Searched +full:regulator +full:- +full:min +full:- +full:microamp (Results 1 – 16 of 16) sorted by relevance
| /Documentation/devicetree/bindings/regulator/ |
| D | da9211.txt | 2 Voltage Regulator
5 - compatible: "dlg,da9211" or "dlg,da9212" or "dlg,da9213" or "dlg,da9223"
7 - reg: I2C slave address, usually 0x68.
8 - interrupts: the interrupt outputs of the controller
9 - regulators: A node that houses a sub-node for each regulator within the
10 device. Each sub-node is identified using the node's name, with valid
11 values listed below. The content of each sub-node is defined by the
12 standard binding for regulators; see regulator.txt.
16 - enable-gpios: platform gpio for control of BUCKA/BUCKB.
17 - Any optional property defined in regulator.txt
[all …]
|
| D | pv88090.txt | 1 * Powerventure Semiconductor PV88090 Voltage Regulator
4 - compatible: "pvs,pv88090".
5 - reg: I2C slave address, usually 0x48.
6 - interrupts: the interrupt outputs of the controller
7 - regulators: A node that houses a sub-node for each regulator within the
8 device. Each sub-node is identified using the node's name, with valid
9 values listed below. The content of each sub-node is defined by the
10 standard binding for regulators; see regulator.txt.
14 - Any optional property defined in regulator.txt
21 interrupt-parent = <&gpio>;
[all …]
|
| D | pv88080.txt | 1 * Powerventure Semiconductor PV88080 Voltage Regulator
4 - compatible: Must be one of the following, depending on the
6 - "pvs,pv88080" (DEPRECATED)
8 - "pvs,pv88080-aa" for PV88080 AA or AB silicon
9 - "pvs,pv88080-ba" for PV88080 BA or BB silicon
11 - reg: I2C slave address, usually 0x49
12 - interrupts: the interrupt outputs of the controller
13 - regulators: A node that houses a sub-node for each regulator within the
14 device. Each sub-node is identified using the node's name, with valid
15 values listed below. The content of each sub-node is defined by the
[all …]
|
| D | tps65218.txt | 4 - compatible: "ti,tps65218"
5 - reg: I2C slave address
7 - List of regulators provided by this controller, must be named
8 after their hardware counterparts: dcdc[1-6] and ldo1
9 - This is the list of child nodes that specify the regulator
12 using the standard binding for regulators found at ./regulator.txt.
15 tps65217: regulator-dcdc1, regulator-dcdc2, regulator-dcdc3, regulator-dcdc4,
16 regulator-dcdc5, regulator-dcdc6, regulator-ldo1, regulator-ls3.
17 Each regulator is defined using the standard binding for regulators.
24 interrupt-controller;
[all …]
|
| D | lp872x.txt | 4 - compatible: "ti,lp8720" or "ti,lp8725"
5 - reg: I2C slave address. 0x7d = LP8720, 0x7a = LP8725
8 - ti,general-config: the value of LP872X_GENERAL_CFG register (u8)
27 - ti,update-config: define it when LP872X_GENERAL_CFG register should be set
28 - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices.
29 - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2.
30 - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH.
31 - enable-gpios: GPIO specifier for EN pin control of LP872x devices.
37 (Documentation/devicetree/bindings/regulator/regulator.txt)
40 - LP8720: http://www.ti.com/lit/ds/symlink/lp8720.pdf
[all …]
|
| D | da9210.txt | 1 * Dialog Semiconductor DA9210 Multi-phase 12A DCDC BUCK Converter
5 - compatible: must be "dlg,da9210"
6 - reg: the i2c slave address of the regulator. It should be 0x68.
10 - interrupts: a reference to the DA9210 interrupt, if available.
12 Any standard regulator properties can be used to configure the single da9210
21 interrupt-parent = <...>;
24 regulator-min-microvolt = <300000>;
25 regulator-max-microvolt = <1570000>;
26 regulator-min-microamp = <1600000>;
27 regulator-max-microamp = <4600000>;
[all …]
|
| D | pv88060.txt | 1 * Powerventure Semiconductor PV88060 Voltage Regulator
4 - compatible: "pvs,pv88060".
5 - reg: I2C slave address, usually 0x49.
6 - interrupts: the interrupt outputs of the controller
7 - regulators: A node that houses a sub-node for each regulator within the
8 device. Each sub-node is identified using the node's name, with valid
9 values listed below. The content of each sub-node is defined by the
10 standard binding for regulators; see regulator.txt.
