1menu "SCSI device support" 2 3config SCSI_MOD 4 tristate 5 default y if SCSI=n || SCSI=y 6 default m if SCSI=m 7 8config RAID_ATTRS 9 tristate "RAID Transport Class" 10 default n 11 depends on BLOCK 12 depends on SCSI_MOD 13 ---help--- 14 Provides RAID 15 16config SCSI 17 tristate "SCSI device support" 18 depends on BLOCK 19 select SCSI_DMA if HAS_DMA 20 ---help--- 21 If you want to use a SCSI hard disk, SCSI tape drive, SCSI CD-ROM or 22 any other SCSI device under Linux, say Y and make sure that you know 23 the name of your SCSI host adapter (the card inside your computer 24 that "speaks" the SCSI protocol, also called SCSI controller), 25 because you will be asked for it. 26 27 You also need to say Y here if you have a device which speaks 28 the SCSI protocol. Examples of this include the parallel port 29 version of the IOMEGA ZIP drive, USB storage devices, Fibre 30 Channel, and FireWire storage. 31 32 To compile this driver as a module, choose M here and read 33 <file:Documentation/scsi/scsi.txt>. 34 The module will be called scsi_mod. 35 36 However, do not compile this as a module if your root file system 37 (the one containing the directory /) is located on a SCSI device. 38 39config SCSI_DMA 40 bool 41 default n 42 43config SCSI_NETLINK 44 bool 45 default n 46 depends on NET 47 48config SCSI_MQ_DEFAULT 49 bool "SCSI: use blk-mq I/O path by default" 50 depends on SCSI 51 ---help--- 52 This option enables the new blk-mq based I/O path for SCSI 53 devices by default. With the option the scsi_mod.use_blk_mq 54 module/boot option defaults to Y, without it to N, but it can 55 still be overridden either way. 56 57 If unsure say N. 58 59config SCSI_PROC_FS 60 bool "legacy /proc/scsi/ support" 61 depends on SCSI && PROC_FS 62 default y 63 ---help--- 64 This option enables support for the various files in 65 /proc/scsi. In Linux 2.6 this has been superseded by 66 files in sysfs but many legacy applications rely on this. 67 68 If unsure say Y. 69 70comment "SCSI support type (disk, tape, CD-ROM)" 71 depends on SCSI 72 73config BLK_DEV_SD 74 tristate "SCSI disk support" 75 depends on SCSI 76 ---help--- 77 If you want to use SCSI hard disks, Fibre Channel disks, 78 Serial ATA (SATA) or Parallel ATA (PATA) hard disks, 79 USB storage or the SCSI or parallel port version of 80 the IOMEGA ZIP drive, say Y and read the SCSI-HOWTO, 81 the Disk-HOWTO and the Multi-Disk-HOWTO, available from 82 <http://www.tldp.org/docs.html#howto>. This is NOT for SCSI 83 CD-ROMs. 84 85 To compile this driver as a module, choose M here and read 86 <file:Documentation/scsi/scsi.txt>. 87 The module will be called sd_mod. 88 89 Do not compile this driver as a module if your root file system 90 (the one containing the directory /) is located on a SCSI disk. 91 In this case, do not compile the driver for your SCSI host adapter 92 (below) as a module either. 93 94config CHR_DEV_ST 95 tristate "SCSI tape support" 96 depends on SCSI 97 ---help--- 98 If you want to use a SCSI tape drive under Linux, say Y and read the 99 SCSI-HOWTO, available from 100 <http://www.tldp.org/docs.html#howto>, and 101 <file:Documentation/scsi/st.txt> in the kernel source. This is NOT 102 for SCSI CD-ROMs. 103 104 To compile this driver as a module, choose M here and read 105 <file:Documentation/scsi/scsi.txt>. The module will be called st. 106 107config CHR_DEV_OSST 108 tristate "SCSI OnStream SC-x0 tape support" 109 depends on SCSI 110 ---help--- 111 The OnStream SC-x0 SCSI tape drives cannot be driven by the 112 standard st driver, but instead need this special osst driver and 113 use the /dev/osstX char device nodes (major 206). Via usb-storage, 114 you may be able to drive the USB-x0 and DI-x0 drives as well. 115 Note that there is also a second generation of OnStream 116 tape drives (ADR-x0) that supports the standard SCSI-2 commands for 117 tapes (QIC-157) and can be driven by the standard driver st. 118 For more information, you may have a look at the SCSI-HOWTO 119 <http://www.tldp.org/docs.html#howto> and 120 <file:Documentation/scsi/osst.txt> in the kernel source. 121 More info on the OnStream driver may be found on 122 <http://sourceforge.net/projects/osst/> 123 Please also have a look at the standard st docu, as most of it 124 applies to osst as well. 125 126 To compile this driver as a module, choose M here and read 127 <file:Documentation/scsi/scsi.txt>. The module will be called osst. 128 129config BLK_DEV_SR 130 tristate "SCSI CDROM support" 131 depends on SCSI 132 ---help--- 133 If you want to use a CD or DVD drive attached to your computer 134 by SCSI, FireWire, USB or ATAPI, say Y and read the SCSI-HOWTO 135 and the CDROM-HOWTO at <http://www.tldp.org/docs.html#howto>. 136 137 Make sure to say Y or M to "ISO 9660 CD-ROM file system support". 138 139 To compile this driver as a module, choose M here and read 140 <file:Documentation/scsi/scsi.txt>. 141 The module will be called sr_mod. 142 143config BLK_DEV_SR_VENDOR 144 bool "Enable vendor-specific extensions (for SCSI CDROM)" 145 depends on BLK_DEV_SR 146 help 147 This enables the usage of vendor specific SCSI commands. This is 148 required to support multisession CDs with old NEC/TOSHIBA cdrom 149 drives (and HP Writers). If you have such a drive and get the first 150 session only, try saying Y here; everybody else says N. 151 152config CHR_DEV_SG 153 tristate "SCSI generic support" 154 depends on SCSI 155 ---help--- 156 If you want to use SCSI scanners, synthesizers or CD-writers or just 157 about anything having "SCSI" in its name other than hard disks, 158 CD-ROMs or tapes, say Y here. These won't be supported by the kernel 159 directly, so you need some additional software which knows how to 160 talk to these devices using the SCSI protocol: 161 162 For scanners, look at SANE (<http://www.sane-project.org/>). For CD 163 writer software look at Cdrtools 164 (<http://cdrecord.berlios.de/private/cdrecord.html>) 165 and for burning a "disk at once": CDRDAO 166 (<http://cdrdao.sourceforge.net/>). Cdparanoia is a high 167 quality digital reader of audio CDs (<http://www.xiph.org/paranoia/>). 168 For other devices, it's possible that you'll have to write the 169 driver software yourself. Please read the file 170 <file:Documentation/scsi/scsi-generic.txt> for more information. 171 172 To compile this driver as a module, choose M here and read 173 <file:Documentation/scsi/scsi.txt>. The module will be called sg. 174 175 If unsure, say N. 176 177config CHR_DEV_SCH 178 tristate "SCSI media changer support" 179 depends on SCSI 180 ---help--- 181 This is a driver for SCSI media changers. Most common devices are 182 tape libraries and MOD/CDROM jukeboxes. *Real* jukeboxes, you 183 don't need this for those tiny 6-slot cdrom changers. Media 184 changers are listed as "Type: Medium Changer" in /proc/scsi/scsi. 185 If you have such hardware and want to use it with linux, say Y 186 here. Check <file:Documentation/scsi/scsi-changer.txt> for details. 187 188 If you want to compile this as a module ( = code which can be 189 inserted in and removed from the running kernel whenever you want), 190 say M here and read <file:Documentation/kbuild/modules.txt> and 191 <file:Documentation/scsi/scsi.txt>. The module will be called ch.o. 192 If unsure, say N. 193 194config SCSI_ENCLOSURE 195 tristate "SCSI Enclosure Support" 196 depends on SCSI && ENCLOSURE_SERVICES 197 help 198 Enclosures are devices sitting on or in SCSI backplanes that 199 manage devices. If you have a disk cage, the chances are that 200 it has an enclosure device. Selecting this option will just allow 201 certain enclosure conditions to be reported and is not required. 202 203config SCSI_CONSTANTS 204 bool "Verbose SCSI error reporting (kernel size +=75K)" 205 depends on SCSI 206 help 207 The error messages regarding your SCSI hardware will be easier to 208 understand if you say Y here; it will enlarge your kernel by about 209 75 KB. If in doubt, say Y. 210 211config SCSI_LOGGING 212 bool "SCSI logging facility" 213 depends on SCSI 214 ---help--- 215 This turns on a logging facility that can be used to debug a number 216 of SCSI related problems. 217 218 If you say Y here, no logging output will appear by default, but you 219 can enable logging by saying Y to "/proc file system support" and 220 "Sysctl support" below and executing the command 221 222 echo <bitmask> > /proc/sys/dev/scsi/logging_level 223 224 where <bitmask> is a four byte value representing the logging type 225 and logging level for each type of logging selected. 