Searched full:returned (Results 1 – 25 of 548) sorted by relevance
12345678910>>...22
| /Documentation/i2c/ |
| D | fault-codes.rst | 28 These are returned as negative numbers from most calls, with zero or
34 codes that may be returned, and other cases where these codes should
35 be returned. However, drivers should not return other codes for these
38 Also, codes returned by adapter probe methods follow rules which are
43 Returned by I2C adapters when they lose arbitration in master
47 Also returned when trying to invoke an I2C operation in an
52 Returned by SMBus logic when an invalid Packet Error Code byte
61 Returned by SMBus adapters when the bus was busy for longer
77 Returned by driver probe() methods. This is a bit more
85 Returned by any component that can't allocate memory when
[all …]
|
| /Documentation/media/uapi/rc/ |
| D | lirc-write.rst | 37 File descriptor returned by ``open()``.
66 ``EINVAL`` is returned. Set the desired scancode in the ``scancode`` member,
69 set to 0, else ``EINVAL`` is returned. If there is no protocol encoder
71 ``EINVAL`` is returned. The write function blocks until the scancode
78 On success, the number of bytes written is returned. It is not an error if
80 of data required for one frame. On error, -1 is returned, and the ``errno``
|
| /Documentation/filesystems/ |
| D | fiemap.txt | 30 which the process would like mappings for. Extents returned mirror
31 those on disk - that is, the logical offset of the 1st returned extent
32 may start before fm_start, and the range covered by the last returned
47 fm_extents[] array is ignored (no extents will be returned), and the
58 If this flag is set, the extents returned will describe the inodes
65 Extent information is returned within the embedded fm_extents array
69 returned via fm_mapped_extents. If the number of fiemap_extents
72 array will be returned and fm_mapped_extents will be equal to
78 returned in fm_extents.
94 returned, fe_logical, fe_physical, and fe_length will be aligned to the
[all …]
|
| /Documentation/bpf/ |
| D | prog_cgroup_sockopt.rst | 26 If BPF program sets ``optlen`` to -1, the control will be returned
37 * ``0`` - reject the syscall, ``EPERM`` will be returned to the userspace.
45 if it's interested in whatever kernel has returned. BPF hook can override
48 buffer is too small), ``EFAULT`` is returned.
53 original value that the kernel returned. Any other value will trigger
59 * ``0`` - reject the syscall, ``EPERM`` will be returned to the userspace.
|
| /Documentation/media/uapi/mediactl/ |
| D | media-request-ioc-queue.rst | 50 File descriptor returned by :ref:`MEDIA_IOC_REQUEST_ALLOC`.
62 If the request was already queued before, then ``EBUSY`` is returned.
63 Other errors can be returned if the contents of the request contained
73 (without a request). ``EBUSY`` will be returned if the first buffer was
82 On success 0 is returned, on error -1 and the ``errno`` variable is set
92 to have at least one buffer. This can also be returned if some required
|
| /Documentation/media/uapi/dvb/ |
| D | dmx-get-stc.rst | 32 File descriptor returned by :c:func:`open() <dvb-dmx-open>`.
45 The result is returned in form of a ratio with a 64 bit numerator
53 On success 0 is returned.
55 On error -1 is returned, and the ``errno`` variable is set
|
| D | dmx-add-pid.rst | 33 File descriptor returned by :c:func:`open() <dvb-dmx-open>`.
50 On success 0 is returned.
52 On error -1 is returned, and the ``errno`` variable is set
|
| D | ca-set-descr.rst | 33 File descriptor returned by a previous call to :c:func:`open() <cec-open>`.
47 On success 0 is returned.
49 On error -1 is returned, and the ``errno`` variable is set
|
| D | ca-get-cap.rst | 33 File descriptor returned by a previous call to :c:func:`open() <dvb-ca-open>`.
47 On success 0 is returned and :c:type:`ca_caps` is filled.
49 On error, -1 is returned and the ``errno`` variable is set
|
| D | dmx-stop.rst | 33 File descriptor returned by :c:func:`open() <dvb-dmx-open>`.
46 On success 0 is returned.
48 On error -1 is returned, and the ``errno`` variable is set
|
| D | ca-reset.rst | 33 File descriptor returned by a previous call to :c:func:`open() <cec-open>`.
