Searched full:connected (Results 1 – 25 of 775) sorted by relevance
12345678910>>...31
| /Documentation/devicetree/bindings/power/ |
| D | rockchip-io-domain.txt | 57 - vccio6-supply: The supply connected to VCCIO6.
58 - vccio1-supply: The supply connected to VCCIO1.
59 - vccio2-supply: The supply connected to VCCIO2.
60 - vccio3-supply: The supply connected to VCCIO3.
61 - vccio4-supply: The supply connected to VCCIO4.
62 - vccio5-supply: The supply connected to VCCIO5.
63 - vccio-oscgpi-supply: The supply connected to VCCIO_OSCGPI.
66 - pmuio1-supply: The supply connected to PMUIO1.
67 - pmuio2-supply: The supply connected to PMUIO2.
70 - ap0-supply: The supply connected to AP0_VCC.
[all …]
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | pixcir_i2c_ts.txt | 6 - interrupts: interrupt to which the chip is connected
7 - attb-gpio: GPIO connected to the ATTB line of the chip
12 - reset-gpios: GPIO connected to the RESET line of the chip
13 - enable-gpios: GPIO connected to the ENABLE line of the chip
14 - wake-gpios: GPIO connected to the WAKE line of the chip
|
| D | zforce_ts.txt | 6 - interrupts: interrupt to which the chip is connected
7 - reset-gpios: reset gpio the chip is connected to
12 - irq-gpios : interrupt gpio the chip is connected to
|
| /Documentation/ABI/testing/ |
| D | sysfs-c2port | 30 of the connected micro.
37 access to the on-board flash of the connected micro.
45 the on-board flash block size of the connected micro.
52 the on-board flash blocks number of the connected micro.
59 the content of the on-board flash of the connected micro.
66 the "erase" command on the on-board flash of the connected
74 on-board flash size of the connected micro.
81 command on the connected micro.
88 of the connected micro.
|
| D | sysfs-bus-fsi | 6 Initiates a FSI master scan for all connected slave devices
15 link to any connnected slaves. A BREAK resets connected
25 connected slave. A terminate resets the slave's state machines
26 that control access to the internally connected engines. In
|
| /Documentation/devicetree/bindings/bus/ |
| D | ts-nbus.txt | 11 - ts,data-gpios : The 8 GPIO pins connected to the data lines on the FPGA
12 - ts,csn-gpios : The GPIO pin connected to the csn line on the FPGA
13 - ts,txrx-gpios : The GPIO pin connected to the txrx line on the FPGA
14 - ts,strobe-gpios : The GPIO pin connected to the stobe line on the FPGA
15 - ts,ale-gpios : The GPIO pin connected to the ale line on the FPGA
16 - ts,rdy-gpios : The GPIO pin connected to the rdy line on the FPGA
|
| /Documentation/devicetree/bindings/media/ |
| D | cec-gpio.txt | 13 - cec-gpios: gpio that the CEC line is connected to. The line should be
24 - hpd-gpios: gpio that the HPD line is connected to.
28 - v5-gpios: gpio that the 5V line is connected to.
30 Example for the Raspberry Pi 3 where the CEC line is connected to
32 connected to pin 11 aka BCM17 and the 5V line is connected to pin
|
| /Documentation/admin-guide/blockdev/drbd/ |
| D | conn-states-8.dot | 6 WFReportParams -> Connected [ label = "in receive_param()" ]
11 SyncSource -> Connected
12 SyncTarget -> Connected
17 Connected -> WFConnection [ label = "* on network error" ]
|
| D | drbd-connection-state-overview.dot | 29 Connected [ label=Connected,style=filled,fillcolor=green,fontcolor=black ]
66 WFReportParams -> Connected [ label="data identical\lno sync needed",color=green,fontcolor=green ]
76 cluster_resync:any -> Connected [ label="resnyc done",fontcolor=green ]
80 Connected -> CommTrouble
|
| /Documentation/devicetree/bindings/rtc/ |
| D | isil,isl12057.txt | 11 (associated with the alarm supported by the driver) is not connected
15 be set when the IRQ#2 pin of the chip is not connected to the SoC but
26 the availability of an IRQ line connected to the SoC.