226 227 There are a number of logging types and you can find them in the 228 source at <file:drivers/scsi/scsi_logging.h>. The logging levels 229 are also described in that file and they determine the verbosity of 230 the logging for each logging type. 231 232 If you say N here, it may be harder to track down some types of SCSI 233 problems. If you say Y here your kernel will be somewhat larger, but 234 there should be no noticeable performance impact as long as you have 235 logging turned off. 236 237config SCSI_SCAN_ASYNC 238 bool "Asynchronous SCSI scanning" 239 depends on SCSI 240 help 241 The SCSI subsystem can probe for devices while the rest of the 242 system continues booting, and even probe devices on different 243 busses in parallel, leading to a significant speed-up. 244 245 You can override this choice by specifying "scsi_mod.scan=sync" 246 or async on the kernel's command line. 247 248 Note that this setting also affects whether resuming from 249 system suspend will be performed asynchronously. 250 251menu "SCSI Transports" 252 depends on SCSI 253 254config SCSI_SPI_ATTRS 255 tristate "Parallel SCSI (SPI) Transport Attributes" 256 depends on SCSI 257 help 258 If you wish to export transport-specific information about 259 each attached SCSI device to sysfs, say Y. Otherwise, say N. 260 261config SCSI_FC_ATTRS 262 tristate "FiberChannel Transport Attributes" 263 depends on SCSI && NET 264 select SCSI_NETLINK 265 help 266 If you wish to export transport-specific information about 267 each attached FiberChannel device to sysfs, say Y. 268 Otherwise, say N. 269 270config SCSI_ISCSI_ATTRS 271 tristate "iSCSI Transport Attributes" 272 depends on SCSI && NET 273 select BLK_DEV_BSGLIB 274 help 275 If you wish to export transport-specific information about 276 each attached iSCSI device to sysfs, say Y. 277 Otherwise, say N. 278 279config SCSI_SAS_ATTRS 280 tristate "SAS Transport Attributes" 281 depends on SCSI 282 select BLK_DEV_BSG 283 help 284 If you wish to export transport-specific information about 285 each attached SAS device to sysfs, say Y. 286 287source "drivers/scsi/libsas/Kconfig" 288 289config SCSI_SRP_ATTRS 290 tristate "SRP Transport Attributes" 291 depends on SCSI 292 help 293 If you wish to export transport-specific information about 294 each attached SRP device to sysfs, say Y. 295 296endmenu 297 298menuconfig SCSI_LOWLEVEL 299 bool "SCSI low-level drivers" 300 depends on SCSI!=n 301 default y 302 303if SCSI_LOWLEVEL && SCSI 304 305config ISCSI_TCP 306 tristate "iSCSI Initiator over TCP/IP" 307 depends on SCSI && INET 308 select CRYPTO 309 select CRYPTO_MD5 310 select CRYPTO_CRC32C 311 select SCSI_ISCSI_ATTRS 312 help 313 The iSCSI Driver provides a host with the ability to access storage 314 through an IP network. The driver uses the iSCSI protocol to transport 315 SCSI requests and responses over a TCP/IP network between the host 316 (the "initiator") and "targets". Architecturally, the iSCSI driver 317 combines with the host's TCP/IP stack, network drivers, and Network 318 Interface Card (NIC) to provide the same functions as a SCSI or a 319 Fibre Channel (FC) adapter driver with a Host Bus Adapter (HBA). 320 321 To compile this driver as a module, choose M here: the 322 module will be called iscsi_tcp. 323 324 The userspace component needed to initialize the driver, documentation, 325 and sample configuration files can be found here: 326 327 http://open-iscsi.org 328 329config ISCSI_BOOT_SYSFS 330 tristate "iSCSI Boot Sysfs Interface" 331 default n 332 help 333 This option enables support for exposing iSCSI boot information 334 via sysfs to userspace. If you wish to export this information, 335 say Y. Otherwise, say N. 336 337source "drivers/scsi/cxgbi/Kconfig" 338source "drivers/scsi/bnx2i/Kconfig" 339source "drivers/scsi/bnx2fc/Kconfig" 340source "drivers/scsi/be2iscsi/Kconfig" 341source "drivers/scsi/cxlflash/Kconfig" 342 343config SGIWD93_SCSI 344 tristate "SGI WD93C93 SCSI Driver" 345 depends on SGI_HAS_WD93 && SCSI 346 help 347 If you have a Western Digital WD93 SCSI controller on 348 an SGI MIPS system, say Y. Otherwise, say N. 349 350config BLK_DEV_3W_XXXX_RAID 351 tristate "3ware 5/6/7/8xxx ATA-RAID support" 352 depends on PCI && SCSI 353 help 354 3ware is the only hardware ATA-Raid product in Linux to date. 355 This card is 2,4, or 8 channel master mode support only. 356 SCSI support required!!! 357 358 <http://www.3ware.com/> 359 360 Please read the comments at the top of 361 <file:drivers/scsi/3w-xxxx.c>. 362 363config SCSI_HPSA 364 tristate "HP Smart Array SCSI driver" 365 depends on PCI && SCSI 366 select CHECK_SIGNATURE 367 select SCSI_SAS_ATTRS 368 help 369 This driver supports HP Smart Array Controllers (circa 2009). 370 It is a SCSI alternative to the cciss driver, which is a block 371 driver. Anyone wishing to use HP Smart Array controllers who 372 would prefer the devices be presented to linux as SCSI devices, 373 rather than as generic block devices should say Y here. 374 375config SCSI_3W_9XXX 376 tristate "3ware 9xxx SATA-RAID support" 377 depends on PCI && SCSI 378 help 379 This driver supports the 9000 series 3ware SATA-RAID cards. 380 381 <http://www.amcc.com> 382 383 Please read the comments at the top of 384 <file:drivers/scsi/3w-9xxx.c>. 385 386config SCSI_3W_SAS 387 tristate "3ware 97xx SAS/SATA-RAID support" 388 depends on PCI && SCSI 389 help 390 This driver supports the LSI 3ware 9750 6Gb/s SAS/SATA-RAID cards. 391 392 <http://www.lsi.com> 393 394 Please read the comments at the top of 395 <file:drivers/scsi/3w-sas.c>. 396 397config SCSI_7000FASST 398 tristate "7000FASST SCSI support" 399 depends on ISA && SCSI && ISA_DMA_API 400 select CHECK_SIGNATURE 401 help 402 This driver supports the Western Digital 7000 SCSI host adapter 403 family. Some information is in the source: 404 <file:drivers/scsi/wd7000.c>. 405 406 To compile this driver as a module, choose M here: the 407 module will be called wd7000. 408 409config SCSI_ACARD 410 tristate "ACARD SCSI support" 411 depends on PCI && SCSI 412 help 413 This driver supports the ACARD SCSI host adapter. 414 Support Chip <ATP870 ATP876 ATP880 ATP885> 415 To compile this driver as a module, choose M here: the 416 module will be called atp870u. 417 418config SCSI_AHA152X 419 tristate "Adaptec AHA152X/2825 support" 420 depends on ISA && SCSI 421 select SCSI_SPI_ATTRS 422 select CHECK_SIGNATURE 423 ---help--- 424 This is a driver for the AHA-1510, AHA-1520, AHA-1522, and AHA-2825 425 SCSI host adapters. It also works for the AVA-1505, but the IRQ etc. 426 must be manually specified in this case. 427 428 It is explained in section 3.3 of the SCSI-HOWTO, available from 429 <http://www.tldp.org/docs.html#howto>. You might also want to 430 read the file <file:Documentation/scsi/aha152x.txt>. 431 432 To compile this driver as a module, choose M here: the 433 module will be called aha152x. 434 435config SCSI_AHA1542 436 tristate "Adaptec AHA1542 support" 437 depends on ISA && SCSI && ISA_DMA_API 438 ---help--- 439 This is support for a SCSI host adapter. It is explained in section 440 3.4 of the SCSI-HOWTO, available from 441 <http://www.tldp.org/docs.html#howto>. Note that Trantor was 442 purchased by Adaptec, and some former Trantor products are being 443 sold under the Adaptec name. If it doesn't work out of the box, you 444 may have to change some settings in <file:drivers/scsi/aha1542.h>. 445 446 To compile this driver as a module, choose M here: the 447 module will be called aha1542. 448 449config SCSI_AHA1740 450 tristate "Adaptec AHA1740 support" 451 depends on EISA && SCSI 452 ---help--- 453 This is support for a SCSI host adapter. It is explained in section 454 3.5 of the SCSI-HOWTO, available from 455 <http://www.tldp.org/docs.html#howto>. If it doesn't work out 456 of the box, you may have to change some settings in 457 <file:drivers/scsi/aha1740.h>. 458 459 To compile this driver as a module, choose M here: the 460 module will be called aha1740. 461 462config SCSI_AACRAID 463 tristate "Adaptec AACRAID support" 464 depends on SCSI && PCI 465 help 466 This driver supports a variety of Dell, HP, Adaptec, IBM and 467 ICP storage products. For a list of supported products, refer 468 to <file:Documentation/scsi/aacraid.txt>. 