Searched full:displayed (Results 1 – 25 of 78) sorted by relevance
1234
| /Documentation/media/uapi/dvb/ |
| D | video-get-frame-count.rst | 54 - Returns the number of frames displayed since the decoder was
65 This ioctl call asks the Video Device to return the number of displayed
|
| D | video-stillpicture.rst | 62 NULL, then the current displayed still picture is blanked.
|
| D | video_types.rst | 203 displayed. play_state indicates if the video is currently frozen,
218 An I-frame displayed via the VIDEO_STILLPICTURE call is passed on
|
| /Documentation/media/dvb-drivers/ |
| D | bt8xx.rst | 67 1: only error messages are displayed
68 2: notifications are displayed
69 3: other useful messages are displayed
|
| /Documentation/ABI/testing/ |
| D | sysfs-platform-dell-smbios | 21 displayed.
|
| D | sysfs-firmware-qemu_fw_cfg | 30 The only legacy blob displayed is the fw_cfg device revision:
37 displayed as entries named after their unique selector key
|
| D | sysfs-bus-iio-isl29501 | 47 The value stored in sensor is displayed when read from.
|
| /Documentation/ABI/stable/ |
| D | sysfs-class-tpm | 61 Here the short, medium and long durations are displayed in
62 usecs. "[original]" indicates that the values are displayed
66 scaled to be displayed in usecs. In this case "[adjusted]"
67 will be displayed in place of "[original]".
|
| /Documentation/admin-guide/ |
| D | lockup-watchdogs.rst | 11 stack trace is displayed upon detection and, by default, the system
21 Similarly to the softlockup case, the current stack trace is displayed
|
| D | svga.rst | 39 mode list displayed may vary as the kernel version changes, because the
40 modes are listed in a "first detected -- first displayed" manner. It's
43 0x.... - Hexadecimal video mode ID (also displayed on the menu, see below
88 The modes displayed on the menu are partially sorted: The list starts with
146 but it relies on the mode being found and displayed on the menu
|
| /Documentation/block/ |
| D | switching-sched.rst | 29 will be displayed, with the currently selected scheduler in brackets::
|
| /Documentation/networking/device_drivers/neterion/ |
| D | s2io.txt | 33 In case of Xframe II, the PCI/PCI-X bus width and frequency are displayed
55 e. Statistics. Comprehensive MAC-level and software statistics displayed
|
| D | vxge.txt | 60 Comprehensive MAC-level and software statistics displayed using
|
| /Documentation/devicetree/bindings/display/panel/ |
| D | panel-common.yaml | 26 Specifies the width of the physical area where images are displayed. This
31 Specifies the height of the physical area where images are displayed. This
|
| /Documentation/media/uapi/v4l/ |
| D | selection-api-intro.rst | 29 select the part of display where the image should be displayed. The size
|
| D | dev-overlay.rst | 100 pixel is displayed, otherwise a pixel of the graphics surface.
103 video is displayed, so the graphics surface can be seen here.
220 displayed only when the bit is *set*. Pixel coordinates translate to
264 clipping rectangles are displayed.
|
| D | func-write.rst | 55 video frame, raw VBI image, sliced VPS or WSS data is displayed again.
|
| D | pixfmt-intro.rst | 27 images to the X Windows screen format when the video is to be displayed.
|
| /Documentation/scsi/ |
| D | advansys.txt | 65 driver. If an assertion fails a message will be displayed to
117 This will cause printk() messages to be be displayed on the
151 This information can be displayed with cat. For example:
|
| /Documentation/arm/ |
| D | setup.rst | 52 all the bootup messages to be displayed correctly.
|
| /Documentation/accounting/ |
| D | delay-accounting.rst | 61 commands to be run and the corresponding delay statistics to be displayed. It
|
| /Documentation/networking/device_drivers/intel/ |
| D | igb.rst | 89 This parameter adjusts the level debug messages displayed in the system logs.
169 the system log (displayed by the "dmesg" command):
|
| /Documentation/trace/ |
| D | histogram.rst | 64 output. The table displayed for a named trigger will be the same as
69 numeric fields are displayed as base-10 integers. This can be
110 currently attached hist trigger. This information is also displayed
283 the trigger info, which can also be displayed by reading the
304 information is explicitly displayed in the output, and in the
319 Finally, notice that the call_site as displayed in the output above
321 are displayed in hex. To have a numeric field displayed as a hex
365 instead. To have an address displayed as symbolic value instead,
793 id for sys_ioctl (16, displayed next to the sys_ioctl name), we
1820 output can be displayed by reading the event's 'hist' file.
[all …]
|
| /Documentation/hwmon/ |
| D | ina209.rst | 27 calibration multiplier to scale the displayed current and power values.
|
| /Documentation/fb/ |
| D | internals.rst | 68 value, and that color is displayed.
|
1234