Searched full:chosen (Results 1 – 25 of 128) sorted by relevance
123456
| /Documentation/devicetree/bindings/arm/ |
| D | secure.txt | 56 The secure-chosen node
59 Similar to the /chosen node which serves as a place for passing data
60 between firmware and the operating system, the /secure-chosen node may
62 below may appear in the /secure-chosen node.
65 its console output. The syntax is the same as for /chosen/stdout-path.
66 If the /secure-chosen node exists but the stdout-path property is not
68 /secure-chosen does not exist, the Secure OS should use the value of
69 /chosen/stdout-path instead (that is, use the same device as the
|
| /Documentation/devicetree/bindings/ |
| D | chosen.txt | 1 The chosen node
4 The chosen node does not represent a real device, but serves as a place
6 arguments. Data in the chosen node does not represent the hardware.
21 chosen {
35 with a stdout-path property under /chosen, as described in the Devicetree
39 chosen {
93 chosen {
115 chosen {
133 chosen {
|
| /Documentation/devicetree/bindings/input/ |
| D | input-reset.txt | 11 The /chosen node should contain a 'linux,sysrq-reset-seq' child node to define
24 chosen {
|
| /Documentation/devicetree/bindings/regulator/ |
| D | fixed-regulator.yaml | 45 the compatible is chosen to regulator-fixed-clock. The clock binding
46 is mandatory if compatible is chosen to regulator-fixed-clock.
|
| /Documentation/security/ |
| D | IMA-templates.rst | 35 parameter. At boot time, IMA initializes the chosen template descriptor
42 descriptor chosen through the kernel configuration or through the newly
47 fields associated to the chosen template descriptor and store the result
|
| /Documentation/devicetree/bindings/arm/msm/ |
| D | ssbi.txt | 14 "pmic-arbiter". The type chosen is determined by the attached
|
| /Documentation/devicetree/bindings/display/ |
| D | simple-framebuffer.yaml | 20 sub-nodes of the chosen node (*). Simplefb nodes must be named
37 interaction, then the chosen node stdout-path property should point
159 chosen {
|
| /Documentation/ABI/testing/ |
| D | sysfs-kernel-iommu_groups | 12 file if the IOMMU driver has chosen to register a more
|
| D | sysfs-class-led | 51 scheduler is chosen. Trigger specific parameters can appear in
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | vf610-adc.txt | 21 to be chosen according to the conversion mode and the connected analog
|
| /Documentation/networking/device_drivers/mellanox/ |
| D | mlx5.rst | 36 | mlx5e is the mlx5 ulp driver which provides netdevice kernel interface, when chosen, mlx5e wil…
103 - CONFIG_PTP_1588_CLOCK: When chosen, mlx5 ptp support will be enabled
104 - CONFIG_VXLAN: When chosen, mlx5 vxaln support will be enabled.
105 - CONFIG_MLXFW: When chosen, mlx5 firmware flashing support will be enabled (via devlink and ethtoo…
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | sharp,lq101r1sx01.txt | 16 is chosen as for video mode.
|
| /Documentation/devicetree/ |
| D | usage-model.txt | 185 Most of this data is contained in the /chosen node, and when booting
188 chosen {
197 match the usual semantic of struct resource. The chosen node may also
206 is used to parse the chosen node including kernel parameters,
262 chosen { };
322 at all. The /chosen, /aliases, and /memory nodes are informational
|
| /Documentation/devicetree/bindings/net/ |
| D | marvell-neta-bm.txt | 14 to be chosen between 128 and 16352 and it also has to be aligned to 32.
|
| /Documentation/media/uapi/v4l/ |
| D | yuv-formats.rst | 21 :ref:`colorspaces` for conversion examples. YUV was chosen because
|
| /Documentation/s390/ |
| D | 3270.ChangeLog | 37 is chosen.
|
| /Documentation/leds/ |
| D | ledtrig-usbport.rst | 11 echoing "1" to a chosen port.
|
| D | leds-class.rst | 28 is chosen (via /sys/class/leds/<device>/trigger). Trigger specific
165 case the driver should give back the chosen value through delay_on and
|
| /Documentation/devicetree/bindings/leds/ |
| D | leds-is31fl319x.txt | 35 chip has a single global setting. The lowest value will be chosen
|
| /Documentation/devicetree/bindings/mfd/ |
| D | atmel-flexcom.txt | 4 controller and an USART. Only one function can be used at a time and is chosen
|
| /Documentation/devicetree/bindings/mtd/ |
| D | nvidia-tegra20-nand.txt | 38 are chosen.
|
| /Documentation/driver-api/pci/ |
| D | p2pdma.rst | 112 be chosen first. If more than one provider is an equal distance away, the
113 one returned will be chosen at random (it is not an arbitrary but
|
| /Documentation/driver-api/ |
| D | sm501.rst | 46 buffers once a display mode is chosen. Indeed when a video mode change
|
| /Documentation/admin-guide/LSM/ |
| D | tomoyo.rst | 34 Below lists are chosen from three aspects.
|
| /Documentation/admin-guide/mm/ |
| D | ksm.rst | 85 Default: 100 (chosen for demonstration purposes)
91 Default: 20 (chosen for demonstration purposes)
|
123456