469 470 To compile this driver as a module, choose M here: the module 471 will be called aacraid. 472 473 474source "drivers/scsi/aic7xxx/Kconfig.aic7xxx" 475source "drivers/scsi/aic7xxx/Kconfig.aic79xx" 476source "drivers/scsi/aic94xx/Kconfig" 477source "drivers/scsi/mvsas/Kconfig" 478 479config SCSI_MVUMI 480 tristate "Marvell UMI driver" 481 depends on SCSI && PCI 482 help 483 Module for Marvell Universal Message Interface(UMI) driver 484 485 To compile this driver as a module, choose M here: the 486 module will be called mvumi. 487 488config SCSI_DPT_I2O 489 tristate "Adaptec I2O RAID support " 490 depends on SCSI && PCI && VIRT_TO_BUS 491 help 492 This driver supports all of Adaptec's I2O based RAID controllers as 493 well as the DPT SmartRaid V cards. This is an Adaptec maintained 494 driver by Deanna Bonds. See <file:Documentation/scsi/dpti.txt>. 495 496 To compile this driver as a module, choose M here: the 497 module will be called dpt_i2o. 498 499config SCSI_ADVANSYS 500 tristate "AdvanSys SCSI support" 501 depends on SCSI 502 depends on ISA || EISA || PCI 503 depends on ISA_DMA_API || !ISA 504 help 505 This is a driver for all SCSI host adapters manufactured by 506 AdvanSys. It is documented in the kernel source in 507 <file:drivers/scsi/advansys.c>. 508 509 To compile this driver as a module, choose M here: the 510 module will be called advansys. 511 512config SCSI_IN2000 513 tristate "Always IN2000 SCSI support" 514 depends on ISA && SCSI 515 help 516 This is support for an ISA bus SCSI host adapter. You'll find more 517 information in <file:Documentation/scsi/in2000.txt>. If it doesn't work 518 out of the box, you may have to change the jumpers for IRQ or 519 address selection. 520 521 To compile this driver as a module, choose M here: the 522 module will be called in2000. 523 524config SCSI_ARCMSR 525 tristate "ARECA (ARC11xx/12xx/13xx/16xx) SATA/SAS RAID Host Adapter" 526 depends on PCI && SCSI 527 help 528 This driver supports all of ARECA's SATA/SAS RAID controller cards. 529 This is an ARECA-maintained driver by Erich Chen. 530 If you have any problems, please mail to: <erich@areca.com.tw>. 531 Areca supports Linux RAID config tools. 532 Please link <http://www.areca.com.tw> 533 534 To compile this driver as a module, choose M here: the 535 module will be called arcmsr (modprobe arcmsr). 536 537source "drivers/scsi/esas2r/Kconfig" 538source "drivers/scsi/megaraid/Kconfig.megaraid" 539source "drivers/scsi/mpt3sas/Kconfig" 540source "drivers/scsi/ufs/Kconfig" 541 542config SCSI_HPTIOP 543 tristate "HighPoint RocketRAID 3xxx/4xxx Controller support" 544 depends on SCSI && PCI 545 help 546 This option enables support for HighPoint RocketRAID 3xxx/4xxx 547 controllers. 548 549 To compile this driver as a module, choose M here; the module 550 will be called hptiop. If unsure, say N. 551 552config SCSI_BUSLOGIC 553 tristate "BusLogic SCSI support" 554 depends on (PCI || ISA || MCA) && SCSI && ISA_DMA_API && VIRT_TO_BUS 555 ---help--- 556 This is support for BusLogic MultiMaster and FlashPoint SCSI Host 557 Adapters. Consult the SCSI-HOWTO, available from 558 <http://www.tldp.org/docs.html#howto>, and the files 559 <file:Documentation/scsi/BusLogic.txt> and 560 <file:Documentation/scsi/FlashPoint.txt> for more information. 561 Note that support for FlashPoint is only available for 32-bit 562 x86 configurations. 563 564 To compile this driver as a module, choose M here: the 565 module will be called BusLogic. 566 567config SCSI_FLASHPOINT 568 bool "FlashPoint support" 569 depends on SCSI_BUSLOGIC && PCI 570 help 571 This option allows you to add FlashPoint support to the 572 BusLogic SCSI driver. The FlashPoint SCCB Manager code is 573 substantial, so users of MultiMaster Host Adapters may not 574 wish to include it. 575 576config VMWARE_PVSCSI 577 tristate "VMware PVSCSI driver support" 578 depends on PCI && SCSI && X86 579 help 580 This driver supports VMware's para virtualized SCSI HBA. 581 To compile this driver as a module, choose M here: the 582 module will be called vmw_pvscsi. 583 584config XEN_SCSI_FRONTEND 585 tristate "XEN SCSI frontend driver" 586 depends on SCSI && XEN 587 select XEN_XENBUS_FRONTEND 588 help 589 The XEN SCSI frontend driver allows the kernel to access SCSI Devices 590 within another guest OS (usually Dom0). 591 Only needed if the kernel is running in a XEN guest and generic 592 SCSI access to a device is needed. 593 594config HYPERV_STORAGE 595 tristate "Microsoft Hyper-V virtual storage driver" 596 depends on SCSI && HYPERV 597 default HYPERV 598 help 599 Select this option to enable the Hyper-V virtual storage driver. 600 601config LIBFC 602 tristate "LibFC module" 603 depends on SCSI_FC_ATTRS 604 select CRC32 605 ---help--- 606 Fibre Channel library module 607 608config LIBFCOE 609 tristate "LibFCoE module" 610 depends on LIBFC 611 ---help--- 612 Library for Fibre Channel over Ethernet module 613 614config FCOE 615 tristate "FCoE module" 616 depends on PCI 617 depends on LIBFCOE 618 ---help--- 619 Fibre Channel over Ethernet module 620 621config FCOE_FNIC 622 tristate "Cisco FNIC Driver" 623 depends on PCI && X86 624 depends on LIBFCOE 625 help 626 This is support for the Cisco PCI-Express FCoE HBA. 627 628 To compile this driver as a module, choose M here and read 629 <file:Documentation/scsi/scsi.txt>. 630 The module will be called fnic. 631 632config SCSI_SNIC 633 tristate "Cisco SNIC Driver" 634 depends on PCI && SCSI 635 help 636 This is support for the Cisco PCI-Express SCSI HBA. 637 638 To compile this driver as a module, choose M here and read 639 <file:Documentation/scsi/scsi.txt>. 640 The module will be called snic. 641 642config SCSI_SNIC_DEBUG_FS 643 bool "Cisco SNIC Driver Debugfs Support" 644 depends on SCSI_SNIC && DEBUG_FS 645 help 646 This enables to list debugging information from SNIC Driver 647 available via debugfs file system 648 649config SCSI_DMX3191D 650 tristate "DMX3191D SCSI support" 651 depends on PCI && SCSI 652 select SCSI_SPI_ATTRS 653 help 654 This is support for Domex DMX3191D SCSI Host Adapters. 655 656 To compile this driver as a module, choose M here: the 657 module will be called dmx3191d. 658 659config SCSI_DTC3280 660 tristate "DTC3180/3280 SCSI support" 661 depends on ISA && SCSI 662 select SCSI_SPI_ATTRS 663 select CHECK_SIGNATURE 664 help 665 This is support for DTC 3180/3280 SCSI Host Adapters. Please read 666 the SCSI-HOWTO, available from 667 <http://www.tldp.org/docs.html#howto>, and the file 668 <file:Documentation/scsi/dtc3x80.txt>. 669 670 To compile this driver as a module, choose M here: the 671 module will be called dtc. 672 673config SCSI_EATA 674 tristate "EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards) support" 675 depends on (ISA || EISA || PCI) && SCSI && ISA_DMA_API 676 ---help--- 677 This driver supports all EATA/DMA-compliant SCSI host adapters. DPT 678 ISA and all EISA I/O addresses are probed looking for the "EATA" 679 signature. The addresses of all the PCI SCSI controllers reported 680 by the PCI subsystem are probed as well. 681 682 You want to read the start of <file:drivers/scsi/eata.c> and the 683 SCSI-HOWTO, available from 684 <http://www.tldp.org/docs.html#howto>. 685 686 To compile this driver as a module, choose M here: the 687 module will be called eata. 688 689config SCSI_EATA_TAGGED_QUEUE 690 bool "enable tagged command queueing" 691 depends on SCSI_EATA 692 help 693 This is a feature of SCSI-2 which improves performance: the host 694 adapter can send several SCSI commands to a device's queue even if 695 previous commands haven't finished yet. 696 This is equivalent to the "eata=tc:y" boot option. 697 698config SCSI_EATA_LINKED_COMMANDS 699 bool "enable elevator sorting" 700 depends on SCSI_EATA 701 help 702 This option enables elevator sorting for all probed SCSI disks and 703 CD-ROMs. It definitely reduces the average seek distance when doing 704 random seeks, but this does not necessarily result in a noticeable 705 performance improvement: your mileage may vary... 706 This is equivalent to the "eata=lc:y" boot option. 707 708config SCSI_EATA_MAX_TAGS 709 int "maximum number of queued commands" 710 depends on SCSI_EATA 711 default "16" 712 help 713 This specifies how many SCSI commands can be maximally queued for 714 each probed SCSI device. You should reduce the default value of 16 715 only if you have disks with buggy or limited tagged command support. 