Searched full:leave (Results 1 – 25 of 133) sorted by relevance
123456
| /Documentation/devicetree/bindings/usb/ |
| D | usb-device.txt | 25 may leave out all except for "usbVID,PID".
41 adhering to this binding may leave out all except for
54 may leave out all except for "usbVID,PID".
|
| /Documentation/devicetree/bindings/fpga/ |
| D | fpga-bridge.txt | 6 Default is to leave bridge in current state.
|
| /Documentation/ |
| D | futex-requeue-pi.txt | 20 implementation would wake the highest-priority waiter, and leave the
49 mutex only after it has returned to user space. This will leave the
92 The requeue code cannot simply wake the waiter and leave it to
|
| /Documentation/w1/slaves/ |
| D | w1_ds28e17.rst | 47 Valid values are 100, 400, 900 [kBaud]. Any other value means to leave
59 Leave it at 1 unless you get ETIMEDOUT errors and a "w1_slave_driver
|
| /Documentation/ABI/testing/ |
| D | sysfs-dev | 18 leave the system.
|
| D | sysfs-bus-i2c-devices-pca954x | 13 -1 - leave the mux as-is, which is the most optimal
|
| /Documentation/devicetree/bindings/power/supply/ |
| D | maxim,ds2760.txt | 18 than 2 seconds and leave sleep Mode when the DQ
|
| /Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-max77620.txt | 29 <pinctrl-bindings.txt>. Absence of properties will leave the configuration
60 Absence of this property will leave
|
| D | pinctrl-rk805.txt | 35 <pinctrl-bindings.txt>. Absence of properties will leave the configuration
|
| /Documentation/devicetree/bindings/rtc/ |
| D | isil,isl1208.txt | 24 Default will leave the non-volatile configuration of the pullup
|
| /Documentation/ABI/obsolete/ |
| D | sysfs-bus-usb | 18 If you want to suspend a device immediately but leave it
|
| /Documentation/networking/dsa/ |
| D | lan9303.rst | 29 If one of the user ports leave the bridge, the ports goes back to the initial
|
| /Documentation/devicetree/bindings/input/touchscreen/ |
| D | imx6ul_tsc.txt | 10 This xnur-gpio returns to low once the finger leave the touch screen (The
|
| /Documentation/i2c/busses/ |
| D | i2c-ali1535.rst | 38 We make sure that the SMB is enabled. We leave the ACPI alone.
|
| D | i2c-ali15x3.rst | 99 We make sure that the SMB is enabled. We leave the ACPI alone.
|
| /Documentation/devicetree/bindings/sound/ |
| D | cs42l42.txt | 24 plugged in and leave tip sense floating when not plugged in. Inverting jacks
|
| /Documentation/devicetree/bindings/regulator/ |
| D | tps65090.txt | 27 "overcurrent wait" field and we'll leave it to the BIOS/EC to deal with.
|
| /Documentation/vm/ |
| D | active_mm.rst | 29 anonymous address space we just leave the previous address space
|
| /Documentation/block/ |
| D | deadline-iosched.rst | 68 that comes at basically 0 cost we leave that on. We simply disable the
|
| /Documentation/filesystems/nfs/ |
| D | rpc-server-gss.txt | 40 kernel, but leave the initial context establishment to userspace. We
|
| /Documentation/filesystems/ |
| D | dlmfs.txt | 86 rmdir(2) signals dlmfs to leave the domain
|
| /Documentation/media/uapi/v4l/ |
| D | pixfmt-v4l2-mplane.rst | 46 If the client wants to leave this to the driver, then it should
|
| /Documentation/admin-guide/cgroup-v1/ |
| D | freezer-subsystem.rst | 85 the cgroup also leave the freezing state.
|
| /Documentation/scsi/ |
| D | 53c700.txt | 109 set to the PCI board device. Leave NULL for a non-pci board. This is
|
| /Documentation/media/uapi/cec/ |
| D | cec-ioc-adap-g-log-addrs.rst | 145 ``CEC_MSG_REPORT_FEATURES`` message. For CEC 1.4 you can either leave
153 RC Profile and the Device Features. For CEC 1.4 you can either leave
|
123456