Searched full:determine (Results 1 – 25 of 302) sorted by relevance
12345678910>>...13
| /Documentation/pcmcia/ |
| D | devicetable.rst | 26 You can determine the hash of the product ID strings by catting the file
35 to determine the crc32 hash. Simply pass the string you want to evaluate
|
| /Documentation/ABI/testing/ |
| D | dell-smbios-wmi | 13 first determine the minimum size of the calling interface
19 To determine the size of the buffer read() a u64 dword from
|
| D | sysfs-class-regulator | 23 'unknown' means software cannot determine the state, or
27 or microamps to determine configured regulator output levels.
101 NOTE: This value should not be used to determine the regulator
116 NOTE: This value should not be used to determine the regulator
140 NOTE: This value should not be used to determine the regulator
143 attribute may be available to determine the actual mode.
371 'unknown' means software cannot determine the state, or
|
| /Documentation/devicetree/bindings/sound/ |
| D | cs35l36.txt | 32 - cirrus,multi-amp-mode : Boolean to determine if there are more than
43 - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming
46 - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the
49 - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the
|
| D | cs35l35.txt | 23 - cirrus,stereo-config : Boolean to determine if there are 2 AMPs for a
51 - cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control
66 - cirrus,amp-gain-zc : Boolean to determine if to use Amplifier gain-change
|
| /Documentation/x86/ |
| D | amd-memory-encryption.rst | 24 below on how to determine its position). The encryption bit can also be
57 determine if SME is enabled and/or to enable memory encryption::
63 If SEV is supported, MSR 0xc0010131 (MSR_AMD64_SEV) can be used to determine if
|
| /Documentation/trace/ |
| D | sys-t.rst | 34 configfs gets a few additional attributes, which determine per-source
55 ts_interval and clocksync_interval determine how much time in milliseconds
|
| /Documentation/driver-api/ |
| D | smsc_ece1099.rst | 25 In order for software to determine which device is the source
27 to determine which Status register group is a source for the interrupt.
|
| /Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/ |
| D | firmware.txt | 11 Device drivers can search this string to determine if the
|
| /Documentation/devicetree/bindings/gnss/ |
| D | mediatek.txt | 20 - gnss-fix-gpios : GPIO used to determine device position fix state
|
| D | sirfstar.txt | 30 - sirf,wakeup-gpios : GPIO used to determine device power state
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | twl-charger.txt | 10 "ti,twl4030-usb", then that is used to determine when and how
|
| /Documentation/devicetree/bindings/clock/ |
| D | armada3700-xtal-clock.txt | 3 Marvell Armada 37xx SoCs allow to determine the xtal clock frequencies by
|
| D | moxa,moxart-clock.txt | 7 MOXA ART SoCs allow to determine PLL output and APB frequencies
|
| /Documentation/spi/ |
| D | pxa2xx.rst | 31 The "pxa2xx_spi_controller.num_chipselect" field is used to determine the number of
116 to determine the correct value. An SSP configured for byte-wide transfers would
117 use a value of 8. The driver will determine a reasonable default if
218 The following logic is used to determine the type of I/O to be used on
|
| /Documentation/power/regulator/ |
| D | consumer.rst | 48 A consumer can determine if a regulator is enabled by calling::
98 regulator is enabled or disabled and should NOT be used to determine regulator
100 determine the regulator physical output voltage.
130 is enabled or disabled and should not be used to determine regulator current
|
| D | design.rst | 13 - It is not possible to automatically determine the power configuration
|
| /Documentation/devicetree/bindings/mfd/ |
| D | syscon.txt | 9 OS driver) to determine the location of the registers, and access the
|
| /Documentation/devicetree/bindings/input/ |
| D | atmel,maxtouch.txt | 29 experiment to determine which bit corresponds to which input. Use
|
| /Documentation/filesystems/ |
| D | xfs-self-describing-metadata.txt | 22 determine the root cause of a corruption problem, but it is still mainly a
54 quickly determine if the metadata is intact and can be ignored for the purpose
104 determine the scope of the corruption. For example, if we have a extent btree
110 determine the scope of the problem.
127 For example, we can determine whether a metadata object is supposed to be free
241 whether the magic number can be used to determine the format of the block. In
|
| /Documentation/admin-guide/perf/ |
| D | arm_dsu_pmu.rst | 15 registers. There is no way for the driver to determine if the other events
|
| /Documentation/driver-api/mmc/ |
| D | mmc-tools.rst | 16 - Determine the eMMC writeprotect status.
|
| /Documentation/devicetree/bindings/net/ |
| D | micrel.txt | 37 input clock. Used to determine the XI input clock.
|
| /Documentation/admin-guide/device-mapper/ |
| D | zero.rst | 28 the COW device. The size of the COW device will determine the amount of real
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | brcm,bcm7038-l1-intc.txt | 21 2-5 status words to determine which IRQs are pending
|
12345678910>>...13