716 Minimum is 2 and maximum is 62. This value is also the window size 717 used by the elevator sorting option above. The effective value used 718 by the driver for each probed SCSI device is reported at boot time. 719 This is equivalent to the "eata=mq:8" boot option. 720 721config SCSI_EATA_PIO 722 tristate "EATA-PIO (old DPT PM2001, PM2012A) support" 723 depends on (ISA || EISA || PCI) && SCSI && BROKEN 724 ---help--- 725 This driver supports all EATA-PIO protocol compliant SCSI Host 726 Adapters like the DPT PM2001 and the PM2012A. EATA-DMA compliant 727 host adapters could also use this driver but are discouraged from 728 doing so, since this driver only supports hard disks and lacks 729 numerous features. You might want to have a look at the SCSI-HOWTO, 730 available from <http://www.tldp.org/docs.html#howto>. 731 732 To compile this driver as a module, choose M here: the 733 module will be called eata_pio. 734 735config SCSI_FUTURE_DOMAIN 736 tristate "Future Domain 16xx SCSI/AHA-2920A support" 737 depends on (ISA || PCI) && SCSI 738 select CHECK_SIGNATURE 739 ---help--- 740 This is support for Future Domain's 16-bit SCSI host adapters 741 (TMC-1660/1680, TMC-1650/1670, TMC-3260, TMC-1610M/MER/MEX) and 742 other adapters based on the Future Domain chipsets (Quantum 743 ISA-200S, ISA-250MG; Adaptec AHA-2920A; and at least one IBM board). 744 It is explained in section 3.7 of the SCSI-HOWTO, available from 745 <http://www.tldp.org/docs.html#howto>. 746 747 NOTE: Newer Adaptec AHA-2920C boards use the Adaptec AIC-7850 chip 748 and should use the aic7xxx driver ("Adaptec AIC7xxx chipset SCSI 749 controller support"). This Future Domain driver works with the older 750 Adaptec AHA-2920A boards with a Future Domain chip on them. 751 752 To compile this driver as a module, choose M here: the 753 module will be called fdomain. 754 755config SCSI_GDTH 756 tristate "Intel/ICP (former GDT SCSI Disk Array) RAID Controller support" 757 depends on (ISA || EISA || PCI) && SCSI && ISA_DMA_API 758 ---help--- 759 Formerly called GDT SCSI Disk Array Controller Support. 760 761 This is a driver for RAID/SCSI Disk Array Controllers (EISA/ISA/PCI) 762 manufactured by Intel Corporation/ICP vortex GmbH. It is documented 763 in the kernel source in <file:drivers/scsi/gdth.c> and 764 <file:drivers/scsi/gdth.h>. 765 766 To compile this driver as a module, choose M here: the 767 module will be called gdth. 768 769config SCSI_ISCI 770 tristate "Intel(R) C600 Series Chipset SAS Controller" 771 depends on PCI && SCSI 772 depends on X86 773 select SCSI_SAS_LIBSAS 774 ---help--- 775 This driver supports the 6Gb/s SAS capabilities of the storage 776 control unit found in the Intel(R) C600 series chipset. 777 778config SCSI_GENERIC_NCR5380 779 tristate "Generic NCR5380/53c400 SCSI PIO support" 780 depends on ISA && SCSI 781 select SCSI_SPI_ATTRS 782 ---help--- 783 This is a driver for the old NCR 53c80 series of SCSI controllers 784 on boards using PIO. Most boards such as the Trantor T130 fit this 785 category, along with a large number of ISA 8bit controllers shipped 786 for free with SCSI scanners. If you have a PAS16, T128 or DMX3191 787 you should select the specific driver for that card rather than 788 generic 5380 support. 789 790 It is explained in section 3.8 of the SCSI-HOWTO, available from 791 <http://www.tldp.org/docs.html#howto>. If it doesn't work out 792 of the box, you may have to change some settings in 793 <file:drivers/scsi/g_NCR5380.h>. 794 795 To compile this driver as a module, choose M here: the 796 module will be called g_NCR5380. 797 798config SCSI_GENERIC_NCR5380_MMIO 799 tristate "Generic NCR5380/53c400 SCSI MMIO support" 800 depends on ISA && SCSI 801 select SCSI_SPI_ATTRS 802 ---help--- 803 This is a driver for the old NCR 53c80 series of SCSI controllers 804 on boards using memory mapped I/O. 805 It is explained in section 3.8 of the SCSI-HOWTO, available from 806 <http://www.tldp.org/docs.html#howto>. If it doesn't work out 807 of the box, you may have to change some settings in 808 <file:drivers/scsi/g_NCR5380.h>. 809 810 To compile this driver as a module, choose M here: the 811 module will be called g_NCR5380_mmio. 812 813config SCSI_GENERIC_NCR53C400 814 bool "Enable NCR53c400 extensions" 815 depends on SCSI_GENERIC_NCR5380 816 help 817 This enables certain optimizations for the NCR53c400 SCSI cards. 818 You might as well try it out. Note that this driver will only probe 819 for the Trantor T130B in its default configuration; you might have 820 to pass a command line option to the kernel at boot time if it does 821 not detect your card. See the file 822 <file:Documentation/scsi/g_NCR5380.txt> for details. 823 824config SCSI_IPS 825 tristate "IBM ServeRAID support" 826 depends on PCI && SCSI 827 ---help--- 828 This is support for the IBM ServeRAID hardware RAID controllers. 829 See <http://www.developer.ibm.com/welcome/netfinity/serveraid.html> 830 and <http://www-947.ibm.com/support/entry/portal/docdisplay?brand=5000008&lndocid=SERV-RAID> 831 for more information. If this driver does not work correctly 832 without modification please contact the author by email at 833 <ipslinux@adaptec.com>. 834 835 To compile this driver as a module, choose M here: the 836 module will be called ips. 837 838config SCSI_IBMVSCSI 839 tristate "IBM Virtual SCSI support" 840 depends on PPC_PSERIES 841 select SCSI_SRP_ATTRS 842 help 843 This is the IBM POWER Virtual SCSI Client 844 845 To compile this driver as a module, choose M here: the 846 module will be called ibmvscsi. 847 848config SCSI_IBMVFC 849 tristate "IBM Virtual FC support" 850 depends on PPC_PSERIES && SCSI 851 depends on SCSI_FC_ATTRS 852 help 853 This is the IBM POWER Virtual FC Client 854 855 To compile this driver as a module, choose M here: the 856 module will be called ibmvfc. 857 858config SCSI_IBMVFC_TRACE 859 bool "enable driver internal trace" 860 depends on SCSI_IBMVFC 861 default y 862 help 863 If you say Y here, the driver will trace all commands issued 864 to the adapter. Performance impact is minimal. Trace can be 865 dumped using /sys/class/scsi_host/hostXX/trace. 866 867config SCSI_INITIO 868 tristate "Initio 9100U(W) support" 869 depends on PCI && SCSI 870 help 871 This is support for the Initio 91XXU(W) SCSI host adapter. Please 872 read the SCSI-HOWTO, available from 873 <http://www.tldp.org/docs.html#howto>. 874 875 To compile this driver as a module, choose M here: the 876 module will be called initio. 877 878config SCSI_INIA100 879 tristate "Initio INI-A100U2W support" 880 depends on PCI && SCSI 881 help 882 This is support for the Initio INI-A100U2W SCSI host adapter. 883 Please read the SCSI-HOWTO, available from 884 <http://www.tldp.org/docs.html#howto>. 885 886 To compile this driver as a module, choose M here: the 887 module will be called a100u2w. 888 889config SCSI_PPA 890 tristate "IOMEGA parallel port (ppa - older drives)" 891 depends on SCSI && PARPORT_PC 892 ---help--- 893 This driver supports older versions of IOMEGA's parallel port ZIP 894 drive (a 100 MB removable media device). 895 896 Note that you can say N here if you have the SCSI version of the ZIP 897 drive: it will be supported automatically if you said Y to the 898 generic "SCSI disk support", above. 899 900 If you have the ZIP Plus drive or a more recent parallel port ZIP 901 drive (if the supplied cable with the drive is labeled "AutoDetect") 902 then you should say N here and Y to "IOMEGA parallel port (imm - 903 newer drives)", below. 904 905 For more information about this driver and how to use it you should 906 read the file <file:Documentation/scsi/ppa.txt>. You should also read 907 the SCSI-HOWTO, which is available from 908 <http://www.tldp.org/docs.html#howto>. If you use this driver, 909 you will still be able to use the parallel port for other tasks, 910 such as a printer; it is safe to compile both drivers into the 911 kernel. 912 913 To compile this driver as a module, choose M here: the 914 module will be called ppa. 915 916config SCSI_IMM 917 tristate "IOMEGA parallel port (imm - newer drives)" 918 depends on SCSI && PARPORT_PC 919 ---help--- 920 This driver supports newer versions of IOMEGA's parallel port ZIP 921 drive (a 100 MB removable media device). 922 923 Note that you can say N here if you have the SCSI version of the ZIP 924 drive: it will be supported automatically if you said Y to the 925 generic "SCSI disk support", above. 