29 Example isl12057 node without IRQ#2 pin connected (no alarm support):
37 Example isl12057 node with IRQ#2 pin connected to main SoC via MPP6 (note
67 Example isl12057 node without IRQ#2 pin connected to the SoC but to a
|
| /Documentation/infiniband/ |
| D | ipoib.rst | 33 Datagram vs Connected modes
37 connected. The mode is set and read through an interface's
45 In connected mode, the IB RC (Reliable Connected) transport is used.
46 Connected mode takes advantage of the connected nature of the IB
52 In connected mode, the interface's UD QP is still used for multicast
53 and communication with peers that don't support connected mode. In
114 IP over InfiniBand: Connected Mode (RFC 4755)
|
| /Documentation/devicetree/bindings/net/wireless/ |
| D | ti,wl1251.txt | 3 The wl1251 chip can be connected via SPI or via SDIO. This
4 document describes the binding for the SPI connected chip.
12 - ti,power-gpio : GPIO connected to chip's PMEN pin
15 - ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which
|
| /Documentation/devicetree/bindings/mtd/ |
| D | gpmc-onenand.txt | 1 Device tree bindings for GPMC connected OneNANDs
3 GPMC connected OneNAND (found on OMAP boards) are represented as child nodes of
13 - reg: The CS line the peripheral is connected to
14 - gpmc,device-width: Width of the ONENAND device connected to the GPMC
|
| /Documentation/devicetree/bindings/sound/ |
| D | maxim,max9759.txt | 6 - shutdown-gpios : the gpio connected to the shutdown pin
7 - mute-gpios : the gpio connected to the mute pin
8 - gain-gpios : the 2 gpios connected to the g1 and g2 pins
|
| D | everest,es7241.txt | 10 - reset-gpios: gpio connected to the reset pin
11 - m0-gpios : gpio connected to the m0 pin
12 - m1-gpios : gpio connected to the m1 pin
|
| D | wm8994.txt | 24 connected to. This is optional, if it is not connected then none
28 interrupt line connected.
53 connected.
55 connected.
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | nsa320-mcu.txt | 6 - data-gpios : The GPIO pin connected to the data line on the MCU
7 - clk-gpios : The GPIO pin connected to the clock line on the MCU
8 - act-gpios : The GPIO pin connected to the active line on the MCU
|
| /Documentation/devicetree/bindings/serio/ |
| D | allwinner,sun4i-ps2.txt | 5 and mouse can be connected.
12 - interrupts : The interrupt line connected to the PS2.
13 - clocks : The gate clk connected to the PS2.
|
| /Documentation/devicetree/bindings/input/ |
| D | samsung-keypad.txt | 22 - samsung,keypad-num-rows: Number of row lines connected to the keypad
25 - samsung,keypad-num-columns: Number of column lines connected to the
28 - Keys represented as child nodes: Each key connected to the keypad
31 - keypad,row: the row number to which the key is connected.
32 - keypad,column: the column number to which the key is connected.
|
| D | matrix-keymap.txt | 1 A simple common binding for matrix-connected key boards. Currently targeted at
14 - keypad,num-rows: Number of row lines connected to the keypad controller.
15 - keypad,num-columns: Number of column lines connected to the keypad
|
| /Documentation/devicetree/bindings/power/reset/ |
| D | ltc2952-poweroff.txt | 10 - watchdog-gpios: phandle + gpio-specifier for the GPIO connected to the
12 - kill-gpios: phandle + gpio-specifier for the GPIO connected to the
16 - trigger-gpios: phandle + gpio-specifier for the GPIO connected to the
|
| /Documentation/devicetree/bindings/auxdisplay/ |
| D | hit,hd44780.txt | 10 referring to the GPIO pins connected to the data signal lines DB0-DB7
13 connected to the "E" (Enable) signal line of the LCD Controller's bus
16 connected to the "RS" (Register Select) signal line of the LCD Controller's
23 connected to the "RW" (Read/Write) signal line of the LCD Controller's bus
|
| /Documentation/devicetree/bindings/net/nfc/ |
| D | st-nci-spi.txt | 6 - interrupts: GPIO interrupt to which the chip is connected
12 - ese-present: Specifies that an ese is physically connected to the nfc
15 connected to the nfc controller.
|
| D | st-nci-i2c.txt | 7 - interrupts: GPIO interrupt to which the chip is connected
13 - ese-present: Specifies that an ese is physically connected to the nfc
16 connected to the nfc controller.
|
| /Documentation/devicetree/bindings/clock/ |
| D | axi-clkgen.txt | 12 either reference one clock if only the first clock input is connected or two
13 if both clock inputs are connected. For the later case the clock connected
|
12345678910>>...31