Searched full:indicated (Results 1 – 25 of 103) sorted by relevance
12345
| /Documentation/hwmon/ |
| D | fam15h_power.rst | 64 indicated by CPUID Fn8000_0007_EDX[12].
80 max compute unit accumulated power which is indicated by
84 compute unit accumulated power which is indicated by
87 the value of performance timestamp counter which is indicated
|
| /Documentation/devicetree/bindings/phy/ |
| D | ti,phy-am654-serdes.txt | 47 left input reference clock as indicated by <&k3_clks 153 4>, external
48 reference clock as indicated by <&k3_clks 153 1> and right input
49 reference clock as indicated by <&serdes1 AM654_SERDES_LO_REFCLK>. (The
52 SERDES0 registers 3 clock outputs as indicated in clock-output-names. The
|
| /Documentation/devicetree/bindings/mfd/ |
| D | max8925.txt | 13 - maxim,tsc-irq: there are 2 IRQ lines for max8925, one is indicated in
14 interrupts property, the other is indicated here.
|
| D | atmel-usart.txt | 5 The compatible <chip> indicated will be the first SoC to support an
|
| /Documentation/devicetree/bindings/leds/irled/ |
| D | gpio-ir-tx.txt | 8 should be indicated using flags in the GPIO specifier.
|
| /Documentation/devicetree/bindings/spi/ |
| D | jcore,spi.txt | 16 programming is relative to the frequency of the indicated clock.
|
| /Documentation/devicetree/bindings/pps/ |
| D | pps-gpio.txt | 15 - assert-falling-edge: when present, assert is indicated by a falling edge
|
| /Documentation/devicetree/bindings/sound/ |
| D | snow.txt | 17 MAX98091 or MAX98095 CODEC (exact device type is indicated by the compatible
|
| /Documentation/ABI/testing/ |
| D | configfs-usb-gadget-mass-storage | 26 removable - Flag specifying that LUN shall be indicated as
|
| D | sysfs-class-remoteproc | 45 firmware indicated by, or written to,
|
| D | sysfs-class-scsi_tape | 106 was found when the SCSI midlayer indicated that there was
|
| /Documentation/devicetree/bindings/hwlock/ |
| D | hwlock.txt | 26 associated hwlock args specifier as indicated by
|
| /Documentation/devicetree/bindings/ata/ |
| D | sata_highbank.txt | 20 indicator lights using the indicated GPIOs
|
| /Documentation/devicetree/bindings/leds/ |
| D | leds-gpio.txt | 12 indicated using flags in the GPIO specifier.
|
| /Documentation/sparc/oradax/ |
| D | dax-hv-api.txt | 24 …The DAX is a virtual device to sun4v guests, with supported data operations indicated by the virtu…
44 …The availablility of DAX coprocessor command service is indicated by the presence of the DAX virtu…
113 …desired. The number of device interrupts available to the guest is indicated in the virtual device…
236 …which are not applicable to the given CCB command should be indicated as type 0 (No address). Virt…
239 …ill result in the CCB submission being rejected, with the causal virtual address indicated. The CCB
303 … primary input data streams with fixed size elements, the element size must be indicated in the CCB
349 supported for every command. The format is indicated by a 4-bit field in the CCB:
595 …a specified range. The specific type of scan is indicated by the command code in the CCB header. F…
741 …element value to 0 on a mismatch. The specific type of translate command is indicated by the comma…
1035 …erflow indicates that the results of the operation exceeded the size of the output buffer indicated
[all …]
|
| /Documentation/devicetree/bindings/powerpc/fsl/ |
| D | pmc.txt | 19 bit assignments are indicated via the sleep specifier in each device's
|
| /Documentation/devicetree/bindings/arm/socionext/ |
| D | cache-uniphier.txt | 24 indicated correctly with "next-level-cache" properties.
|
| /Documentation/driver-api/ |
| D | libata.rst | 668 This error is indicated when STATUS value doesn't match HSM requirement
703 For ATA commands, this type of errors are indicated by !BSY && ERR
723 This is indicated by ICRC bit in the ERROR register and means that
743 This is indicated by UNC bit in the ERROR register. ATA devices
758 This is indicated by IDNF bit in the ERROR register. Report to upper
762 This can be invalid command or parameter indicated by ABRT ERROR bit
782 ATAPI device CHECK CONDITION error is indicated by set CHK bit (ERR bit)
797 NCQ command error is indicated by cleared BSY and set ERR bit during NCQ
822 over ATA bus (SATA or PATA). This type of errors can be indicated by
852 system bus). For standard BMDMA, this is indicated by Error bit in the
|
| /Documentation/admin-guide/ |
| D | devices.rst | 43 the authors as indicated above.
68 form (absolute or relative) as is indicated here. Links are
70 link; if possible, the indicated type of link should be used.
206 Each kind of device is indicated by a different letter. For any
|
| /Documentation/filesystems/ext4/ |
| D | checksums.rst | 8 The desired checksum algorithm is indicated in the superblock, though as
|
| /Documentation/filesystems/ |
| D | erofs.txt | 139 The size of the optional xattrs is indicated by i_xattr_count in inode
145 a specific block indicated by xattr_blkaddr, organized one by one with
|
| /Documentation/devicetree/bindings/net/dsa/ |
| D | marvell.txt | 30 indicated above
|
| /Documentation/devicetree/bindings/mmc/ |
| D | sdhci-cadence.txt | 12 For eMMC configuration, supported speed modes are not indicated by the SDHCI
|
| /Documentation/s390/ |
| D | monreader.rst | 164 within one data set and the end of each data set is indicated by a successful
176 As with most char devices, error conditions are indicated by returning a
|
| /Documentation/virt/kvm/devices/ |
| D | vm.txt | 119 done by a set IBC. These subfunctions are indicated to the guest VCPU via
154 Allows user space to retrieve or change cpu subfunctions to be indicated for
|
12345