Searched full:busy (Results 1 – 25 of 100) sorted by relevance
1234
| /Documentation/devicetree/bindings/display/ |
| D | repaper.txt | 12 - busy-gpios: BUSY pin
49 busy-gpios = <&gpio 25 0>;
|
| /Documentation/scheduler/ |
| D | sched-stats.rst | 76 of idleness (idle, busy, and newly idle):
95 cpu was busy
97 load did not require balancing when busy
99 more tasks and failed, when the cpu was busy
101 load_balance() in this domain when the cpu was busy
102 13) # of times in this domain pull_task() was called when busy
104 target task was cache-hot when busy
106 find a busier queue while the cpu was busy
108 was busy but no busier group was found
|
| /Documentation/w1/slaves/ |
| D | w1_ds28e17.rst | 52 DS28E17 devices. It is a multiplier used on the calculation of the busy
56 driver checks the DS28E17's busy flag in a loop after the precalculated
60 19-00000002dbd8: busy timeout" in the kernel log.
|
| /Documentation/ |
| D | hwspinlock.txt | 93 msecs). If the hwspinlock is already taken, the function will busy loop
101 notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs).
109 msecs). If the hwspinlock is already taken, the function will busy loop
116 notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs).
125 msecs). If the hwspinlock is already taken, the function will busy loop
133 notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs).
142 msecs). If the hwspinlock is already taken, the function will busy loop
150 notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs).
159 msecs). If the hwspinlock is already taken, the function will busy loop
166 notably -ETIMEDOUT if the hwspinlock is still busy after timeout msecs).
|
| /Documentation/process/ |
| D | volatile-considered-harmful.rst | 62 when the processor is busy-waiting on the value of a variable. The right
63 way to perform a busy wait is::
70 barrier, so, once again, volatile is unnecessary. Of course, busy-
|
| /Documentation/ABI/testing/ |
| D | sysfs-driver-w1_ds28e17 | 17 the busy timeout for I2C operations on the connected DS28E17
|
| /Documentation/ioctl/ |
| D | hdio.rst | 187 - EBUSY Controller busy
237 - EBUSY Controller busy or blockmode already set.
361 - EBUSY Controller busy
1061 - EBUSY Controller busy
1091 - EBUSY Controller busy
1119 - EBUSY Controller busy
1147 - EBUSY Controller busy
1215 the interface is busy.
1243 - EBUSY Controller busy
1271 - EBUSY Controller busy
[all …]
|
| /Documentation/timers/ |
| D | timers-howto.rst | 23 and will busy wait for enough loop cycles to achieve
45 -- Backed by busy-wait loop:
|
| /Documentation/devicetree/bindings/mtd/ |
| D | nand-controller.yaml | 47 Contains the native Ready/Busy IDs.
120 Contains the native Ready/Busy IDs.
|
| D | lpc32xx-mlc.txt | 34 nxp,busy-delay = <10000000>;
|
| D | allwinner,sun4i-a10-nand.yaml | 77 Contains the native Ready/Busy IDs.
|
| D | fsl-upm-nand.txt | 15 - gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins
|
| D | ingenic,jz4780-nand.txt | 33 - rb-gpios: GPIO specifier for the busy pin.
|
| /Documentation/hwmon/ |
| D | shtc1.rst | 55 the I2C bus will be busy during that time. By default, non-blocking mode
|
| /Documentation/admin-guide/sysctl/ |
| D | net.rst | 177 Low latency busy poll timeout for socket reads. (needs CONFIG_NET_RX_BUSY_POLL)
178 Approximate time in us to busy loop waiting for packets on the device queue.
190 Low latency busy poll timeout for poll and select. (needs CONFIG_NET_RX_BUSY_POLL)
191 Approximate time in us to busy loop waiting for events.
195 Note that only sockets with SO_BUSY_POLL set will be busy polled,
|
| /Documentation/networking/ |
| D | driver.txt | 8 transmit function will become busy.
|
| /Documentation/driver-api/thermal/ |
| D | intel_powerclamp.rst | 281 100% busy state with the disabled state.
288 If the system is not busy and has more than 25% idle time already,
292 If the system is busy (spin test below) and has less than 25% natural
|
| /Documentation/media/uapi/dvb/ |
| D | video-fopen.rst | 116 - Device or resource busy.
|
| D | audio-fopen.rst | 109 - Device or resource busy.
|
| /Documentation/ide/ |
| D | ide-tape.rst | 54 other device while the tape is busy executing a command. The
|
| D | ChangeLog.ide-floppy.1996-2002 | 57 * fix a lost interrupt problem. It appears the busy
|
| /Documentation/ABI/stable/ |
| D | sysfs-bus-xen-backend | 47 busy processing previous requests.
|
| /Documentation/media/uapi/ |
| D | gen-errors.rst | 41 - The ioctl can't be handled because the device is busy. This is
|
| /Documentation/scsi/ |
| D | qlogicfas.txt | 44 after a crash, since they may be busy trying to complete the last
|
| /Documentation/filesystems/ |
| D | autofs-mount-control.txt | 9 restarting autofs when there are busy mounts).
123 In addition, to be able to reconstruct a mount tree that has busy mounts,
358 and a forced expire that's independent of whether the mount is busy,
376 1 for busy and 0 otherwise.
|
1234