Searched full:transceiver (Results 1 – 25 of 42) sorted by relevance
12
| /Documentation/devicetree/bindings/net/nfc/ |
| D | st95hf.txt | 1 * STMicroelectronics : NFC Transceiver ST95HF
3 ST NFC Transceiver is required to attach with SPI bus.
5 master with which ST95HF transceiver is physically connected.
7 to include ST95HF transceiver into the platform.
11 - reg: Address of SPI slave "ST95HF transceiver" on SPI master bus.
13 - compatible: should be "st,st95hf" for ST95HF NFC transceiver
16 transceiver.
18 - enable-gpio: GPIO line to enable ST95HF transceiver.
20 - interrupts : Standard way to define ST95HF transceiver's out
26 phandle to ST95HF transceiver's regulator supply node in DT.
|
| D | trf7970a.txt | 1 * Texas Instruments TRF7970A RFID/NFC/15693 Transceiver
|
| /Documentation/devicetree/bindings/net/can/ |
| D | can-transceiver.txt | 1 Generic CAN transceiver Device Tree binding
4 CAN transceiver typically limits the max speed in standard CAN and CAN FD
7 the "can-transceiver" node can be used.
16 Based on Texas Instrument's TCAN1042HGV CAN Transceiver
20 can-transceiver {
|
| D | m_can.txt | 47 - can-transceiver : Can-transceiver subnode describing maximum speed
49 Documentation/devicetree/bindings/net/can/can-transceiver.txt
72 can-transceiver {
|
| D | microchip,mcp251x.txt | 14 - xceiver-supply: Regulator that powers the CAN transceiver.
|
| D | holt_hi311x.txt | 12 - xceiver-supply: Regulator that powers the CAN transceiver.
|
| D | ti_hecc.txt | 19 - xceiver-supply: regulator that powers the CAN transceiver
|
| D | fsl-flexcan.txt | 19 - xceiver-supply: Regulator that powers the CAN transceiver
|
| /Documentation/devicetree/bindings/usb/ |
| D | isp1301.txt | 1 * NXP ISP1301 USB transceiver
8 - transceiver: phandle of isp1301 - this helps the ISP1301 driver to find the
13 isp1301: usb-transceiver@2c {
23 transceiver = <&isp1301>;
|
| D | lpc32xx-udc.txt | 11 * External USB Transceiver Interrupt (OTG ATX)
12 - transceiver: phandle of the associated ISP1301 device - this is necessary for
17 isp1301: usb-transceiver@2c {
27 transceiver = <&isp1301>;
|
| D | ohci-nxp.txt | 8 - transceiver: phandle of the associated ISP1301 device - this is necessary for
13 isp1301: usb-transceiver@2c {
23 transceiver = <&isp1301>;
|
| /Documentation/networking/device_drivers/3com/ |
| D | 3c509.txt | 41 IRQ, and transceiver settings, although this capability shouldn't generally be
48 transceiver type 3 (10base2). The flag "0x3c509" must be set to avoid conflicts
70 (b) You must be using your card's 10baseT transceiver (i.e., the RJ-45
98 (3) Available Transceiver Types
100 For versions of the driver v1.18c and above, the available transceiver types are:
102 0 transceiver type from EEPROM config (normally 10baseT); force half-duplex
107 8 transceiver type and duplex mode taken from card's EEPROM config settings
110 Prior to driver version 1.18c, only transceiver codes 0-4 were supported. Note
111 that the new transceiver codes 8 and 12 are the *only* ones that will enable
118 The transceiver type can be changed using 'ethtool'.
[all …]
|
| /Documentation/devicetree/bindings/sound/ |
| D | rockchip-spdif.txt | 1 * Rockchip SPDIF transceiver
3 The S/PDIF audio block is a stereo transceiver that allows the
|
| D | fsl,spdif.txt | 3 The Freescale S/PDIF audio block is a stereo transceiver that allows the
27 Transceiver Clock Diagram" of SoC reference manual.
|
| D | ak4118.txt | 1 AK4118 S/PDIF transceiver
|
| D | armada-370db-audio.txt | 17 2/ the S/PDIF transceiver
|
| D | imx-audio-spdif.txt | 1 Freescale i.MX audio complex with S/PDIF transceiver
|
| /Documentation/devicetree/bindings/net/ |
| D | maxim,ds26522.txt | 1 * Maxim (Dallas) DS26522 Dual T1/E1/J1 Transceiver
|
| /Documentation/devicetree/bindings/net/ieee802154/ |
| D | mrf24j40.txt | 5 or "microchip,mrf24j40mc" depends on your transceiver
|
| /Documentation/devicetree/bindings/mfd/ |
| D | retu.txt | 6 USB transceiver functionality.
|
| D | omap-usb-tll.txt | 1 OMAP HS USB Host TLL (Transceiver-Less Interface)
|
| D | twl-familly.txt | 5 USB transceiver or Audio amplifier.
|
| /Documentation/devicetree/bindings/extcon/ |
| D | extcon-max3355.txt | 5 integrated USB OTG dual-role transceiver to function as a USB OTG dual-role
|
| /Documentation/devicetree/bindings/serial/ |
| D | fsl-imx-uart.txt | 15 the transceiver is actually CTS_B, not RTS_B. CTS_B is always output,
|
| /Documentation/devicetree/bindings/phy/ |
| D | qcom,usb-8x16-phy.txt | 1 Qualcomm's APQ8016/MSM8916 USB transceiver controller
|
12