1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /****************************************************************************** 3 * QLOGIC LINUX SOFTWARE 4 * 5 * QLogic ISP1280 (Ultra2) /12160 (Ultra3) SCSI driver 6 * Copyright (C) 2000 Qlogic Corporation 7 * (www.qlogic.com) 8 * 9 ******************************************************************************/ 10 11 #ifndef _QLA1280_H 12 #define _QLA1280_H 13 14 /* 15 * Data bit definitions. 16 */ 17 #define BIT_0 0x1 18 #define BIT_1 0x2 19 #define BIT_2 0x4 20 #define BIT_3 0x8 21 #define BIT_4 0x10 22 #define BIT_5 0x20 23 #define BIT_6 0x40 24 #define BIT_7 0x80 25 #define BIT_8 0x100 26 #define BIT_9 0x200 27 #define BIT_10 0x400 28 #define BIT_11 0x800 29 #define BIT_12 0x1000 30 #define BIT_13 0x2000 31 #define BIT_14 0x4000 32 #define BIT_15 0x8000 33 #define BIT_16 0x10000 34 #define BIT_17 0x20000 35 #define BIT_18 0x40000 36 #define BIT_19 0x80000 37 #define BIT_20 0x100000 38 #define BIT_21 0x200000 39 #define BIT_22 0x400000 40 #define BIT_23 0x800000 41 #define BIT_24 0x1000000 42 #define BIT_25 0x2000000 43 #define BIT_26 0x4000000 44 #define BIT_27 0x8000000 45 #define BIT_28 0x10000000 46 #define BIT_29 0x20000000 47 #define BIT_30 0x40000000 48 #define BIT_31 0x80000000 49 50 #if MEMORY_MAPPED_IO 51 #define RD_REG_WORD(addr) readw_relaxed(addr) 52 #define RD_REG_WORD_dmasync(addr) readw(addr) 53 #define WRT_REG_WORD(addr, data) writew(data, addr) 54 #else /* MEMORY_MAPPED_IO */ 55 #define RD_REG_WORD(addr) inw((unsigned long)addr) 56 #define RD_REG_WORD_dmasync(addr) RD_REG_WORD(addr) 57 #define WRT_REG_WORD(addr, data) outw(data, (unsigned long)addr) 58 #endif /* MEMORY_MAPPED_IO */ 59 60 /* 61 * Host adapter default definitions. 62 */ 63 #define MAX_BUSES 2 /* 2 */ 64 #define MAX_B_BITS 1 65 66 #define MAX_TARGETS 16 /* 16 */ 67 #define MAX_T_BITS 4 /* 4 */ 68 69 #define MAX_LUNS 8 /* 32 */ 70 #define MAX_L_BITS 3 /* 5 */ 71 72 /* 73 * Watchdog time quantum 74 */ 75 #define QLA1280_WDG_TIME_QUANTUM 5 /* In seconds */ 76 77 /* Command retry count (0-65535) */ 78 #define COMMAND_RETRY_COUNT 255 79 80 /* Maximum outstanding commands in ISP queues */ 81 #define MAX_OUTSTANDING_COMMANDS 512 82 #define COMPLETED_HANDLE ((unsigned char *) \ 83 (MAX_OUTSTANDING_COMMANDS + 2)) 84 85 /* ISP request and response entry counts (37-65535) */ 86 #define REQUEST_ENTRY_CNT 255 /* Number of request entries. */ 87 #define RESPONSE_ENTRY_CNT 63 /* Number of response entries. */ 88 89 /* 90 * SCSI Request Block structure (sp) that is placed 91 * on cmd->SCp location of every I/O 92 */ 93 struct srb { 94 struct list_head list; /* (8/16) LU queue */ 95 struct scsi_cmnd *cmd; /* (4/8) SCSI command block */ 96 /* NOTE: the sp->cmd will be NULL when this completion is 97 * called, so you should know the scsi_cmnd when using this */ 98 struct completion *wait; 99 dma_addr_t saved_dma_handle; /* for unmap of single transfers */ 100 uint8_t flags; /* (1) Status flags. */ 101 uint8_t dir; /* direction of transfer */ 102 }; 103 104 /* 105 * SRB flag definitions 106 */ 107 #define SRB_TIMEOUT (1 << 0) /* Command timed out */ 108 #define SRB_SENT (1 << 1) /* Command sent to ISP */ 109 #define SRB_ABORT_PENDING (1 << 2) /* Command abort sent to device */ 110 #define SRB_ABORTED (1 << 3) /* Command aborted command already */ 111 112 /* 113 * ISP I/O Register Set structure definitions. 114 */ 115 struct device_reg { 116 uint16_t id_l; /* ID low */ 117 uint16_t id_h; /* ID high */ 118 uint16_t cfg_0; /* Configuration 0 */ 119 #define ISP_CFG0_HWMSK 0x000f /* Hardware revision mask */ 120 #define ISP_CFG0_1020 BIT_0 /* ISP1020 */ 121 #define ISP_CFG0_1020A BIT_1 /* ISP1020A */ 122 #define ISP_CFG0_1040 BIT_2 /* ISP1040 */ 123 #define ISP_CFG0_1040A BIT_3 /* ISP1040A */ 124 #define ISP_CFG0_1040B BIT_4 /* ISP1040B */ 125 #define ISP_CFG0_1040C BIT_5 /* ISP1040C */ 126 uint16_t cfg_1; /* Configuration 1 */ 127 #define ISP_CFG1_F128 BIT_6 /* 128-byte FIFO threshold */ 128 #define ISP_CFG1_F64 BIT_4|BIT_5 /* 128-byte FIFO threshold */ 129 #define ISP_CFG1_F32 BIT_5 /* 128-byte FIFO threshold */ 130 #define ISP_CFG1_F16 BIT_4 /* 128-byte FIFO threshold */ 131 #define ISP_CFG1_BENAB BIT_2 /* Global Bus burst enable */ 132 #define ISP_CFG1_SXP BIT_0 /* SXP register select */ 133 uint16_t ictrl; /* Interface control */ 134 #define ISP_RESET BIT_0 /* ISP soft reset */ 135 #define ISP_EN_INT BIT_1 /* ISP enable interrupts. */ 136 #define ISP_EN_RISC BIT_2 /* ISP enable RISC interrupts. */ 137 #define ISP_FLASH_ENABLE BIT_8 /* Flash BIOS Read/Write enable */ 138 #define ISP_FLASH_UPPER BIT_9 /* Flash upper bank select */ 139 uint16_t istatus; /* Interface status */ 140 #define