Home
last modified time | relevance | path

Searched +full:regulator +full:- +full:initial +full:- +full:mode (Results 1 – 13 of 13) sorted by relevance

/Documentation/devicetree/bindings/regulator/
Dmcp16502-regulator.txt4 - compatible: "microchip,mcp16502"
5 - reg: I2C slave address
6 - lpm-gpios: GPIO for LPM pin. Note that this GPIO *must* remain high during
7 suspend-to-ram, keeping the PMIC into HIBERNATE mode.
8 - regulators: A node that houses a sub-node for each regulator within
9 the device. Each sub-node is identified using the node's
10 name. The content of each sub-node is defined by the
11 standard binding for regulators; see regulator.txt.
14 1) VDD_IO - Buck (1.2 - 3.7 V)
15 2) VDD_DDR - Buck (0.6 - 1.85 V)
[all …]
Dact8945a-regulator.txt1 Device-Tree bindings for regulators of Active-semi ACT8945A Multi-Function Device
4 - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt.
7 - active-semi,vsel-high: Indicates if the VSEL pin is set to logic-high.
8 If this property is missing, assume the VSEL pin is set to logic-low.
11 - vp1-supply: The input supply for REG_DCDC1
12 - vp2-supply: The input supply for REG_DCDC2
13 - vp3-supply: The input supply for REG_DCDC3
14 - inl45-supply: The input supply for REG_LDO1 and REG_LDO2
15 - inl67-supply: The input supply for REG_LDO3 and REG_LDO4
17 Any standard regulator properties can be used to configure the single regulator.
[all …]
Dmax77802.txt3 This is a part of device tree bindings of MAX77802 multi-function device.
6 The MAX77802 PMIC has 10 high-efficiency Buck and 32 Low-dropout (LDO)
12 - inb1-supply: The input supply for BUCK1
13 - inb2-supply: The input supply for BUCK2
14 - inb3-supply: The input supply for BUCK3
15 - inb4-supply: The input supply for BUCK4
16 - inb5-supply: The input supply for BUCK5
17 - inb6-supply: The input supply for BUCK6
18 - inb7-supply: The input supply for BUCK7
19 - inb8-supply: The input supply for BUCK8
[all …]
Dact8865-regulator.txt2 -------------------
5 - compatible: "active-semi,act8846" or "active-semi,act8865" or "active-semi,act8600"
6 - reg: I2C slave address
9 - system-power-controller: Telling whether or not this pmic is controlling
10 the system power. See Documentation/devicetree/bindings/power/power-controller.txt .
11 - active-semi,vsel-high: Indicates the VSEL pin is high.
15 - for act8600:
16 - vp1-supply: The input supply for DCDC_REG1
17 - vp2-supply: The input supply for DCDC_REG2
18 - vp3-supply: The input supply for DCDC_REG3
[all …]
Dqcom,rpmh-regulator.txt3 rpmh-regulator devices support PMIC regulator management via the Voltage
4 Regulator Manager (VRM) and Oscillator Buffer (XOB) RPMh accelerators. The APPS
7 parameters for a given regulator: enable state, output voltage, and operating
8 mode. The XOB allows changing only a single parameter for a given regulator:
10 enable state of any PMIC peripheral. It is used for clock buffers, low-voltage
11 switches, and LDO/SMPS regulators which have a fixed voltage and mode.
