Searched +full:post +full:- (Results 1 – 25 of 96) sorted by relevance
1234
| /Documentation/livepatch/ |
| D | callbacks.rst | 5 Livepatch (un)patch-callbacks provide a mechanism for livepatch modules
10 - Safe updates to global data
12 - "Patches" to init and probe functions
14 - Patching otherwise unpatchable code (i.e. assembly)
25 - Module init/exit code doesn't run when disabling and re-enabling a
28 - A module notifier can't stop a to-be-patched module from loading.
39 * Pre-patch
40 - before a klp_object is patched
42 * Post-patch
43 - after a klp_object has been patched and is active
[all …]
|
| /Documentation/devicetree/bindings/clock/ |
| D | keystone-pll.txt | 1 Status: Unstable - ABI compatibility may be broken in the future
4 a divider and a post divider. The additional PLL IPs like ARMPLL, DDRPLL
11 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
14 - #clock-cells : from common clock binding; shall be set to 0.
15 - compatible : shall be "ti,keystone,main-pll-clock" or "ti,keystone,pll-clock"
16 - clocks : parent clock phandle
17 - reg - pll control0 and pll multipler registers
18 - reg-names : control, multiplier and post-divider. The multiplier and
19 post-divider registers are applicable only for main pll clock
20 - fixed-postdiv : fixed post divider value. If absent, use clkod register bits
[all …]
|
| D | st,stm32-rcc.txt | 6 Please refer to clock-bindings.txt for common clock controller binding usage.
10 - compatible: Should be:
11 "st,stm32f42xx-rcc"
12 "st,stm32f469-rcc"
13 "st,stm32f746-rcc"
14 "st,stm32f769-rcc"
16 - reg: should be register base and length as documented in the
18 - #reset-cells: 1, see below
19 - #clock-cells: 2, device nodes should specify the clock in their "clocks"
23 - clocks: External oscillator clock phandle
[all …]
|
| /Documentation/devicetree/bindings/input/ |
| D | hid-over-i2c.txt | 1 * HID over I2C Device-Tree bindings
8 http://msdn.microsoft.com/en-us/library/windows/hardware/hh852380.aspx
10 If this binding is used, the kernel module i2c-hid will handle the communication
14 - compatible: must be "hid-over-i2c"
15 - reg: i2c slave address
16 - hid-descr-addr: HID descriptor address
17 - interrupts: interrupt line
23 device-specific compatible properties, which should be used in addition to the
24 "hid-over-i2c" string.
26 - compatible:
[all …]
|
| /Documentation/devicetree/bindings/display/ |
| D | amlogic,meson-vpu.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 ---
5 $id: "http://devicetree.org/schemas/display/amlogic,meson-vpu.yaml#"
6 $schema: "http://devicetree.org/meta-schemas/core.yaml#"
11 - Neil Armstrong <narmstrong@baylibre.com>
17 DMC|---------------VPU (Video Processing Unit)----------------|------HHI------|
19 D |-------| |----| | | | | HDMI PLL |
20 D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK |
21 R |-------| |----| Processing | | | | |
22 | osd2 | | | |---| Enci ----------|----|-----VDAC------|
[all …]
|
| /Documentation/gpu/ |
| D | meson.rst | 5 .. kernel-doc:: drivers/gpu/drm/meson/meson_drv.c
16 DMC|---------------VPU (Video Processing Unit)----------------|------HHI------|
18 D |-------| |----| | | | | HDMI PLL |
19 D | vd2 | VIU | | Video Post | | Video Encoders |<---|-----VCLK |
20 R |-------| |----| Processing | | | | |
21 | osd2 | | | |---| Enci ----------|----|-----VDAC------|
22 R |-------| CSC |----| Scalers | | Encp ----------|----|----HDMI-TX----|
23 A | osd1 | | | Blenders | | Encl ----------|----|---------------|
24 M |-------|______|----|____________| |________________| | |
30 .. kernel-doc:: drivers/gpu/drm/meson/meson_viu.c
[all …]
|
| /Documentation/devicetree/bindings/ata/ |
| D | sata_highbank.txt | 3 SATA nodes are defined to describe on-chip Serial ATA controllers.
9 - compatible : compatible list, contains "calxeda,hb-ahci"
10 - interrupts : <interrupt mapping for SATA IRQ>
11 - reg : <registers mapping>
14 - dma-coherent : Present if dma operations are coherent
15 - calxeda,port-phys : phandle-combophy and lane assignment, which maps each
18 - calxeda,sgpio-gpio: phandle-gpio bank, bit offset, and default on or off,
21 - calxeda,led-order : a u32 array that map port numbers to offsets within the
23 - calxeda,tx-atten : a u32 array that contains TX attenuation override
26 - calxeda,pre-clocks : a u32 that indicates the number of additional clock
[all …]
|
| /Documentation/devicetree/bindings/net/ |
| D | fsl-fec.txt | 4 - compatible : Should be "fsl,<soc>-fec"
5 - reg : Address and length of the register set for the device
6 - interrupts : Should contain fec interrupt
7 - phy-mode : See ethernet.txt file in the same directory
10 - phy-supply : regulator that powers the Ethernet PHY.
