Searched full:gpio0 (Results 1 – 25 of 121) sorted by relevance
12345
| /Documentation/devicetree/bindings/bus/ |
| D | ts-nbus.txt | 31 ts,data-gpios = <&gpio0 0 GPIO_ACTIVE_HIGH
32 &gpio0 1 GPIO_ACTIVE_HIGH
33 &gpio0 2 GPIO_ACTIVE_HIGH
34 &gpio0 3 GPIO_ACTIVE_HIGH
35 &gpio0 4 GPIO_ACTIVE_HIGH
36 &gpio0 5 GPIO_ACTIVE_HIGH
37 &gpio0 6 GPIO_ACTIVE_HIGH
38 &gpio0 7 GPIO_ACTIVE_HIGH>;
39 ts,csn-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
40 ts,txrx-gpios = <&gpio0 24 GPIO_ACTIVE_HIGH>;
[all …]
|
| /Documentation/devicetree/bindings/input/ |
| D | gpio-mouse.txt | 25 up-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
26 down-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
27 left-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
28 right-gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
29 button-left-gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
30 button-middle-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
31 button-right-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/gpio/ |
| D | gpio-axp209.txt | 45 gpio0_adc: gpio0-adc {
46 pins = "GPIO0";
59 Each GPIO is independent from the other (i.e. GPIO0 in gpio_in function does
66 GPIO0 | gpio_in, gpio_out, ldo, adc
74 GPIO0 | gpio_in, gpio_out, ldo, adc
|
| D | microchip,pic32-gpio.txt | 28 gpio0: gpio0@1f860000 {
47 gpios = <&gpio0 12 0>;
|
| D | gpio-xgene.txt | 17 gpio0: gpio0@1701c000 {
|
| D | gpio-mxs.txt | 33 gpio0 = &gpio0;
44 gpio0: gpio@0 {
|
| D | wd,mbl-gpio.txt | 23 gpio0: gpio0@e0000000 {
|
| D | gpio_oxnas.txt | 28 gpio0: gpio@0 {
45 gpios = <&gpio0 12 0>;
|
| /Documentation/devicetree/bindings/hwmon/ |
| D | nsa320-mcu.txt | 17 data-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
18 clk-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
19 act-gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | colibri-vf50-ts.txt | 23 xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
25 yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
26 ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
27 interrupt-parent = <&gpio0>;
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | lt3651-charger.txt | 26 lltc,acpr-gpios = <&gpio0 68 GPIO_ACTIVE_LOW>;
27 lltc,fault-gpios = <&gpio0 64 GPIO_ACTIVE_LOW>;
28 lltc,chrg-gpios = <&gpio0 63 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/display/ |
| D | ilitek,ili9225.txt | 22 rs-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
23 reset-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
|
| D | ilitek,ili9341.txt | 23 dc-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
24 reset-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/power/reset/ |
| D | ltc2952-poweroff.txt | 26 trigger-gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
28 kill-gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/net/nfc/ |
| D | nxp-nci.txt | 30 enable-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>;
31 firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/media/i2c/ |
| D | mt9m001.txt | 29 reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
30 standby-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/gnss/ |
| D | sirfstar.txt | 43 sirf,onoff-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
44 sirf,wakeup-gpios = <&gpio0 17 GPIO_ACTIVE_HIGH>;
|
| /Documentation/devicetree/bindings/leds/ |
| D | leds-ns2.txt | 28 slow-gpio = <&gpio0 29 0>;
29 cmd-gpio = <&gpio0 30 0>;
|
| /Documentation/devicetree/bindings/net/dsa/ |
| D | realtek-smi.txt | 68 mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
69 mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
70 reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
74 interrupt-parent = <&gpio0>;
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | nuvoton,npcm7xx-pinctrl.txt | 29 gpio0: gpio@f0010000 {
44 "GPIO0/IOX1DI", "GPIO1/IOX1LD", "GPIO2/IOX1CK", "GPIO3/IOX1D0",
125 gpio0_iox1d1_pin: gpio0-iox1d1-pin {
126 pins = "GPIO0/IOX1DI";
129 gpio0_iox1ck_pin: gpio0-iox1ck-pin {
178 gpio0: gpio@f0010000 {
196 gpio0_iox1d1_pin: gpio0-iox1d1-pin {
197 pins = "GPIO0/IOX1DI";
|
| D | rockchip,pinctrl.txt | 91 gpio0: gpio0@20034000 {
140 gpio0: gpio0@2000a000 {
|
| /Documentation/devicetree/bindings/regulator/ |
| D | gpio-regulator.yaml | 107 enable-gpios = <&gpio0 23 0x4>;
108 gpios = <&gpio0 24 0x4
109 &gpio0 25 0x4>;
|
| /Documentation/devicetree/bindings/fpga/ |
| D | xilinx-slave-serial.txt | 40 done-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
41 prog_b-gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
|
| /Documentation/devicetree/bindings/net/ |
| D | btusb.txt | 31 Following example uses irq pin number 3 of gpio0 for out of band wake-on-bt:
40 interrupt-parent = <&gpio0>;
|
| /Documentation/devicetree/bindings/spi/ |
| D | snps,dw-apb-ssi.txt | 37 cs-gpios = <&gpio0 13 0>,
38 <&gpio0 14 0>;
|
12345