 0, CMT, 0, USB, } },
353 { 0xa4080014, 0, 16, 4, /* IPRF */ { 0, DMAC45, USB, CMT } },
/arch/arm64/boot/dts/amlogic/
Dmeson-gxbb-odroidc2.dts167 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
168 * to be turned high in order to be detected by the USB Controller
169 * This signal should be handled by a USB specific power sequence
170 * in order to reset the Hub when USB bus is powered down.
194 "USB HUB nRESET", "USB OTG Power En",
/arch/mips/boot/dts/brcm/
Dbcm97125cbmb.dts53 /* FIXME: USB is wonky; disable it for now */
/arch/sh/drivers/dma/
DKconfig47 The DMABRG does data transfers from main memory to Audio/USB units
49 Say Y if you want to use Audio/USB DMA on your SH7760 board.

123456789