926 927 If you have the ZIP Plus drive or a more recent parallel port ZIP 928 drive (if the supplied cable with the drive is labeled "AutoDetect") 929 then you should say Y here; if you have an older ZIP drive, say N 930 here and Y to "IOMEGA Parallel Port (ppa - older drives)", above. 931 932 For more information about this driver and how to use it you should 933 read the file <file:Documentation/scsi/ppa.txt>. You should also read 934 the SCSI-HOWTO, which is available from 935 <http://www.tldp.org/docs.html#howto>. If you use this driver, 936 you will still be able to use the parallel port for other tasks, 937 such as a printer; it is safe to compile both drivers into the 938 kernel. 939 940 To compile this driver as a module, choose M here: the 941 module will be called imm. 942 943config SCSI_IZIP_EPP16 944 bool "ppa/imm option - Use slow (but safe) EPP-16" 945 depends on SCSI_PPA || SCSI_IMM 946 ---help--- 947 EPP (Enhanced Parallel Port) is a standard for parallel ports which 948 allows them to act as expansion buses that can handle up to 64 949 peripheral devices. 950 951 Some parallel port chipsets are slower than their motherboard, and 952 so we have to control the state of the chipset's FIFO queue every 953 now and then to avoid data loss. This will be done if you say Y 954 here. 955 956 Generally, saying Y is the safe option and slows things down a bit. 957 958config SCSI_IZIP_SLOW_CTR 959 bool "ppa/imm option - Assume slow parport control register" 960 depends on SCSI_PPA || SCSI_IMM 961 help 962 Some parallel ports are known to have excessive delays between 963 changing the parallel port control register and good data being 964 available on the parallel port data/status register. This option 965 forces a small delay (1.0 usec to be exact) after changing the 966 control register to let things settle out. Enabling this option may 967 result in a big drop in performance but some very old parallel ports 968 (found in 386 vintage machines) will not work properly. 969 970 Generally, saying N is fine. 971 972config SCSI_NCR53C406A 973 tristate "NCR53c406a SCSI support" 974 depends on ISA && SCSI 975 help 976 This is support for the NCR53c406a SCSI host adapter. For user 977 configurable parameters, check out <file:drivers/scsi/NCR53c406a.c> 978 in the kernel source. Also read the SCSI-HOWTO, available from 979 <http://www.tldp.org/docs.html#howto>. 980 981 To compile this driver as a module, choose M here: the 982 module will be called NCR53c406. 983 984config SCSI_NCR_D700 985 tristate "NCR Dual 700 MCA SCSI support" 986 depends on MCA && SCSI 987 select SCSI_SPI_ATTRS 988 help 989 This is a driver for the MicroChannel Dual 700 card produced by 990 NCR and commonly used in 345x/35xx/4100 class machines. It always 991 tries to negotiate sync and uses tag command queueing. 992 993 Unless you have an NCR manufactured machine, the chances are that 994 you do not have this SCSI card, so say N. 995 996config SCSI_LASI700 997 tristate "HP Lasi SCSI support for 53c700/710" 998 depends on GSC && SCSI 999 select SCSI_SPI_ATTRS 1000 help 1001 This is a driver for the SCSI controller in the Lasi chip found in 1002 many PA-RISC workstations & servers. If you do not know whether you 1003 have a Lasi chip, it is safe to say "Y" here. 1004 1005config SCSI_SNI_53C710 1006 tristate "SNI RM SCSI support for 53c710" 1007 depends on SNI_RM && SCSI 1008 select SCSI_SPI_ATTRS 1009 select 53C700_LE_ON_BE 1010 help 1011 This is a driver for the onboard SCSI controller found in older 1012 SNI RM workstations & servers. 1013 1014config 53C700_LE_ON_BE 1015 bool 1016 depends on SCSI_LASI700 || SCSI_SNI_53C710 1017 default y 1018 1019config SCSI_STEX 1020 tristate "Promise SuperTrak EX Series support" 1021 depends on PCI && SCSI 1022 ---help--- 1023 This driver supports Promise SuperTrak EX series storage controllers. 1024 1025 Promise provides Linux RAID configuration utility for these 1026 controllers. Please visit <http://www.promise.com> to download. 1027 1028 To compile this driver as a module, choose M here: the 1029 module will be called stex. 1030 1031config 53C700_BE_BUS 1032 bool 1033 depends on SCSI_A4000T || SCSI_ZORRO7XX || MVME16x_SCSI || BVME6000_SCSI 1034 default y 1035 1036config SCSI_SYM53C8XX_2 1037 tristate "SYM53C8XX Version 2 SCSI support" 1038 depends on PCI && SCSI 1039 select SCSI_SPI_ATTRS 1040 ---help--- 1041 This driver supports the whole NCR53C8XX/SYM53C8XX family of 1042 PCI-SCSI controllers. It also supports the subset of LSI53C10XX 1043 Ultra-160 controllers that are based on the SYM53C8XX SCRIPTS 1044 language. It does not support LSI53C10XX Ultra-320 PCI-X SCSI 1045 controllers; you need to use the Fusion MPT driver for that. 1046 1047 Please read <file:Documentation/scsi/sym53c8xx_2.txt> for more 1048 information. 1049 1050config SCSI_SYM53C8XX_DMA_ADDRESSING_MODE 1051 int "DMA addressing mode" 1052 depends on SCSI_SYM53C8XX_2 1053 default "1" 1054 ---help--- 1055 This option only applies to PCI-SCSI chips that are PCI DAC 1056 capable (875A, 895A, 896, 1010-33, 1010-66, 1000). 1057 1058 When set to 0, the driver will program the chip to only perform 1059 32-bit DMA. When set to 1, the chip will be able to perform DMA 1060 to addresses up to 1TB. When set to 2, the driver supports the 1061 full 64-bit DMA address range, but can only address 16 segments 1062 of 4 GB each. This limits the total addressable range to 64 GB. 1063 1064 Most machines with less than 4GB of memory should use a setting 1065 of 0 for best performance. If your machine has 4GB of memory 1066 or more, you should set this option to 1 (the default). 1067 1068 The still experimental value 2 (64 bit DMA addressing with 16 1069 x 4GB segments limitation) can be used on systems that require 1070 PCI address bits past bit 39 to be set for the addressing of 1071 memory using PCI DAC cycles. 1072 1073config SCSI_SYM53C8XX_DEFAULT_TAGS 1074 int "Default tagged command queue depth" 1075 depends on SCSI_SYM53C8XX_2 1076 default "16" 1077 help 1078 This is the default value of the command queue depth the 1079 driver will announce to the generic SCSI layer for devices 1080 that support tagged command queueing. This value can be changed 1081 from the boot command line. This is a soft limit that cannot 1082 exceed CONFIG_SCSI_SYM53C8XX_MAX_TAGS. 1083 1084config SCSI_SYM53C8XX_MAX_TAGS 1085 int "Maximum number of queued commands" 1086 depends on SCSI_SYM53C8XX_2 1087 default "64" 1088 help 1089 This option allows you to specify the maximum number of commands 1090 that can be queued to any device, when tagged command queuing is 1091 possible. The driver supports up to 256 queued commands per device. 1092 This value is used as a compiled-in hard limit. 1093 1094config SCSI_SYM53C8XX_MMIO 1095 bool "Use memory mapped IO" 1096 depends on SCSI_SYM53C8XX_2 1097 default y 1098 help 1099 Memory mapped IO is faster than Port IO. Most people should 1100 answer Y here, but some machines may have problems. If you have 1101 to answer N here, please report the problem to the maintainer. 1102 1103config SCSI_IPR 1104 tristate "IBM Power Linux RAID adapter support" 1105 depends on PCI && SCSI && ATA 1106 select FW_LOADER 1107 ---help--- 1108 This driver supports the IBM Power Linux family RAID adapters. 1109 This includes IBM pSeries 5712, 5703, 5709, and 570A, as well 1110 as IBM iSeries 5702, 5703, 5709, and 570A. 1111 1112config SCSI_IPR_TRACE 1113 bool "enable driver internal trace" 1114 depends on SCSI_IPR 1115 default y 1116 help 1117 If you say Y here, the driver will trace all commands issued 1118 to the adapter. Performance impact is minimal. Trace can be 1119 dumped using /sys/bus/class/scsi_host/hostXX/trace. 1120 1121config SCSI_IPR_DUMP 1122 bool "enable adapter dump support" 1123 depends on SCSI_IPR 1124 default y 1125 help 1126 If you say Y here, the driver will support adapter crash dump. 1127 If you enable this support, the iprdump daemon can be used 1128 to capture adapter failure analysis information. 1129 1130config SCSI_ZALON 1131 tristate "Zalon SCSI support" 1132 depends on GSC && SCSI 1133 select SCSI_SPI_ATTRS 1134 help 1135 The Zalon is a GSC/HSC bus interface chip that sits between the 1136 PA-RISC processor and the NCR 53c720 SCSI controller on C100, 1137 C110, J200, J210 and some D, K & R-class machines. It's also 1138 used on the add-in Bluefish, Barracuda & Shrike SCSI cards. 