19 RPMh device node. The second level describes each regulator within the PMIC
23 The names used for regulator nodes must match those supported by a given PMIC.
24 Supported regulator node names:
25 PM8005: smps1 - smps4
[all …]
Dqcom,spmi-regulator.txt3 - compatible:
7 "qcom,pm8005-regulators"
8 "qcom,pm8841-regulators"
9 "qcom,pm8916-regulators"
10 "qcom,pm8941-regulators"
11 "qcom,pm8994-regulators"
12 "qcom,pmi8994-regulators"
13 "qcom,pms405-regulators"
15 - interrupts:
17 Value type: <prop-encoded-array>
[all …]
Dregulator.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/regulator/regulator.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Liam Girdwood <lgirdwood@gmail.com>
11 - Mark Brown <broonie@kernel.org>
14 regulator-name:
15 description: A string used as a descriptive name for regulator outputs
18 regulator-min-microvolt:
21 regulator-max-microvolt:
[all …]
Dtwl-regulator.txt5 - compatible:
6 - "ti,twl6030-vaux1" for VAUX1 LDO
7 - "ti,twl6030-vaux2" for VAUX2 LDO
8 - "ti,twl6030-vaux3" for VAUX3 LDO
9 - "ti,twl6030-vmmc" for VMMC LDO
10 - "ti,twl6030-vpp" for VPP LDO
11 - "ti,twl6030-vusim" for VUSIM LDO
12 - "ti,twl6030-vana" for VANA LDO
13 - "ti,twl6030-vcxio" for VCXIO LDO
14 - "ti,twl6030-vdac" for VDAC LDO
[all …]
Dlp872x.txt4 - compatible: "ti,lp8720" or "ti,lp8725"
5 - reg: I2C slave address. 0x7d = LP8720, 0x7a = LP8725
8 - ti,general-config: the value of LP872X_GENERAL_CFG register (u8)
22 bit[1]: LDO sleep control. 1 = sleep mode, 0 = normal
27 - ti,update-config: define it when LP872X_GENERAL_CFG register should be set
28 - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices.
29 - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2.
30 - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH.
31 - enable-gpios: GPIO specifier for EN pin control of LP872x devices.
37 (Documentation/devicetree/bindings/regulator/regulator.txt)
[all …]
/Documentation/devicetree/bindings/sound/
Dcs35l36.txt5 - compatible : "cirrus,cs35l36"
7 - reg : the I2C address of the device for I2C
9 - VA-supply, VP-supply : power supplies for the device,
11 Documentation/devicetree/bindings/regulator/regulator.txt.
13 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
18 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
24 - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
25 Seeds the digital boost converter's inductor estimation block with the initial
32 - cirrus,multi-amp-mode : Boolean to determine if there are more than
33 one amplifier in the system. If more than one it is best to Hi-Z the ASP
[all …]
/Documentation/devicetree/bindings/leds/backlight/
Dlp855x.txt4 - compatible: "ti,lp8550", "ti,lp8551", "ti,lp8552", "ti,lp8553",
6 - reg: I2C slave address (u8)
7 - dev-ctrl: Value of DEVICE CONTROL register (u8). It depends on the device.
10 - bl-name: Backlight device name (string)
11 - init-brt: Initial value of backlight brightness (u8)
12 - pwm-period: PWM period value. Set only PWM input mode used (u32)
13 - rom-addr: Register address of ROM area to be updated (u8)
14 - rom-val: Register value to be updated (u8)
15 - power-supply: Regulator which controls the 3V rail
16 - enable-supply: Regulator which controls the EN/VDDIO input
[all …]
/Documentation/devicetree/bindings/net/
Dmediatek-bluetooth.txt1 MediaTek SoC built-in Bluetooth Devices
5 child node of the serial node with BTIF. The dt-bindings details for BTIF
10 - compatible: Must be
11 "mediatek,mt7622-bluetooth": for MT7622 SoC
12 - clocks: Should be the clock specifiers corresponding to the entry in
13 clock-names property.
14 - clock-names: Should contain "ref" entries.
15 - power-domains: Phandle to the power domain that the device is part of
20 compatible = "mediatek,mt7622-btif",
21 "mediatek,mtk-btif";
[all …]
/Documentation/admin-guide/laptops/
Dthinkpad-acpi.rst9 - Borislav Deianov <borislav@users.sf.net>
10 - Henrique de Moraes Holschuh <hmh@hmh.eng.br>
12 http://ibm-acpi.sf.net/
19 This driver used to be named ibm-acpi until kernel 2.6.21 and release
20 0.13-20070314. It used to be in the drivers/acpi tree, but it was
21 moved to the drivers/misc tree and renamed to thinkpad-acpi for kernel
25 The driver is named "thinkpad-acpi". In some places, like module
29 "tpacpi" is used as a shorthand where "thinkpad-acpi" would be too
33 ------
38 - Fn key combinations
[all …]