PCI_64BIT_SLOT BIT_14 /* PCI 64-bit slot indicator. */ 141 #define RISC_INT BIT_2 /* RISC interrupt */ 142 #define PCI_INT BIT_1 /* PCI interrupt */ 143 uint16_t semaphore; /* Semaphore */ 144 uint16_t nvram; /* NVRAM register. */ 145 #define NV_DESELECT 0 146 #define NV_CLOCK BIT_0 147 #define NV_SELECT BIT_1 148 #define NV_DATA_OUT BIT_2 149 #define NV_DATA_IN BIT_3 150 uint16_t flash_data; /* Flash BIOS data */ 151 uint16_t flash_address; /* Flash BIOS address */ 152 153 uint16_t unused_1[0x06]; 154 155 /* cdma_* and ddma_* are 1040 only */ 156 uint16_t cdma_cfg; 157 #define CDMA_CONF_SENAB BIT_3 /* SXP to DMA Data enable */ 158 #define CDMA_CONF_RIRQ BIT_2 /* RISC interrupt enable */ 159 #define CDMA_CONF_BENAB BIT_1 /* Bus burst enable */ 160 #define CDMA_CONF_DIR BIT_0 /* DMA direction (0=fifo->host 1=host->fifo) */ 161 uint16_t cdma_ctrl; 162 uint16_t cdma_status; 163 uint16_t cdma_fifo_status; 164 uint16_t cdma_count; 165 uint16_t cdma_reserved; 166 uint16_t cdma_address_count_0; 167 uint16_t cdma_address_count_1; 168 uint16_t cdma_address_count_2; 169 uint16_t cdma_address_count_3; 170 171 uint16_t unused_2[0x06]; 172 173 uint16_t ddma_cfg; 174 #define DDMA_CONF_SENAB BIT_3 /* SXP to DMA Data enable */ 175 #define DDMA_CONF_RIRQ BIT_2 /* RISC interrupt enable */ 176 #define DDMA_CONF_BENAB BIT_1 /* Bus burst enable */ 177 #define DDMA_CONF_DIR BIT_0 /* DMA direction (0=fifo->host 1=host->fifo) */ 178 uint16_t ddma_ctrl; 179 uint16_t ddma_status; 180 uint16_t ddma_fifo_status; 181 uint16_t ddma_xfer_count_low; 182 uint16_t ddma_xfer_count_high; 183 uint16_t ddma_addr_count_0; 184 uint16_t ddma_addr_count_1; 185 uint16_t ddma_addr_count_2; 186 uint16_t ddma_addr_count_3; 187 188 uint16_t unused_3[0x0e]; 189 190 uint16_t mailbox0; /* Mailbox 0 */ 191 uint16_t mailbox1; /* Mailbox 1 */ 192 uint16_t mailbox2; /* Mailbox 2 */ 193 uint16_t mailbox3; /* Mailbox 3 */ 194 uint16_t mailbox4; /* Mailbox 4 */ 195 uint16_t mailbox5; /* Mailbox 5 */ 196 uint16_t mailbox6; /* Mailbox 6 */ 197 uint16_t mailbox7; /* Mailbox 7 */ 198 199 uint16_t unused_4[0x20];/* 0x80-0xbf Gap */ 200 201 uint16_t host_cmd; /* Host command and control */ 202 #define HOST_INT BIT_7 /* host interrupt bit */ 203 #define BIOS_ENABLE BIT_0 204 205 uint16_t unused_5[0x5]; /* 0xc2-0xcb Gap */ 206 207 uint16_t gpio_data; 208 uint16_t gpio_enable; 209 210 uint16_t unused_6[0x11]; /* d0-f0 */ 211 uint16_t scsiControlPins; /* f2 */ 212 }; 213 214 #define MAILBOX_REGISTER_COUNT 8 215 216 /* 217 * ISP product identification definitions in mailboxes after reset. 218 */ 219 #define PROD_ID_1 0x4953 220 #define PROD_ID_2 0x0000 221 #define PROD_ID_2a 0x5020 222 #define PROD_ID_3 0x2020 223 #define PROD_ID_4 0x1 224 225 /* 226 * ISP host command and control register command definitions 227 */ 228 #define HC_RESET_RISC 0x1000 /* Reset RISC */ 229 #define HC_PAUSE_RISC 0x2000 /* Pause RISC */ 230 #define HC_RELEASE_RISC 0x3000 /* Release RISC from reset. */ 231 #define HC_SET_HOST_INT 0x5000 /* Set host interrupt */ 232 #define HC_CLR_HOST_INT 0x6000 /* Clear HOST interrupt */ 233 #define HC_CLR_RISC_INT 0x7000 /* Clear RISC interrupt */ 234 #define HC_DISABLE_BIOS 0x9000 /* Disable BIOS. */ 235 236 /* 237 * ISP mailbox Self-Test status codes 238 */ 239 #define MBS_FRM_ALIVE 0 /* Firmware Alive. */ 240 #define MBS_CHKSUM_ERR 1 /* Checksum Error. */ 241 #define MBS_SHADOW_LD_ERR 2 /* Shadow Load Error. */ 242 #define MBS_BUSY 4 /* Busy. */ 243 244 /* 245 * ISP mailbox command complete status codes 246 */ 247 #define MBS_CMD_CMP 0x4000 /* Command Complete. */ 248 #define MBS_INV_CMD 0x4001 /* Invalid Command. */ 249 #define MBS_HOST_INF_ERR 0x4002 /* Host Interface Error. */ 250 #define MBS_TEST_FAILED 0x4003 /* Test Failed. */ 251 #define MBS_CMD_ERR 0x4005 /* Command Error. */ 252 #define MBS_CMD_PARAM_ERR 0x4006 /* Command Parameter Error. */ 253 254 /* 255 * ISP mailbox asynchronous event status codes 256 */ 257 #define MBA_ASYNC_EVENT 0x8000 /* Asynchronous event. */ 258 #define MBA_BUS_RESET 0x8001 /* SCSI Bus Reset. */ 259 #define MBA_SYSTEM_ERR 0x8002 /* System Error. */ 260 #define MBA_REQ_TRANSFER_ERR 0x8003 /* Request Transfer Error. */ 261 #define MBA_RSP_TRANSFER_ERR 0x8004 /* Response Transfer Error. */ 262 #define MBA_WAKEUP_THRES 0x8005 /* Request Queue Wake-up. */ 263 #define MBA_TIMEOUT_RESET 0x8006 /* Execution Timeout Reset. */ 264 #define MBA_DEVICE_RESET 0x8007 /* Bus Device Reset. */ 265 #define MBA_BUS_MODE_CHANGE 0x800E /* SCSI bus mode transition. */ 266 #define MBA_SCSI_COMPLETION 0x8020 /* Completion response. */ 267 268 /* 269 * ISP mailbox commands 270 */ 271 #define MBC_NOP 0 /* No Operation */ 272 #define MBC_LOAD_RAM 1 /* Load RAM */ 273 #define MBC_EXECUTE_FIRMWARE 2 /* Execute firmware */ 274 #define MBC_DUMP_RAM 3 /* Dump RAM contents */ 275 #define MBC_WRITE_RAM_WORD 4 /* Write ram word */ 276 #define MBC_READ_RAM_WORD 5 /* Read ram word */ 277 #define MBC_MAILBOX_REGISTER_TEST 6 /* Wrap incoming mailboxes */ 278 #define MBC_VERIFY_CHECKSUM 7 /* Verify checksum */ 279 #define MBC_ABOUT_FIRMWARE 8 /* Get firmware revision */ 280 #define MBC_INIT_REQUEST_QUEUE 0x10 /* Initialize request queue */ 281 #define MBC_INIT_RESPONSE_QUEUE 0x11 /* Initialize response queue */ 282 #define MBC_EXECUTE_IOCB 0x12 /* Execute IOCB command */ 283 #define MBC_ABORT_COMMAND 0x15 /* Abort IOCB command */ 284 #define MBC_ABORT_DEVICE 0x16 /* Abort device (ID/LUN) */ 285 #define MBC_ABORT_TARGET 0x17 /* Abort target (ID) */ 286 #define MBC_BUS_RESET 0x18 /* SCSI bus reset */ 287 #define MBC_GET_RETRY_COUNT 0x22 /* Get retry count and delay */ 288 #define MBC_GET_TARGET_PARAMETERS 0x28 /* Get target parameters */ 289 #define MBC_SET_INITIATOR_ID 0x30 /* Set initiator SCSI ID */ 290 #define MBC_SET_SELECTION_TIMEOUT 0x31 /* Set selection timeout */ 291 #define MBC_SET_RETRY_COUNT 0x32 /* Set retry count and delay */ 292 #define MBC_SET_TAG_AGE_LIMIT 0x33 /* Set tag age limit */ 293 #define MBC_SET_CLOCK_RATE 0x34 /* Set clock rate */ 294 #define MBC_SET_ACTIVE_NEGATION 0x35 /* Set active negation state */ 295 #define MBC_SET_ASYNC_DATA_SETUP 0x36 /* Set async data setup time */ 296 #define MBC_SET_PCI_CONTROL 0x37 /* Set BUS control parameters */ 297 #define MBC_SET_TARGET_PARAMETERS 0x38 /* Set target parameters */ 298 #define MBC_SET_DEVICE_QUEUE 0x39 /* Set device queue parameters */ 299 #define MBC_SET_RESET_DELAY_PARAMETERS 0x3A /* Set reset delay parameters */ 300 #define MBC_SET_SYSTEM_PARAMETER 0x45 /* Set system parameter word */ 301 #define MBC_SET_FIRMWARE_FEATURES 0x4A /* Set firmware feature word */ 302 #define MBC_INIT_REQUEST_QUEUE_A64 0x52 /* Initialize request queue A64 */ 303 #define MBC_INIT_RESPONSE_QUEUE_A64 0x53 /* Initialize response q A64 */ 304 #define MBC_ENABLE_TARGET_MODE 0x55 /* Enable target mode */ 305 #define MBC_SET_DATA_OVERRUN_RECOVERY 0x5A /* Set data overrun recovery mode */ 306 307 /* 308 * ISP Get/Set Target Parameters mailbox command control flags. 309 */ 310 #define TP_PPR BIT_5 /* PPR */ 311 #define TP_RENEGOTIATE BIT_8 /* Renegotiate on error. */ 312 #define TP_STOP_QUEUE BIT_9 /* Stop que on check condition */ 313 #define TP_AUTO_REQUEST_SENSE BIT_10 /* Automatic request sense. */ 314 #define TP_TAGGED_QUEUE BIT_11 /* Tagged queuing. */ 315 #define TP_SYNC BIT_12 /* Synchronous data transfers. */ 316 #define TP_WIDE BIT_13 /* Wide data transfers. */ 317 #define TP_PARITY BIT_14 /* Parity checking. */ 318 #define TP_DISCONNECT BIT_15 /* Disconnect privilege. */ 319 320 /* 321 * NVRAM Command values. 322 */ 323 #define NV_START_BIT BIT_2 324 #define NV_WRITE_OP (BIT_26 | BIT_24) 325 #define NV_READ_OP (BIT_26 | BIT_25) 326 #define NV_ERASE_OP (BIT_26 | BIT_25 | BIT_24) 327 #define NV_MASK_OP (BIT_26 | BIT_25 | BIT_24) 328 #define NV_DELAY_COUNT 10 329 330 /* 331 * QLogic ISP1280/ISP12160 NVRAM structure definition. 332 */ 333 struct nvram { 334 uint8_t id0; /* 0 */ 335 uint8_t id1; /* 1 */ 336 uint8_t id2; /* 2 */ 337 uint8_t id3; /* 3 */ 338 uint8_t version; /* 4 */ 339 340 struct { 341 uint8_t bios_configuration_mode:2; 342 uint8_t bios_disable:1; 343 uint8_t selectable_scsi_boot_enable:1; 344 uint8_t cd_rom_boot_enable:1; 345 uint8_t disable_loading_risc_code:1; 346 uint8_t enable_64bit_addressing:1; 347 uint8_t unused_7:1; 348 } cntr_flags_1; /* 5 */ 349 350 struct { 351 uint8_t boot_lun_number:5; 352 uint8_t scsi_bus_number:1; 353 uint8_t unused_6:1; 354 uint8_t unused_7:1; 355 } cntr_flags_2l; /* 7 */ 356 357 struct { 358 uint8_t boot_target_number:4; 359 uint8_t unused_12:1; 360 uint8_t unused_13:1; 361 uint8_t unused_14:1; 362 uint8_t unused_15:1; 363 } cntr_flags_2h; /* 8 */ 364 365 uint16_t unused_8; /* 8, 9 */ 366 uint16_t unused_10; /* 10, 11 */ 367 uint16_t unused_12; /* 12, 13 */ 368 uint16_t unused_14; /* 14, 15 */ 369 370 struct { 371 uint8_t reserved:2; 372 uint8_t burst_enable:1; 373 uint8_t reserved_1:1; 374 uint8_t fifo_threshold:4; 375 } isp_config; /* 16 */ 376 377 /* Termination 378 * 0 = Disable, 1 = high only, 3 = Auto term 379 */ 380 struct { 381 uint8_t scsi_bus_1_control:2; 382 uint8_t scsi_bus_0_control:2; 383 uint8_t unused_0:1; 384 uint8_t unused_1:1; 385 uint8_t unused_2:1; 386 uint8_t auto_term_support:1; 387 } termination; /* 17 */ 388 389 uint16_t isp_parameter; /* 18, 19 */ 390 391 union { 392 uint16_t w; 393 struct { 394 uint16_t enable_fast_posting:1; 395 uint16_t