1139 Say Y here if you have one of these machines or cards. 1140 1141config SCSI_NCR_Q720 1142 tristate "NCR Quad 720 MCA SCSI support" 1143 depends on MCA && SCSI 1144 select SCSI_SPI_ATTRS 1145 help 1146 This is a driver for the MicroChannel Quad 720 card produced by 1147 NCR and commonly used in 345x/35xx/4100 class machines. It always 1148 tries to negotiate sync and uses tag command queueing. 1149 1150 Unless you have an NCR manufactured machine, the chances are that 1151 you do not have this SCSI card, so say N. 1152 1153config SCSI_NCR53C8XX_DEFAULT_TAGS 1154 int "default tagged command queue depth" 1155 depends on SCSI_ZALON || SCSI_NCR_Q720 1156 default "8" 1157 ---help--- 1158 "Tagged command queuing" is a feature of SCSI-2 which improves 1159 performance: the host adapter can send several SCSI commands to a 1160 device's queue even if previous commands haven't finished yet. 1161 Because the device is intelligent, it can optimize its operations 1162 (like head positioning) based on its own request queue. Some SCSI 1163 devices don't implement this properly; if you want to disable this 1164 feature, enter 0 or 1 here (it doesn't matter which). 1165 1166 The default value is 8 and should be supported by most hard disks. 1167 This value can be overridden from the boot command line using the 1168 'tags' option as follows (example): 1169 'ncr53c8xx=tags:4/t2t3q16/t0u2q10' will set default queue depth to 1170 4, set queue depth to 16 for target 2 and target 3 on controller 0 1171 and set queue depth to 10 for target 0 / lun 2 on controller 1. 1172 1173 The normal answer therefore is to go with the default 8 and to use 1174 a boot command line option for devices that need to use a different 1175 command queue depth. 1176 1177 There is no safe option other than using good SCSI devices. 1178 1179config SCSI_NCR53C8XX_MAX_TAGS 1180 int "maximum number of queued commands" 1181 depends on SCSI_ZALON || SCSI_NCR_Q720 1182 default "32" 1183 ---help--- 1184 This option allows you to specify the maximum number of commands 1185 that can be queued to any device, when tagged command queuing is 1186 possible. The default value is 32. Minimum is 2, maximum is 64. 1187 Modern hard disks are able to support 64 tags and even more, but 1188 do not seem to be faster when more than 32 tags are being used. 1189 1190 So, the normal answer here is to go with the default value 32 unless 1191 you are using very large hard disks with large cache (>= 1 MB) that 1192 are able to take advantage of more than 32 tagged commands. 1193 1194 There is no safe option and the default answer is recommended. 1195 1196config SCSI_NCR53C8XX_SYNC 1197 int "synchronous transfers frequency in MHz" 1198 depends on SCSI_ZALON || SCSI_NCR_Q720 1199 default "20" 1200 ---help--- 1201 The SCSI Parallel Interface-2 Standard defines 5 classes of transfer 1202 rates: FAST-5, FAST-10, FAST-20, FAST-40 and FAST-80. The numbers 1203 are respectively the maximum data transfer rates in mega-transfers 1204 per second for each class. For example, a FAST-20 Wide 16 device is 1205 able to transfer data at 20 million 16 bit packets per second for a 1206 total rate of 40 MB/s. 1207 1208 You may specify 0 if you want to only use asynchronous data 1209 transfers. This is the safest and slowest option. Otherwise, specify 1210 a value between 5 and 80, depending on the capability of your SCSI 1211 controller. The higher the number, the faster the data transfer. 1212 Note that 80 should normally be ok since the driver decreases the 1213 value automatically according to the controller's capabilities. 1214 1215 Your answer to this question is ignored for controllers with NVRAM, 1216 since the driver will get this information from the user set-up. It 1217 also can be overridden using a boot setup option, as follows 1218 (example): 'ncr53c8xx=sync:12' will allow the driver to negotiate 1219 for FAST-20 synchronous data transfer (20 mega-transfers per 1220 second). 1221 1222 The normal answer therefore is not to go with the default but to 1223 select the maximum value 80 allowing the driver to use the maximum 1224 value supported by each controller. If this causes problems with 1225 your SCSI devices, you should come back and decrease the value. 1226 1227 There is no safe option other than using good cabling, right 1228 terminations and SCSI conformant devices. 1229 1230config SCSI_NCR53C8XX_NO_DISCONNECT 1231 bool "not allow targets to disconnect" 1232 depends on (SCSI_ZALON || SCSI_NCR_Q720) && SCSI_NCR53C8XX_DEFAULT_TAGS=0 1233 help 1234 This option is only provided for safety if you suspect some SCSI 1235 device of yours to not support properly the target-disconnect 1236 feature. In that case, you would say Y here. In general however, to 1237 not allow targets to disconnect is not reasonable if there is more 1238 than 1 device on a SCSI bus. The normal answer therefore is N. 1239 1240config SCSI_PAS16 1241 tristate "PAS16 SCSI support" 1242 depends on ISA && SCSI 1243 select SCSI_SPI_ATTRS 1244 ---help--- 1245 This is support for a SCSI host adapter. It is explained in section 1246 3.10 of the SCSI-HOWTO, available from 1247 <http://www.tldp.org/docs.html#howto>. If it doesn't work out 1248 of the box, you may have to change some settings in 1249 <file:drivers/scsi/pas16.h>. 1250 1251 To compile this driver as a module, choose M here: the 1252 module will be called pas16. 1253 1254config SCSI_QLOGIC_FAS 1255 tristate "Qlogic FAS SCSI support" 1256 depends on ISA && SCSI 1257 ---help--- 1258 This is a driver for the ISA, VLB, and PCMCIA versions of the Qlogic 1259 FastSCSI! cards as well as any other card based on the FASXX chip 1260 (including the Control Concepts SCSI/IDE/SIO/PIO/FDC cards). 1261 1262 This driver does NOT support the PCI versions of these cards. The 1263 PCI versions are supported by the Qlogic ISP driver ("Qlogic ISP 1264 SCSI support"), below. 1265 1266 Information about this driver is contained in 1267 <file:Documentation/scsi/qlogicfas.txt>. You should also read the 1268 SCSI-HOWTO, available from 1269 <http://www.tldp.org/docs.html#howto>. 1270 1271 To compile this driver as a module, choose M here: the 1272 module will be called qlogicfas. 1273 1274config SCSI_QLOGIC_1280 1275 tristate "Qlogic QLA 1240/1x80/1x160 SCSI support" 1276 depends on PCI && SCSI 1277 help 1278 Say Y if you have a QLogic ISP1240/1x80/1x160 SCSI host adapter. 1279 1280 To compile this driver as a module, choose M here: the 1281 module will be called qla1280. 1282 1283config SCSI_QLOGICPTI 1284 tristate "PTI Qlogic, ISP Driver" 1285 depends on SBUS && SCSI 1286 help 1287 This driver supports SBUS SCSI controllers from PTI or QLogic. These 1288 controllers are known under Solaris as qpti and in the openprom as 1289 PTI,ptisp or QLGC,isp. Note that PCI QLogic SCSI controllers are 1290 driven by a different driver. 1291 1292 To compile this driver as a module, choose M here: the 1293 module will be called qlogicpti. 1294 1295source "drivers/scsi/qla2xxx/Kconfig" 1296source "drivers/scsi/qla4xxx/Kconfig" 1297 1298config SCSI_LPFC 1299 tristate "Emulex LightPulse Fibre Channel Support" 1300 depends on PCI && SCSI 1301 depends on SCSI_FC_ATTRS 1302 select CRC_T10DIF 1303 help 1304 This lpfc driver supports the Emulex LightPulse 1305 Family of Fibre Channel PCI host adapters. 1306 1307config SCSI_LPFC_DEBUG_FS 1308 bool "Emulex LightPulse Fibre Channel debugfs Support" 1309 depends on SCSI_LPFC && DEBUG_FS 1310 help 1311 This makes debugging information from the lpfc driver 1312 available via the debugfs filesystem. 1313 1314config SCSI_SIM710 1315 tristate "Simple 53c710 SCSI support (Compaq, NCR machines)" 1316 depends on (EISA || MCA) && SCSI 1317 select SCSI_SPI_ATTRS 1318 ---help--- 1319 This driver is for NCR53c710 based SCSI host adapters. 1320 1321 It currently supports Compaq EISA cards and NCR MCA cards 1322 1323config SCSI_SYM53C416 1324 tristate "Symbios 53c416 SCSI support" 1325 depends on ISA && SCSI 1326 ---help--- 1327 This is support for the sym53c416 SCSI host adapter, the SCSI 1328 adapter that comes with some HP scanners. This driver requires that 1329 the sym53c416 is configured first using some sort of PnP 1330 configuration program (e.g. isapnp) or by a PnP aware BIOS. If you 1331 are using isapnp then you need to compile this driver as a module 1332 and then load it using insmod after isapnp has run. The parameters 1333 of the configured card(s) should be passed to the driver. The format 1334 is: 1335 1336 insmod sym53c416 sym53c416=<base>,<irq> [sym53c416_1=<base>,<irq>] 1337 1338 To compile this driver as a module, choose M here: the 1339 module will be called sym53c416. 