Searched full:adjust (Results 1 – 25 of 96) sorted by relevance
1234
| /Documentation/devicetree/bindings/serial/ |
| D | nvidia,tegra20-hsuart.txt | 27 - nvidia,adjust-baud-rates: List of entries providing percentage of baud rate
46 Tx baud rate observed. To do this we use nvidia,adjust-baud-rates
56 nvidia,adjust-baud-rates = <0 9600 100>,
72 nvidia,adjust-baud-rates = <1000000 4000000 136>; /* 1.36% shift */
|
| /Documentation/media/v4l-drivers/ |
| D | radiotrack.rst | 130 radio enable, tuner adjust disable)
133 radio disable, tuner adjust disable)
139 radio enable, tuner adjust disable)
144 radio enable, tuner adjust disable)
149 radio enable, tuner adjust disable)
161 disable, "zero" bit phase 1, tuner adjust)
163 disable, "zero" bit phase 2, tuner adjust)
166 disable, "one" bit phase 1, tuner adjust)
168 disable, "one" bit phase 2, tuner adjust)
|
| /Documentation/devicetree/ |
| D | dynamic-resolution-notes.txt | 17 2. Adjust all the local phandles of the tree to resolve by that amount.
18 3. Using the __local__fixups__ node information adjust all local references
|
| /Documentation/media/uapi/v4l/ |
| D | vidioc-g-selection.rst | 74 must be filled with zeros. The driver may adjust coordinates of the
79 - ``0`` - The driver can adjust the rectangle size freely and shall
92 Please refer to :ref:`sel-const-adjust`.
103 2. Adjust width, height, left, and top to hardware limits and
126 .. _sel-const-adjust:
191 It is not possible to adjust struct :c:type:`v4l2_rect`
|
| D | selection-api-configuration.rst | 24 Therefore, as usual, drivers are expected to adjust the requested
47 The driver may further adjust the requested size and/or position
66 bounds rectangle. The driver must adjust the composing rectangle to fit
107 further adjust the requested size and/or position according to hardware
118 driver must adjust the area to fit to the bounding limits. Moreover, the
|
| D | crop.rst | 99 capture boundaries and the driver may further adjust the requested size
127 usual, drivers are expected to adjust the requested parameters and
132 signal. If the driver has to adjust both to satisfy hardware
134 driver should preferably adjust the opposite one. The
136 the driver state and therefore only adjust the requested rectangle.
|
| /Documentation/devicetree/bindings/mfd/ |
| D | allwinner,sun4i-a10-ts.yaml | 33 allwinner,tp-sensitive-adjust:
72 allwinner,tp-sensitive-adjust = <0>;
|
| /Documentation/ABI/testing/ |
| D | sysfs-driver-hid-picolcd | 31 Description: Make it possible to adjust defio refresh rate.
40 it only makes sense to adjust this value if only one or two
|
| D | sysfs-bus-iio-frequency-adf4350 | 18 adjust the reference frequency accordingly.
|
| /Documentation/bpf/ |
| D | prog_cgroup_sockopt.rst | 46 the values above, adjust ``optlen`` and reset ``retval`` to 0. If ``optlen``
78 adjust ``optval``, ``optlen`` and reset ``retval`` to 0. After that
|
| /Documentation/devicetree/bindings/power/ |
| D | ti-smartreflex.txt | 3 SmartReflex is used to set and adjust the SoC operating points.
|
| /Documentation/filesystems/ |
| D | ocfs2-online-filecheck.txt | 79 default size is 10, and can be adjust between the range of 10 ~ 100. You can
80 adjust the size like this:
|
| /Documentation/media/uapi/dvb/ |
| D | audio-set-mixer.rst | 53 This ioctl lets you adjust the mixer settings of the audio decoder.
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | fsl,mxs-pinctrl.txt | 28 one is to adjust the pin configuration for some particular pins that need a
39 there to adjust configurations for some pins in the group.
|
| /Documentation/media/uapi/rc/ |
| D | lirc-get-rec-resolution.rst | 45 used by userspace applications like lircd to automatically adjust the
|
| /Documentation/devicetree/bindings/net/ |
| D | marvell-neta-bm.txt | 15 Otherwise the driver would adjust a given number or choose default if
|
| /Documentation/devicetree/bindings/regulator/ |
| D | vctrl.txt | 23 undesiredly since the output voltage does not adjust
|
| /Documentation/sound/designs/ |
| D | powersave.rst | 26 adjust the value via sysfs on the fly. For example, to turn on the
|
| /Documentation/devicetree/bindings/opp/ |
| D | ti-omap5-opp-supply.txt | 4 contain data that can be used to adjust voltages programmed for some of their
|
| /Documentation/devicetree/bindings/spi/ |
| D | nvidia,tegra114-spi.txt | 33 with this tap value. This property is used to adjust the Tegra SPI master
|
| /Documentation/hwmon/ |
| D | adt7462.rst | 30 programmable. Once configured, the ADT7462 will adjust the PWM outputs in
|
| D | adt7470.rst | 30 programmable. Once configured, the ADT7470 will adjust the PWM outputs in
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | tpo,tpg110.yaml | 29 over the SPI interface. The interface can also adjust
|
| /Documentation/devicetree/bindings/clock/ti/ |
| D | mux.txt | 8 gate or adjust the parent rate via a divider or multiplier.
|
| /Documentation/admin-guide/laptops/ |
| D | sonypi.rst | 151 different way to adjust the backlighting of the screen. There
152 is a userspace utility to adjust the brightness on those models,
|
1234