report_lvd_bus_transition:1; 396 uint16_t unused_2:1; 397 uint16_t unused_3:1; 398 uint16_t disable_iosbs_with_bus_reset_status:1; 399 uint16_t disable_synchronous_backoff:1; 400 uint16_t unused_6:1; 401 uint16_t synchronous_backoff_reporting:1; 402 uint16_t disable_reselection_fairness:1; 403 uint16_t unused_9:1; 404 uint16_t unused_10:1; 405 uint16_t unused_11:1; 406 uint16_t unused_12:1; 407 uint16_t unused_13:1; 408 uint16_t unused_14:1; 409 uint16_t unused_15:1; 410 } f; 411 } firmware_feature; /* 20, 21 */ 412 413 uint16_t unused_22; /* 22, 23 */ 414 415 struct { 416 struct { 417 uint8_t initiator_id:4; 418 uint8_t scsi_reset_disable:1; 419 uint8_t scsi_bus_size:1; 420 uint8_t scsi_bus_type:1; 421 uint8_t unused_7:1; 422 } config_1; /* 24 */ 423 424 uint8_t bus_reset_delay; /* 25 */ 425 uint8_t retry_count; /* 26 */ 426 uint8_t retry_delay; /* 27 */ 427 428 struct { 429 uint8_t async_data_setup_time:4; 430 uint8_t req_ack_active_negation:1; 431 uint8_t data_line_active_negation:1; 432 uint8_t unused_6:1; 433 uint8_t unused_7:1; 434 } config_2; /* 28 */ 435 436 uint8_t unused_29; /* 29 */ 437 438 uint16_t selection_timeout; /* 30, 31 */ 439 uint16_t max_queue_depth; /* 32, 33 */ 440 441 uint16_t unused_34; /* 34, 35 */ 442 uint16_t unused_36; /* 36, 37 */ 443 uint16_t unused_38; /* 38, 39 */ 444 445 struct { 446 struct { 447 uint8_t renegotiate_on_error:1; 448 uint8_t stop_queue_on_check:1; 449 uint8_t auto_request_sense:1; 450 uint8_t tag_queuing:1; 451 uint8_t enable_sync:1; 452 uint8_t enable_wide:1; 453 uint8_t parity_checking:1; 454 uint8_t disconnect_allowed:1; 455 } parameter; /* 40 */ 456 457 uint8_t execution_throttle; /* 41 */ 458 uint8_t sync_period; /* 42 */ 459 460 union { /* 43 */ 461 uint8_t flags_43; 462 struct { 463 uint8_t sync_offset:4; 464 uint8_t device_enable:1; 465 uint8_t lun_disable:1; 466 uint8_t unused_6:1; 467 uint8_t unused_7:1; 468 } flags1x80; 469 struct { 470 uint8_t sync_offset:5; 471 uint8_t device_enable:1; 472 uint8_t unused_6:1; 473 uint8_t unused_7:1; 474 } flags1x160; 475 } flags; 476 union { /* PPR flags for the 1x160 controllers */ 477 uint8_t unused_44; 478 struct { 479 uint8_t ppr_options:4; 480 uint8_t ppr_bus_width:2; 481 uint8_t unused_8:1; 482 uint8_t enable_ppr:1; 483 } flags; /* 44 */ 484 } ppr_1x160; 485 uint8_t unused_45; /* 45 */ 486 } target[MAX_TARGETS]; 487 } bus[MAX_BUSES]; 488 489 uint16_t unused_248; /* 248, 249 */ 490 491 uint16_t subsystem_id[2]; /* 250, 251, 252, 253 */ 492 493 union { /* 254 */ 494 uint8_t unused_254; 495 uint8_t system_id_pointer; 496 } sysid_1x160; 497 498 uint8_t chksum; /* 255 */ 499 }; 500 501 /* 502 * ISP queue - command entry structure definition. 503 */ 504 #define MAX_CMDSZ 12 /* SCSI maximum CDB size. */ 505 struct cmd_entry { 506 uint8_t entry_type; /* Entry type. */ 507 #define COMMAND_TYPE 1 /* Command entry */ 508 uint8_t entry_count; /* Entry count. */ 509 uint8_t sys_define; /* System defined. */ 510 uint8_t entry_status; /* Entry Status. */ 511 __le32 handle; /* System handle. */ 512 uint8_t lun; /* SCSI LUN */ 513 uint8_t target; /* SCSI ID */ 514 __le16 cdb_len; /* SCSI command length. */ 515 __le16 control_flags; /* Control flags. */ 516 __le16 reserved; 517 __le16 timeout; /* Command timeout. */ 518 __le16 dseg_count; /* Data segment count. */ 519 uint8_t scsi_cdb[MAX_CMDSZ]; /* SCSI command words. */ 520 __le32 dseg_0_address; /* Data segment 0 address. */ 521 __le32 dseg_0_length; /* Data segment 0 length. */ 522 __le32 dseg_1_address; /* Data segment 1 address. */ 523 __le32 dseg_1_length; /* Data segment 1 length. */ 524 __le32 dseg_2_address; /* Data segment 2 address. */ 525 __le32 dseg_2_length; /* Data segment 2 length. */ 526 __le32 dseg_3_address; /* Data segment 3 address. */ 527 __le32 dseg_3_length; /* Data segment 3 length. */ 528 }; 529 530 /* 531 * ISP queue - continuation entry structure definition. 532 */ 533 struct cont_entry { 534 uint8_t entry_type; /* Entry type. */ 535 #define CONTINUE_TYPE 2 /* Continuation entry. */ 536 uint8_t entry_count; /* Entry count. */ 537 uint8_t sys_define; /* System defined. */ 538 uint8_t entry_status; /* Entry Status. */ 539 __le32 reserved; /* Reserved */ 540 __le32 dseg_0_address; /* Data segment 0 address. */ 541 __le32 dseg_0_length; /* Data segment 0 length. */ 542 __le32 dseg_1_address; /* Data segment 1 address. */ 543 __le32 dseg_1_length; /* Data segment 1 length. */ 544 __le32 dseg_2_address; /* Data segment 2 address. */ 545 __le32 dseg_2_length; /* Data segment 2 length. */ 546 __le32 dseg_3_address; /* Data segment 3 address. */ 547 __le32 dseg_3_length; /* Data segment 3 length. */ 548 __le32 dseg_4_address; /* Data segment 4 address. */ 549 __le32 dseg_4_length; /* Data segment 4 length. */ 550 __le32 dseg_5_address; /* Data segment 5 address. */ 551 __le32 dseg_5_length; /* Data segment 5 length. */ 552 __le32 dseg_6_address; /* Data segment 6 address. */ 553 __le32 dseg_6_length; /* Data segment 6 length. */ 554 }; 555 556 /* 557 * ISP queue - status entry structure definition. 