45 On success 0 is returned.
47 On error -1 is returned, and the ``errno`` variable is set
|
| D | fe-read-snr.rst | 34 File descriptor returned by :c:func:`open() <dvb-fe-open>`.
51 On success 0 is returned.
53 On error -1 is returned, and the ``errno`` variable is set
|
| D | ca-get-descr-info.rst | 32 File descriptor returned by a previous call to :c:func:`open() <dvb-ca-open>`.
45 On success 0 is returned, and :c:type:`ca_descr_info` is filled.
47 On error -1 is returned, and the ``errno`` variable is set
|
| D | ca-fclose.rst | 33 File descriptor returned by a previous call to :c:func:`open() <dvb-ca-open>`.
44 On success 0 is returned.
46 On error -1 is returned, and the ``errno`` variable is set
|
| D | fe-diseqc-send-master-cmd.rst | 33 File descriptor returned by :ref:`open() <frontend_f_open>`.
49 On success 0 is returned.
51 On error -1 is returned, and the ``errno`` variable is set
|
| D | dmx-remove-pid.rst | 33 File descriptor returned by :c:func:`open() <dvb-dmx-open>`.
51 On success 0 is returned.
53 On error -1 is returned, and the ``errno`` variable is set
|
| D | net-remove-if.rst | 33 File descriptor returned by :ref:`open() <frontend_f_open>`.
49 On success 0 is returned, and :c:type:`ca_slot_info` is filled.
51 On error -1 is returned, and the ``errno`` variable is set
|
| D | dmx-set-buffer-size.rst | 33 File descriptor returned by :c:func:`open() <dvb-dmx-open>`.
51 On success 0 is returned.
53 On error -1 is returned, and the ``errno`` variable is set
|
| D | dmx-fclose.rst | 33 File descriptor returned by a previous call to
46 On success 0 is returned.
48 On error, -1 is returned and the ``errno`` variable is set
|
| D | ca-send-msg.rst | 33 File descriptor returned by a previous call to :c:func:`open() <cec-open>`.
52 On success 0 is returned.
54 On error -1 is returned, and the ``errno`` variable is set
|
| D | ca-get-msg.rst | 33 File descriptor returned by a previous call to :c:func:`open() <dvb-ca-open>`.
53 On success 0 is returned.
55 On error -1 is returned, and the ``errno`` variable is set
|
| /Documentation/admin-guide/device-mapper/ |
| D | statistics.rst | 108 region_id returned from @stats_create
114 region_id returned from @stats_create
122 are returned.
123 If it is not specified, all regions are returned.
136 region_id returned from @stats_create
140 If omitted, all lines are returned.
144 If omitted, all lines are returned.
180 region_id returned from @stats_create
194 region_id returned from @stats_create
|
| /Documentation/media/uapi/cec/ |
| D | cec-ioc-g-mode.rst | 33 File descriptor returned by :c:func:`open() <cec-open>`.
137 was specified, the ``EINVAL`` error code is returned in that case.
147 was specified, the ``EINVAL`` error code is returned in that case.
160 the ``EINVAL`` error code is returned in that case.
167 otherwise the ``EINVAL`` error code will be returned.
169 capability is set, otherwise the ``EINVAL`` error code is returned.
174 capability. If that is not set, then the ``EPERM`` error code is returned.
181 otherwise the ``EINVAL`` error code will be returned.
187 that is not set, then the ``EPERM`` error code is returned.
194 the ``EINVAL`` error code will be returned. In 'monitor all' mode all messages
[all …]
|
| /Documentation/w1/slaves/ |
| D | w1_ds2438.rst | 37 An I/O error is returned when there is a problem setting the new value.
45 to userspace, otherwise an I/O error is returned.
53 Important: The returned value has to be divided by 256 to get a real
68 After the voltage conversion the value is returned as decimal ASCII.
|
| /Documentation/media/uapi/v4l/ |
| D | tuner.rst | 24 returned by the :ref:`VIDIOC_ENUMINPUT` ioctl is
34 struct :c:type:`v4l2_tuner` returned by :ref:`VIDIOC_G_TUNER <VIDIOC_G_TUNER>`
44 returned by the :ref:`VIDIOC_QUERYCAP` ioctl when the
56 :c:type:`v4l2_output` returned by the
78 :c:type:`v4l2_capability` returned by the
|
12345678910>>...22