15 - Any optional property defined in regulator.txt
22 interrupt-parent = <&gpio>;
[all …]
|
| D | regulator.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/regulator/regulator.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Liam Girdwood <lgirdwood@gmail.com>
11 - Mark Brown <broonie@kernel.org>
14 regulator-name:
15 description: A string used as a descriptive name for regulator outputs
18 regulator-min-microvolt:
21 regulator-max-microvolt:
[all …]
|
| /Documentation/devicetree/bindings/mfd/ |
| D | lp873x.txt | 4 - compatible: "ti,lp8732", "ti,lp8733"
5 - reg: I2C slave address.
6 - gpio-controller: Marks the device node as a GPIO Controller.
7 - #gpio-cells: Should be two. The first cell is the pin number and
10 - xxx-in-supply: Phandle to parent supply node of each regulator
13 - regulators: List of child nodes that specify the regulator
20 gpio-controller;
21 #gpio-cells = <2>;
23 buck0-in-supply = <&vsys_3v3>;
24 buck1-in-supply = <&vsys_3v3>;
[all …]
|
| D | max14577.txt | 1 Maxim MAX14577/77836 Multi-Function Device
3 MAX14577 is a Multi-Function Device with Micro-USB Interface Circuit, Li+
11 - compatible : Must be "maxim,max14577" or "maxim,max77836".
12 - reg : I2C slave address for the max14577 chip (0x25 for max14577/max77836)
13 - interrupts : IRQ line for the chip.
17 - charger :
20 - compatible : "maxim,max14577-charger"
21 or "maxim,max77836-charger"
22 - maxim,fast-charge-uamp : Current in uA for Fast Charge;
24 - for max14577: 90000 - 950000;
[all …]
|
| D | max77693.txt | 1 Maxim MAX77693 multi-function device
4 - PMIC,
5 - CHARGER,
6 - LED,
7 - MUIC,
8 - HAPTIC
14 - compatible : Must be "maxim,max77693".
15 - reg : Specifies the i2c slave address of PMIC block.
16 - interrupts : This i2c device has an IRQ line connected to the main SoC.
19 - regulators : The regulators of max77693 have to be instantiated under subnode
[all …]
|
| D | da9062.txt | 4 - http://www.dialog-semiconductor.com/products/da9062
5 - http://www.dialog-semiconductor.com/products/da9061
10 ------ ------------ -----------
11 da9062-regulator : : LDOs & BUCKs
12 da9062-rtc : : Real-Time Clock
13 da9062-onkey : : On Key
14 da9062-watchdog : : Watchdog Timer
15 da9062-thermal : : Thermal
20 ------ ------------ -----------
21 da9062-regulator : : LDOs & BUCKs
[all …]
|
| D | da9063.txt | 3 DA9093 consists of a large and varied group of sub-devices (I2C Only):
6 ------ ------------ -----------
7 da9063-regulator : : LDOs & BUCKs
8 da9063-onkey : : On Key
9 da9063-rtc : : Real-Time Clock (DA9063 only)
10 da9063-watchdog : : Watchdog
16 - compatible : Should be "dlg,da9063" or "dlg,da9063l"
17 - reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
19 - interrupts : IRQ line information.
20 - interrupt-controller
[all …]
|
| D | ti-lmu.txt | 6 ------ ---------------------------------
7 LM3631 Backlight and regulator
8 LM3632 Backlight and regulator
11 LM36274 Backlight and regulator
14 - compatible: Should be one of:
20 - reg: I2C slave address.
28 - enable-gpios: A GPIO specifier for hardware enable pin.
29 - ramp-up-us: Current ramping from one brightness level to
31 Range from 2048 us - 117.44 s
32 - ramp-down-us: Current ramping from one brightness level to
[all …]
|
| /Documentation/devicetree/bindings/ufs/ |
| D | ufshcd-pltfrm.txt | 3 UFSHC nodes are defined to describe on-chip UFS host controllers.
7 - compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0"
10 SoC-specific compatible along with "qcom,ufshc" and
12 "qcom,msm8994-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
13 "qcom,msm8996-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
14 "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
15 "qcom,sdm845-ufshc", "qcom,ufshc", "jedec,ufs-2.0"
16 - interrupts : <interrupt mapping for UFS host controller IRQ>
17 - reg : <registers mapping>
20 - phys : phandle to UFS PHY node
[all …]
|
| /Documentation/devicetree/bindings/opp/ |
| D | opp.txt | 2 ----------------------------------------------------
4 Devices work at voltage-current-frequency combinations and some implementations
13 Binding 1: operating-points
16 This binding only supports voltage-frequency pairs.
19 - operating-points: An array of 2-tuples items, and each item consists
20 of frequency and voltage like <freq-kHz vol-uV>.
27 compatible = "arm,cortex-a9";
29 next-level-cache = <&L2>;
30 operating-points = <
39 Binding 2: operating-points-v2
[all …]
|