558 */ 559 struct response { 560 uint8_t entry_type; /* Entry type. */ 561 #define STATUS_TYPE 3 /* Status entry. */ 562 uint8_t entry_count; /* Entry count. */ 563 uint8_t sys_define; /* System defined. */ 564 uint8_t entry_status; /* Entry Status. */ 565 #define RF_CONT BIT_0 /* Continuation. */ 566 #define RF_FULL BIT_1 /* Full */ 567 #define RF_BAD_HEADER BIT_2 /* Bad header. */ 568 #define RF_BAD_PAYLOAD BIT_3 /* Bad payload. */ 569 __le32 handle; /* System handle. */ 570 __le16 scsi_status; /* SCSI status. */ 571 __le16 comp_status; /* Completion status. */ 572 __le16 state_flags; /* State flags. */ 573 #define SF_TRANSFER_CMPL BIT_14 /* Transfer Complete. */ 574 #define SF_GOT_SENSE BIT_13 /* Got Sense */ 575 #define SF_GOT_STATUS BIT_12 /* Got Status */ 576 #define SF_TRANSFERRED_DATA BIT_11 /* Transferred data */ 577 #define SF_SENT_CDB BIT_10 /* Send CDB */ 578 #define SF_GOT_TARGET BIT_9 /* */ 579 #define SF_GOT_BUS BIT_8 /* */ 580 __le16 status_flags; /* Status flags. */ 581 __le16 time; /* Time. */ 582 __le16 req_sense_length;/* Request sense data length. */ 583 __le32 residual_length; /* Residual transfer length. */ 584 __le16 reserved[4]; 585 uint8_t req_sense_data[32]; /* Request sense data. */ 586 }; 587 588 /* 589 * ISP queue - marker entry structure definition. 590 */ 591 struct mrk_entry { 592 uint8_t entry_type; /* Entry type. */ 593 #define MARKER_TYPE 4 /* Marker entry. */ 594 uint8_t entry_count; /* Entry count. */ 595 uint8_t sys_define; /* System defined. */ 596 uint8_t entry_status; /* Entry Status. */ 597 __le32 reserved; 598 uint8_t lun; /* SCSI LUN */ 599 uint8_t target; /* SCSI ID */ 600 uint8_t modifier; /* Modifier (7-0). */ 601 #define MK_SYNC_ID_LUN 0 /* Synchronize ID/LUN */ 602 #define MK_SYNC_ID 1 /* Synchronize ID */ 603 #define MK_SYNC_ALL 2 /* Synchronize all ID/LUN */ 604 uint8_t reserved_1[53]; 605 }; 606 607 /* 608 * ISP queue - extended command entry structure definition. 609 * 610 * Unused by the driver! 611 */ 612 struct ecmd_entry { 613 uint8_t entry_type; /* Entry type. */ 614 #define EXTENDED_CMD_TYPE 5 /* Extended command entry. */ 615 uint8_t entry_count; /* Entry count. */ 616 uint8_t sys_define; /* System defined. */ 617 uint8_t entry_status; /* Entry Status. */ 618 uint32_t handle; /* System handle. */ 619 uint8_t lun; /* SCSI LUN */ 620 uint8_t target; /* SCSI ID */ 621 __le16 cdb_len; /* SCSI command length. */ 622 __le16 control_flags; /* Control flags. */ 623 __le16 reserved; 624 __le16 timeout; /* Command timeout. */ 625 __le16 dseg_count; /* Data segment count. */ 626 uint8_t scsi_cdb[88]; /* SCSI command words. */ 627 }; 628 629 /* 630 * ISP queue - 64-Bit addressing, command entry structure definition. 631 */ 632 typedef struct { 633 uint8_t entry_type; /* Entry type. */ 634 #define COMMAND_A64_TYPE 9 /* Command A64 entry */ 635 uint8_t entry_count; /* Entry count. */ 636 uint8_t sys_define; /* System defined. */ 637 uint8_t entry_status; /* Entry Status. */ 638 __le32 handle; /* System handle. */ 639 uint8_t lun; /* SCSI LUN */ 640 uint8_t target; /* SCSI ID */ 641 __le16 cdb_len; /* SCSI command length. */ 642 __le16 control_flags; /* Control flags. */ 643 __le16 reserved; 644 __le16 timeout; /* Command timeout. */ 645 __le16 dseg_count; /* Data segment count. */ 646 uint8_t scsi_cdb[MAX_CMDSZ]; /* SCSI command words. */ 647 __le32 reserved_1[2]; /* unused */ 648 __le32 dseg_0_address[2]; /* Data segment 0 address. */ 649 __le32 dseg_0_length; /* Data segment 0 length. */ 650 __le32 dseg_1_address[2]; /* Data segment 1 address. */ 651 __le32 dseg_1_length; /* Data segment 1 length. */ 652 } cmd_a64_entry_t, request_t; 653 654 /* 655 * ISP queue - 64-Bit addressing, continuation entry structure definition. 656 */ 657 struct cont_a64_entry { 658 uint8_t entry_type; /* Entry type. */ 659 #define CONTINUE_A64_TYPE 0xA /* Continuation A64 entry. */ 660 uint8_t entry_count; /* Entry count. */ 661 uint8_t sys_define; /* System defined. */ 662 uint8_t entry_status; /* Entry Status. */ 663 __le32 dseg_0_address[2]; /* Data segment 0 address. */ 664 __le32 dseg_0_length; /* Data segment 0 length. */ 665 __le32 dseg_1_address[2]; /* Data segment 1 address. */ 666 __le32 dseg_1_length; /* Data segment 1 length. */ 667 __le32 dseg_2_address[2]; /* Data segment 2 address. */ 668 __le32 dseg_2_length; /* Data segment 2 length. */ 669 __le32 dseg_3_address[2]; /* Data segment 3 address. */ 670 __le32 dseg_3_length; /* Data segment 3 length. */ 671 __le32 dseg_4_address[2]; /* Data segment 4 address. */ 672 __le32 dseg_4_length; /* Data segment 4 length. */ 673 }; 674 675 /* 676 * ISP queue - enable LUN entry structure definition. 