Searched full:lsb (Results 1 – 25 of 63) sorted by relevance
123
| /Documentation/devicetree/bindings/sound/ |
| D | fsl-sai.txt | 33 - lsb-first : Configures whether the LSB or the MSB is transmitted
35 the MSB is transmitted first as default, or the LSB
81 lsb-first;
|
| D | tdm-slot.txt | 23 for an active slot as default, and the default active bits are at the LSB of
27 number presents bit-0 (LSB), second presents bit-1, etc. Any non zero
|
| /Documentation/hwmon/ |
| D | ad7314.rst | 28 sensor with 1lsb = 0.25 degrees centigrade. The adt7301 and
29 adt7302 have 14 bit sensors with 1lsb = 0.03125 degrees centigrade.
|
| D | lm73.rst | 32 LSB: 0.25, 0.125, 0.0625, and 0.3125. Changing the resolution mode
41 (C/LSB) (msec) (msec)
87 resolution in degrees C per LSB.
|
| D | smsc47b397.rst | 42 and 0x61 (LSB). Currently we are using 0x480 for the HWM Base Address and
73 LSB MSB
83 Reading the tach LSB locks the tach MSB.
84 The LSB Must be read first.
89 The tach reading (TCount) is given by: (Tach MSB * 256) + (Tach LSB)
|
| /Documentation/devicetree/bindings/gpio/ |
| D | netxbig-gpio-ext.txt | 6 - addr-gpios: GPIOs representing the address register (LSB -> MSB).
7 - data-gpios: GPIOs representing the data register (LSB -> MSB).
|
| /Documentation/media/uapi/v4l/ |
| D | vidioc-g-sliced-vbi-cap.rst | 156 run-in and framing code, lsb first transmitted.
161 - Byte number 3 to 15 according to Figure 9 of ETS 300 231, lsb
167 - Two bytes in transmission order, including parity bit, lsb first
180 msb lsb msb lsb
|
| /Documentation/devicetree/bindings/thermal/ |
| D | armada-thermal.txt | 25 to "control LSB/control 0" with size of 8 (current binding). All other
26 compatibles must point to "control LSB/control 0" with size of 8.
|
| /Documentation/devicetree/bindings/rtc/ |
| D | maxim-ds1302.txt | 24 - spi-lsb-first : DS-1302 requires least significant bit first
43 spi-lsb-first;
|
| /Documentation/devicetree/bindings/spi/ |
| D | icpdas-lp8841-spi-rtc.txt | 34 - spi-lsb-first: DS-1302 requires least significant bit first
51 spi-lsb-first;
|
| D | spi-controller.yaml | 101 spi-lsb-first:
104 The device requires the LSB first mode.
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-usb-devices-usbsevseg | 15 MSB 0x06; LSB 0x3F, and
17 MSB 0x08; LSB 0xFF.
|
| D | sysfs-driver-tegra-fuse | 7 words in LSB first format. Each bit represents a single value
|
| /Documentation/usb/ |
| D | misc_usbsevseg.rst | 20 MSB 0x06; LSB 0x3f
24 MSB 0x08; LSB 0xff
|
| /Documentation/ABI/removed/ |
| D | devfs | 7 against the LSB, and can be replaced by using udev.
|
| /Documentation/devicetree/bindings/display/msm/ |
| D | mdp4.txt | 41 - qcom,lcdc-align-lsb: Boolean value indicating that LSB alignment should be
|
| /Documentation/devicetree/bindings/input/ |
| D | atmel,maxtouch.txt | 24 starting at the LSB. Linux keycodes are defined in
|
| /Documentation/devicetree/bindings/dma/ |
| D | dma-common.yaml | 32 kernel. i.e. first channel corresponds to LSB.
|
| D | brcm,bcm2835-dma.txt | 23 i.e. first channel corresponds to LSB.
|
| /Documentation/input/devices/ |
| D | iforce-protocol.rst | 64 00 X-Axis lsb
66 02 Y-Axis lsb, or gas pedal for a wheel
84 03 Address of parameter block changed (lsb)
86 05 Address of second parameter block changed (lsb)
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | gpio-fan.txt | 8 ordered MSB-->LSB.
|
| /Documentation/admin-guide/ |
| D | lcd-panel-cgram.rst | 10 illuminated pixel with LSB on the right. Lines are numbered from the
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | arm,vic.txt | 22 represents single interrupt source, starting from source 0 at LSb and ending
|
| /Documentation/driver-api/nfc/ |
| D | nfc-pn544.rst | 30 and third (LSB) bytes of the message. The maximum FW message length is
|
| /Documentation/virt/kvm/ |
| D | timekeeping.txt | 134 0001 - Set Timer 0 LSB mode for port 0x40
135 set timer to read LSB only and force MSB to zero;
139 set timer to read MSB only and force LSB to zero;
143 set timer to read / write LSB first, then MSB;
147 0101 - Set Timer 1 LSB mode for port 0x41 - as described above
152 1001 - Set Timer 2 LSB mode for port 0x42 - as described above
175 10 = LSB only
176 11 = LSB / MSB (16-bit)
|
123