1 /* ///////////////////////////////////////////////////////////////////////// */ 2 /* */ 3 /* Copyright (c) Atmel Corporation. All rights reserved. */ 4 /* */ 5 /* Module Name: wilc_wlan_if.h */ 6 /* */ 7 /* */ 8 /* ///////////////////////////////////////////////////////////////////////// */ 9 10 #ifndef WILC_WLAN_IF_H 11 #define WILC_WLAN_IF_H 12 13 #include <linux/netdevice.h> 14 15 /******************************************** 16 * 17 * Host Interface Defines 18 * 19 ********************************************/ 20 21 #define HIF_SDIO (0) 22 #define HIF_SPI BIT(0) 23 #define HIF_SDIO_GPIO_IRQ BIT(2) 24 25 /******************************************** 26 * 27 * Wlan Interface Defines 28 * 29 ********************************************/ 30 31 struct sdio_cmd52 { 32 u32 read_write: 1; 33 u32 function: 3; 34 u32 raw: 1; 35 u32 address: 17; 36 u32 data: 8; 37 }; 38 39 struct sdio_cmd53 { 40 u32 read_write: 1; 41 u32 function: 3; 42 u32 block_mode: 1; 43 u32 increment: 1; 44 u32 address: 17; 45 u32 count: 9; 46 u8 *buffer; 47 u32 block_size; 48 }; 49 50 #define WILC_MAC_INDICATE_STATUS 0x1 51 #define WILC_MAC_STATUS_INIT -1 52 #define WILC_MAC_STATUS_READY 0 53 #define WILC_MAC_STATUS_CONNECT 1 54 55 #define WILC_MAC_INDICATE_SCAN 0x2 56 57 struct tx_complete_data { 58 int size; 59 void *buff; 60 u8 *bssid; 61 struct sk_buff *skb; 62 }; 63 64 typedef void (*wilc_tx_complete_func_t)(void *, int); 65 66 #define WILC_TX_ERR_NO_BUF (-2) 67 68 /******************************************** 69 * 70 * Wlan Configuration ID 71 * 72 ********************************************/ 73 #define WILC_MULTICAST_TABLE_SIZE 8 74 #define MAX_SSID_LEN 33 75 #define MAX_RATES_SUPPORTED 12 76 77 typedef enum { 78 SUPP_RATES_IE = 1, 79 EXT_SUPP_RATES_IE = 50, 80 HT_CAPABILITY_IE = 45, 81 RSN_IE = 48, 82 WPA_IE = 221, 83 WMM_IE = 221, 84 P2P_IE = 221, 85 } BEACON_IE; 86 87 typedef enum { 88 INFRASTRUCTURE = 0, 89 INDEPENDENT, 90 AP, 91 } BSSTYPE_T; 92 93 typedef enum { 94 RATE_AUTO = 0, 95 RATE_1MB = 1, 96 RATE_2MB = 2, 97 RATE_5MB = 5, 98 RATE_6MB = 6, 99 RATE_9MB = 9, 100 RATE_11MB = 11, 101 RATE_12MB = 12, 102 RATE_18MB = 18, 103 RATE_24MB = 24, 104 RATE_26MB = 36, 105 RATE_48MB = 48, 106 RATE_54MB = 54 107 } TX_RATE_T; 108 109 typedef enum { 110 B_ONLY_MODE = 0, /* 1, 2 M, otherwise 5, 11 M */ 111 G_ONLY_MODE, /* 6,12,24 otherwise 9,18,36,48,54 */ 112 G_MIXED_11B_1_MODE, /* 1,2,5.5,11 otherwise all on */ 113 G_MIXED_11B_2_MODE, /* 1,2,5,11,6,12,24 otherwise all on */ 114 } G_OPERATING_MODE_T; 115 116 typedef enum { 117 G_SHORT_PREAMBLE = 0, /* Short Preamble */ 118 G_LONG_PREAMBLE = 1, /* Long Preamble */ 119 G_AUTO_PREAMBLE = 2, /* Auto Preamble Selection */ 120 } G_PREAMBLE_T; 121 122 #define MAC_CONNECTED 1 123 #define MAC_DISCONNECTED 0 124 125 #define SCAN_DONE TRUE 126 typedef enum { 127 PASSIVE_SCAN = 0, 128 ACTIVE_SCAN = 1, 129 } SCANTYPE_T; 130 131 typedef enum { 132 NO_POWERSAVE = 0, 133 MIN_FAST_PS = 1, 134 MAX_FAST_PS = 2, 135 MIN_PSPOLL_PS = 3, 136 MAX_PSPOLL_PS = 4 137 } USER_PS_MODE_T; 138 139 typedef enum { 140 CHIP_WAKEDUP = 0, 141 CHIP_SLEEPING_AUTO = 1, 142 CHIP_SLEEPING_MANUAL = 2 143 } CHIP_PS_STATE_T; 144 145 typedef enum { 146 ACQUIRE_ONLY = 0, 147 ACQUIRE_AND_WAKEUP = 1, 148 } BUS_ACQUIRE_T; 149 150 typedef enum { 151 RELEASE_ONLY = 0, 152 RELEASE_ALLOW_SLEEP = 1, 153 } BUS_RELEASE_T; 154 155 typedef enum { 156 NO_SECURITY = 0, 157 WEP_40 = 0x3, 158 WEP_104 = 0x7, 159 WPA_AES = 0x29, 160 WPA_TKIP = 0x49, 161 WPA_AES_TKIP = 0x69, /* Aes or Tkip */ 162 WPA2_AES = 0x31, 163 WPA2_TKIP = 0x51, 164 WPA2_AES_TKIP = 0x71, /* Aes or Tkip */ 165 } SECURITY_T; 166 167 enum AUTHTYPE { 168 OPEN_SYSTEM = 1, 169 SHARED_KEY = 2, 170 ANY = 3, 171 IEEE8021 = 5 172 }; 173 174 enum SITESURVEY { 175 SITE_SURVEY_1CH = 0, 176 SITE_SURVEY_ALL_CH = 1, 177 SITE_SURVEY_OFF = 2 178 }; 179 180 typedef enum { 181 NORMAL_ACK = 0, 182 NO_ACK, 183 } ACK_POLICY_T; 184 185 typedef enum { 186 DONT_RESET = 0, 187 DO_RESET = 1, 188 NO_REQUEST = 2, 189 } RESET_REQ_T; 190 191 typedef enum { 192 REKEY_DISABLE = 1, 193 REKEY_TIME_BASE, 194 REKEY_PKT_BASE, 195 REKEY_TIME_PKT_BASE 196 } RSNA_REKEY_POLICY_T; 197 198 typedef enum { 199 FILTER_NO = 0x00, 200 FILTER_AP_ONLY = 0x01, 201 FILTER_STA_ONLY = 0x02 202 } SCAN_CLASS_FITLER_T; 203 204 typedef enum { 205 PRI_HIGH_RSSI = 0x00, 206 PRI_LOW_RSSI = 0x04, 207 PRI_DETECT = 0x08 208 } SCAN_PRI_T; 209 210 typedef enum { 211 CH_FILTER_OFF = 0x00, 212 CH_FILTER_ON = 0x10 213 } CH_FILTER_T; 214 215 typedef enum { 216 AUTO_PROT = 0, /* Auto */ 217 NO_PROT, /* Do not use any protection */ 218 ERP_PROT, /* Protect all ERP frame exchanges */ 219 HT_PROT, /* Protect all HT frame exchanges */ 220 GF_PROT, /* Protect all GF frame exchanges */ 221 } N_PROTECTION_MODE_T; 222 223 typedef enum { 224 G_SELF_CTS_PROT, 225 G_RTS_CTS_PROT, 226 } G_PROTECTION_MODE_T; 227 228 typedef enum { 229 HT_MIXED_MODE = 1, 230 HT_ONLY_20MHZ_MODE, 231 HT_ONLY_20_40MHZ_MODE, 232 } N_OPERATING_MODE_T; 233 234 typedef enum { 235 NO_DETECT = 0, 236 DETECT_ONLY = 1, 237 DETECT_PROTECT = 2, 238 DETECT_PROTECT_REPORT = 3, 239 } N_OBSS_DETECTION_T; 240 241 typedef enum { 242 RTS_CTS_NONHT_PROT = 0, /* RTS-CTS at non-HT rate */ 243 FIRST_FRAME_NONHT_PROT, /* First frame at non-HT rate */ 244 LSIG_TXOP_PROT, /* LSIG TXOP Protection */ 245 FIRST_FRAME_MIXED_PROT, /* First frame at Mixed format */ 246 } N_PROTECTION_TYPE_T; 247 248 typedef enum { 249 STATIC_MODE = 1, 250 DYNAMIC_MODE = 2, 251 MIMO_MODE = 3, /* power save disable */ 252 } N_SMPS_MODE_T; 253 254 typedef enum { 255 DISABLE_SELF_CTS, 256 ENABLE_SELF_CTS, 257 DISABLE_TX_ABORT, 258 ENABLE_TX_ABORT, 259 HW_TRIGGER_ABORT, 260 SW_TRIGGER_ABORT, 261 } TX_ABORT_OPTION_T; 262 263 enum wid_type { 264 WID_CHAR = 0, 265 WID_SHORT = 1, 266 WID_INT = 2, 267 WID_STR = 3, 268 WID_BIN_DATA = 4, 269 WID_BIN = 5, 270 WID_IP = 6, 271 WID_ADR = 7, 272 WID_UNDEF = 8, 273 WID_TYPE_FORCE_32BIT = 0xFFFFFFFF 274 }; 275 276 struct wid { 277 u16 id; 278 enum wid_type type; 279 s32 size; 280 s8 *val; 281 }; 282 283 typedef enum { 284 WID_NIL = 0xffff, 285 286 /* 287 * BSS Type 288 * ----------------------------------------------------------- 289 * Configuration : Infrastructure Independent Access Point 290 * Values to set : 0 1 2 291 * ----------------------------------------------------------- 292 */ 293 WID_BSS_TYPE = 0x0000, 294 295 /* 296 * Transmit Rate 297 * ----------------------------------------------------------- 298 * Configuration : 1 2 5.5 11 6 9 12 18 24 36 48 54 299 * Values to set : 1 2 5 11 6 9 12 18 24 36 48 54 300 * ----------------------------------------------------------- 301 */ 302 WID_CURRENT_TX_RATE = 0x0001, 303 304 /* 305 * Channel 306 * ----------------------------------------------------------- 307 * Configuration(g) : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 308 * Values to set : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 309 * ----------------------------------------------------------- 310 */ 311 WID_CURRENT_CHANNEL = 0x0002, 312 313 /* 314 * Preamble 315 * ----------------------------------------------------------- 316 * Configuration : short long Auto 317 * Values to set : 0 1 2 318 * ----------------------------------------------------------- 319 */ 320 WID_PREAMBLE = 0x0003, 321 322 /* 323 * 11g operating mode (ignored if 11g not present) 324 * ----------------------------------------------------------- 325 * Configuration : HighPerf Compat(RSet #1) Compat(RSet #2) 326 * Values to set : 1 2 3 327 * ----------------------------------------------------------- 328 */ 329 WID_11G_OPERATING_MODE = 0x0004, 330 331 /* 332 * Mac status (response only) 333 * ----------------------------------------------------------- 334 * Configuration : disconnect connect 335 * Values to get : 0 1 336 * ----------------------------------------------------------- 337 */ 338 WID_STATUS = 0x0005, 339 340 /* 341 * Scan type 342 * ----------------------------------------------------------- 343 * Configuration : Passive Scanning Active Scanning 344 * Values to set : 0 1 345 * ----------------------------------------------------------- 346 */ 347 WID_SCAN_TYPE = 0x0007, 348 349 /* 350 * Key Id (WEP default key Id) 351 * ----------------------------------------------------------- 352 * Configuration : Any value between 0 to 3 353 * Values to set : Same value. Default is 0 354 * ----------------------------------------------------------- 355 */ 356 WID_KEY_ID = 0x0009, 357 358 /* 359 * QoS Enable 360 * ----------------------------------------------------------- 361 * Configuration : QoS Disable WMM Enable 362 * Values to set : 0 1 363 * ----------------------------------------------------------- 364 */ 365 WID_QOS_ENABLE = 0x000A, 366 367 /* 368 * Power Management 369 * ----------------------------------------------------------- 370 * Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE 371 * Values to set : 0 1 2 372 * ----------------------------------------------------------- 373 */ 374 WID_POWER_MANAGEMENT = 0x000B, 375 376 /* 377 * WEP/802 11I Configuration 378 * ----------------------------------------------------------- 379 * Configuration:Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP 380 * Values (0x) : 00 03 07 29 49 31 51 381 * Configuration:WPA-AES+TKIP RSN-AES+TKIP 382 * Values (0x) : 69 71 383 * ----------------------------------------------------------- 384 */ 385 WID_11I_MODE = 0x000C, 386 387 /* 388 * WEP Configuration: Used in BSS STA mode only when WEP is enabled 389 * ----------------------------------------------------------- 390 * Configuration : Open System Shared Key Any Type | 802.1x Auth 391 * Values (0x) : 01 02 03 | BIT2 392 * ----------------------------------------------------------- 393 */ 394 WID_AUTH_TYPE = 0x000D, 395 396 /* 397 * Site Survey Type 398 * ----------------------------------------------------------- 399 * Configuration : Values to set 400 * Survey 1 Channel : 0 401 * survey all Channels : 1 402 * Disable Site Survey : 2 403 * ----------------------------------------------------------- 404 */ 405 WID_SITE_SURVEY = 0x000E, 406 407 /* 408 * Listen Interval 409 * ----------------------------------------------------------- 410 * Configuration : Any value between 1 to 255 411 * Values to set : Same value. Default is 3 412 * ----------------------------------------------------------- 413 */ 414 WID_LISTEN_INTERVAL = 0x000F, 415 416 /* 417 * DTIM Period 418 * ----------------------------------------------------------- 419 * Configuration : Any value between 1 to 255 420 * Values to set : Same value. Default is 3 421 * ----------------------------------------------------------- 422 */ 423 WID_DTIM_PERIOD = 0x0010, 424 425 /* 426 * ACK Policy 427 * ----------------------------------------------------------- 428 * Configuration : Normal Ack No Ack 429 * Values to set : 0 1 430 * ----------------------------------------------------------- 431 */ 432 WID_ACK_POLICY = 0x0011, 433 434 /* 435 * Reset MAC (Set only) 436 * ----------------------------------------------------------- 437 * Configuration : Don't Reset Reset No Request 438 * Values to set : 0 1 2 439 * ----------------------------------------------------------- 440 */ 441 WID_RESET = 0x0012, 442 443 /* 444 * Broadcast SSID Option: Setting this will adhere to "" SSID element 445 * ----------------------------------------------------------- 446 * Configuration : Enable Disable 447 * Values to set : 1 0 448 * ----------------------------------------------------------- 449 */ 450 WID_BCAST_SSID = 0x0015, 451 452 /* 453 * Disconnect (Station) 454 * ----------------------------------------------------------- 455 * Configuration : Association ID 456 * Values to set : Association ID 457 * ----------------------------------------------------------- 458 */ 459 WID_DISCONNECT = 0x0016, 460 461 /* 462 * 11a Tx Power Level 463 * ----------------------------------------------------------- 464 * Configuration : Sets TX Power (Higher the value greater the power) 465 * Values to set : Any value between 0 and 63 (inclusive Default 48) 466 * ----------------------------------------------------------- 467 */ 468 WID_TX_POWER_LEVEL_11A = 0x0018, 469 470 /* 471 * Group Key Update Policy Selection 472 * ----------------------------------------------------------- 473 * Configuration : Disabled timeBased packetBased timePacketBased 474 * Values to set : 1 2 3 4 475 * ----------------------------------------------------------- 476 */ 477 WID_REKEY_POLICY = 0x0019, 478 479 /* 480 * Allow Short Slot 481 * ----------------------------------------------------------- 482 * Configuration : Disallow Short Slot Allow Short Slot 483 * (Enable Only Long Slot) (Enable Short Slot if applicable) 484 * Values to set : 0 1 485 * ----------------------------------------------------------- 486 */ 487 WID_SHORT_SLOT_ALLOWED = 0x001A, 488 489 WID_PHY_ACTIVE_REG = 0x001B, 490 491 /* 