1340 1341config SCSI_DC395x 1342 tristate "Tekram DC395(U/UW/F) and DC315(U) SCSI support" 1343 depends on PCI && SCSI 1344 ---help--- 1345 This driver supports PCI SCSI host adapters based on the ASIC 1346 TRM-S1040 chip, e.g Tekram DC395(U/UW/F) and DC315(U) variants. 1347 1348 This driver works, but is still in experimental status. So better 1349 have a bootable disk and a backup in case of emergency. 1350 1351 Documentation can be found in <file:Documentation/scsi/dc395x.txt>. 1352 1353 To compile this driver as a module, choose M here: the 1354 module will be called dc395x. 1355 1356config SCSI_AM53C974 1357 tristate "Tekram DC390(T) and Am53/79C974 SCSI support (new driver)" 1358 depends on PCI && SCSI 1359 select SCSI_SPI_ATTRS 1360 ---help--- 1361 This driver supports PCI SCSI host adapters based on the Am53C974A 1362 chip, e.g. Tekram DC390(T), DawiControl 2974 and some onboard 1363 PCscsi/PCnet (Am53/79C974) solutions. 1364 This is a new implementation base on the generic esp_scsi driver. 1365 1366 Documentation can be found in <file:Documentation/scsi/tmscsim.txt>. 1367 1368 Note that this driver does NOT support Tekram DC390W/U/F, which are 1369 based on NCR/Symbios chips. Use "NCR53C8XX SCSI support" for those. 1370 1371 To compile this driver as a module, choose M here: the 1372 module will be called am53c974. 1373 1374config SCSI_T128 1375 tristate "Trantor T128/T128F/T228 SCSI support" 1376 depends on ISA && SCSI 1377 select SCSI_SPI_ATTRS 1378 select CHECK_SIGNATURE 1379 ---help--- 1380 This is support for a SCSI host adapter. It is explained in section 1381 3.11 of the SCSI-HOWTO, available from 1382 <http://www.tldp.org/docs.html#howto>. If it doesn't work out 1383 of the box, you may have to change some settings in 1384 <file:drivers/scsi/t128.h>. Note that Trantor was purchased by 1385 Adaptec, and some former Trantor products are being sold under the 1386 Adaptec name. 1387 1388 To compile this driver as a module, choose M here: the 1389 module will be called t128. 1390 1391config SCSI_U14_34F 1392 tristate "UltraStor 14F/34F support" 1393 depends on ISA && SCSI && ISA_DMA_API 1394 ---help--- 1395 This is support for the UltraStor 14F and 34F SCSI-2 host adapters. 1396 The source at <file:drivers/scsi/u14-34f.c> contains some 1397 information about this hardware. If the driver doesn't work out of 1398 the box, you may have to change some settings in 1399 <file: drivers/scsi/u14-34f.c>. Read the SCSI-HOWTO, available from 1400 <http://www.tldp.org/docs.html#howto>. Note that there is also 1401 another driver for the same hardware: "UltraStor SCSI support", 1402 below. You should say Y to both only if you want 24F support as 1403 well. 1404 1405 To compile this driver as a module, choose M here: the 1406 module will be called u14-34f. 1407 1408config SCSI_U14_34F_TAGGED_QUEUE 1409 bool "enable tagged command queueing" 1410 depends on SCSI_U14_34F 1411 help 1412 This is a feature of SCSI-2 which improves performance: the host 1413 adapter can send several SCSI commands to a device's queue even if 1414 previous commands haven't finished yet. 1415 This is equivalent to the "u14-34f=tc:y" boot option. 1416 1417config SCSI_U14_34F_LINKED_COMMANDS 1418 bool "enable elevator sorting" 1419 depends on SCSI_U14_34F 1420 help 1421 This option enables elevator sorting for all probed SCSI disks and 1422 CD-ROMs. It definitely reduces the average seek distance when doing 1423 random seeks, but this does not necessarily result in a noticeable 1424 performance improvement: your mileage may vary... 1425 This is equivalent to the "u14-34f=lc:y" boot option. 1426 1427config SCSI_U14_34F_MAX_TAGS 1428 int "maximum number of queued commands" 1429 depends on SCSI_U14_34F 1430 default "8" 1431 help 1432 This specifies how many SCSI commands can be maximally queued for 1433 each probed SCSI device. You should reduce the default value of 8 1434 only if you have disks with buggy or limited tagged command support. 1435 Minimum is 2 and maximum is 14. This value is also the window size 1436 used by the elevator sorting option above. The effective value used 1437 by the driver for each probed SCSI device is reported at boot time. 1438 This is equivalent to the "u14-34f=mq:8" boot option. 1439 1440config SCSI_ULTRASTOR 1441 tristate "UltraStor SCSI support" 1442 depends on X86 && ISA && SCSI 1443 ---help--- 1444 This is support for the UltraStor 14F, 24F and 34F SCSI-2 host 1445 adapter family. This driver is explained in section 3.12 of the 1446 SCSI-HOWTO, available from 1447 <http://www.tldp.org/docs.html#howto>. If it doesn't work out 1448 of the box, you may have to change some settings in 1449 <file:drivers/scsi/ultrastor.h>. 1450 1451 Note that there is also another driver for the same hardware: 1452 "UltraStor 14F/34F support", above. 1453 1454 To compile this driver as a module, choose M here: the 1455 module will be called ultrastor. 1456 1457config SCSI_NSP32 1458 tristate "Workbit NinjaSCSI-32Bi/UDE support" 1459 depends on PCI && SCSI && !64BIT 1460 help 1461 This is support for the Workbit NinjaSCSI-32Bi/UDE PCI/Cardbus 1462 SCSI host adapter. Please read the SCSI-HOWTO, available from 1463 <http://www.tldp.org/docs.html#howto>. 1464 1465 To compile this driver as a module, choose M here: the 1466 module will be called nsp32. 1467 1468config SCSI_WD719X 1469 tristate "Western Digital WD7193/7197/7296 support" 1470 depends on PCI && SCSI 1471 select EEPROM_93CX6 1472 ---help--- 1473 This is a driver for Western Digital WD7193, WD7197 and WD7296 PCI 1474 SCSI controllers (based on WD33C296A chip). 1475 1476config SCSI_DEBUG 1477 tristate "SCSI debugging host and device simulator" 1478 depends on SCSI 1479 select CRC_T10DIF 1480 help 1481 This pseudo driver simulates one or more hosts (SCSI initiators), 1482 each with one or more targets, each with one or more logical units. 1483 Defaults to one of each, creating a small RAM disk device. Many 1484 parameters found in the /sys/bus/pseudo/drivers/scsi_debug 1485 directory can be tweaked at run time. 1486 See <http://sg.danny.cz/sg/sdebug26.html> for more information. 1487 Mainly used for testing and best as a module. If unsure, say N. 1488 1489config SCSI_MESH 1490 tristate "MESH (Power Mac internal SCSI) support" 1491 depends on PPC32 && PPC_PMAC && SCSI 1492 help 1493 Many Power Macintoshes and clones have a MESH (Macintosh Enhanced 1494 SCSI Hardware) SCSI bus adaptor (the 7200 doesn't, but all of the 1495 other Power Macintoshes do). Say Y to include support for this SCSI 1496 adaptor. 1497 1498 To compile this driver as a module, choose M here: the 1499 module will be called mesh. 1500 1501config SCSI_MESH_SYNC_RATE 1502 int "maximum synchronous transfer rate (MB/s) (0 = async)" 1503 depends on SCSI_MESH 1504 default "5" 1505 help 1506 On Power Macintoshes (and clones) where the MESH SCSI bus adaptor 1507 drives a bus which is entirely internal to the machine (such as the 1508 7500, 7600, 8500, etc.), the MESH is capable of synchronous 1509 operation at up to 10 MB/s. On machines where the SCSI bus 1510 controlled by the MESH can have external devices connected, it is 1511 usually rated at 5 MB/s. 5 is a safe value here unless you know the 1512 MESH SCSI bus is internal only; in that case you can say 10. Say 0 1513 to disable synchronous operation. 1514 1515config SCSI_MESH_RESET_DELAY_MS 1516 int "initial bus reset delay (ms) (0 = no reset)" 1517 depends on SCSI_MESH 1518 default "4000" 1519 1520config SCSI_MAC53C94 1521 tristate "53C94 (Power Mac external SCSI) support" 1522 depends on PPC32 && PPC_PMAC && SCSI 1523 help 1524 On Power Macintoshes (and clones) with two SCSI buses, the external 1525 SCSI bus is usually controlled by a 53C94 SCSI bus adaptor. Older 1526 machines which only have one SCSI bus, such as the 7200, also use 1527 the 53C94. Say Y to include support for the 53C94. 1528 1529 To compile this driver as a module, choose M here: the 1530 module will be called mac53c94. 