Searched full:references (Results 1 – 25 of 235) sorted by relevance
12345678910
| /Documentation/doc-guide/ |
| D | parse-headers.rst | 6 order to describe the userspace API and to generate cross-references
7 between the code and the documentation. Adding cross-references for
12 cross-references. It has to be called via Makefile, while building the
26 enums and defines and create cross-references to a Sphinx book.
65 included via ..parsed-literal block with cross-references for the
73 enums and enum symbols and create cross-references for all of them.
84 The \ **ignore**\ means that it won't generate cross references for a
92 The \ **replace**\ means that it will generate cross references for a
140 references for \ **typedef**\ , \ **enum**\ and \ **struct**\ types. It will use :ref:
162 It won't generate cross-references for \ **PRIVATE**\ .
|
| /Documentation/gpu/dp-mst/ |
| D | topology-figure-2.dot | 9 /* Driver malloc references */
24 /* Topology references */
32 /* Malloc references */
|
| D | topology-figure-1.dot | 9 /* Driver malloc references */
24 /* Topology references */
30 /* Malloc references */
|
| D | topology-figure-3.dot | 12 /* Driver malloc references */
26 /* Topology references */
34 /* Malloc references */
|
| /Documentation/devicetree/ |
| D | dynamic-resolution-notes.txt | 18 3. Using the __local__fixups__ node information adjust all local references
20 4. For each property in the __fixups__ node locate the node it references
|
| /Documentation/firmware-guide/acpi/dsd/ |
| D | leds.rst | 18 references are limited to device nodes only [2]. For this reason using the same
37 show below. Objects not relevant for LEDs or the references to them have been
90 References chapter
111 [7] Documentation/firmware-guide/acpi/dsd/data-node-references.rst
|
| D | graph.rst | 16 hierarchical data extension supports nodes with references to other
68 name followed by a reference in the same package. Such references consist of
71 data extension reference under the port. Individual references thus appear as::
78 The references to endpoints must be always done both ways, to the
153 References chapter
|
| D | data-node-references.rst | 13 document defines a scheme to implement such references.
84 References chapter
|
| /Documentation/devicetree/bindings/display/bridge/ |
| D | dw_mipi_dsi.txt | 16 - clocks: References to all the clocks specified in the clock-names property
23 - resets: References to all the resets specified in the reset-names property
|
| /Documentation/sphinx/ |
| D | automarkup.py | 25 # to the creation of incorrect and confusing cross references. So
34 # appropriate cross references.
89 # avoid adding cross-references to functions that have been explicitly
|
| /Documentation/vm/ |
| D | page_frags.rst | 40 was implemented. It allows for freeing multiple references from a single
42 cleaning up the multiple references that were added to a page in order to
|
| /Documentation/devicetree/bindings/phy/ |
| D | phy-lantiq-rcu-usb2.txt | 22 - clocks : References to the (PMU) "phy" clk gate.
24 - resets : References to the RCU USB configuration reset bits.
|
| D | phy-ath79-usb.txt | 7 - resets: references to the reset controllers
|
| /Documentation/firmware-guide/acpi/ |
| D | index.rst | 12 dsd/data-node-references
|
| /Documentation/livepatch/ |
| D | shadow-vars.rst | 26 A hashtable references all shadow variables. These references are
86 - find and remove any <*, id> references from global hashtable
214 3. References
|
| /Documentation/devicetree/bindings/siox/ |
| D | eckelmann,siox-gpio.txt | 5 - din-gpios, dout-gpios, dclk-gpios, dld-gpios: references gpios for the
|
| /Documentation/driver-api/80211/ |
| D | introduction.rst | 17 References to this standard will be given as "802.11-2007 8.1.5".
|
| /Documentation/devicetree/bindings/clock/ |
| D | gpio-mux-clock.txt | 9 - clocks: list of two references to parent clocks.
|
| /Documentation/misc-devices/ |
| D | c2port.txt | 28 References
31 The C2 Interface main references are at (http://www.silabs.com)
|
| /Documentation/openrisc/ |
| D | todo.rst | 12 - Finish the renaming cleanup... there are references to or32 in the code
|
| /Documentation/usb/ |
| D | usb-help.rst | 2 USB references
|
| /Documentation/ide/ |
| D | warm-plug-howto.rst | 16 no other active references to devices before doing "delete_devices" step,
|
| /Documentation/devicetree/bindings/arm/ |
| D | scu.txt | 7 References:
|
| /Documentation/devicetree/bindings/rtc/ |
| D | faraday,ftrtc010.txt | 12 - clocks: when present should contain clock references to the
|
| /Documentation/devicetree/bindings/interrupt-controller/ |
| D | st,stm32-exti.txt | 13 - interrupts: interrupts references to primary interrupt controller
|
12345678910