677 */ 678 struct elun_entry { 679 uint8_t entry_type; /* Entry type. */ 680 #define ENABLE_LUN_TYPE 0xB /* Enable LUN entry. */ 681 uint8_t entry_count; /* Entry count. */ 682 uint8_t reserved_1; 683 uint8_t entry_status; /* Entry Status not used. */ 684 __le32 reserved_2; 685 __le16 lun; /* Bit 15 is bus number. */ 686 __le16 reserved_4; 687 __le32 option_flags; 688 uint8_t status; 689 uint8_t reserved_5; 690 uint8_t command_count; /* Number of ATIOs allocated. */ 691 uint8_t immed_notify_count; /* Number of Immediate Notify */ 692 /* entries allocated. */ 693 uint8_t group_6_length; /* SCSI CDB length for group 6 */ 694 /* commands (2-26). */ 695 uint8_t group_7_length; /* SCSI CDB length for group 7 */ 696 /* commands (2-26). */ 697 __le16 timeout; /* 0 = 30 seconds, 0xFFFF = disable */ 698 __le16 reserved_6[20]; 699 }; 700 701 /* 702 * ISP queue - modify LUN entry structure definition. 703 * 704 * Unused by the driver! 705 */ 706 struct modify_lun_entry { 707 uint8_t entry_type; /* Entry type. */ 708 #define MODIFY_LUN_TYPE 0xC /* Modify LUN entry. */ 709 uint8_t entry_count; /* Entry count. */ 710 uint8_t reserved_1; 711 uint8_t entry_status; /* Entry Status. */ 712 __le32 reserved_2; 713 uint8_t lun; /* SCSI LUN */ 714 uint8_t reserved_3; 715 uint8_t operators; 716 uint8_t reserved_4; 717 __le32 option_flags; 718 uint8_t status; 719 uint8_t reserved_5; 720 uint8_t command_count; /* Number of ATIOs allocated. */ 721 uint8_t immed_notify_count; /* Number of Immediate Notify */ 722 /* entries allocated. */ 723 __le16 reserved_6; 724 __le16 timeout; /* 0 = 30 seconds, 0xFFFF = disable */ 725 __le16 reserved_7[20]; 726 }; 727 728 /* 729 * ISP queue - immediate notify entry structure definition. 730 */ 731 struct notify_entry { 732 uint8_t entry_type; /* Entry type. */ 733 #define IMMED_NOTIFY_TYPE 0xD /* Immediate notify entry. */ 734 uint8_t entry_count; /* Entry count. */ 735 uint8_t reserved_1; 736 uint8_t entry_status; /* Entry Status. */ 737 __le32 reserved_2; 738 uint8_t lun; 739 uint8_t initiator_id; 740 uint8_t reserved_3; 741 uint8_t target_id; 742 __le32 option_flags; 743 uint8_t status; 744 uint8_t reserved_4; 745 uint8_t tag_value; /* Received queue tag message value */ 746 uint8_t tag_type; /* Received queue tag message type */ 747 /* entries allocated. */ 748 __le16 seq_id; 749 uint8_t scsi_msg[8]; /* SCSI message not handled by ISP */ 750 __le16 reserved_5[8]; 751 uint8_t sense_data[18]; 752 }; 753 754 /* 755 * ISP queue - notify acknowledge entry structure definition. 756 */ 757 struct nack_entry { 758 uint8_t entry_type; /* Entry type. */ 759 #define NOTIFY_ACK_TYPE 0xE /* Notify acknowledge entry. */ 760 uint8_t entry_count; /* Entry count. */ 761 uint8_t reserved_1; 762 uint8_t entry_status; /* Entry Status. */ 763 __le32 reserved_2; 764 uint8_t lun; 765 uint8_t initiator_id; 766 uint8_t reserved_3; 767 uint8_t target_id; 768 __le32 option_flags; 769 uint8_t status; 770 uint8_t event; 771 __le16 seq_id; 772 __le16 reserved_4[22]; 773 }; 774 775 /* 776 * ISP queue - Accept Target I/O (ATIO) entry structure definition. 777 */ 778 struct atio_entry { 779 uint8_t entry_type; /* Entry type. */ 780 #define ACCEPT_TGT_IO_TYPE 6 /* Accept target I/O entry. */ 781 uint8_t entry_count; /* Entry count. */ 782 uint8_t reserved_1; 783 uint8_t entry_status; /* Entry Status. */ 784 __le32 reserved_2; 785 uint8_t lun; 786 uint8_t initiator_id; 787 uint8_t cdb_len; 788 uint8_t target_id; 789 __le32 option_flags; 790 uint8_t status; 791 uint8_t scsi_status; 792 uint8_t tag_value; /* Received queue tag message value */ 793 uint8_t tag_type; /* Received queue tag message type */ 794 uint8_t cdb[26]; 795 uint8_t sense_data[18]; 796 }; 797 798 /* 799 * ISP queue - Continue Target I/O (CTIO) entry structure definition. 