11 - phy-handle : phandle to the PHY device connected to this device.
12 - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
13 Use instead of phy-handle.
14 - fsl,num-tx-queues : The property is valid for enet-avb IP, which supports
17 - fsl,num-rx-queues : The property is valid for enet-avb IP, which supports
[all …]
|
| D | hisilicon-femac.txt | 4 - compatible: should contain one of the following version strings:
5 * "hisilicon,hisi-femac-v1"
6 * "hisilicon,hisi-femac-v2"
7 and the soc string "hisilicon,hi3516cv300-femac".
8 - reg: specifies base physical address(s) and size of the device registers.
11 - interrupts: should contain the MAC interrupt.
12 - clocks: A phandle to the MAC main clock.
13 - resets: should contain the phandle to the MAC reset signal(required) and
15 - reset-names: should contain the reset signal name "mac"(required)
17 - phy-mode: see ethernet.txt [1].
[all …]
|
| /Documentation/ABI/testing/ |
| D | sysfs-class-fpga-manager | 35 * write complete = Doing post programming steps
36 * write complete error = Error while doing post programming
50 * reconfig operation error - invalid operations detected by
54 * reconfig CRC error - CRC error detected by
56 * reconfig incompatible image - reconfiguration image is
58 * reconfig IP protocol error - protocol errors detected by
60 * reconfig fifo overflow error - FIFO overflow detected by
|
| /Documentation/devicetree/bindings/leds/backlight/ |
| D | pwm-backlight.txt | 1 pwm-backlight bindings
4 - compatible: "pwm-backlight"
5 - pwms: OF device-tree PWM specification (see PWM binding[0])
6 - power-supply: regulator for supply voltage
9 - pwm-names: a list of names for the PWM devices specified in the
11 - enable-gpios: contains a single GPIO specifier for the GPIO which enables
13 - post-pwm-on-delay-ms: Delay in ms between setting an initial (non-zero) PWM
15 - pwm-off-delay-ms: Delay in ms between disabling the backlight using GPIO
17 - brightness-levels: Array of distinct brightness levels. Typically these
23 - default-brightness-level: The default brightness level (index into the
[all …]
|
| /Documentation/media/uapi/dvb/ |
| D | frontend-stat-properties.rst | 4 .. Foundation, with no Invariant Sections, no Front-Cover Texts
5 .. and no Back-Cover Texts. A copy of the license is included at
6 .. Documentation/media/uapi/fdl-appendix.rst.
8 .. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections
10 .. _frontend-stat-properties:
39 - ``svalue`` or ``uvalue``, where ``svalue`` is for signed values of
43 - ``scale`` - Scale for the value. It can be:
45 - ``FE_SCALE_NOT_AVAILABLE`` - The parameter is supported by the
49 - ``FE_SCALE_DECIBEL`` - parameter is a signed value, measured in
52 - ``FE_SCALE_RELATIVE`` - parameter is a unsigned value, where 0
[all …]
|
| /Documentation/networking/ |
| D | ax25.txt | 4 found on http://www.linux-ax25.org.
7 called linux-hams@vger.kernel.org. To subscribe to it, send a message to
8 majordomo@vger.kernel.org with the words "subscribe linux-hams" in the body
10 subscribed to post but of course that means you might miss an answer.
|
| D | bridge.rst | 1 .. SPDX-License-Identifier: GPL-2.0
13 The bridge-utilities are maintained at:
14 git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/bridge-utils.git
19 If you still have questions, don't hesitate to post to the mailing list
20 (more info https://lists.linux-foundation.org/mailman/listinfo/bridge).
|
| D | tc-actions-env-rules.txt | 14 3) Dropping packets you don't own is a no-no. You simply return
23 Post on netdev if something is unclear.
|
| /Documentation/sound/soc/ |
| D | machine.rst | 12 the following struct:-
24 /* the pre and post PM functions are used to do any PM work before and
33 /* CPU <--> Codec DAI links */
41 ----------------
46 ------------------
47 The machine driver has pre and post versions of suspend and resume to take care
53 -------------------------
62 /* corgi digital audio interface glue - connects codec <--> CPU */
66 .cpu_dai_name = "pxa-is2-dai",
67 .codec_dai_name = "wm8731-hifi",
[all …]
|
| /Documentation/filesystems/ |
| D | efivarfs.txt | 2 efivarfs - a (U)EFI variable filesystem
16 mount -t efivarfs none /sys/firmware/efi/efivars
18 Due to the presence of numerous firmware bugs where removing non-standard
19 UEFI variables causes the system firmware to fail to POST, efivarfs
20 files that are not well-known standardized variables are created
21 as immutable files. This doesn't prevent removal - "chattr -i" will work -
|
| /Documentation/devicetree/bindings/phy/ |
| D | apm-xgene-phy.txt | 1 * APM X-Gene 15Gbps Multi-purpose PHY nodes
3 PHY nodes are defined to describe on-chip 15Gbps Multi-purpose PHY. Each
7 - compatible : Shall be "apm,xgene-phy".