492 * 11b Tx Power Level 493 * ----------------------------------------------------------- 494 * Configuration : Sets TX Power (Higher the value greater the power) 495 * Values to set : Any value between 0 and 63 (inclusive Default 48) 496 * ----------------------------------------------------------- 497 */ 498 WID_TX_POWER_LEVEL_11B = 0x001D, 499 500 /* 501 * Scan Request 502 * ----------------------------------------------------------- 503 * Configuration : Request default scan 504 * Values to set : 0 505 * ----------------------------------------------------------- 506 */ 507 WID_START_SCAN_REQ = 0x001E, 508 509 /* 510 * Rssi (get only) 511 * ----------------------------------------------------------- 512 * Configuration : 513 * Values to get : Rssi value 514 * ----------------------------------------------------------- 515 */ 516 WID_RSSI = 0x001F, 517 518 /* 519 * Join Request 520 * ----------------------------------------------------------- 521 * Configuration : Request to join 522 * Values to set : index of scan result 523 * ----------------------------------------------------------- 524 */ 525 WID_JOIN_REQ = 0x0020, 526 527 WID_LINKSPEED = 0x0026, 528 529 /* 530 * Enable User Control of TX Power 531 * ----------------------------------------------------------- 532 * Configuration : Disable Enable 533 * Values to set : 0 1 534 * ----------------------------------------------------------- 535 */ 536 WID_USER_CONTROL_ON_TX_POWER = 0x0027, 537 538 WID_MEMORY_ACCESS_8BIT = 0x0029, 539 540 /* 541 * Enable Auto RX Sensitivity feature 542 * ----------------------------------------------------------- 543 * Configuration : Disable Enable 544 * Values to set : 0 1 545 * ----------------------------------------------------------- 546 */ 547 WID_AUTO_RX_SENSITIVITY = 0x0032, 548 549 /* 550 * Receive Buffer Based Ack 551 * ----------------------------------------------------------- 552 * Configuration : Disable Enable 553 * Values to set : 0 1 554 * ----------------------------------------------------------- 555 */ 556 WID_DATAFLOW_CONTROL = 0x0033, 557 558 /* 559 * Scan Filter 560 * ----------------------------------------------------------- 561 * Configuration : Class No filter AP only Station Only 562 * Values to set : 0 1 2 563 * Configuration : Priority High Rssi Low Rssi Detect 564 * Values to set : 0 0x4 0x0 565 * Configuration : Channel filter off filter on 566 * Values to set : 0 0x10 567 * ----------------------------------------------------------- 568 */ 569 WID_SCAN_FILTER = 0x0036, 570 571 /* 572 * Link Loss Threshold (measure in the beacon period) 573 * ----------------------------------------------------------- 574 * Configuration : Any value between 10 and 254(Set to 255 disable) 575 * Values to set : Same value. Default is 10 576 * ----------------------------------------------------------- 577 */ 578 WID_LINK_LOSS_THRESHOLD = 0x0037, 579 580 WID_ABORT_RUNNING_SCAN = 0x003E, 581 582 /* NMAC Character WID list */ 583 WID_WPS_START = 0x0043, 584 585 /* 586 * Protection mode for MAC 587 * ----------------------------------------------------------- 588 * Configuration : Auto No protection ERP HT GF 589 * Values to set : 0 1 2 3 4 590 * ----------------------------------------------------------- 591 */ 592 WID_11N_PROT_MECH = 0x0080, 593 594 /* 595 * ERP Protection type for MAC 596 * ----------------------------------------------------------- 597 * Configuration : Self-CTS RTS-CTS 598 * Values to set : 0 1 599 * ----------------------------------------------------------- 600 */ 601 WID_11N_ERP_PROT_TYPE = 0x0081, 602 603 /* 604 * HT Option Enable 605 * ----------------------------------------------------------- 606 * Configuration : HT Enable HT Disable 607 * Values to set : 1 0 608 * ----------------------------------------------------------- 609 */ 610 WID_11N_ENABLE = 0x0082, 611 612 /* 613 * 11n Operating mode (Note that 11g operating mode will also be 614 * used in addition to this, if this is set to HT Mixed mode) 615 * ----------------------------------------------------------- 616 * Configuration : HT Mixed HT Only-20MHz HT Only-20/40MHz 617 * Values to set : 1 2 3 618 * ----------------------------------------------------------- 619 */ 620 WID_11N_OPERATING_MODE = 0x0083, 621 622 /* 623 * 11n OBSS non-HT STA Detection flag 624 * ----------------------------------------------------------- 625 * Configuration : Do not detect 626 * Values to set : 0 627 * Configuration : Detect, do not protect or report 628 * Values to set : 1 629 * Configuration : Detect, protect and do not report 630 * Values to set : 2 631 * Configuration : Detect, protect and report to other BSS 632 * Values to set : 3 633 * ----------------------------------------------------------- 634 */ 635 WID_11N_OBSS_NONHT_DETECTION = 0x0084, 636 637 /* 638 * 11n HT Protection Type 639 * ----------------------------------------------------------- 640 * Configuration : RTS-CTS First Frame Exchange at non-HT-rate 641 * Values to set : 0 1 642 * Configuration : LSIG TXOP First Frame Exchange in Mixed Fmt 643 * Values to set : 2 3 644 * ----------------------------------------------------------- 645 */ 646 WID_11N_HT_PROT_TYPE = 0x0085, 647 648 /* 649 * 11n RIFS Protection Enable Flag 650 * ----------------------------------------------------------- 651 * Configuration : Disable Enable 652 * Values to set : 0 1 653 * ----------------------------------------------------------- 654 */ 655 WID_11N_RIFS_PROT_ENABLE = 0x0086, 656 657 /* 658 * SMPS Mode 659 * ----------------------------------------------------------- 660 * Configuration : Static Dynamic MIMO (Power Save Disabled) 661 * Values to set : 1 2 3 662 * ----------------------------------------------------------- 663 */ 664 WID_11N_SMPS_MODE = 0x0087, 665 666 /* 667 * Current transmit MCS 668 * ----------------------------------------------------------- 669 * Configuration : MCS Index for data rate 670 * Values to set : 0 to 7 671 * ----------------------------------------------------------- 672 */ 673 WID_11N_CURRENT_TX_MCS = 0x0088, 674 675 WID_11N_PRINT_STATS = 0x0089, 676 677 /* 678 * 11n Short GI Enable Flag 679 * ----------------------------------------------------------- 680 * Configuration : Disable Enable 681 * Values to set : 0 1 682 * ----------------------------------------------------------- 683 */ 684 WID_11N_SHORT_GI_ENABLE = 0x008D, 685 686 /* 687 * 11n RIFS Enable Flag 688 * ----------------------------------------------------------- 689 * Configuration : Disable Enable 690 * Values to set : 0 1 691 * ----------------------------------------------------------- 692 */ 693 WID_RIFS_MODE = 0x0094, 694 695 /* 696 * TX Abort Feature 697 * ----------------------------------------------------------- 698 * Configuration : Disable Self CTS Enable Self CTS 699 * Values to set : 0 1 700 * Configuration : Disable TX Abort Enable TX Abort 701 * Values to set : 2 3 702 * Configuration : Enable HW TX Abort Enable SW TX Abort 703 * Values to set : 4 5 704 * ----------------------------------------------------------- 705 */ 706 WID_TX_ABORT_CONFIG = 0x00A1, 707 708 WID_REG_TSSI_11B_VALUE = 0x00A6, 709 WID_REG_TSSI_11G_VALUE = 0x00A7, 710 WID_REG_TSSI_11N_VALUE = 0x00A8, 711 WID_TX_CALIBRATION = 0x00A9, 712 WID_DSCR_TSSI_11B_VALUE = 0x00AA, 713 WID_DSCR_TSSI_11G_VALUE = 0x00AB, 714 WID_DSCR_TSSI_11N_VALUE = 0x00AC, 715 716 /* 717 * Immediate Block-Ack Support 718 * ----------------------------------------------------------- 719 * Configuration : Disable Enable 720 * Values to set : 0 1 721 * ----------------------------------------------------------- 722 */ 723 WID_11N_IMMEDIATE_BA_ENABLED = 0x00AF, 724 725 /* 726 * TXOP Disable Flag 727 * ----------------------------------------------------------- 728 * Configuration : Disable Enable 729 * Values to set : 1 0 730 * ----------------------------------------------------------- 731 */ 732 WID_11N_TXOP_PROT_DISABLE = 0x00B0, 733 734 WID_TX_POWER_LEVEL_11N = 0x00B1, 735 736 /* Custom Character WID list */ 737 WID_PC_TEST_MODE = 0x00C8, 738 /* SCAN Complete notification WID*/ 739 WID_SCAN_COMPLETE = 0x00C9, 740 741 WID_DEL_BEACON = 0x00CA, 742 743 WID_LOGTerminal_Switch = 0x00CD, 744 WID_TX_POWER = 0x00CE, 745 /* EMAC Short WID list */ 746 /* RTS Threshold */ 747 /* 748 * ----------------------------------------------------------- 749 * Configuration : Any value between 256 to 2347 750 * Values to set : Same value. Default is 2347 751 * ----------------------------------------------------------- 752 */ 753 WID_RTS_THRESHOLD = 0x1000, 754 755 /* 756 * Fragmentation Threshold 757 * ----------------------------------------------------------- 758 * Configuration : Any value between 256 to 2346 759 * Values to set : Same value. Default is 2346 760 * ----------------------------------------------------------- 761 */ 762 WID_FRAG_THRESHOLD = 0x1001, 763 764 WID_SHORT_RETRY_LIMIT = 0x1002, 765 WID_LONG_RETRY_LIMIT = 0x1003, 766 WID_BEACON_INTERVAL = 0x1006, 767 WID_MEMORY_ACCESS_16BIT = 0x1008, 768 WID_RX_SENSE = 0x100B, 769 WID_ACTIVE_SCAN_TIME = 0x100C, 770 WID_PASSIVE_SCAN_TIME = 0x100D, 771 772 WID_SITE_SURVEY_SCAN_TIME = 0x100E, 773 WID_JOIN_START_TIMEOUT = 0x100F, 774 WID_AUTH_TIMEOUT = 0x1010, 775 WID_ASOC_TIMEOUT = 0x1011, 776 WID_11I_PROTOCOL_TIMEOUT = 0x1012, 777 WID_EAPOL_RESPONSE_TIMEOUT = 0x1013, 778 779 /* NMAC Short WID list */ 780 WID_11N_SIG_QUAL_VAL = 0x1085, 781 WID_CCA_THRESHOLD = 0x1087, 782 783 /* Custom Short WID list */ 784 785 /* EMAC Integer WID list */ 786 WID_FAILED_COUNT = 0x2000, 787 WID_RETRY_COUNT = 0x2001, 788 WID_MULTIPLE_RETRY_COUNT = 0x2002, 789 WID_FRAME_DUPLICATE_COUNT = 0x2003, 790 WID_ACK_FAILURE_COUNT = 0x2004, 791 WID_RECEIVED_FRAGMENT_COUNT = 0x2005, 792 WID_MCAST_RECEIVED_FRAME_COUNT = 0x2006, 793 WID_FCS_ERROR_COUNT = 0x2007, 794 WID_SUCCESS_FRAME_COUNT = 0x2008, 795 WID_HUT_TX_COUNT = 0x200A, 796 WID_TX_FRAGMENT_COUNT = 0x200B, 797 WID_TX_MULTICAST_FRAME_COUNT = 0x200C, 798 WID_RTS_SUCCESS_COUNT = 0x200D, 799 WID_RTS_FAILURE_COUNT = 0x200E, 800 WID_WEP_UNDECRYPTABLE_COUNT = 0x200F, 801 WID_REKEY_PERIOD = 0x2010, 802 WID_REKEY_PACKET_COUNT = 0x2011, 803 WID_1X_SERV_ADDR = 0x2012, 804 WID_STACK_IP_ADDR = 0x2013, 805 WID_STACK_NETMASK_ADDR = 0x2014, 806 WID_HW_RX_COUNT = 0x2015, 807 WID_MEMORY_ADDRESS = 0x201E, 808 WID_MEMORY_ACCESS_32BIT = 0x201F, 809 WID_RF_REG_VAL = 0x2021, 810 811 /* NMAC Integer WID list */ 812 WID_11N_PHY_ACTIVE_REG_VAL = 0x2080, 813 814 /* Custom Integer WID list */ 815 WID_GET_INACTIVE_TIME = 0x2084, 816 WID_SET_OPERATION_MODE = 0X2086, 817 /* EMAC String WID list */ 818 WID_SSID = 0x3000, 819 WID_FIRMWARE_VERSION = 0x3001, 820 WID_OPERATIONAL_RATE_SET = 0x3002, 821 WID_BSSID = 0x3003, 822 WID_WEP_KEY_VALUE = 0x3004, 823 WID_11I_PSK = 0x3008, 824 WID_11E_P_ACTION_REQ = 0x3009, 825 WID_1X_KEY = 0x300A, 826 WID_HARDWARE_VERSION = 0x300B, 827 WID_MAC_ADDR = 0x300C, 828 WID_HUT_DEST_ADDR = 0x300D, 829 WID_PHY_VERSION = 0x300F, 830 WID_SUPP_USERNAME = 0x3010, 831 WID_SUPP_PASSWORD = 0x3011, 832 WID_SITE_SURVEY_RESULTS = 0x3012, 833 WID_RX_POWER_LEVEL = 0x3013, 834 WID_DEL_ALL_RX_BA = 0x3014, 835 WID_SET_STA_MAC_INACTIVE_TIME = 0x3017, 836 WID_ADD_WEP_KEY = 0x3019, 837 WID_REMOVE_WEP_KEY = 0x301A, 838 WID_ADD_PTK = 0x301B, 839 WID_ADD_RX_GTK = 0x301C, 840 WID_ADD_TX_GTK = 0x301D, 841 WID_REMOVE_KEY = 0x301E, 842 WID_ASSOC_REQ_INFO = 0x301F, 843 WID_ASSOC_RES_INFO = 0x3020, 844 WID_MANUFACTURER = 0x3026, /*Added for CAPI tool */ 845 WID_MODEL_NAME = 0x3027, /*Added for CAPI tool */ 846 WID_MODEL_NUM = 0x3028, /*Added for CAPI tool */ 847 WID_DEVICE_NAME = 0x3029, /*Added for CAPI tool */ 848 WID_SET_DRV_HANDLER = 0x3030, 849 850 /* NMAC String WID list */ 851 WID_11N_P_ACTION_REQ = 0x3080, 852 WID_HUT_TEST_ID = 0x3081, 853 WID_PMKID_INFO = 0x3082, 854 WID_FIRMWARE_INFO = 0x3083, 855 WID_REGISTER_FRAME = 0x3084, 856 WID_DEL_ALL_STA = 0x3085, 857 WID_REMAIN_ON_CHAN = 0x3996, 858 WID_SSID_PROBE_REQ = 0x3997, 859 WID_JOIN_REQ_EXTENDED = 0x3998, 860 861 WID_IP_ADDRESS = 0x3999, 862 863 /* Custom String WID list */ 864 865 /* EMAC Binary WID list */ 866 WID_UAPSD_CONFIG = 0x4001, 867 WID_UAPSD_STATUS = 0x4002, 868 WID_WMM_AP_AC_PARAMS = 0x4003, 869 WID_WMM_STA_AC_PARAMS = 0x4004, 870 WID_NETWORK_INFO = 0x4005, 871 WID_STA_JOIN_INFO = 0x4006, 872 WID_CONNECTED_STA_LIST = 0x4007, 873 874 /* NMAC Binary WID list */ 875 WID_11N_AUTORATE_TABLE = 0x4080, 876 877 WID_SCAN_CHANNEL_LIST = 0x4084, 878 879 WID_INFO_ELEMENT_PROBE = 0x4085, 880 WID_INFO_ELEMENT_ASSOCIATE = 0x4086, 881 WID_ADD_STA = 0X4087, 882 WID_REMOVE_STA = 0X4088, 883 WID_EDIT_STA = 0X4089, 884 WID_ADD_BEACON = 0x408a, 885 886 WID_SETUP_MULTICAST_FILTER = 0x408b, 887 888 /* Miscellaneous WIDs */ 889 WID_ALL = 0x7FFE, 890 WID_MAX = 0xFFFF 891 } WID_T; 892 893 struct wilc; 894 int wilc_wlan_init(struct net_device *dev); 895 u32 wilc_get_chipid(struct wilc *wilc, bool update); 896 897 #endif 898