800 */ 801 struct ctio_entry { 802 uint8_t entry_type; /* Entry type. */ 803 #define CONTINUE_TGT_IO_TYPE 7 /* CTIO entry */ 804 uint8_t entry_count; /* Entry count. */ 805 uint8_t reserved_1; 806 uint8_t entry_status; /* Entry Status. */ 807 __le32 reserved_2; 808 uint8_t lun; /* SCSI LUN */ 809 uint8_t initiator_id; 810 uint8_t reserved_3; 811 uint8_t target_id; 812 __le32 option_flags; 813 uint8_t status; 814 uint8_t scsi_status; 815 uint8_t tag_value; /* Received queue tag message value */ 816 uint8_t tag_type; /* Received queue tag message type */ 817 __le32 transfer_length; 818 __le32 residual; 819 __le16 timeout; /* 0 = 30 seconds, 0xFFFF = disable */ 820 __le16 dseg_count; /* Data segment count. */ 821 __le32 dseg_0_address; /* Data segment 0 address. */ 822 __le32 dseg_0_length; /* Data segment 0 length. */ 823 __le32 dseg_1_address; /* Data segment 1 address. */ 824 __le32 dseg_1_length; /* Data segment 1 length. */ 825 __le32 dseg_2_address; /* Data segment 2 address. */ 826 __le32 dseg_2_length; /* Data segment 2 length. */ 827 __le32 dseg_3_address; /* Data segment 3 address. */ 828 __le32 dseg_3_length; /* Data segment 3 length. */ 829 }; 830 831 /* 832 * ISP queue - CTIO returned entry structure definition. 833 */ 834 struct ctio_ret_entry { 835 uint8_t entry_type; /* Entry type. */ 836 #define CTIO_RET_TYPE 7 /* CTIO return entry */ 837 uint8_t entry_count; /* Entry count. */ 838 uint8_t reserved_1; 839 uint8_t entry_status; /* Entry Status. */ 840 __le32 reserved_2; 841 uint8_t lun; /* SCSI LUN */ 842 uint8_t initiator_id; 843 uint8_t reserved_3; 844 uint8_t target_id; 845 __le32 option_flags; 846 uint8_t status; 847 uint8_t scsi_status; 848 uint8_t tag_value; /* Received queue tag message value */ 849 uint8_t tag_type; /* Received queue tag message type */ 850 __le32 transfer_length; 851 __le32 residual; 852 __le16 timeout; /* 0 = 30 seconds, 0xFFFF = disable */ 853 __le16 dseg_count; /* Data segment count. */ 854 __le32 dseg_0_address; /* Data segment 0 address. */ 855 __le32 dseg_0_length; /* Data segment 0 length. */ 856 __le32 dseg_1_address; /* Data segment 1 address. */ 857 __le16 dseg_1_length; /* Data segment 1 length. */ 858 uint8_t sense_data[18]; 859 }; 860 861 /* 862 * ISP queue - CTIO A64 entry structure definition. 863 */ 864 struct ctio_a64_entry { 865 uint8_t entry_type; /* Entry type. */ 866 #define CTIO_A64_TYPE 0xF /* CTIO A64 entry */ 867 uint8_t entry_count; /* Entry count. */ 868 uint8_t reserved_1; 869 uint8_t entry_status; /* Entry Status. */ 870 __le32 reserved_2; 871 uint8_t lun; /* SCSI LUN */ 872 uint8_t initiator_id; 873 uint8_t reserved_3; 874 uint8_t target_id; 875 __le32 option_flags; 876 uint8_t status; 877 uint8_t scsi_status; 878 uint8_t tag_value; /* Received queue tag message value */ 879 uint8_t tag_type; /* Received queue tag message type */ 880 __le32 transfer_length; 881 __le32 residual; 882 __le16 timeout; /* 0 = 30 seconds, 0xFFFF = disable */ 883 __le16 dseg_count; /* Data segment count. */ 884 __le32 reserved_4[2]; 885 __le32 dseg_0_address[2];/* Data segment 0 address. */ 886 __le32 dseg_0_length; /* Data segment 0 length. */ 887 __le32 dseg_1_address[2];/* Data segment 1 address. */ 888 __le32 dseg_1_length; /* Data segment 1 length. */ 889 }; 890 891 /* 892 * ISP queue - CTIO returned entry structure definition. 893 */ 894 struct ctio_a64_ret_entry { 895 uint8_t entry_type; /* Entry type. */ 896 #define CTIO_A64_RET_TYPE 0xF /* CTIO A64 returned entry */ 897 uint8_t entry_count; /* Entry count. */ 898 uint8_t reserved_1; 899 uint8_t entry_status; /* Entry Status. */ 900 __le32 reserved_2; 901 uint8_t lun; /* SCSI LUN */ 902 uint8_t initiator_id; 903 uint8_t reserved_3; 904 uint8_t target_id; 905 __le32 option_flags; 906 uint8_t status; 907 uint8_t scsi_status; 908 uint8_t tag_value; /* Received queue tag message value */ 909 uint8_t tag_type; /* Received queue tag message type */ 910 __le32 transfer_length; 911 __le32 residual; 912 __le16 timeout; /* 0 = 30 seconds, 0xFFFF = disable */ 913 __le16 dseg_count; /* Data segment count. */ 914 __le16 reserved_4[7]; 915 uint8_t sense_data[18]; 916 }; 917 918 /* 919 * ISP request and response queue entry sizes 920 */ 921 #define RESPONSE_ENTRY_SIZE (sizeof(struct response)) 922 #define REQUEST_ENTRY_SIZE (sizeof(request_t)) 923 924 /* 925 * ISP status entry - completion status definitions. 926 */ 927 #define CS_COMPLETE 0x0 /* No errors */ 928 #define CS_INCOMPLETE 0x1 /* Incomplete transfer of cmd. */ 929 #define CS_DMA 0x2 /* A DMA direction error. */ 930 #define CS_TRANSPORT 0x3 /* Transport error. */ 931 #define CS_RESET 0x4 /* SCSI bus reset occurred */ 932 #define CS_ABORTED 0x5 /* System aborted command. */ 933 #define CS_TIMEOUT 0x6 /* Timeout error. */ 934 #define CS_DATA_OVERRUN 0x7 /* Data overrun. */ 935 #define CS_COMMAND_OVERRUN 0x8 /* Command Overrun. */ 936 #define CS_STATUS_OVERRUN 0x9 /* Status Overrun. */ 937 #define CS_BAD_MSG 0xA /* Bad msg after status phase. */ 938 #define CS_NO_MSG_OUT 0xB /* No msg out after selection. */ 939 #define CS_EXTENDED_ID 0xC /* Extended ID failed. */ 940 #define CS_IDE_MSG 0xD /* Target rejected IDE msg. */ 941 #define CS_ABORT_MSG 0xE /* Target rejected abort msg. */ 942 #define CS_REJECT_MSG 0xF /* Target rejected reject msg. */ 943 #define