8 - reg : PHY memory resource is the SDS PHY access resource.
9 - #phy-cells : Shall be 1 as it expects one argument for setting
14 - status : Shall be "ok" if enabled or "disabled" if disabled.
16 - clocks : Reference to the clock entry.
17 - apm,tx-eye-tuning : Manual control to fine tune the capture of the serial
19 Two set of 3-tuple setting for each (up to 3)
22 - apm,tx-eye-direction : Eye tuning manual control direction. 0 means sample
[all …]
|
| /Documentation/media/v4l-drivers/ |
| D | cx18.rst | 1 .. SPDX-License-Identifier: GPL-2.0
15 - Hauppauge HVR-1600
16 - Compro VideoMate H900
17 - Yuan MPC718
18 - Conexant Raptor PAL/SECAM devkit
23 then post to the video4linux or ivtv-users mailing list.
37 http://dl.ivtvdriver.org/ivtv/firmware/cx18-firmware.tar.gz
|
| /Documentation/trace/ |
| D | events-msr.rst | 17 - msr: MSR number
18 - val: Value written
19 - failed: 1 if the access failed, otherwise 0
26 - msr: MSR number
27 - val: Value written
28 - failed: 1 if the access failed, otherwise 0
35 The trace data can be post processed with the postprocess/decode_msr.py script::
37 cat /sys/kernel/debug/tracing/trace | decode_msr.py /usr/src/linux/include/asm/msr-index.h
|
| /Documentation/devicetree/bindings/mmc/ |
| D | mmc-pwrseq-simple.txt | 8 - compatible : contains "mmc-pwrseq-simple".
11 - reset-gpios : contains a list of GPIO specifiers. The reset GPIOs are asserted
13 They will be de-asserted right after the power has been provided to the
15 - clocks : Must contain an entry for the entry in clock-names.
16 See ../clocks/clock-bindings.txt for details.
17 - clock-names : Must include the following entry:
19 - post-power-on-delay-ms : Delay in ms after powering the card and
20 de-asserting the reset-gpios (if any)
21 - power-off-delay-us : Delay in us after asserting the reset-gpios (if any)
27 compatible = "mmc-pwrseq-simple";
[all …]
|
| /Documentation/hwmon/ |
| D | ds620.rst | 20 -----------
24 into non-volatile on-chip registers). Temperature range is -55 degree Celsius
26 returned via sysfs displays post decimal positions.
38 The PO output pin of the DS620 operates active-low.
|
| /Documentation/devicetree/bindings/mailbox/ |
| D | stm32-ipcc.txt | 1 * STMicroelectronics STM32 IPCC (Inter-Processor Communication Controller)
3 The IPCC block provides a non blocking signaling mechanism to post and
9 - compatible: Must be "st,stm32mp1-ipcc"
10 - reg: Register address range (base address and length)
11 - st,proc-id: Processor id using the mailbox (0 or 1)
12 - clocks: Input clock
13 - interrupt-names: List of names for the interrupts described by the interrupt
15 - "rx"
16 - "tx"
17 - "wakeup"
[all …]
|
| /Documentation/accounting/ |
| D | cgroupstats.rst | 9 Per cgroup statistics infrastructure re-uses code from the taskstats
15 The current model for cgroupstats is a pull, a push model (to post
28 ~/balbir/cgroupstats # ./getdelays -C "/sys/fs/cgroup/a"
30 ~/balbir/cgroupstats # ./getdelays -C "/sys/fs/cgroup"
|
| /Documentation/cpu-freq/ |
| D | index.txt | 20 ----------------------------
22 amd-powernow.txt - AMD powernow driver specific file.
24 core.txt - General description of the CPUFreq core and
27 cpu-drivers.txt - How to implement a new cpufreq processor driver.
29 cpufreq-nforce2.txt - nVidia nForce2 platform specific file.
31 cpufreq-stats.txt - General description of sysfs cpufreq stats.
33 index.txt - File index, Mailing list and Links (this document)
35 pcc-cpufreq.txt - PCC cpufreq driver specific file.
39 ------------
41 you can report bugs, problems or submit patches. To post a message,
[all …]
|
1234