Home
last modified time | relevance | path

Searched +full:0 +full:x140 (Results 1 – 10 of 10) sorted by relevance

/Documentation/devicetree/bindings/pinctrl/
Dfsl,imx8mn-pinctrl.txt23 pinctrl-0 = <&pinctrl_uart1>;
28 reg = <0x0 0x30330000 0x0 0x10000>;
32 MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
33 MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
34 MX8MN_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140
35 MX8MN_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140
36 MX8MN_IOMUXC_SD1_DATA4_GPIO2_IO6 0x19
Dfsl,imx8mm-pinctrl.txt23 pinctrl-0 = <&pinctrl_uart1>;
28 reg = <0x0 0x30330000 0x0 0x10000>;
32 MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
33 MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
/Documentation/devicetree/bindings/arm/amlogic/
Damlogic,meson-gx-ao-secure.yaml50 reg = <0x140 0x140>;
/Documentation/devicetree/bindings/regulator/
Danatop-regulator.txt31 anatop-reg-offset = <0x140>;
34 anatop-delay-reg-offset = <0x170>;
/Documentation/devicetree/bindings/interrupt-controller/
Dbrcm,bcm7120-l2-intc.txt26 0 -----[ MUX ] ------------|==========> GIC interrupt 75
83 reg = <0xf0406800 0x8>;
85 interrupts = <0x0 0x42 0x0>, <0x0 0x40 0x0>;
86 brcm,int-map-mask = <0xeb8>, <0x140>;
87 brcm,int-fwd-mask = <0x7>;
/Documentation/RCU/
Dlockdep-splat.txt25 rcu_scheduler_active = 1, debug_locks = 0
27 #0: (&shost->scan_mutex){+.+.}, at: [<ffffffff8145efca>]
28 scsi_scan_host_selected+0x5a/0x150
30 elevator_exit+0x22/0x60
32 cfq_exit_queue+0x43/0x190
35 Pid: 1552, comm: scsi_scan_6 Not tainted 3.0.0-rc5 #17
37 [<ffffffff810abb9b>] lockdep_rcu_dereference+0xbb/0xc0
38 [<ffffffff812b6139>] __cfq_exit_single_io_context+0xe9/0x120
39 [<ffffffff812b626c>] cfq_exit_queue+0x7c/0x190
40 [<ffffffff812a5046>] elevator_exit+0x36/0x60
[all …]
/Documentation/scsi/
Daha152x.txt19 IOPORT base io address (0x340/0x140)
21 SCSI_ID scsi id of controller (0-7; default 7)
22 RECONNECT allow targets to disconnect from the bus (0/1; default 1 [on])
23 PARITY enable parity checking (0/1; default 1 [on])
24 SYNCHRONOUS enable synchronous transfers (0/1; default 1 [on])
26 EXT_TRANS: enable extended translation (0/1: default 0 [off])
/Documentation/driver-api/serial/
Drocket.rst79 > mknod /dev/ttyR0 c 46 0
102 of the following: 0x100h, 0x140h, 0x180h, 0x200h, 0x240h, 0x280h,
103 0x300h, 0x340h, 0x380h. This I/O address must be reflected in the DIP
108 I/O addresses: 0x100h, 0x140h, 0x180h, 0x1C0h, 0x200h, 0x240h, 0x280h,
109 0x2C0h, 0x300h, 0x340h, 0x380h, 0x3C0h. The I/O address used by the
131 for 0x100, it will occupy 0x100 to 0x143. This would mean that you
132 CAN NOT set the second, third or fourth board for address 0x140 since
135 blocks such as 0x180.
180 :Phone: +44 (0) 1 869 323-220
181 :FAX: +44 (0) 1 869 323-211
/Documentation/usb/
Dusbip_protocol.rst105 | 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0 |
107 | 2 | 2 | 0x8005 | Command code: Retrieve the list of exported USB |
110 | 4 | 4 | 0x00000000 | Status: unused, shall be set to 0 |
119 | 0 | 2 | 0x0100 | Binary-coded decimal USBIP version number: v1.0.0.|
121 | 2 | 2 | 0x0005 | Reply code: The list of exported USB devices. |
123 | 4 | 4 | 0x00000000 | Status: 0 for OK |
125 | 8 | 4 | n | Number of exported devices: 0 means no exported |
128 | 0x0C | | | From now on the exported n devices are described, |
139 | 0x10C | 32 | | busid: Bus ID of the exported device, string |
143 | 0x12C | 4 | | busnum |
[all …]
/Documentation/trace/
Dhistogram.rst216 field:unsigned short common_type; offset:0; size:2; signed:0;
217 field:unsigned char common_flags; offset:2; size:1; signed:0;
218 field:unsigned char common_preempt_count; offset:3; size:1; signed:0;
221 field:unsigned long call_site; offset:8; size:8; signed:0;
222 field:const void * ptr; offset:16; size:8; signed:0;
223 field:size_t bytes_req; offset:24; size:8; signed:0;
224 field:size_t bytes_alloc; offset:32; size:8; signed:0;
225 field:gfp_t gfp_flags; offset:40; size:4; signed:0;
278 Dropped: 0
295 allowed for the table (normally 0, but if not a hint that you may
[all …]