CS_NOP_MSG 0x10 /* Target rejected NOP msg. */ 944 #define CS_PARITY_MSG 0x11 /* Target rejected parity msg. */ 945 #define CS_DEV_RESET_MSG 0x12 /* Target rejected dev rst msg. */ 946 #define CS_ID_MSG 0x13 /* Target rejected ID msg. */ 947 #define CS_FREE 0x14 /* Unexpected bus free. */ 948 #define CS_DATA_UNDERRUN 0x15 /* Data Underrun. */ 949 #define CS_TRANACTION_1 0x18 /* Transaction error 1 */ 950 #define CS_TRANACTION_2 0x19 /* Transaction error 2 */ 951 #define CS_TRANACTION_3 0x1a /* Transaction error 3 */ 952 #define CS_INV_ENTRY_TYPE 0x1b /* Invalid entry type */ 953 #define CS_DEV_QUEUE_FULL 0x1c /* Device queue full */ 954 #define CS_PHASED_SKIPPED 0x1d /* SCSI phase skipped */ 955 #define CS_ARS_FAILED 0x1e /* ARS failed */ 956 #define CS_LVD_BUS_ERROR 0x21 /* LVD bus error */ 957 #define CS_BAD_PAYLOAD 0x80 /* Driver defined */ 958 #define CS_UNKNOWN 0x81 /* Driver defined */ 959 #define CS_RETRY 0x82 /* Driver defined */ 960 961 /* 962 * ISP target entries - Option flags bit definitions. 963 */ 964 #define OF_ENABLE_TAG BIT_1 /* Tagged queue action enable */ 965 #define OF_DATA_IN BIT_6 /* Data in to initiator */ 966 /* (data from target to initiator) */ 967 #define OF_DATA_OUT BIT_7 /* Data out from initiator */ 968 /* (data from initiator to target) */ 969 #define OF_NO_DATA (BIT_7 | BIT_6) 970 #define OF_DISC_DISABLED BIT_15 /* Disconnects disabled */ 971 #define OF_DISABLE_SDP BIT_24 /* Disable sending save data ptr */ 972 #define OF_SEND_RDP BIT_26 /* Send restore data pointers msg */ 973 #define OF_FORCE_DISC BIT_30 /* Disconnects mandatory */ 974 #define OF_SSTS BIT_31 /* Send SCSI status */ 975 976 977 /* 978 * BUS parameters/settings structure - UNUSED 979 */ 980 struct bus_param { 981 uint8_t id; /* Host adapter SCSI id */ 982 uint8_t bus_reset_delay; /* SCSI bus reset delay. */ 983 uint8_t failed_reset_count; /* number of time reset failed */ 984 uint8_t unused; 985 uint16_t device_enables; /* Device enable bits. */ 986 uint16_t lun_disables; /* LUN disable bits. */ 987 uint16_t qtag_enables; /* Tag queue enables. */ 988 uint16_t hiwat; /* High water mark per device. */ 989 uint8_t reset_marker:1; 990 uint8_t disable_scsi_reset:1; 991 uint8_t scsi_bus_dead:1; /* SCSI Bus is Dead, when 5 back to back resets failed */ 992 }; 993 994 995 struct qla_driver_setup { 996 uint32_t no_sync:1; 997 uint32_t no_wide:1; 998 uint32_t no_ppr:1; 999 uint32_t no_nvram:1; 1000 uint16_t sync_mask; 1001 uint16_t wide_mask; 1002 uint16_t ppr_mask; 1003 }; 1004 1005 1006 /* 1007 * Linux Host Adapter structure 1008 */ 1009 struct scsi_qla_host { 1010 /* Linux adapter configuration data */ 1011 struct Scsi_Host *host; /* pointer to host data */ 1012 struct scsi_qla_host *next; 1013 struct device_reg __iomem *iobase; /* Base Memory-mapped I/O address */ 1014 1015 unsigned char __iomem *mmpbase; /* memory mapped address */ 1016 unsigned long host_no; 1017 struct pci_dev *pdev; 1018 uint8_t devnum; 1019 uint8_t revision; 1020 uint8_t ports; 1021 1022 unsigned long actthreads; 1023 unsigned long isr_count; /* Interrupt count */ 1024 unsigned long spurious_int; 1025 1026 /* Outstandings ISP commands. */ 1027 struct srb *outstanding_cmds[MAX_OUTSTANDING_COMMANDS]; 1028 1029 /* BUS configuration data */ 1030 struct bus_param bus_settings[MAX_BUSES]; 1031 1032 /* Received ISP mailbox data. */ 1033 volatile uint16_t mailbox_out[MAILBOX_REGISTER_COUNT]; 1034 1035 dma_addr_t request_dma; /* Physical Address */ 1036 request_t *request_ring; /* Base virtual address */ 1037 request_t *request_ring_ptr; /* Current address. */ 1038 uint16_t req_ring_index; /* Current index. */ 1039 uint16_t req_q_cnt; /* Number of available entries. */ 1040 1041 dma_addr_t response_dma; /* Physical address. */ 1042 struct response *response_ring; /* Base virtual address */ 1043 struct response *response_ring_ptr; /* Current address. */ 1044 uint16_t rsp_ring_index; /* Current index. */ 1045 1046 struct list_head done_q; /* Done queue */ 1047 1048 struct completion *mailbox_wait; 1049 struct timer_list mailbox_timer; 1050 1051 volatile struct { 1052 uint32_t online:1; /* 0 */ 1053 uint32_t reset_marker:1; /* 1 */ 1054 uint32_t disable_host_adapter:1; /* 2 */ 1055 uint32_t reset_active:1; /* 3 */ 1056 uint32_t abort_isp_active:1; /* 4 */ 1057 uint32_t disable_risc_code_load:1; /* 5 */ 1058 } flags; 1059 1060 struct nvram nvram; 1061 int nvram_valid; 1062 1063 /* Firmware Info */ 1064 unsigned short fwstart; /* start address for F/W */ 1065 unsigned char fwver1; /* F/W version first char */ 1066 unsigned char fwver2; /* F/W version second char */ 1067 unsigned char fwver3; /* F/W version third char */ 1068 }; 1069 1070 #endif /* _QLA1280_H */ 1071