1531 1532source "drivers/scsi/arm/Kconfig" 1533 1534config JAZZ_ESP 1535 bool "MIPS JAZZ FAS216 SCSI support" 1536 depends on MACH_JAZZ && SCSI 1537 select SCSI_SPI_ATTRS 1538 help 1539 This is the driver for the onboard SCSI host adapter of MIPS Magnum 1540 4000, Acer PICA, Olivetti M700-10 and a few other identical OEM 1541 systems. 1542 1543config A3000_SCSI 1544 tristate "A3000 WD33C93A support" 1545 depends on AMIGA && SCSI 1546 help 1547 If you have an Amiga 3000 and have SCSI devices connected to the 1548 built-in SCSI controller, say Y. Otherwise, say N. 1549 1550 To compile this driver as a module, choose M here: the 1551 module will be called a3000. 1552 1553config A2091_SCSI 1554 tristate "A2091/A590 WD33C93A support" 1555 depends on ZORRO && SCSI 1556 help 1557 If you have a Commodore A2091 SCSI controller, say Y. Otherwise, 1558 say N. 1559 1560 To compile this driver as a module, choose M here: the 1561 module will be called a2091. 1562 1563config GVP11_SCSI 1564 tristate "GVP Series II WD33C93A support" 1565 depends on ZORRO && SCSI 1566 ---help--- 1567 If you have a Great Valley Products Series II SCSI controller, 1568 answer Y. Also say Y if you have a later model of GVP SCSI 1569 controller (such as the GVP A4008 or a Combo board). Otherwise, 1570 answer N. This driver does NOT work for the T-Rex series of 1571 accelerators from TekMagic and GVP-M. 1572 1573 To compile this driver as a module, choose M here: the 1574 module will be called gvp11. 1575 1576config SCSI_A4000T 1577 tristate "A4000T NCR53c710 SCSI support" 1578 depends on AMIGA && SCSI 1579 select SCSI_SPI_ATTRS 1580 help 1581 If you have an Amiga 4000T and have SCSI devices connected to the 1582 built-in SCSI controller, say Y. Otherwise, say N. 1583 1584 To compile this driver as a module, choose M here: the 1585 module will be called a4000t. 1586 1587config SCSI_ZORRO7XX 1588 tristate "Zorro NCR53c710 SCSI support" 1589 depends on ZORRO && SCSI 1590 select SCSI_SPI_ATTRS 1591 help 1592 Support for various NCR53c710-based SCSI controllers on Zorro 1593 expansion boards for the Amiga. 1594 This includes: 1595 - the Amiga 4091 Zorro III SCSI-2 controller, 1596 - the MacroSystem Development's WarpEngine Amiga SCSI-2 controller 1597 (info at 1598 <http://www.lysator.liu.se/amiga/ar/guide/ar310.guide?FEATURE5>), 1599 - the SCSI controller on the Phase5 Blizzard PowerUP 603e+ 1600 accelerator card for the Amiga 1200, 1601 - the SCSI controller on the GVP Turbo 040/060 accelerator. 1602 1603config ATARI_SCSI 1604 tristate "Atari native SCSI support" 1605 depends on ATARI && SCSI 1606 select SCSI_SPI_ATTRS 1607 select NVRAM 1608 ---help--- 1609 If you have an Atari with built-in NCR5380 SCSI controller (TT, 1610 Falcon, ...) say Y to get it supported. Of course also, if you have 1611 a compatible SCSI controller (e.g. for Medusa). 1612 1613 To compile this driver as a module, choose M here: the 1614 module will be called atari_scsi. 1615 1616 This driver supports both styles of NCR integration into the 1617 system: the TT style (separate DMA), and the Falcon style (via 1618 ST-DMA, replacing ACSI). It does NOT support other schemes, like 1619 in the Hades (without DMA). 1620 1621config ATARI_SCSI_TOSHIBA_DELAY 1622 bool "Long delays for Toshiba CD-ROMs" 1623 depends on ATARI_SCSI 1624 help 1625 This option increases the delay after a SCSI arbitration to 1626 accommodate some flaky Toshiba CD-ROM drives. Say Y if you intend to 1627 use a Toshiba CD-ROM drive; otherwise, the option is not needed and 1628 would impact performance a bit, so say N. 1629 1630config ATARI_SCSI_RESET_BOOT 1631 bool "Reset SCSI-devices at boottime" 1632 depends on ATARI_SCSI 1633 help 1634 Reset the devices on your Atari whenever it boots. This makes the 1635 boot process fractionally longer but may assist recovery from errors 1636 that leave the devices with SCSI operations partway completed. 1637 1638config MAC_SCSI 1639 tristate "Macintosh NCR5380 SCSI" 1640 depends on MAC && SCSI 1641 select SCSI_SPI_ATTRS 1642 help 1643 This is the NCR 5380 SCSI controller included on most of the 68030 1644 based Macintoshes. If you have one of these say Y and read the 1645 SCSI-HOWTO, available from 1646 <http://www.tldp.org/docs.html#howto>. 1647 1648config SCSI_MAC_ESP 1649 tristate "Macintosh NCR53c9[46] SCSI" 1650 depends on MAC && SCSI 1651 select SCSI_SPI_ATTRS 1652 help 1653 This is the NCR 53c9x SCSI controller found on most of the 68040 1654 based Macintoshes. 1655 1656 To compile this driver as a module, choose M here: the module 1657 will be called mac_esp. 1658 1659config MVME147_SCSI 1660 bool "WD33C93 SCSI driver for MVME147" 1661 depends on MVME147 && SCSI=y 1662 select SCSI_SPI_ATTRS 1663 help 1664 Support for the on-board SCSI controller on the Motorola MVME147 1665 single-board computer. 1666 1667config MVME16x_SCSI 1668 tristate "NCR53C710 SCSI driver for MVME16x" 1669 depends on MVME16x && SCSI 1670 select SCSI_SPI_ATTRS 1671 help 1672 The Motorola MVME162, 166, 167, 172 and 177 boards use the NCR53C710 1673 SCSI controller chip. Almost everyone using one of these boards 1674 will want to say Y to this question. 1675 1676config BVME6000_SCSI 1677 tristate "NCR53C710 SCSI driver for BVME6000" 1678 depends on BVME6000 && SCSI 1679 select SCSI_SPI_ATTRS 1680 help 1681 The BVME4000 and BVME6000 boards from BVM Ltd use the NCR53C710 1682 SCSI controller chip. Almost everyone using one of these boards 1683 will want to say Y to this question. 1684 1685config SUN3_SCSI 1686 tristate "Sun3 NCR5380 SCSI" 1687 depends on SUN3 && SCSI 1688 select SCSI_SPI_ATTRS 1689 help 1690 This option will enable support for the OBIO (onboard io) NCR5380 1691 SCSI controller found in the Sun 3/50 and 3/60, as well as for 1692 "Sun3" type VME scsi controllers also based on the NCR5380. 1693 General Linux information on the Sun 3 series (now discontinued) 1694 is at <http://www.angelfire.com/ca2/tech68k/sun3.html>. 1695 1696config SUN3X_ESP 1697 bool "Sun3x ESP SCSI" 1698 depends on SUN3X && SCSI=y 1699 select SCSI_SPI_ATTRS 1700 help 1701 The ESP was an on-board SCSI controller used on Sun 3/80 1702 machines. Say Y here to compile in support for it. 1703 1704config SCSI_SUNESP 1705 tristate "Sparc ESP Scsi Driver" 1706 depends on SBUS && SCSI 1707 select SCSI_SPI_ATTRS 1708 help 1709 This is the driver for the Sun ESP SCSI host adapter. The ESP 1710 chipset is present in most SPARC SBUS-based computers and 1711 supports the Emulex family of ESP SCSI chips (esp100, esp100A, 1712 esp236, fas101, fas236) as well as the Qlogic fas366 SCSI chip. 1713 1714 To compile this driver as a module, choose M here: the 1715 module will be called sun_esp. 1716 1717config ZFCP 1718 tristate "FCP host bus adapter driver for IBM eServer zSeries" 1719 depends on S390 && QDIO && SCSI 1720 depends on SCSI_FC_ATTRS 1721 help 1722 If you want to access SCSI devices attached to your IBM eServer 1723 zSeries by means of Fibre Channel interfaces say Y. 1724 For details please refer to the documentation provided by IBM at 1725 <http://oss.software.ibm.com/developerworks/opensource/linux390> 1726 1727 This driver is also available as a module. This module will be 1728 called zfcp. If you want to compile it as a module, say M here 1729 and read <file:Documentation/kbuild/modules.txt>. 1730 1731config SCSI_PMCRAID 1732 tristate "PMC SIERRA Linux MaxRAID adapter support" 1733 depends on PCI && SCSI && NET 1734 ---help--- 1735 This driver supports the PMC SIERRA MaxRAID adapters. 1736 1737config SCSI_PM8001 1738 tristate "PMC-Sierra SPC 8001 SAS/SATA Based Host Adapter driver" 1739 depends on PCI && SCSI 1740 select SCSI_SAS_LIBSAS 1741 help 1742 This driver supports PMC-Sierra PCIE SAS/SATA 8x6G SPC 8001 chip 1743 based host adapters. 1744 1745config SCSI_BFA_FC 1746 tristate "Brocade BFA Fibre Channel Support" 1747 depends on PCI && SCSI 1748 depends on SCSI_FC_ATTRS 1749 help 1750 This bfa driver supports all Brocade PCIe FC/FCOE host adapters. 1751 1752 To compile this driver as a module, choose M here. The module will 1753 be called bfa. 1754 1755config SCSI_VIRTIO 1756 tristate "virtio-scsi support" 1757 depends on VIRTIO 1758 help 1759 This is the virtual HBA driver for virtio. If the kernel will 1760 be used in a virtual machine, say Y or M. 1761 1762source "drivers/scsi/csiostor/Kconfig" 1763 1764endif # SCSI_LOWLEVEL 1765 1766source "drivers/scsi/pcmcia/Kconfig" 1767 1768source "drivers/scsi/device_handler/Kconfig" 1769 1770source "drivers/scsi/osd/Kconfig" 1771 1772endmenu 1773