Searched full:desired (Results 1 – 25 of 331) sorted by relevance
12345678910>>...14
| /Documentation/driver-api/thermal/ |
| D | power_allocator.rst | 14 2. "desired temperature" trip point: it should be higher than the
65 sustained power that can be dissipated at the desired control
67 the desired maximum temperature. The actual sustained power can vary
105 above "desired temperature" trip point). Conversely, `k_pu` is the
107 (current temperature below "desired temperature" trip point).
132 desired temperature and the current one. When the current temperature
133 is the desired one, then the proportional component is zero and
145 - T_set is the desired temperature
158 rises from the switch on temperature to the desired temperature.
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | renesas,rza2-pinctrl.txt | 44 (or a single) pin in some desired alternate function mode.
46 number and the desired function index. Use the RZA2_PINMUX macro located
49 to express the desired port pin.
|
| /Documentation/networking/ |
| D | ipv6.txt | 19 IPv6 addresses or operations are desired.
59 This might be used when no IPv6 addresses are desired.
|
| /Documentation/devicetree/bindings/clock/ |
| D | csr,atlas7-car.txt | 9 The clock consumer should specify the desired clock by having the clock
13 The reset consumer should specify the desired reset by having the reset
|
| D | efm32-clock.txt | 9 The clock consumer should specify the desired clock by having the clock ID in
|
| D | imx6sl-clock.txt | 8 The clock consumer should specify the desired clock by having the clock
|
| D | pxa-clock.txt | 7 The clock consumer should specify the desired clock by having the clock
|
| D | imx7d-clock.txt | 11 The clock consumer should specify the desired clock by having the clock
|
| D | imx6ul-clock.txt | 11 The clock consumer should specify the desired clock by having the clock
|
| D | imx6sx-clock.txt | 11 The clock consumer should specify the desired clock by having the clock
|
| D | imx8mq-clock.txt | 18 The clock consumer should specify the desired clock by having the clock
|
| D | clps711x-clock.txt | 9 The clock consumer should specify the desired clock by having the clock
|
| /Documentation/media/uapi/v4l/ |
| D | vidioc-g-parm.rst | 119 - This is the desired period between successive frames captured by
123 Applications store here the desired frame period, drivers return
142 - Applications set this field to the desired number of buffers used
172 - This is the desired period between successive frames output by the
180 Applications store here the desired frame period, drivers return
199 - Applications set this field to the desired number of buffers used
|
| /Documentation/hwmon/ |
| D | max31790.rst | 23 PWM outputs. The desired fan speeds (or PWM duty cycles) are written
40 fan[1-6]_target RW desired fan speed in RPM
|
| /Documentation/devicetree/bindings/mmc/ |
| D | rockchip-dw-mshc.txt | 37 * rockchip,desired-num-phases: The desired number of times that the host
|
| /Documentation/admin-guide/laptops/ |
| D | toshiba_haps.rst | 29 file to set the desired protection level or sensor sensibility.
40 PTLV Sets the desired protection level.
77 level, as well as set the desired protection level, the
|
| /Documentation/media/v4l-drivers/ |
| D | max2175.rst | 34 - The LO frequency position is below the desired frequency.
36 - The LO frequency position is above the desired frequency.
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | tpo,tpg110.yaml | 16 driver is strapped up in electronics to the desired resolution
27 If some electrical strap or alternate resolution is desired,
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-sirf.txt | 10 - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
|
| D | brcm,bcm2835-i2c.txt | 12 - clock-frequency : desired I2C bus clock frequency in Hz.
|
| D | i2c-wmt.txt | 12 - clock-frequency : desired I2C bus clock frequency in Hz.
|
| D | i2c-zx2967.txt | 10 - clock-frequency: the desired I2C bus clock frequency.
|
| D | i2c-hix5hd2.txt | 13 - clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000
|
| D | i2c-digicolor.txt | 12 - clock-frequency: the desired I2C bus clock frequency in Hz; in
|
| /Documentation/cpu-freq/ |
| D | pcc-cpufreq.txt | 35 1.1.2 Set Desired Frequency
76 * Set Desired Frequency
106 1.1.2 Set Desired Frequency:
109 desired frequency for a logical processor. The output buffer is currently
111 OSPM if the desired frequency was achieved or not.
|
12345678910>>...14