Searched full:driving (Results 1 – 25 of 68) sorted by relevance
123
| /Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-mt8183.txt | 65 For I2C pins, there are existing generic driving setup and the specific
66 driving setup. I2C pins can only support 2/4/6/8/10/12/14/16mA driving
67 adjustment in generic driving setup. But in specific driving setup,
69 driving setup for I2C pins, the existing generic driving setup will be
71 driving setup. The specific driving setup is controlled by E1E0EN.
72 So we need add extra vendor driving preperty instead of
73 the generic driving property.
75 driving setup property. "XXX" means the value of E1E0EN. EN is 0 or 1.
76 It is used to enable or disable the specific driving setup.
|
| D | sprd,pinctrl.txt | 8 pad driving level, system control select and so on ("domain pad
9 driving level": One pin can output 3.0v or 1.8v, depending on the
10 related domain pad driving selection, if the related domain pad
|
| D | pinctrl-stmfx.txt | 31 - output-high: the pin will be configured as an output driving high level.
32 - output-low: the pin will be configured as an output driving low level.
|
| /Documentation/devicetree/bindings/power/reset/ |
| D | gpio-restart.txt | 28 - open-source : Treat the GPIO as being open source and defer driving
40 - active-delay: Delay (default 100) to wait after driving gpio active [ms]
41 - inactive-delay: Delay (default 100) to wait after driving gpio inactive [ms]
|
| D | gpio-poweroff.txt | 30 - active-delay-ms: Delay (default 100) to wait after driving gpio active
31 - inactive-delay-ms: Delay (default 100) to wait after driving gpio inactive
|
| /Documentation/devicetree/bindings/media/ |
| D | pxa-camera.txt | 11 - clock-output-names: should contain the name of the clock driving the
13 - clock-frequency: host interface is driving MCLK, and MCLK rate is this rate
|
| /Documentation/ABI/testing/ |
| D | sysfs-bus-i3c | 53 This entry describes the BCR of the master controller driving
63 This entry describes the DCR of the master controller driving
75 This entry describes the PID of the master controller driving
88 driving the bus.
95 that all devices are represented including the master driving
|
| D | sysfs-bus-iio-frequency-ad9523 | 28 Writing this file has the effect as driving the external
|
| /Documentation/devicetree/bindings/display/sunxi/ |
| D | sun4i-drm.txt | 124 - resets: phandle to the reset controller driving the PHY
140 - clocks: the clocks driving the TV encoder
141 - resets: phandle to the reset controller driving the encoder
174 - 'tcon-ch0': The clock driving the TCON channel 0, if supported
175 - resets: phandles to the reset controllers driving the encoder
197 - 'tcon-ch0': The clock driving the TCON channel 0
199 - 'tcon-ch1': The clock driving the TCON channel 1
203 - 'lvds': The reset line driving the LVDS logic
247 - resets: phandle to the reset line driving the TCON TOP
290 - resets: phandles to the reset line driving the DRC
[all …]
|
| /Documentation/devicetree/bindings/bus/ |
| D | renesas,bsc.txt | 7 SoC, driving several chip select lines, for e.g. NOR FLASH, Ethernet and USB.
13 driving the BSC must be enabled.
|
| /Documentation/driver-api/gpio/ |
| D | intro.rst | 69 MMC/SD card insertion/removal, detecting card write-protect status, driving
115 The same logic can be applied to emulate open source signaling, by driving the
119 If you are "driving" the signal high but gpiod_get_value(gpio) reports a low
121 driving the shared signal low. That's not necessarily an error. As one common
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | dongwoon,dw9714.txt | 4 for driving voice coil lenses in camera modules.
|
| /Documentation/devicetree/bindings/serial/ |
| D | brcm,bcm2835-aux-uart.txt | 8 - clocks: Clock driving the hardware; used to figure out the baud rate
|
| D | brcm,bcm6345-uart.txt | 11 - clocks: Clock driving the hardware; used to figure out the baud rate
|
| /Documentation/devicetree/bindings/soc/fsl/cpm_qe/cpm/ |
| D | brg.txt | 11 - clock-frequency : Specifies the base frequency driving
|
| /Documentation/devicetree/bindings/crypto/ |
| D | fsl-imx-scc.txt | 9 - clocks: Should contain the clock driving the SCC core.
|
| /Documentation/devicetree/bindings/iio/temperature/ |
| D | mlx90614.txt | 15 is no need for a GPIO driving the SCL line. If no GPIO is given, power
|
| /Documentation/hwmon/ |
| D | pwm-fan.rst | 14 The driver implements a simple interface for driving a fan connected to
|
| /Documentation/devicetree/bindings/watchdog/ |
| D | arm,sp805.txt | 13 - clocks: Clocks driving the watchdog timer hardware. This list should be
|
| /Documentation/devicetree/bindings/timer/ |
| D | fsl,gtm.txt | 10 - clock-frequency : specifies the frequency driving the timer.
|
| D | arm,sp804.txt | 11 - clocks: clocks driving the dual timer hardware. This list should be 1 or 3
|
| /Documentation/devicetree/bindings/arm/sunxi/ |
| D | sunxi-mbus.txt | 12 - clocks: phandle to the clock driving the controller
|
| /Documentation/devicetree/bindings/gpio/ |
| D | ni,169445-nand-gpio.txt | 20 - no-output: disables driving output on the pins
|
| D | cdns,gpio.txt | 12 - clocks: should contain one entry referencing the peripheral clock driving
|
| /Documentation/devicetree/bindings/mmc/ |
| D | hi3798cv200-dw-mshc.txt | 20 "ciu-drive" - Hi3798CV200 extended phase clock for ciu driving.
|
123