Searched full:explicitly (Results 1 – 25 of 279) sorted by relevance
12345678910>>...12
| /Documentation/ABI/stable/ |
| D | sysfs-firmware-opal-elog | 9 exist until explicitly acknowledged to firmware.
18 but not explicitly acknowledged them to firmware and
|
| /Documentation/i2c/ |
| D | instantiating-devices.rst | 8 reason, the kernel code must instantiate I2C devices explicitly. There are
92 Method 2: Instantiate the devices explicitly
100 you can instantiate your I2C devices explicitly. This is done by filling
172 explicitly. Instead, i2c-core will probe for such devices as soon as their
199 * I2C buses must now explicitly say which I2C driver classes can probe
|
| /Documentation/driver-api/ |
| D | zorro.rst | 79 explicitly using z_ioremap().
87 - Zorro III address space must be mapped explicitly using z_ioremap() first
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | ti,omap4-wugen-mpu | 21 are explicitly forbidden.
|
| D | nvidia,tegra20-ictlr.txt | 28 are explicitly forbidden.
|
| /Documentation/ |
| D | debugging-modules.txt | 22 is being loaded explicitly using "modprobe" from userspace.
|
| /Documentation/w1/masters/ |
| D | ds2482.rst | 34 detection is done. You should instantiate the device explicitly.
|
| /Documentation/ABI/testing/ |
| D | sysfs-devices-platform-ACPI-TAD | 37 is explicitly cleared via the ac_status attribute.
78 (and from S4/S5 too if supported) until its status is explicitly
|
| D | sysfs-driver-bd9571mwv-regulator | 23 DDR Backup Mode must be explicitly enabled by the user,
|
| D | sysfs-driver-hid-picolcd | 42 to flush its tiny changes explicitly at higher than default rate.
|
| /Documentation/spi/ |
| D | spi-sc18is602.rst | 22 support Chip ID registers. You will have to instantiate the devices explicitly.
|
| /Documentation/virt/kvm/ |
| D | review-checklist.txt | 15 5. New features must default to off (userspace should explicitly request them).
|
| /Documentation/hwmon/ |
| D | menf21bmc.rst | 30 You will have to instantiate the MFD driver explicitly.
|
| D | ltc4151.rst | 30 the devices explicitly.
|
| D | ltc4215.rst | 31 instantiate the devices explicitly.
|
| D | ir38064.rst | 27 devices explicitly.
|
| D | adc128d818.rst | 49 the driver explicitly if the chip is configured for any of those addresses in
|
| D | ibm-cffps.rst | 20 devices explicitly. Please see Documentation/i2c/instantiating-devices.rst for
|
| D | ltc3815.rst | 27 devices explicitly.
|
| D | ltc4260.rst | 31 the devices explicitly.
|
| /Documentation/devicetree/bindings/clock/ |
| D | maxim,max9485.txt | 25 If not explicitly set, the output names are "mclkout", "clkout", "clkout1"
|
| /Documentation/devicetree/bindings/dma/ |
| D | jz4780-dma.txt | 20 need a specific channel. These channels will only be assigned when explicitly
|
| /Documentation/filesystems/ |
| D | fuse-io.txt | 31 reclaim on memory pressure) or explicitly (invoked by close(2), fsync(2) and
|
| /Documentation/devicetree/bindings/virtio/ |
| D | iommu.txt | 7 contains a child node representing the IOMMU device explicitly.
|
| /Documentation/networking/ |
| D | defza.txt | 32 requested explicitly or if the CAM overflows. The promiscuous mode
|
12345678910>>...12