Searched full:microseconds (Results 1 – 25 of 96) sorted by relevance
1234
| /Documentation/media/uapi/rc/ |
| D | lirc-get-rec-resolution.rst | 19 LIRC_GET_REC_RESOLUTION - Obtain the value of receive resolution, in microseconds.
24 .. c:function:: int ioctl( int fd, LIRC_GET_REC_RESOLUTION, __u32 *microseconds)
33 ``microseconds``
34 Resolution, in microseconds.
|
| D | lirc-dev-intro.rst | 113 Signifies the presence of IR in microseconds.
117 Signifies absence of IR in microseconds.
130 this packet will be sent, with the number of microseconds with
140 The values are alternating pulse and space lengths, in microseconds. The
|
| /Documentation/ABI/testing/ |
| D | sysfs-module | 21 microframe to be 80%, that is 100 microseconds out of 125
22 microseconds (full microframe).
26 microseconds of isochronous bandwidth per microframe to work
31 microseconds of periodic bandwidth per microframe.
|
| D | sysfs-class-rc-nuvoton | 8 All values are in microseconds.
|
| D | sysfs-class-led-flash | 26 Hardware timeout for flash, in microseconds. The flash strobe
36 Maximum flash timeout for this LED, in microseconds.
|
| /Documentation/devicetree/bindings/power/ |
| D | domain-idle-state.txt | 17 microseconds required to enter the idle state.
25 in microseconds required to exit the idle state.
31 in microseconds after which the idle state will yield
|
| /Documentation/devicetree/bindings/i2c/ |
| D | i2c-arb-gpio-challenge.txt | 34 microseconds).
50 - slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us.
51 - wait-retry-us: we'll attempt another claim after this many microseconds.
53 - wait-free-us: we'll give up after this many microseconds. Default is 50000 us.
|
| /Documentation/media/uapi/v4l/ |
| D | pixfmt-meta-d4xx.rst | 64 - Exposure time (in microseconds) used to capture the frame
98 - Time in microseconds from the beginning of a frame till its middle
100 - Time, used to read out a frame in microseconds
102 - Frame exposure time in microseconds
104 - In microseconds = 1000000 / framerate
106 - Time in microseconds from start of frame to data in USB buffer
|
| /Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 91 -maxim,shutdown-fps-time-period-us: u32, FPS time period in microseconds
95 -maxim,suspend-fps-time-period-us: u32, FPS time period in microseconds
111 Here supported time periods by device in microseconds are as follows:
112 MAX77620 supports 40, 80, 160, 320, 640, 1280, 2560 and 5120 microseconds.
113 MAX20024 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
114 MAX77663 supports 20, 40, 80, 160, 320, 640, 1280 and 2540 microseconds.
|
| /Documentation/devicetree/bindings/regulator/ |
| D | regulator.yaml | 59 description: The time taken, in microseconds, for the supply rail to
68 description: Settling time, in microseconds, for voltage change if regulator
73 description: Settling time, in microseconds, for voltage increase if
79 description: Settling time, in microseconds, for voltage decrease if
|
| D | tps65132-regulator.txt | 22 asserted for during active discharge, in microseconds.
|
| /Documentation/devicetree/bindings/input/ |
| D | qcom,pm8xxx-keypad.txt | 57 Definition: time in microseconds that key must be pressed or release
63 Definition: time in microseconds to pause between successive scans
|
| D | qcom,pm8xxx-pwrkey.txt | 28 Definition: time in microseconds that key must be pressed or release
|
| D | qcom,pm8941-pwrkey.txt | 27 Definition: time in microseconds that key must be pressed or released
|
| D | gpio-matrix-keypad.txt | 25 - col-scan-delay-us: delay, measured in microseconds, that is needed
|
| /Documentation/ABI/stable/ |
| D | sysfs-bus-w1 | 4 Description: Bus scanning interval, microseconds component.
|
| /Documentation/devicetree/bindings/iio/adc/ |
| D | at91_adc.txt | 13 - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
28 - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
|
| /Documentation/scheduler/ |
| D | sched-bwc.rst | 12 each given "period" (microseconds), a task group is allocated up to "quota"
13 microseconds of CPU time. That quota is assigned to per-cpu run queues in
28 cpu.cfs_quota_us: the total available run-time within a period (in microseconds)
29 cpu.cfs_period_us: the length of a period (in microseconds)
|
| /Documentation/devicetree/bindings/rng/ |
| D | timeriomem_rng.txt | 6 - period : wait time in microseconds to use between samples
|
| /Documentation/devicetree/bindings/spi/ |
| D | spi-controller.yaml | 121 Delay, in microseconds, after a read transfer.
133 Delay, in microseconds, after a write transfer.
|
| /Documentation/devicetree/bindings/pci/ |
| D | nvidia,tegra194-pcie.txt | 102 to be specified in microseconds
104 specified in microseconds
106 specified in microseconds
|
| /Documentation/devicetree/bindings/sound/ |
| D | ti,tas5086.txt | 14 - ti,charge-period: This property should contain the time in microseconds
|
| /Documentation/networking/ |
| D | ray_cs.txt | 73 beacon_period integer beacon period in Kilo-microseconds
91 hop_dwell integer hop dwell time in Kilo-microseconds
|
| /Documentation/devicetree/bindings/net/ |
| D | ethernet-phy.yaml | 148 Delay after the reset was asserted in microseconds. If this
153 Delay after the reset was deasserted in microseconds. If
|
| /Documentation/devicetree/bindings/watchdog/ |
| D | aspeed-wdt.txt | 41 - aspeed,ext-pulse-duration: External signal pulse duration in microseconds
|
1234