Home
last modified time | relevance | path

Searched refs:systems (Results 1 – 25 of 91) sorted by relevance

1234

/drivers/media/platform/marvell-ccic/
DKconfig12 generation OLPC systems.
25 in OLPC XO 1.75 systems.
/drivers/ntb/
DKconfig6 connecting 2 systems. When configured, writes to the device's PCI
22 This is a transport driver that enables connected systems to exchange
/drivers/firmware/
DKconfig107 tristate "BIOS update support for DELL systems via sysfs"
123 for systems management software to perform System Management
125 power off after OS shutdown) on certain Dell systems.
128 and the Dell systems on which Dell systems management software makes
131 Say Y or M here to enable the driver for use by Dell systems
224 compute systems such as ARM, DSP etc with the system controller in
/drivers/net/ethernet/ibm/
DKconfig24 and pSeries systems.
45 systems.
/drivers/pnp/pnpbios/
DKconfig17 your mainboard devices (on some systems they are disabled by the
34 Also some buggy systems will fault when accessing certain features
/drivers/thermal/tegra/
DKconfig8 Tegra systems-on-chip. The driver supports four thermal zones
/drivers/net/ethernet/sun/
DKconfig25 systems and as an option on older Sbus systems. This driver supports
/drivers/cpuidle/
DKconfig.mips14 through cpuidle for systems built around the MIPS Coherent
/drivers/base/
DKconfig13 This should not be used today, because usual systems create
16 that it creates a high system load, or on smaller systems
43 rescue systems, and reliably handles dynamic major/minor numbers.
180 Say 'N' for more sensitive systems or systems that don't want
/drivers/staging/pi433/
DKconfig10 communicate between two systems without using ethernet or bluetooth
/drivers/mtd/lpddr/
DKconfig10 DDR memories, intended for battery-operated systems.
/drivers/misc/cxl/
DKconfig33 CAPI adapters are found in POWER8 based systems.
/drivers/perf/
DKconfig14 systems.
/drivers/rpmsg/
DKconfig28 enabled systems.
/drivers/tty/
DKconfig89 terminal through console drivers. On these systems, at least one
120 All modern Linux systems use the Unix98 ptys. Say Y unless
138 systems, it is safe to say N.
149 systems may want to reduce this to save memory.
174 Digiboards, etc. These are usually used for systems that need many
478 means. This is not always the best thing to do on systems
/drivers/block/
DKconfig208 file systems). If you want to use the cryptoloop, say Y to both
246 WARNING: This device is not safe for journaled file systems like
259 servers (mount file systems on them etc.). Communication between
272 Note that this has nothing to do with the network file systems NFS
304 a block device, so that you can make file systems on it, read and
346 allocated from highmem (only a problem for highmem systems).
/drivers/memstick/core/
DKconfig16 This option is usually just for embedded systems which use
/drivers/pps/
DKconfig38 It doesn't work on tickless systems at the moment.
/drivers/staging/lustre/lustre/
DKconfig20 To mount Lustre file systems, you also need to install the user space
/drivers/pcmcia/
DKconfig133 older laptops and ISA-bus card readers for desktop systems. A
143 host bridges. These are only found on a handful of old systems.
162 systems.
/drivers/usb/typec/ucsi/
DKconfig11 is required. UCSI is available on most of the new Intel based systems
/drivers/cpufreq/
DKconfig.x86201 mobile Intel Pentium 4 P4-M on systems which have an Intel ICH2,
214 on systems which have an Intel 440BX/ZX/MX southbridge.
295 normally be done. Some ancient or strange systems, though speedstep
/drivers/video/fbdev/omap/
DKconfig55 On systems in which video memory is in system memory
/drivers/net/wireless/ath/
DKconfig53 Say N. This should only be enabled on systems
/drivers/net/ethernet/amd/
DKconfig167 systems, on some older Ultra systems and as an Sbus option. These

1234